Anomalies in evaporative light scattering detection

A two-dimensional (2-D) “heart-cutting” HPLC system was used to fractionate oligostyrenes into the respective diastereoisomers. For samples of known composition, the response of an ultraviolet (UV) absorbance detector followed the anticipated pattern. The response of an evaporative light-scattering (ELSD) detector on the other hand indicated quite different concentrations for the two diastereoisomers, relative to what was anticipated and what was indicated by the UV detector. Whereas approximately the same concentration was indicated by UV, ELSD in some cases indicated no detection of the later eluting isomer. The magnitude of the errors depended on both the molecular weight and the tacticity of the diastereomers. These anomalies appear to be an artifact of power transform functions imbedded within the firmware processor of the ELSD, invisible to the user.     

Separation ofAstragalus saponins by reversed phase high performance liquid chromatography and evaporative light scattering detection

Summary A new HPLC method permitted the separation of 13 triterpene lycosides isolated from differentAstragalus species within 40 min. A water/acetonitrile gradient was used as eluent and 5 μm RP-18 material as stationary phase. By using an evaporative light scattering (ELS) detector, the main saponins ofA. membranaceus could be detected at levels as low as 20.0 μg·mL⁻¹. This method facilitated distinction of differentAstragalus species as well as the analyses of market products containingA. membranaceus. The results showed variations from 0.019 to 0.184% in the total saponin content of the market products.     

Performance evaluation of evaporative light scattering detection and charged aerosol detection in reversed phase liquid chromatography

In pharmaceutical industry ultraviolet (UV) detection is often used as the preferred detection technique in HPLC analysis since most pharmaceutical compounds possess a UV-absorbing chromophore. However, in case the active pharmaceutical ingredient (API) does not have a UV-absorbing chromophore, or if some of the impurities present lack a chromophore, they will not be detected in routine HPLC analysis employing only a UV detector and alternative detection schemes have to be used. Refractive index detection or mass spectroscopy (MS) can be used but these detectors have their intrinsic weaknesses, such as lack of sensitivity or high cost. With the appearance of semi-universal techniques such as evaporative light scattering detection (ELSD), and more recent, charged aerosol detection (CAD), detection of non-UV-absorbing compounds became feasible without having to resort to such complex or costly detection methods. This paper evaluates the different performance characteristics such as sensitivity, linearity, accuracy and precision of both the ELSD and CAD detector coupled to HPLC. One disadvantage of this type of detector is the non-linear response behaviour which makes direct linear regression for making calibration curves inaccurate.     

Separation of monosaccharides by hydrophilic interaction chromatography with evaporative light scattering detection

Hydrophilic interaction liquid chromatography (HILIC) was used to separate monosaccharides that are common in N-linked oligosaccharides in glycoproteins and other compounds. A TSKgel Amide-80 column was eluted with 82% acetonitrile, in 5 mM ammonium formate (pH 5.5). Column temperature was 60 degrees C and evaporative light scattering was used for detection (ELSD). With this method, L-fucose, D-galactose, D-mannose, N-acetyl-D-glucosamine, N-acetylneuraminic acid, and D-glucuronic acid were separated, with detection limits of 0.3-0.5 microg for each monosaccharide, and intermediate precisions were 3-6% RSD (n=6).     

Separation ofCimicifuga racemosa triterpene glycosides by reversed phase high performance liquid chromatography and evaporative light scattering detection

Summary The main triterpene glycosides ofCimicifuga racemosa were separated by reversed phase HPLC, using a C-18 column, Evaporative Light Scattering (ELS) detection and a grient system consisting of water, acetonitrile and reagent alcohol. Within 35 min three main glycosides could be separated and quantified in the methanolic root extract with detection limits of 10.5, 15.6 and 31.6 μg·mL⁻¹ respectively. The method was successfully used, to analyzed differentCimicifuga racemosa market products, as well as to distinguish between otherCimicifuga samples from China.     

Determination of N,N'-ethylenebisstearamide additive in polymer by normal phase liquid chromatography with evaporative light scattering detection

A new method for N,N'-ethylenebisstearamide (EBS) analysis was developed and validated in normal phase-HP liquid chromatography (NP-HPLC) with diol column at 50 degrees C with 100% CHCl(3) at 1 mL min(-1) and evaporative light scattering detection with elution time at 3.0 min. EBS solubility was the best at 0.80 gL(-1) in CHCl(3)/methanol 90:10. The molecular structure of commercial samples of EBS was determined by GC-MS which ascertained that the main structure is C18/C18 at approximately 45%. The remaining part was constituted by molecules with different alkyl chain length. The HPLC quantification method was proved linear (r=0.9983), accurate (99.6%) and precise (1.95%). Limit of quantification (LOQ) and limit of detection (LOD) were equal to 2.0 and 0.8 microg mL(-1), respectively. The suitability of this method was assessed with a dissolution/precipitation extraction procedure of EBS from ethylene vinyl acetate (EVA) polymer which showed that other additives and polymer do not interfere with EBS analysis. The intra-day and day-to-day precisions of extraction method were equal to 9.1% and 9.9%, respectively.     

Mechanism of response enhancement in evaporative light scattering detection with the addition of triethylamine and formic acid

Triethylamine with an equimolar amount of formic acid added to the mobile phase provides an enhancement of the evaporative light scattering detector (ELSD) response. After characterization of the influence of various parameters on the ELSD response, a sequential strategy was defined to elucidate this response enhancement. The response enhancement was more marked at low mobile phase flow rate, and was highly dependent on solutes and solvents. The influence of drift tube temperature on response enhancement with various solutes demonstrated that triethylamine and formic acid mainly act as mass amplifiers by the inclusion of triethylamine-formic acid clusters inside the droplets.     

Development of a ginkgo biloba fingerprint chromatogram with UV and evaporative light scattering detection and optimization of the evaporative light scattering detector operating conditions

A fingerprint chromatogram of a standardized Ginkgo biloba extract is developed on a monolithic silica column using a ternary gradient containing water, iso-propanol and tetrahydrofuran. For the detection, UV and evaporative light scattering (ELS) detectors are used, the latter allowing detection of the poor UV absorbing compounds as ginkgolides (A-C and J) and bilobalide in the extract. The complementary information between the UV and ELS fingerprint is evaluated. The ELS detector used in this study can operate in an impactor 'on' or 'off' mode. For each mode, the operating conditions such as the nebulizing gas flow rate, the drift tube temperature and the gain are optimized by use of three-level screening designs to obtain the best signal-to-noise (S/N) ratio in the final ELS fingerprint chromatogram. In both impactor modes, very similar S/N ratios are obtained for the nominal levels of the design. However, optimization of the operating conditions resulted, for both impactor modes, in a significant increase in S/N ratios compared to the initial evaluated conditions, obtained from the detector software.     

Fingerprint analysis of Dioscorea nipponica by high-performance liquid chromatography with evaporative light scattering detection

High-performance liquid chromatographic method (HPLC) with evaporative light scattering detection (ELSD) coupled with microwave-assisted extraction (MAE) as an efficient sample preparation technique has been developed for fingerprint analysis of Dioscorea nipponica. The samples were separated with an Agilent C8 column using water (A) and acetonitrile (B) under gradient conditions (0-10 min, linear gradient 20-40% B; 10-12 min, linear gradient 40-42% B; 12-25 min, isocratic 42% B) as the mobile phase at a flow rate of 1 mL min⁻¹ within 22 min. The ELSD conditions were optimized at nebulizer-gas flow rate 2.7 L min⁻¹ and drift tube temperature 90 °C. Precision experiments showed relative standard deviation (R.S.D.) of peak area and retention time were better than 2.5%; inter-day and intra-day variabilities showed that R.S.D. was ranged from 0.78% to 4.74%. Limit of detection was less than 50 μg mL⁻¹ and limit of quantification was less than 80 μg mL⁻¹. Accuracy validation showed that average recovery was between 97.39% and 104.07%. The method was validated to achieve the satisfactory precision and recovery. Relative retention time and relative peak area were used to identify the common peaks for fingerprint analysis. There are nine common peaks in the fingerprint. The quality of seven batches of D. nipponica samples was evaluated to be qualified or unqualified by the parameters “difference” and “total difference” of common peaks. Furthermore, the contents of important medicinal compounds (dioscin, prodioscin and gracillin) in different batches of D. nipponica samples were determined simultaneously using the developed HPLC-ELSD method. The results indicated variation of the herb quality which might be related to different producing area, growing condition, climate, harvest time, drug processing and so on. The developed analytical procedure was proved to be a reliable and rapid method for the quality control of D. nipponica.     

Analysis of organosilicone copolymers by gradient polymer elution chromatography with evaporative light scattering detection

Organosilicone copolymers have found numerous applications in the cosmetics, detergent and coating industries. Coupling a polar polymer (like polyglycols) to a non-polar silicone gives anchorage and emulsification capabilities to the polymer. When coupling a silicone polymer to a polyglycol, the copolymer formed differs from the starting polymers by a single bond which is often difficult to evidence using spectroscopic techniques such as NMR or infrared, especially when the polymers have a high molecular mass. Gradient polymer elution chromatography (GPEC) coupled to an evaporative light scattering detector was developed for the characterization of copolymers based on their chemical composition distribution. Different block and graft polyglycol-silicone copolymers were successfully characterized by GPEC and residual homopolymers have been easily quantified.     

Comparison between evaporative light scattering detection and charged aerosol detection for the analysis of saikosaponins

Saikosaponins are triterpene saponins derived from the roots of Bupleurum falcatum L. (Umbelliferae), which has been traditionally used to treat fever, inflammation, liver diseases, and nephritis. It is difficult to analyze saikosaponins using HPLC-UV due to the lack of chromophores. Therefore, evaporative light scattering detection (ELSD) is used as a valuable alternative to UV detection. More recently, a charged aerosol detection (CAD) method has been developed to improve the sensitivity and reproducibility of ELSD. In this study, we compared CAD and ELSD methods in the simultaneous analysis of 10 saikosaponins, including saikosaponins-A, -B₁, -B₂, -B₃, -B₄, -C, -D, -G, -H and -I. A mixture of the 10 saikosaponins was injected into the Ascentis^® Express C18 column (100 mm × 4.6 mm, 2.7 μm) with gradient elution and detection with CAD and ELSD by splitting. We examined various factors that could affect the sensitivity of the detectors including various concentrations of additives, pH and flow rate of the mobile phase, purity of nitrogen gas and the CAD range. The sensitivity was determined based on the signal-to-noise ratio. The best sensitivity for CAD was achieved with 0.1 mM ammonium acetate at pH 4.0 in the mobile phase with a flow rate of 1.0 mL/min, and the CAD range at 100 pA, whereas that for ELSD was achieved with 0.01% acetic acid in the mobile phase with a flow rate at 0.8 mL/min. The purity of the nitrogen gas had only minor effects on the sensitivities of both detectors. Finally, the sensitivity for CAD was two to six times better than that of ELSD. Taken together, these results suggest that CAD provides a more sensitive analysis of the 10 saikosaponins than does ELSD.     

Use of evaporative light scattering detector in the detection and quantification of enantiomeric mixtures by HPLC

Routinely used in our laboratories at analytical scale, an evaporative light scattering detector (ELSD) has proved to be versatile in the detection of enantiomeric resolution using chiral stationary phases by HPLC. Though this kind of detector has been widely used in various domains, its application in enantiomeric resolution has not been discussed in the literature and is found to have very specific features especially in the quantitative perspective. In contrast with the UV detection, the peak area from ELSD for both enantiomers of a racemic mixture may not be the same. This complicates the assessment of the enantiomeric purity of unknown samples. This current work deals with some practical aspects in the detection of enantiomers and in accurate quantitative determination of enantiomeric purity by ELSD. Effects of analyte nature (more precisely molecular weight and volatility), peak shape and peak shape difference between enantiomers on the quantitative integration by ELSD are discussed in connection with the UV-detection results. The calibration for quantitative enantiomeric analysis and its effectiveness are demonstrated.     

Simultaneous separation of nine surfactants of various types by HPLC with evaporative light scattering detection

A simultaneous separation of cationic, amphoteric and nonioinc nine surfactants (DMDS, DMDP, DMDM, DMDL, BZC, CDE, A/O, SUNC, IMD) has been performed by a reverse phase-HPLC method utilizing a single J'sphere ODS (250 mm × 4.6 mm, 4 μm) column and a methanol-water containing 0.2% TFA eluent system within 60 min. The observed precision in determination of concentration was less than 5% R.S.D., which revealed that ELSD was an effective tool to detect the various studied surfactants of low volatility without chromophore. In addition, the detection limits were in the concentration range of 3.5-10 μg/mL, and the calibration curves, i.e. the log-log plots, were linear in the working range of 5-4600 μg/mL with the slopes of 1.321-1.668. The application of the analytical procedure to three household products without pretreatment supported that the presented chromatographic method was simple to be practical for a routine analysis of commercial products.     

离子对反相高效液相色谱-蒸发光散射检测法测定三乙膦酸铝的含量

建立了以正丁胺为离子对试剂的反相高效液相色谱分析三乙膦酸铝含量的方法。采用Symmetry Shield RP18色谱柱分离,以甲醇-0.5%正丁胺水溶液(冰乙酸调节pH 5.0)(体积比为8:92)为流动相,流速为0.8 mL/min,蒸发光散射检测器(ELSD)检测。在上述条件下,三乙膦酸铝与其主要杂质亚磷酸盐、硫酸盐可以获得分离。在100～1200 mg/L范围内,进样质量与峰面积的双对数值呈良好的线性关系。100 mg/L和1000 mg/L两种质量浓度添加水平的回收率分别为100.58%和99.53%,其相对标准偏差(RSD)分别为0.62%和0.49%。该方法简便快捷,为三乙膦酸铝的定量分析提供了更加有效可靠的方法。     

Analysis and purification of O-decanoyl sucrose regio-isomers by reversed phase high pressure liquid chromatography with evaporative light scattering detection

Purification of seven regio-isomers of O-decanoyl sucrose, 2-O-, 3-O-, 4-O-, 6-O-, 3′-O-, 4′-O- and 6′-O-decanoyl sucrose, were performed by LC followed by preparative RP-HPLC with ELSD. Using an optimized gradient of acetonitrile in water 2-O-, 3-O-, 6-O- and 3′-O-decanoyl sucrose were purified in yields (w/w) of 52.5%, 34.7%, 45.0% and 36.9%, respectively. In the purified preparations of the 2-O- and 3′-O-decanoyl sucrose respectively, acyl migration was observed as a result of the drying process. Lyophilization resulted in the highest purities (w/w) of 96% and 100% for the 2-O- and the 3′-O-decanoyl sucrose, respectively.     

Interference of chitosan in glucose analysis by high-performance liquid chromatography with evaporative light scattering detection

The purpose of this work was to quantify glucose in aqueous solutions containing chitosan by high-performance liquid chromatography (HPLC) with evaporative light scattering detection (ELSD). Chitosan is a natural compound that is used alone or as an additive in several formulations. Microencapsulation of bioactive compounds such as glucose, by means of chitosan, is being explored, but difficulties arise when glucose needs to be determined in the presence of chitosan. HPLC is the technique most commonly used for glucose analysis, and ELSD may offer advantages (e.g. sensitivity and the possibility of operating in gradient mode) compared with other detectors. The influence of chitosan in the analysis of glucose by HPLC with ELSD was investigated at different pH values of the aqueous solutions. Isocratic elution with an acetonitrile/water mixture (80:20, v/v) and water washing between runs were the best options to avoid the mucoadhesive properties of chitosan, which are responsible for column degradation and variability of the retention time of glucose. The developed methodology was considered completely adequate for rapid glucose analysis in aqueous solutions with low pH (< 3), in the presence of chitosan.     

Separation and quantification of beer carbohydrates by high-performance liquid chromatography with evaporative light scattering detection

An HPLC method with an evaporative light scattering detector was optimized and validated for quantification of carbohydrates in beer. The chromatographic separation was achieved using a Spherisorb NH2, 5 microm chromatographic column and gradient elution with acetonitrile/water. The determinations were performed in the linear range of 0.05-5.0 g/L for fructose, 0.05-5.0 g/L for glucose, 0.05-15.0 g/L for maltose, 0.05-10.0 g/L for maltotriose, and 0.05-5.0 g/L for maltotetraose. The detection limits were 0.005 g/L for fructose, 0.008 g/L for glucose, and 0.01 g/L for maltose, maltotriose, and maltotetraose. The reliability of the method in terms of precision and accuracy was evaluated in three beer matrices, low alcohol beer, 6% alcohol beer, and beer made with part of adjuncts (4.5% alcohol). Relative standard deviations (RSDs) ranged between 1.59 and 5.95% (n = 10), and recoveries ranged between 94 and 98.4%.     

Application of a xenon arc lamp as a light source for evaporative light scattering detection

The standard tungsten-halogen light source used in a commercial evaporative light scattering detector (ELSD) was replaced with a 180 W xenon arc lamp. The xenon arc lamp possesses a broader spectrum in the UV region than the halogen source. The influence of the UV transmittance of five selected solvents was studied with a size-exclusion chromatography column. This solvent parameter was not observed to influence the ELSD response between the two light source settings. With the solvents studied, better sensitivity was obtained with the xenon arc lamp than the halogen lamp. This high-energy source was applied to ceramide III analysis with an octadecyl-grafted silica column and methanol:tetrahydrofuran 97:3 as the mobile phase, and the sensitivity of the quantification of ceramide III increased 16-fold for injected amounts of 14∼140 ng. The molecular species in a sample of naturally occurring ceramides was analyzed using two C18 columns at 40 °C and gradient elution from 100% acetonitrile to 100% isopropanol in 30 min. The increased ELSD sensitivity achieved when using the xenon arc lamp allowed both the minor and major ceramide species to be observed, in contrast to the results achieved when the halogen lamp was used, where the increased photomultiplier voltage needed to observed the signals from the minor species caused the signals from the major ceramide species to occur above the detector response window.     

Linearization of evaporative light scattering detector signal

Recent advances in nebulizer technology of the evaporative light scattering detector (ELSD) allow the evaporation of trichlorobenzene (TCB) at much lower temperatures than the previous instruments, thus avoiding the sample loss in the lower molecular weight domain. Therefore, the new ELSD opens the possibility to correctly evaluate the molecular weight distribution (MWD) of polymers by gel permeation chromatography, after linearizing the ELSD signal intensity in function of concentration. To find the correct exponent parameter for linearization, it is necessary to take into account not only the peak area, but each point of the chromatogram. The evaluation method for this exponent parameter, found to be 1.61 for the analysis in TCB of polyolefin and polystyrene samples, is presented in this study. This value was verified by the excellent correlation found between the obtained MWD of a high-density polyethylene both with the ELSD and with the traditional differential refractive index detector.     

Continuous flow configuration for total hydrocarbons index determination in soils by evaporative light scattering detection

A continuous flow configuration is proposed for the estimation of the hydrocarbon index in soils using for the first time evaporative light scattering detection (ELSD). The method is based on a membrane-enrichment of the hydrocarbons of interest (C10-C40), which are previously extracted from the soil matrix with a water:hexane mixture using a household microwave oven. The organic supernatant is cleaned-up through silica, evaporated and redissolved in a sodium dodecyl sulphate aqueous solution which is introduced in the loop of an injection valve. The sample, carried by an aqueous stream, passes through a continuous filtration unit fitted with a 1 microm pore size PTFE membrane, where the hydrocarbons are retained while the potential coextracted compounds are wasted. Quantitative elution of the C10-C40 fraction is accomplished by passing an acetone stream through the filter which drives the analytes to the ELSD system for analytical measurement. The detection limit was 1.8 microg ml(-1), the linear range 5-25 microg ml(-1) and the precision 4.3%. The recoveries were between 93 and 97%. The proposed method was also evaluated by attenuated total reflexion-Fourier transform (ATR-FT-IR) analysis of the extracts.