Spontaneous formation of cluster array of gold particles by convective self-assembly

Cluster arrays composed of metal nanoparticles are promising for application in sensing devices because of their interesting surface plasmon characteristics. Herein, we report the spontaneous formation of cluster arrays of gold colloids on flat substrates by vertical-deposition convective self-assembly. In this technique, under controlled temperature, a hydrophilic substrate is vertically immersed in a colloid suspension. Cluster arrays form when the particle concentration is extremely low (in the order of 10(-6)-10(-8) v/v). These arrays are arranged in a hierarchically ordered structure, where the particles form clusters that are deposited at a certain separation distance from each other, to form "dotted" lines that are in turn aligned with a constant spacing. The size of the cluster can be controlled by varying the particle concentration and temperature while an equal separation distance is maintained between the lines formed by the clusters. Our technique thus demonstrates a one-step, template-free fabrication method for cluster arrays. In addition, through the direct observation of the assembly process, the spacing between the dotted lines is found to result from the "stick-and-slip" behavior of the meniscus tip, which is entirely different from the formation processes observed for the striped patterns, which we reported previously at higher particle concentrations. The difference in the meniscus behavior possibly comes from the difference in colloidal morphology at the meniscus tip. These results demonstrate the self-regulating characteristics of the convective self-assembly process to produce colloidal patterns, whose structure depends on particle concentration and temperature.     

Patterned assembly of colloidal particles by confined dewetting lithography

We report the assembly of colloidal particles into confined arrangements and patterns on various cleaned and chemically modified solid substrates using a method which we term "confined dewetting lithography" or CDL for short. The experimental setup for CDL is a simple deposition cell where an aqueous suspension of colloidal particles (e.g., polystyrene spheres) is placed between a floating deposition template (i.e., metal microgrid) and the solid substrate. The voids of the deposition template serve as an array of micrometer-sized reservoirs where several hydrodynamic processes are confined. These processes include water evaporation, meniscus formation, convective flow, rupturing, dewetting, and capillary-bridge formation. We discuss the optimal conditions where the CDL has a high efficiency to deposit intricate patterns of colloidal particles using polystyrene spheres (PS; 4.5, 2.0, 1.7, 0.11, 0.064 microm diameter) and square and hexagonal deposition templates as model systems. We find that the optimization conditions of the CDL method, when using submicrometer, sulfate-functionalized PS particles, are primarily dependent on minimizing attractive particle-substrate interactions. The CDL methodology described herein presents a relatively simple and rapid method to assemble virtually any geometric pattern, including more complex patterns assembled using PS particles with different diameters, from aqueous suspensions by choosing suitable conditions and materials.     

Collodial cluster arrays by electrohydrodynamic printing

A "stable" electrohydrodynamic jet is used to print arrays of colloidal suspensions on hydrophobic surfaces. Printed lines break up into sessile drops, and capillary forces guide the self-assembly of colloidal particles during the evaporation of the liquid, resulting in arrays of colloidal single particles or particle clusters depending on the concentration of the suspensions. The clusters differ from those formed in the absence of a substrate when the number of particles is larger than three. Multiple structures are found for the same number of particles.     

悬浮液气-液界面二元胶体颗粒的漂浮组装机理

提出一种在悬浮液气-液界面漂浮组装亚微米单分散聚苯乙烯(PS)微球和纳米SiO2颗粒二元胶粒晶体的新方法, 并系统研究了漂浮组装机理. 研究表明, 聚苯乙烯微球和二氧化硅两种胶体颗粒在悬浮液气-液界面的漂浮组装是以PS微球的组装为主导的. 在一定PS微球相浓度范围内, 悬浮液中PS 微球与SiO2颗粒的初始体积配比基本不影响PS微球有序组装的形成. PS微球粒径在150-500 nm时易于形成有序排列, 较小或较大粒径的PS微球难以形成有序排列. SiO2颗粒的组装是一种以PS微球为“基底”的沉积过程. 二元胶粒晶体中SiO2颗粒的体积分数由其在混合悬浮液中的相浓度所决定.     

Controlled particle placement through convective and capillary assembly

A wide variety of methods are now available for the synthesis of colloidal particle having controlled shapes, structures, and dimensions. One of the main challenges in the development of devices that utilize micro- and nanoparticles is still particle placement and integration on surfaces. Required are engineering approaches to control the assembly of these building blocks at accurate positions and at high yield. Here, we investigate two complementary methods to create particle assemblies ranging from full layers to sparse arrays of single particles starting from colloidal suspensions of gold and polystyrene particles. Convective assembly was performed on hydrophilic substrates to create crystalline mono- or multilayers using the convective flow of nanoparticles induced by the evaporation of solvent at the three-phase contact line of a solution. On hydrophobic surfaces, capillary assembly was investigated to create sparse arrays and complex three-dimensional structures using capillary forces to trap and organize particles in the recessed regions of a template. In both methods, the hydrodynamic drag exerted on the particle in the suspension plays a key role in the assembly process. We demonstrate for the first time that the velocity and direction of particles in the suspension can be controlled to perform assembly or disassembly of particles. This is achieved by setting the temperature of the colloidal suspension above or below the dew point. The influence of other parameters, such as substrate velocity, wetting properties, and pattern geometry, is also investigated. For the particular case of capillary assembly, we propose a mechanism that takes into account the relative influences of these parameters on the motion of particles and that describes the influence of temperature on the assembly efficiency.     

Colloidal liquid crystal type assemblies of spheroidal polystyrene core/polyglycidol‐rich shell particles (P[S/PGL]) formed at the liquid‐silicon‐air interface by a directed dewetting process

A method for the preparation of stripe‐like monolayers of microspheroids is described. The particles were obtained from polystyrene core/polyglycidol‐rich shell microspheres by stretching poly (vinyl alcohol) films that contain embedded particles. The stretching was performed under controlled conditions at temperatures above the T_g of the films and particles. The elongated films were dissolved in water, and the microspheroids were subsequently removed and purified from the poly (vinyl alcohol). The aspect ratio (AR) of the particles, which denotes the ratio of the lengths of the longer to shorter particle axes, was determined by the film elongation. The AR values were in the range of 2.9‐7.7. Spheroidal particles with various ARs were deposited onto silicon wafers from an ethanol (EtOH) suspension. The particle concentration and volume of the suspension were the same in each experiment. Evaporation of the EtOH yielded stripes of spherical particles packed into nematic‐type colloidal crystals and assembled into monolayers. The orientation of the stripes after ethanol evaporation was perpendicular to the triphasic (silicon‐ethanol‐air) interface along the silicon substrate. The adsorbed stripes on the wafers were characterized in terms of their interstripe distance (ID), stripe width, and crystal domain size. Nematic‐type spheroid arrangements in the stripes were the dominant structure, which enabled denser packing of the particles into colloidal crystals than that allowed by the smectic‐type arrangements. Furthermore, the number of spheroids adsorbed per surface unit of the silicon wafers was similar for all ARs, but the width and frequency of the spheroid stripes adsorbed on the wafers were different.     

Kinetic stages of single-component colloidal crystallization

To harness the full potential of colloidal self-assembly, the dynamics of the transition between colloids in suspension to a colloidal crystalline film should be better understood. In this report, the structural changes during the self-assembly process in a vertical configuration for colloids in the size range 200-400 nm are monitored in situ, using the transmission spectrum of the colloidal assembly treated as an emergent photonic crystal. It is found that there are several sequential stages of colloidal ordering: in suspension, with a larger lattice parameter than the solid state, in a close-packed wet state with solvent in the interstices, and, finally, in a close-packed dry state with air in the interstices. Assuming that these stages lead continuously from one to another, we can interpret colloidal crystallization as being initiated by interparticle forces in suspension first, followed by capillary forces. This result has implications for identifying the optimum conditions to obtain high-quality nanostructures of submicrometer-sized colloidal particles.     

A universal approach to fabricate ordered colloidal crystals arrays based on electrostatic self-assembly

We present a novel and simple method to fabricate two-dimensional (2D) poly(styrene sulfate) (PSS, negatively charged) colloidal crystals on a positively charged substrate. Our strategy contains two separate steps: one is the three-dimensional (3D) assembly of PSS particles in ethanol, and the other is electrostatic adsorption in water. First, 3D assembly in ethanol phase eliminates electrostatic attractions between colloids and the substrate. As a result, high-quality colloidal crystals are easily generated, for electrostatic attractions are unfavorable for the movement of colloidal particles during convective self-assembly. Subsequently, top layers of colloidal spheres are washed away in the water phase, whereas well-packed PSS colloids that are in contact with the substrate are tightly linked due to electrostatic interactions, resulting in the formation of ordered arrays of 2D colloidal spheres. Cycling these processes leads to the layer-by-layer assembly of 3D colloidal crystals with controllable layers. In addition, this strategy can be extended to the fabrication of patterned 2D colloidal crystals on patterned polyelectrolyte surfaces, not only on planar substrates but also on nonplanar substrates. This straightforward method may open up new possibilities for practical use of colloidal crystals of excellent quality, various patterns, and controllable fashions.     

Particle Network Self-Assembly of Similar Size Sub-Micron Calcium Alginate and Polystyrene Particles Atop Glass

Particle-mediated self-assembly, such as nanocomposites, microstructure formation in materials, and core-shell coating of biological particles, offers precise control over the properties of biological materials for applications in drug delivery, tissue engineering, and biosensing. The assembly of similar-sized calcium alginate (CAG) and polystyrene sub-micron particles is studied in an aqueous sodium nitrate solution as a model for particle-mediated self-assembly of biological and synthetic mixed particle species. The objective is to reinforce biological matrices by incorporating synthetic particles to form hybrid particulate networks with tailored properties. By varying the ionic strength of the suspension, the authors alter the energy barriers for particle attachment to each other and to a glass substrate that result from colloidal surface forces. The particles do not show monotonic adsorption trend to glass with ionic strength. Hence, apart from DLVO theory—van der Waals and electrostatic interactions—the authors further consider solvation and bridging interactions in the analysis of the particulate adsorption-coagulation system. CAG particles, which support lower energy barriers to attachment relative to their counterpart polystyrene particles, accumulate as dense aggregates on the glass substrate. Polystyrene particles adsorb simultaneously as detached particles. At high electrolyte concentrations, where electrostatic repulsion is largely screened, the mixture of particles covers most of the glass substrate; the CAG particles form a continuous network throughout the glass substrate with pockets of polystyrene particles. The particulate structure is correlated with the adjustable energy barriers for particle attachment in the suspension.     

Rheology of binary colloidal structures assembled via specific biological cross-linking

The selectivity and range of energies offered by specific biological interactions serve as valuable tools for engineering the assembly of colloidal particles into novel materials. In this investigation, high affinity biological interactions between biotin-coated "A" particles (RA = 0.475 microm) and streptavidin-coated "B" particles (RB = 2.75 microm) drive the self-assembly of a series of binary colloidal structures, from colloidal micelles (a large B particle coated by smaller A particles) to elongated chain microstructures (alternating A and B particles), as the relative number of small (A) to large (B) particles (2 < or = NA/NB < or = 200) is decreased at a low total volume fraction (10(-4) < or = phiT < or = 10(-3)). At a significantly higher total volume fraction (phiT > or = 10(-1)) and a low number ratio (NA/NB = 2), the rheological behavior of volume-filling particle networks connected by streptavidin-biotin bonds is characterized. The apparent viscosity (eta) as a function of the shear rate gamma, measured for networks at phiT = 0.1 and 0.2, exhibits shear-rate-dependent flow behavior, and both the apparent viscosity and the extent of shear thinning increase upon an increase of a factor of 2 in the total volume fraction. Micrographs taken before and after shearing show a structural breakdown of the flocculated binary particle network into smaller flocs, and ultimately a fluidlike suspension, with increasing shear rate. Rheological measurements provide further proof that suspension microstructure is governed by specific biomolecular interactions, as control experiments in which the streptavidin molecules on particles were blocked displayed Newtonian flow behavior. This investigation represents the first attempt at measuring the rheology of colloidal suspensions where assembly is driven by biomolecular cross-linking.     

Facile fabrication of mechanochromic-responsive colloidal crystal films

This paper presents a simple approach to fabricate a reversible mechanochromic-responsive crystal film based on the room-temperature film-formation of monodisperse polymer latex by the aid of nanosilica particles. In this approach, when the "soft" colloidal polymer spheres were blended with colloidal silica particles and then cast on a substrate, followed by drying at room temperature for self-assembly, an elastic crystal film was directly obtained. This crystal film has not only reversible and repeatable mechanochromic-responsive property, but also tunable color and peak position covering almost entire visible spectral region, depending upon the sizes of polymer spheres and strains. This optical response is attributed to the variation of lattice spacing during deformation.     

Mechanistic principles of colloidal crystal growth by evaporation-induced convective steering

We simulate evaporation-driven self-assembly of colloidal crystals using an equivalent network model. Relationships between a regular hexagonally close-packed array of hard, monodisperse spheres, the associated pore space, and selectivity mechanisms for face-centered cubic microstructure propagation are described. By accounting for contact line rearrangement and evaporation at a series of exposed menisci, the equivalent network model describes creeping flow of solvent into and through a rigid colloidal crystal. Observations concerning colloidal crystal growth are interpreted in terms of the convective steering hypothesis, which posits that solvent flow into and through the pore space of the crystal may play a major role in colloidal self-assembly. Aspects of the convective steering and deposition of high-Peclet-number rigid spherical particles at a crystal boundary are inferred from spatially resolved solvent flow into the crystal. Gradients in local flow through boundary channels were predicted due to the channels' spatial distribution relative to a pinned free surface contact line. On the basis of a uniform solvent and particle flux as the criterion for stability of a particular growth plane, these network simulations suggest the stability of a declining {311} crystal interface, a symmetry plane which exclusively propagates fcc microstructure. Network simulations of alternate crystal planes suggest preferential growth front evolution to the declining {311} interface, in consistent agreement with the proposed stability mechanism for preferential fcc microstructure propagation in convective assembly.     

Reactivity of nanocolloidal particles gamma-Fe2O3 at the charged interfaces. Part 1. The approach of particles to an electrode

We are interested here in the reactivity of magnetic nanoparticles at the electrode-electrolyte interface with the aim of the electrochemical synthesis of magnetic and conductive liquids (electronic conduction). The reactivity of charged colloidal particles occurs through a two steps process, the first being the approach toward the electrode with a possible adsorption phenomenon and the second step, the electron transfer. In this first paper we focus on the approach and the deposition of well-defined gamma-Fe(2)O(3) nanoparticles onto conductive substrates like mercury and gold under different conditions in order to vary the interactions particle/substrate especially the electrostatic interactions. The approach of the particles near the electrodes is estimated from the electrochemical currents related to the transformation of the particles. This electrochemical method is validated by coupling several techniques on gold electrodes: direct imaging by atomic force microscopy and study of kinetics by reflectometry. The results show that the electrochemical currents are always associated to adsorption of the particles, so that the electrochemical method can be used to estimate the adsorption of the particles, thus to follow the kinetics. The influence of the electrostatics on the occurrence of adsorption highly depends on the nature of the substrate and on the nature of the colloidal suspension. (ions, pH, ionic strength): whereas electrostatics governs the deposits in some cases, it is totally dominated by other interactions in other cases. Therefore, it seems difficult to predict a priori the existence of adsorption. However, when a deposit occurs, the kinetics and the maximal coverage of the substrates are controlled by the electrostatic interactions between the particles already adsorbed and those, close to the interface, in the bulk of the solution.     

Parameters influencing the templated growth of colloidal crystals on chemically patterned surfaces

The influence of various experimental parameters on the vertical deposition and structure formation of colloidal crystals on chemically patterned surfaces, with hydrophilic and hydrophobic areas, was investigated. The pattern dimensions range from about 4 to 400 microm, which is much larger than the individual particle size (255 nm), to control the microscopic crystal shape rather than influencing the crystal lattice geometry (as achieved in colloidal epitaxy). The deposition resolution and selectivity were tested by varying the particle concentration in the suspension, the substrate withdrawing speed, pattern size and orientation, and wetting contrast between the hydrophilic and hydrophobic regions. The evolution of colloidal crystal thickness with respect to the pattern dimensions and deposition parameters was further studied. Our results show that the pattern size has a rather strong influence on the deposited number of colloid layers and on the crystal quality. Better results are obtained when the lines of a stripe pattern are oriented parallel to the withdrawing direction rather than perpendicular. The deposition resolution (defined as the minimum feature size on which particles can be deposited) depends on the wetting contrast and increases with lower average hydrophobicity of the substrate.     

Evaporative self-assembly from complex DNA-colloid suspensions

Evaporation-induced pattern formation has attracted considerable attention as a simple yet versatile method for generating self-assembled structures that have broad applications from photonic devices to biomacromolecular recognition. Previous study of evaporative self-assembly has mainly focused on single nonvolatile component systems, and the driving mechanisms have been extensively investigated. In contrast, pattern formation from evaporating multicomponent systems, despite its wide existence in nature and numerous engineering applications, has been rarely explored. In this work, we examine a DNA-colloid binary suspension as a model system to understand the evaporation-induced interfacial hydrodynamics and self-assembled morphology in multicomponent systems involving complex competing intermolecular and interfacial interactions. Direct microscopic observations show that the composition of the binary system plays a critical role in the multiple-ring formation upon evaporation: (1) suspensions with high DNA concentrations and low colloidal concentrations favor the formation of the multiple-ring pattern; (2) the size of colloidal particles added into DNA aqueous droplets can significantly disrupt smooth multiple rings to form rippled rings and curtain-like periodic patterns with a curious spoke-like structure as the size of colloidal particles increases; and (3) the enhancement of DNA-colloid interaction by oppositely charged colloidal particles results in considerably high irregularity of DNA stain ring spacing. We examine the disruption of the multiring morphology under varied conditions and attribute it to local hydrodynamics governed by colloid aggregation and sedimentation. Our results demonstrate the feasibility of fabricating periodic self-assembled hybrid structures via one-step evaporation of droplets consisting of multiple components.     

SiO2胶体颗粒的三维有序自组装

由SiO2胶体颗粒的三维有序自组装可以得到面心立方三维结构,它具有折射率周期性变化的特点。它的制备涉及胶体化学、材料科学等学科的前沿领域。其自组装方法包括胶体颗粒的沉降自组装、胶体颗粒在物体限制下的自组装、胶体颗粒的连续对流自组装和利用胶体颗粒表面电性质的自组装。本文对这些组装方法进行了介绍。     

Engineering DNA-mediated colloidal crystallization

DNA is a powerful and versatile tool for nanoscale self-assembly. Several researchers have assembled nanoparticles and colloids into a variety of structures using the sequence-specific binding properties of DNA. Until recently, however, all of the reported structures were disordered, even in systems where ordered colloidal crystals might be expected. We detail the experimental approach and surface preparation that we used to form the first DNA-mediated colloidal crystals, using 1 mum diameter polystyrene particles. Control experiments based on the depletion interaction clearly indicate that two standard methods for grafting biomolecules to colloidal particles (biotin/avidin and water-soluble carbodiimide) do not lead to ordered structures, even when blockers are employed that yield nominally stable, reversibly aggregating dispersions. In contrast, a swelling/deswelling-based method with poly(ethylene glycol) spacers resulted in particles that readily formed ordered crystals. The sequence specificity of the interaction is demonstrated by the crystal excluding particles bearing a noninteracting sequence. The temperature dependence of gelation and crystallization agree well with a simple thermodynamic model and a more detailed model of the effective colloidal pair interaction potential. We hypothesize that the surfaces yielded by the first two chemistries somehow hinder the particle-particle rolling required for annealing ordered structures, while at the same time not inducing a significant mean-force interaction that would alter the self-assembly phase diagram. Finally, we observe that particle crystallization kinetics become faster as the grafted-DNA density is increased, consistent with the particle-particle binding process being reaction, rather than diffusion limited.     

Particle and substrate charge effects on colloidal self-assembly in a sessile drop

By direct video monitoring of dynamic colloidal self-assembly during solvent evaporation in a sessile drop, we investigated the effect of surface charge on the ordering of colloidal spheres. The in situ observations revealed that the interaction between charged colloidal spheres and substrates affects the mobility of colloidal spheres during convective self-assembly, playing an important role in the colloidal crystal growth process. Both ordered and disordered growth was observed depending on different chemical conditions mediated by surface charge and surfactant additions to the sessile drop system. These different self-assembly behaviors were explained by the Coulombic and hydrophobic interactions between surface-charged colloidal spheres and substrates.     

An improved convective self-assembly method for the fabrication of binary colloidal crystals and inverse structures

We report an improved convective self-assembly method for the fabrication of highly ordered, crack-free binary colloidal crystals (BCCs) and the associated inverse structures in large domains at length scales of several centimeters. With this method, BCCs can be fabricated in a non-close packed pattern and binary inverse opal films can be obtained over a centimeter scale. The presence of tetraethyl orthosilicate (TEOS) sol in the self-assembly system was found to play a significant role in the resultant structures. The pseudostop band positions are adjustable via varying the number ratio of small to large polystyrene (PS) spheres. At a given TEOS-to-PS ratio, the binary inverse opal film thickness was controllable by varying the colloidal volume fraction with an upper thickness threshold (>16 layers).     

Theoretical analysis of vertical colloidal deposition

We have modeled the dynamics of a relatively new deposition technique, vertical colloidal deposition (VCD), for preparing nanoparticle thin films. In this process, the substrate is placed vertically in a nanoparticle suspension and is gradually exposed by evaporation or other slow solvent removal. During the film's formation, we observe that the colloidal particles are deposited only at the solid-liquid-gas interface. In contrast with the horizontal geometry, treated elsewhere, where the meniscus is pinned, we observe qualitatively different deposition behaviors. In particular, uniform films rather than rings or lines are produced. Thus, we are led to model a diffusion-driven rather than a convection-driven film growth kinetics, and we are able to predict, consistent with our experimental observations, that the film's areal density is inversely proportional to the descent speed of the suspension surface. Additionally, we find that for submonolayer films, the areal density is proportional to the square of the suspension concentration, converting to a linear dependence once monolayer coverage is attained.