Simultaneous determination of total and free calcium in milk by flow injection

A fast and reliable procedure for the determination of total and free calcium in milk is described. The method is based on the flow injection (Fl) technique. Total calcium is determined by atomic absorption spectrometry (AAS) (422.7 nm) and free calcium by spectrophotometry (580 nm). Interference in the determination of free calcium is eliminated by using a dialyser, which also separates the total and free calcium. Interference from phosphates in milk in the determination of total calcium by AAS is overcome by using a dinitrogen oxide-acetylene flame with the necessary suppression with K+. With 30-microliters samples the Fl system covers a standard working range of 100-1500 mg dm-3 of Ca2+. The system is suitable for the simultaneous determination of total calcium (relative standard deviation less than 1.30% for 1300-1500 mg dm-3 of total calcium) and free calcium (relative standard deviation less than 0.85% for 120-170 mg dm-3 of free calcium) in milk at a sampling frequency of about 60 samples h-1. The results obtained agree reasonably well with results from the AAS method.     

Tandem on-line dialysis with a double and single dialyser in flow injection dialysis — Simultaneous determination of calcium and high chloride in industrial effluents

The on-line double membrane dialyser described previously was coupled in series to a single dialyser in the manifold of a flow injection system to include the determination of samples with a high chloride content simultaneously with calcium in industrial effluents from a single sample injection. 50 μl of industrial effluent samples are injected into a carrier stream and are simultaneously dialysed in the double on-line dialyser for chloride and calcium. The dialysed chloride sample zones are further directed to a second dialyser that is incorporated in series with the first dialyser. This enables laboratories to determine samples with a very high chloride content up to 60 g/l simultaneously with calcium by using an automated tandem on-line dialysis technique. The fast and reliable fully automated two-component flow injection procedure operated at a sampling frequency of 90 samples per hour and the results obtained for chloride and calcium in industrial effluents compared well with those obtained by standard methods.     

Simultaneous flow injection analysis for two components with a double on-line dialyser

Summary An on-line double membrane dialyser was designed and incorporated into the manifold of a flow injection system for the simultaneous determination of more than one component in a single sample injection. A fast and reliable fully automated two-component flow injection procedure is described in which a single sample (50 l of industrial effluent water) is injected into a carrier stream and simultaneously dialysed for the determination of chloride and calcium. The results obtained for the chloride and calcium in industrial effluent water at a sampling rate of 90 per hour compared well with those obtained by standard methods.Dedicated to Professor Dr. Wilhelm Fresenius on the occasion of his 80th birthday     

Simultaneous flow injection determination of ammoniacal nitrogen and chloride in industrial effluent water with a combined on-line gas diffusion/dialyser unit

An on-line gas diffusion/dialyser unit has been designed and incorporated into the manifold of a flow injection system for the simultaneous determination of two different species in a single sample injected into the FIA system. A fast and reliable fully automated two-component flow injection procedure has been carried out where a single sample (50 l industrial effluent water) is injected into a carrier stream and simultaneously gas diffused and dialysed in a single on-line gas diffusion/dialyser unit for the determination of ammonia and chloride, respectively. The results obtained for the ammoniacal nitrogen and chloride in industrial effluent water compared well with data obtained by standard methods. The relative standard deviation for industrial effluent water samples with concentrations of ammoniacal nitrogen in the range between 0.050 and 1 g/l and chloride from 0.127 to 2.531 g/l have been better than 1.0% for ammoniacal nitrogen and 0.5% for chloride, respectively. The proposed system could be attractive for routine analyses of industrial effluent water.     

Indirect determination of bromide by diffusion flow injection analysis with amperometric detection

Summary A rapid, indirect diffusion flow injection analysis (FIA) method with amperometric detection has been developed for the selective and sensitive determination of Br^–. The method is based on permanganate oxidation of Br^– to bromine. Bromine diffuses through a PTFE membrane and is quantified amperometrically at a platinum working electrode. Calibration graphs were linear up to the maximum concentration of Br^– investigated (10.0 mmol/l). The precision of the technique was better than a relative standard deviation of 0.7% at 10.0 mol/l, with a throughput of 30 samples per hour. The effects of temperature, acidity, working potential, composition of the reagent solution and interferents on the FIA signals were studied. The catalytic effect of Cl^– on the permanganate oxidation of the analyte was utilized to lower the detection limit to 1 mol/l (16 ng Br^–). Similar detection limits were achieved by combining the effects of higher acidity (4.0 mol/l H₂SO₄) and elevated temperatures (40°C). The method was successfully applied to the determination of Br^– in chloride and other reagents, as well as in natural waters.     

Catalytic-fluorimetric determination of EDTA and iron(III) by flow injection analysis

Summary In this paper the authors report on several methods for the direct determination of EDTA and indirect determination of iron(III), based on the inhibition effect of EDTA on the catalytic action of copper (II) on the oxidation of 2,2-dipyridyl ketone hydrazone by hydrogen peroxide and on the decrease of this inhibition effect in the presence of Fe(III), respectively. These methods allow the determination of EDTA in the ranges of 0.4–2.0 g · ml^–1 and 0.2–1.0 g · ml^–1 for the normal and reversed FIA modes, respectively, and of 40–240 ng · ml^–1 for Fe(III) by reversed FIA.

---

Katalytisch-fluorimetrische Bestimmung von EDTA und Eisen(III) durch FließinjektionsanalyseInhibitionsmethoden

Zusammenfassung Verfahren zur direkten Bestimmung von EDTA sowie zur indirekten Bestimmung von Eisen(III) werden beschrieben. Sie beruhen auf der Inhibitorwirkung von EDTA auf den katalytischen Effekt von Kupfer(II) bei der Oxidation von 2,2-Dipyridylketonhydrazon mit Wasserstoffperoxid bzw. auf der Schwächung dieser Inhibitorwirkung in Gegenwart von Eisen(III). Es ist mit diesen Methoden möglich, EDTA im Bereich von 0,4–2,0 g/ml (normale FIA) bzw. 0,2–1,0 g/ml (umgekehrte FIA) und Eisen im Bereich von 40–240 ng/ml (umgekehrte FIA) zu bestimmen.

     

Flow injection flame atomic spectrometric determination of iron, calcium, magnesium, sodium and potassium in ceramic materials by using a variable-volume injector

Summary A series of different ceramic materials, such as porcelain, feldspar, kaolin, varnish, clay and stoneware have been analyzed. Iron, calcium and magnesium have been determined in these materials by flame atomic absorption and sodium and potassium by flame emission. The use of a variable-volume injector enables one to carry out these analyses in a flow system (after fusion of samples with lithium metaborate) and does not require different dilutions for the determination of each type of sample considered, nor the use of different flow injection manifolds. The developed procedure provides a limit of detection of 100 g/l for Na, 70 g/l for Ca, 50 g/l for both Fe and K and 8 g/l for Mg. The coefficient of variation obtained for the absorbance measurement is of the order of 0.5–2%. A series of 17 real samples were analyzed by the proposed procedure and the obtained results turned out to be comparable to those found by batch analysis.     

Selective determination of cobalt in a strongly acidic medium by flow injection analysis

Summary A selective method for the FIA spectrophotometric determination of Co(II) based on the use of pyridoxal 4-phenylthiosemicarbazone as reagent was developed with the aid of a straightforward 4-line flow injection manifold. The physical variables involved in the process were optimized as follows: injected sample volume 260 l; reactor lengths 116 and 150 cm. The proposed method allows the determination of cobalt over the concentration range 0.4–14.4 g ml^–1 at a sampling rate of 48 samples h^–1. The method is subject to very few interferences thanks to the fact that the strongly acidic medium used prevents the formation of most of the complexes of the reagent with other ions. It was applied to the determination of cobalt in steels.     

Direct determination of arsenic in sea water by electrothermal atomization atomic absorption spectrometry using D2 and Zeeman background correction

Arsenic in sea water was determined directly by graphite furnace atomic absorption spectrometry (GFAAS) using palladium nitrate as chemical modifier, at an optimum concentration of 15 mg l^–1. Deuterium and Zeeman effect background correction were compared and gave detection limits of 0.6 and 0.8 g l^–1, respectively. Precisions between 8 and 2%, for both correctors, were obtained with an injection volume of 40 l. The accuracy obtained with different reference materials: CRM-403 (1.461 g kg^–1), NASS-4 (1.26 ±0.09 gl^–1) and IAEA/W-4 (24–31 g l^–1) was studied for large injection volumes for both background correction systems. Interferences by chloride, sodium, potassium, calcium and silicon were removed by Zeeman correction, whereas deuterium correction was much less effective and was insufficiently accurate for sea water samples.     

Flow injection spectrophotometric determination of calcium, phosphate and chloride ions in milk.

Flow injection procedures for the determination of calcium, phosphate and chloride ions in milk samples are described. The reactions are based on the formation of coloured complexes and their spectrophotometric monitoring. A sample pre-treatment with acetate buffer was carried out owing to the complexity of the sample matrix. For chloride, a rapid and reliable automated procedure for direct measurement of its content in milk (using a dialyser to eliminate interferences) is also described. After optimizing the sample pre-treatment and flow injection variables, the procedures were applied to commercial milk; the results obtained agreed satisfactorily with those of the reference methods. With 50 mm3 samples, a working range of 0-15 ppm for calcium, 50-150 ppm for phosphate and 5-100 ppm for chloride is covered with a precision of better than 1.1%. The sample throughput was higher than 50 samples h-1. These preliminary experiments are the basis for the automation of the determination of calcium, phosphate and chloride ions using a computer-controlled, self-designed and laboratory-built autoanalyser.     

Voltammetric-enzymatic determination of ethanol in whole blood by flow injection analysis

Summary Two automatic methods are proposed for the voltammetric determination of ethanol in whole blood. They are based on the use of the enzymatic systems alcohol dehydrogenase/ nicotinamide adenine dinucleotide (method A) and alcohol dehydrogenase/nicotinamide adenine dinucleotide/ diaphorase/2,6-dichlorophenolindophenol (method B). The determination ranges are 2.5–30.0 g/ml and 0.5–30.0 g/ml with sampling rates of 60 and 30 samples/h, respectively. The coefficients of variation are about ±4%.

---

Voltammetrisch-enzymatische Bestimmung von Ethanol in Vollblut durch Fließinjektionsanalyse

     

Spectrophotometric determination of Fe(III) with tiron in the presence of cationic surfactant and its application for the determination of iron in Al-alloys and Cu-based alloys

A sensitive Spectrophotometric method for the determination of iron with tiron and a cationic surfactant, cetylpyridinium chloride, at pH 5.6 is reported. The complex is extracted into a chloroform-propan-2-ol (41) mixture and shows maximum absorbance at 520 nm. Beer's law is obeyed in the range 1–14 g/ml with an average molar absorptivity of 15800 l mol^–1 cm^–1. The molar ratio as determined by Job's method for Fe:tiron:CPC is 143. Interferences by various ions are examined. Zr, Ti and Mo interfere heavily. The method is applied for the determination of iron in Al-based and Cu-based alloys, using appropriate masking agents.     

Flow injection on-line ultrasound-assisted extraction of iron in meat samples coupled to a flame atomic absorption spectrometric system

Iron was extracted on-line from solid meat samples by a simple and rapid continuous ultrasound-assisted extraction system (CUES). The CUES is connected to a flow injection manifold, which allows the on-line flame atomic absorption spectrometric determination of iron. A Plakett–Burman design was used for the optimisation of the CUES. The method achieved a total sampling frequency of 11 samples per hour with a relative standard deviation for the complete procedure of 0.4%. The detection limit was 0.6 g g^–1 (dry mass) for a sample amount of 30 mg. Accurate results were obtained by measuring the certified reference materials BCR-186 (pig kidney) and BCR-184 (bovine muscle). The analytical procedure was applied to different real meat samples with satisfactory results.     

Determination of some trace elements in high-purity aluminium, zinc and commercial steel by AAS after preconcentration on amberlite XAD-1180 resin

The determination of trace metals, e.g. Bi, Cd, Pb, in high-purity aluminium, zinc and commercial steel by flame or graphite furnace atomic absorption spectrometry following their preconcentrations as iodo complexes on XAD-1180 resin by means of a short column system is described. The recoveries are quantitative (95%). The relative standard deviations varies between 6% and 10%. The relative errors are less than 8% in a concentration range of 1 × 10^–3 –4 × 10^–5%. Detection limits for flame AAS and GFAAS were in the ranges of 0.002–0.110 g/ml and 0.0003–0.004 g/ml or in the ranges of 0.08–4.40 g/g and 0.012–0.16 g/g with respect to the solid samples, respectively.     

Simultaneous-fluorimetric methods for the determination of ammonia and urea by use of flow injection configurations with dual injection valves

Summary Two fluorimetric methods are proposed for the simultaneous determination of ammonia and urea based on the reaction of the former with o-phthalaldehyde/2-mercaptoethanol and on the use of a dual injection system in which the valves are coupled in series or in parallel. An enzymatic reactor converts urea into ammonia which is determined by the same reaction. These configurations provide very similar results with a linear determination range between 0.5 and 10.0 g ml^–1 and a sampling frequency of 60 h^–1. The proposed methods are very tolerant to foreign species commonly found in water, as shown by applying them to samples of different origins.     

Individual and sequential flow injection spectrophotometric determination of vanadium(V) and titanium(IV)

Summary Methods for the individual and sequential flow injection spectrophotometric determination of vanadium(V) and titanium(IV) are proposed, based on the formation of peroxo complexes. The detection limits are 1.0 × 10^–5 mol/l V (120 l) and 2.5 × 10^–6 mol/l Ti (80 l). A cation exchange resin mini-column is incorporated on-line into the vanadium manifold to remove the titanium complex and allow the vanadium to be determined selectively. A normal injection valve is used for the individual determinations, but it is modified for determination of V(V)/–Ti(IV) mixtures in order to introduce two samples sequentially into the reagent stream. One passes through a cation exchanger minicolumn, the other through an empty column, before reaching the detector. The former allows V alone to be measured, the latter V+Ti.

---

Individuelle und sequentielle spektralphotometrische Fließinjektionsbestimmung von Vanadium(V) und Titan(IV)

---

Dedicated to Prof. Dr. G. Tölg on the occasion of his 60th birthday     

Photometry in a continuous flow system

Summary Sulphate in various environmental samples was determined by measuring the optical absorbance upon reaction with the barium(II) dimethylsulphonazo(III) complex. The measurement took place in a flow-through system. Interferences from phosphate, metal ions and others were eliminated. The results of a turbidimetric measurement, a spectrophotometric measurement with thorin, an automatic titration and the proposed method are compared. The latter allows the determination of sulphate in the range of 1.4–60 mol·l^–1. The standard deviation is 0.3–0.6 mol·l^–1, depending on the type of sample (water) analysed. A determination takes 1.5min.

---

Photometric in einem DurchflußsystemBestimmung von Sulphat mit Dimethylsulfonazo(III) in Umweltmaterial mit Hilfe eines Durchflußsystems

Zusammenfassung Sulfat wurde in verschiedenen Umweltproben durch Messung der Extinktion nach Reaktion mit dem Barium(II)-dimethylsulfonazo(III)-komplex im Durchflußsystem bestimmt. Störungen von Phosphat, Metallionen, u.a. wurden beseitigt. Die Ergebnisse einer turbidimetrischen, einer photometrischen, einer automatischen Titration und der vorgeschlagenen Methode werden verglichen. Die Methode ermöglicht die Sulfatbestimmung im Bereich von 1,4–60 mol·l^–1. Die Standardabweichung beträgt 0,3–0,6 mol· l^–1 je nach Typ des Probematerials (Wasser). Eine Bestimmung erfordert 1,5min.

     

Spectrophotometric determination of mercury with 5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine by flow injection analysis

5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine (m-Cl-TPPS₄) was synthesized and used for the Spectrophotometric determination of mercury by flow injection analysis. A pseudo-first-order reaction kinetic mechanism was proposed with a rate constant of 0.8 min^–1 for Hg(II) withm-Cl-TPPS₄ in the presence of 8-hydroxyquinoline in a medium of 1.0M acetic acid and sodium acetate buffer solution (pH 6.22). In the optimum conditions of reaction temperature (85 ° C), stopped-flow time (60 s) and sampling volume (100 l), the method's relative standard deviation was 0.82% (n = 12) at 5.0 g ml^–1 mercury, with a linear range of 0–12.0 g ml^–1 and an analytical frequency of 60h^–1. The detection limit (3) was 0.025 g ml^–1. Interference studies showed that most metal ions co-existing with Hg²⁺ could be tolerated at 100-fold excess levels, but Zn²⁺, Cu²⁺ and Mn²⁺ needed to be masked. The method has been applied to the analysis of water samples with satisfactory results.     

Direct determination of trace amounts of arsenic in powdered biological samples by atomic absorption spectrometry using an inner miniature cup for solid sampling techniques

Summary A new easy solid sampling technique with atomic absorption spectrometry by using an inner miniature cup in conjunction with the cupped type furnace was proposed for the direct determination of arsenic in NBS, NIES standard materials and marine organisms. A mixture of 3 M sulfuric and 4 M nitric acid solution containing 60 g of nickel was successfully used as the matrix modifier for the powdered samples examined. Optimum experimental conditions were determined based upon detailed examinations for the trace amount determination of arsenic in these samples. Analytical sensitivity and accuracy of this method were compared to the arsine generation followed by atomic absorption or ICP emission spectrometry. The standard deviations for 7–15 ppm As were found to be 3–10%.

---

Direkte Bestimmung von Arsenspuren in pulverföraügen biologischen Proben durch AAS mit Hilfe eines im Ofen einsetzbaren Miniaturbechers für feste Proben

Zusammenfassung Zur direkten Arsenbestimmung in NBS und NIES-Referenzmaterialien sowie Meeresorganismen durch AAS wurde ein in einen entsprechenden Ofen einsetzbarer Minaturbecher verwendet. Als Matrixmodifikator wurde ein Gemisch von 3 M Schwefel- und 4 M Salpetersäure mit 60 g Ni benutzt. Die optimalen Bedingungen wurden durch detaillierte Untersuchungen gefunden. Empfindlichkeit und Genauigkeit des Verfahrens wurden mit der Methode der Arsinerzeugung mit nachfolgender AAS oder ICP-AES verglichen. Relative Standardabweichungen von 3–10% für 7–15 ppm As wurden gefunden.