共查询到18条相似文献,搜索用时 203 毫秒
1.
分别使用2维和3维分形方法对单点金刚石车削加工的KDP晶体表面形貌进行了分析,并对表面的3维分形维数和3维粗糙度表征参数进行了比较,分析了二者对表面形貌表征的差异。使用2维轮廓分形方法计算了KDP晶体表面圆周各方向上的分形维数。通过分析得出:3维分形维数与表面粗糙度值成反比关系;使用单点金刚石车削方法加工KDP晶体会形成各向异性特征明显的已加工表面,在一定程度上容易形成小尺度波纹;已加工表面是否具有明显的小尺度波纹特征与表面粗糙度值并无直接关系,但与其表面轮廓分形状态分布密切相关;KDP晶体表面2维功率谱密度与其分形状态具有相近的方向性特征。 相似文献
2.
采用傅里叶模方法,分析了单点金刚石铣削后KDP晶体表面小尺度波纹的周期和幅值对单层增透膜折射率、厚度以及透射率的影响。研究表明:膜层最佳折射率在1.22左右,在此折射率条件下,保证透射率大于99%的单层增透膜的理想厚度范围应为180~220 nm,并且折射率和膜厚值的选取基本不受晶体表面小尺度波纹周期和幅值的影响。若只考虑SPDT法加工后KDP晶体表面小尺度波纹周期和幅值的实际范围,透射率基本不受波纹周期的影响,但却会随波纹幅值的增大而加速下降。理想镀膜条件下透射率最大值大于99%,并且通常在99.67%~99.94%之间。 相似文献
3.
采用傅里叶模方法,分析了单点金刚石铣削后KDP晶体表面小尺度波纹的周期和幅值对单层增透膜折射率、厚度以及透射率的影响。研究表明:膜层最佳折射率在1.22左右,在此折射率条件下,保证透射率大于99%的单层增透膜的理想厚度范围应为180~220 nm,并且折射率和膜厚值的选取基本不受晶体表面小尺度波纹周期和幅值的影响。若只考虑SPDT法加工后KDP晶体表面小尺度波纹周期和幅值的实际范围,透射率基本不受波纹周期的影响,但却会随波纹幅值的增大而加速下降。理想镀膜条件下透射率最大值大于99%,并且通常在99.67%~99.94%之间。 相似文献
4.
5.
《光学学报》2010,(4)
高精度KDP晶体是惯性约束核聚变光路系统中的重要元件,而已加工表面的小尺度波纹对光学元件的透射比有着重要影响。采用傅里叶模方法理论分析了表面小尺度波纹的幅值及周期对KDP光学元件透射比的影响。研究结果表明,当小尺度波纹幅值小于100 nm时,透射比随波纹幅值的增加基本呈线性增长,波纹幅值每提高10 nm.透射比可提高近0.5%;透射比随着小尺度波纹周期的增加围绕中心透射比上下浮动,透射比振幅基本保持不变.且中心透射比及透射比振幅均随着小尺度波纹幅值的增加而增大;小尺度波纹周期在10.5~12μm区间内时透射比明显很低,需采取措施避免小尺度波纹的周期出现在此区间。对KDP晶体进行了加工、表面形貌检测及透射比检测的实验,实验结果与理论计算结果基本吻合。 相似文献
6.
7.
8.
9.
针对采用单点金刚石超精加工的KDP晶体光学表面,研究了切削参数对微观形貌频率特征的影响。通过功率谱密度获得表面轮廓频率分布,并用连续小波重构加工过程中随切削用量变化的微观轮廓频率特征。结果表明:切削参数对微观形貌的影响具体表现在实际频率特征上,中频特征波长及幅值反映了切深及转速变化,随切深及转速增加,幅值变大;低频特征反映了进给量变化,随着进给量变小,频率及幅值变小;高频特征是加工过程中振动及材料各向异性的具体表现。 相似文献
10.
王守义刘卫国李世杰惠迎雪周顺冯瑶 《光学技术》2020,(6):757-762
KDP晶体在惯性约束核聚变光学系统中具有十分重要的作用,针对如何制造出满足应用要求的KDP晶体元件仍然是一个难点的问题。进行了采用飞切加工技术对KDP晶体平面元件的加工工艺研究。介绍了飞切加工的技术原理,以及影响表面粗糙度的因素;通过相应的工艺实验,对KDP晶体加工检测过程中可能影响表面粗糙度的各个因素进行了研究。实验结果表明:金刚石刀具参数、加工参数、以及加工后表面清洁方式都会影响表面粗糙度,但是金刚石刀具参数对表面粗糙度的影响最大。采用前角为-45°、圆弧半径为5.0mm的金刚石刀具,以及最优的加工参数,可以获得表面粗糙度Sa优于1nm的超光滑表面。研究结果对飞切加工KDP晶体平面元件提供了有效的工艺方案,具有广泛的工程应用价值。 相似文献
11.
The wavelet analysis method has been extensively employed to analyze the surface structures and evaluate the surface roughness. In this work, however, the wavelet analysis method was introduced to decompose and reconstruct the sampled surface profile signals in the cutting direction that achieved by SPDT (single point diamond turning) operation, and the surface profile signals in tool feeding direction were reconstructed with the approximate harmonic functions directly. And moreover, the orthogonal design method, i.e. the combination design of general rotary method, was resorted to model the variations of the independent frequency and amplitude of different simulated harmonic signals in the cutting and tool feeding directions. As expected resultantly, a novel 3D surface topography modeling solution was established, which aims to predict and modify the finished KDP (potassium dihydrogen phosphate or KH2PO4) crystal surfaces. The validation tests were carried out finally under different cutting conditions, and the collected average surface roughness in any case was compared with the corresponding value as predicted. The results indicated the experimental data were well consistent with the predictions, and only an average relative error of 11.4% occurred in predicting the average surface roughness. 相似文献
12.
使用有限元方法分析了在激光辐照条件下,KDP晶体已加工表面存在的残余内应力、微裂纹及微孔等多种微纳米加工表层缺陷对晶体激光损伤阈值的影响。通过分析发现:KDP晶体微纳米加工表层缺陷的存在,会影响晶体表面的温度场及热应力场的分布,使入射激光的能量积聚在缺陷附近的很小范围内,造成晶体缺陷处产生局部熔融现象,从而使KDP晶体产生损伤,降低KDP晶体的激光损伤阈值。针对微纳米表层的微裂纹进行了损伤阈值测试实验,结果表明微裂纹的存在会降低KDP晶体的激光损伤阈值(约降低3 J/cm2),实验结果与仿真结果符合得很好。 相似文献
13.
使用有限元方法分析了在激光辐照条件下,KDP晶体已加工表面存在的残余内应力、微裂纹及微孔等多种微纳米加工表层缺陷对晶体激光损伤阈值的影响。通过分析发现:KDP晶体微纳米加工表层缺陷的存在,会影响晶体表面的温度场及热应力场的分布,使入射激光的能量积聚在缺陷附近的很小范围内,造成晶体缺陷处产生局部熔融现象,从而使KDP晶体产生损伤,降低KDP晶体的激光损伤阈值。针对微纳米表层的微裂纹进行了损伤阈值测试实验,结果表明微裂纹的存在会降低KDP晶体的激光损伤阈值(约降低3J/cm2),实验结果与仿真结果符合得很好。 相似文献
14.
15.
A fractal dimension for roughness height (RH) is introduced to characterize the degree of roughness or disorder of particle surface characters which significantly influence physical-chimerical processes in porous media. An analytical expression for the fractal dimension of RH on statistically self-similar fractal surfaces is derived and is expressed as a function of roughness parameters. The specific surface area (SSA) of porous materials with spherical particles is also derived, and the proposed fractal model for the SSA of particles with rough surfaces is expressed as a function of fractal dimension for RH and fractal dimension for particle size distribution, relative roughness of particle surface, and ratio of the minimum to the maximum particle diameters of spherical particles. 相似文献
16.
17.
We report on the fractal analysis of digital speckle patterns experimentally generated using an optical setup to record the light scattered from metallic rough surfaces in the normal direction. Using the differential box counting technique, we have calculated the fractal dimension of digital speckle patterns for six samples with different roughness. Our results show a quadratic dependence between the surface roughness and the fractal dimension of the corresponding digital speckle pattern. As an application a method to determine the surface roughness of metallic surfaces is proposed. 相似文献
18.
Yevgen Grynko Sorin Pulbere 《Journal of Quantitative Spectroscopy & Radiative Transfer》2009,110(14-16):1382-1391
We study light reflection from flat particles with rough surfaces and fractal statistics of topography. Discrete dipole approximation method is used to solve the problem of light scattering. Refractive indices corresponding to a metal and a transient material with conductive properties are taken. The sizes of particles are much larger than the wavelength of incident light and the roughness scales are larger, comparable to and smaller than the wavelength. The influence of the fractal dimension parameter and the amplitude of heights of random topography on reflectance and on the angular profile of the specular reflection peak is considered. Our calculations demonstrate that topography amplitude is very important for reflectance and fractal dimension is responsible for the angular dispersion of the specular reflection peak. 相似文献