半导体硫化锌纳米微粒的合成与表征

采用液相均沉淀法,用不同原料(采用不同硫源或金属离子螯合剂)从3个途径合成了不同粒径的半导体ZnS纳米粒子,并用透射电子显微镜、X射线粉末衍射仪对粒子进行表征.     

La（Oxin）3·3H2O纳米晶的一步固相化学合成及表征

在近室温条件和超声波作用下,通过固相化学反应一步合成了La（Oxin）3·3H2O（8-羟基喹啉镧）纳米晶。用X射线衍射及电子衍射法分析了固相产物的物相,用透射电子显微镜观测粒子的大小、形貌、粒径及粒径分布。结果表明,产物为颗粒大小均匀、平均粒径约为40nm的纳米晶,产率为95．9％。改变反应物、反应物配比、掺人惰性物质、加入微量溶剂或表面活性剂、研磨不同时间等固相反应条件对合成纳米晶的晶粒形貌、粒度和粒径分布有一定影响。合成的纳米晶材料具有操作方便、合成工艺简单、产率高、选择性好、粒径均匀、且粒度可控、污染少,同时又可以避免或减少液相中易出现的硬团聚现象等突出优点。     

纳米2,4-二羟基苯甲酸铅(Ⅱ)配合物的合成及其燃烧催化性能研究

采用液相分散沉淀法制备了纳米2,4-二羟基苯甲酸-Pb(Ⅱ)配合物粉体,并用TG,XRD,TEM,IR和元素分析对产物进行了表征.研究了反应条件对产物粒径和粒子形貌的影响.用DSC考察了产物对吸收药热分解的催化作用.结果表明,在水溶液中得到的产物为15nm×40nm的棒状粒子,而在乙醇溶液中得到的是粒径约为50nm的球形粒子.产物对吸收药热分解有显著的催化效果,使吸收药的分解峰温降低5.6℃,分解热增加918J/g.     

乳液聚合法制备纳米金/聚苯乙烯复合粒子

以氯金酸为前驱体,十二烷基硫醇和硼氢化钠分别作为稳定剂和还原剂,采用相转移法制备了单分散的金纳米粒子.将金纳米粒子通过乳液聚合的方法制备了纳米金/聚苯乙烯复合粒子.通过紫外-可见吸收光谱(UV-Vis)研究了纳米金和纳米金/聚苯乙烯复合粒子的光吸收特性,使用傅立叶变换红外光谱(FT-IR)、X射线衍射(XRD)、透射电子显微镜(TEM)和动态光散射(DLS)对产物的组成、晶体结构、形貌、以及粒径进行了表征.结果表明,复合粒子为粒径分布较窄的球形,其中的金纳米粒子为面心立方结构.热失重分析(TGA)说明制备的纳米金/聚苯乙烯复合粒子具有很好的热稳定性.     

纳米Pb(II)-没食子酸配合物的合成及其燃烧催化性能

采用液相分散沉淀法制备了纳米 Pb(II)-没食子酸配合物粉体. 用热重分析(TG)、X 射线衍射仪(XRD)、透射电镜(TEM)、核磁共振仪(1H NMR)、红外光谱仪(IR)、激光散射粒径分析仪和元素分析仪对样品的物相、形貌、粒径和组成进行了表征. 研究了没食子酸的浓度和分散剂用量对产物的粒子大小的影响. 并测试了产物对推进剂燃烧的催化作用. 结果表明: 产物的平均粒径约为 30 nm. 没食子酸的浓度降低和分散剂用量增加均使产物的粒子减小. 产物能明显改善推进剂的燃烧性能, 使推进剂的燃速提高 88%, 压强指数降低了 70%.     

纳米Pb(II)-没食子酸配合物的合成及其燃烧催化性能

采用液相分散沉淀法制备了纳米Pb(II)-没食子酸配合物粉体. 用热重分析(TG)、X射线衍射仪(XRD)、透射电镜(TEM)、核磁共振仪(¹H NMR)、红外光谱仪(IR)、激光散射粒径分析仪和元素分析仪对样品的物相、形貌、粒径和组成进行了表征. 研究了没食子酸的浓度和分散剂用量对产物的粒子大小的影响. 并测试了产物对推进剂燃烧的催化作用. 结果表明: 产物的平均粒径约为30 nm. 没食子酸的浓度降低和分散剂用量增加均使产物的粒子减小. 产物能明显改善推进剂的燃烧性能, 使推进剂的燃速提高88%, 压强指数降低了70%.     

微乳中纳米胶囊的复凝聚法制备

在O/W型APG微乳液模板上, 以明胶和阿拉伯树胶作为包裹材料, 用复凝聚的方法制备纳米胶囊, 对影响纳米胶囊的合成条件进行了分析. 用粒度仪测定产物的粒径及其分布, 用透射电镜观察产物的形貌. 结果表明, 用复凝聚法在微乳中合成了粒度均匀、粒径30～100 nm的球性纳米胶囊. 考察了微乳液的组成、高分子的浓度和复凝聚的条件对纳米胶囊性质的影响. 纳米胶囊对氯氰菊酯的包裹率较高, 在60%以上. 本方法条件温和, 操作简单, 是一种新型的纳米胶囊合成技术.     

金纳米粒子的共振散射光谱

采用Frens 法制备了粒径为10～95 nm的金纳米粒子.它们均在580 nm处产生一个共振散射峰.从液相纳米粒子的波动观点出发,解释了金纳米粒子共振散射光谱的产生原因.用超分子界面能带理论解释了金纳米粒子的颜色与粒径的关系.根据最大吸收波长与粒径的关系,建立了一种测量金纳米粒子粒径的光度标尺.     

二苯胺磺酸钠还原法制备粒径可控的金纳米粒子

采用二苯胺磺酸钠还原四氯合金酸的方法,在室温条件下,用SDS(十二烷基硫酸钠)、SDBS(十二烷基苯磺酸钠)作表面活性剂,成功地合成了金纳米粒子.分别讨论了还原剂二苯胺磺酸钠、表面活性剂(SDS、SDBS)及四氯台金酸的浓度等对金纳米粒子的粒径和形貌的影响.通过控制反应条件,可以合成出平均粒径大约为10、14、30、36nm的金纳米粒子.利用透射电镜(TEN)、紫外-可见(UV-Vis)吸收光谱对金纳米粒子进行了表征.研究结果表明不同的SDS或SDBS/HAuCl4的摩尔比,对金纳米粒子的尺寸大小有影响.     

纳米MnO2的固相合成及其电化学性能的研究(Ⅰ) --纳米γ-MnO2的合成及表征

用醋酸锰分别与柠檬酸、草酸和8-羟基喹啉在室温及低温下发生固相反应生成锰配合物,经热分解和酸处理等手段最终制备出纳米γ-MnO2.用元素分析、化学分析、X射线衍射、热重/差热分析和透射电镜等测试手段对固相反应的可行性作了讨论,并对合成的样品进行了表征.从TEM照片上看,产物粒子呈球形,粒径多为20～30 nm.酸处理可大大提高样品的氧化度,但酸化过程中粒子出现团聚现象,粒子形貌也有所改变,似有取向生长的趋势.文中还讨论了低温条件下利用固相反应制备纳米材料的原因.     

A novel one step synthesis of silver nanoparticles using room temperature ionic liquid and their biocidal activity

This article reports the synthesis of silver Nan particles (SNPs) using 1-(dodecyl) 2 amino-pyridinium bromide ionic liquid. This is a new one phase method for the synthesis of uniform monodispersed crystalline silver nanoparticles in a water-ionic liquid system. In this work, the functionalized room temperature IL acts as stabilizing agent and solvent. Hydrazine hydrate acts as reducing agent. To the best of our knowledge, there is no report of the synthesis of metal nanoparticles using this ionic liquid. The synthesis of silver nanoparticles is very primarily studied by UV-Visible spectroscopic analysis. The TEM and particle size distribution was used to study morphology and size of the particles. The charge on synthesized SNPs was determined by Zeta potential. The silver nanoparticles have been known to have inhibitory and bactericidal effect. The investigation of antibacterial activities of ionic liquid stabilized silver nanoparticles was performed by measurement of the minimum inhibitory concentration.     

Novel approach for electrochemical preparation of sulfur nanoparticles

An electrochemical method is presented for the preparation of sulfur nanoparticles (S-NPs) from thiosulfate ion. The particle size of the S-NPs can be adjusted between 35 and 65 nm by varying parameters such as the initial concentration of thiosulfate. The solvent/non-solvent precipitation method was also applied to the preparation of S-NPs for comparison. In this case, the use of hot alcohol and cold water as solvent/non-solvent system along with 100 ml·min^?1 flow rate for co-mixing of non-solvent resulted in the formation of S-NPs in a typical size of 250 nm that are fairly homogeneous in shape and have a narrow particle size distribution. The results revealed that, in comparison to the precipitation process, the electro-synthetic method offers simplicity, higher efficiency, improved size control, and less environmental contamination.

A new and simple method for sulfur nanoparticles synthesis

Sulfur nanoparticles were successfully synthesized via novel water-in-oil microemulsion system. The microemulsion system contained cyclohexane as an oil phase, Triton X-100 as a surfactant, butanol as a co-surfactant and sodium polysulfide solution or hydrochloric acid solution as aqueous phase, respectively. The sulfur nanoparticles were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and Fourier transform infrared spectroscopy. The results showed that the as-prepared monoclinic sulfur nanoparticles exhibited high purity and spherical shape with an average size of about 22 nm.     

以无机硫为原料制备硫化铅量子点及其表征

根据高温下快速成核低温下慢速生长的量子点制备原理, 采用胶体化学的方法成功制备了不同粒径的硫化铅半导体量子点. 这种方法的特点是以无味和低毒的硫化钠作为制备硫化铅量子点硫的前驱物, 因此这是一种量子点的绿色化学合成方法. 油酸作为稳定剂控制硫化铅的粒径. 采用X射线衍射和高分辨透射电镜表征了量子点的晶体结构、形貌和粒径, 采用可见-近红外吸收光谱研究了硫化铅量子点的量子尺寸效应. 通过降低油酸的添加量可以促进量子点的生长, 得到较大粒径量子点. 并探讨了量子点的生长机理.     

Size control synthesis of sulfur doped titanium dioxide （anatase） nanoparticles, its optical property and its photo catalytic reactivity for CO2 ＋ H2O conversion and phenol degradation

Sulfur doped anatase TiO2 nanoparticles (3 nm−12 nm) were synthesized by the reaction of titanium tetrachloride, water and sulfuric acid with addition of 3M NaOH at room temperature. The electro-optical and photocatalytic properties of the synthesized sulfur doped TiO2 nanoparticles were studied along with Degussa commercial TiO2 particles (24 nm). The results show that band gap of TiO2 particles decreases from 3.31 to 3.25 eV and for that of commercial TiO2 to 3.2 eV when the particle sizes increased from 3 nm to 12 nm with increase in sulfur doping. The results of the photocatalytic activity under UV and sun radiation show maximum phenol conversion at the particle size of 4 nm at 4.80% S-doping. Similar results are obtained using UV energy for both phenol conversion and conversion of CO2+H2O in which formation of methanol, ethanol and proponal is observed. Production of methanol is also achieved on samples with a particle size of 8 and 12 nm and sulfur doping of 4.80% and 5.26%. For TiO2 particle of 4 nm without S doping, the production of methanol, ethanol and proponal was lower as compared to the S-doped particles. This is attributed to the combined electronic effect and band gap change, S dopant, specific surface area and the light source used.     

Spherical Zinc Oxide Nano Particles from Zinc Acetate in the Precipitation Method

The liquid precipitation method using zinc acetate dihydrate was applied for the synthesis of uniform and spherical ZnO nanoparticles. The ultrafine zinc oxid was prepared in a water‐ethanol mixture solution. The solution containing zinc cation was soluble in water. The surface‐active agent triethanolamine (TEA) was soluble in ethanol. Then alkali precipitated by adding n‐propylamine. The spherical zinc oxide particle morphology was found to be highly dependent on the zinc salt concentration, ethanol‐water ratio, and the surface‐active agent additive. The process can produce white ZnO powder of 50–90 nm in size. The morphology of zinc oxide showed a powder shape by transmission electron microscopy (TEM), the crystallization phase structure of zinc oxide by X‐ray diffraction (XRD), and the zinc oxide remaining by using an organic analysis by infrared spectroscopy (IR).     

Synthesis of highly stable silver nanoparticles by photoreduction and their size fractionation by phase transfer method

In this report we demonstrate a green chemical approach for the synthesis of stable silver nanoparticles in aqueous medium using tyrosine as an efficient photoreducing agent. A narrow size distribution of silver nanoparticles can be achieved by this simple photoirradiation method without using any additional stabilizing agents or surfactants. Two different irradiation sources have been explored resulting in a different particle size distribution pattern in each case. Further, we show that starting from a polydisperse tyrosine synthesized silver nanoparticles sample, it is also possible to fractionate them into different size ranges. The size fractionation was achieved by a 2 stage phase transfer method employing different organic solvents. The nanoparticles synthesized were characterized using UV-vis spectroscopy, Transmission electron microscopy (TEM) and X-ray diffraction (XRD) techniques.     

Synthesis, characterization and optical band gap of NiO nanoparticles derived from anthranilic acid precursors via a thermal decomposition route

This study focuses on the preparation and characterization of single phase NiO nano particles. Four nickel anthranilic acid complexes were synthesized by the semi-solid phase reaction method as precursors for the preparation of NiO nanoparticles via a solid-state decomposition procedure at 700 °C. Thermogravimetric analysis (TGA) was applied to determine the thermal behavior of the precursors and the temperature at which the precursors decompose leaving the oxide. The crystalline structures of the products were investigated by X-ray diffraction (XRD), the morphology of particles by SEM and TEM. The particles size was determined by STM, and the average particle size was found to be 8 nm. Electronic spectra were used to clarify qualitatively the change in absorption band positions on changing the particle size of NiO. The optical band gap of the NiO nanoparticles was calculated and indicated a direct transition. The values of the optical band gap of NiO nanoparticles increase as the particle size decreases.     

锂硫电池正极用硫/介孔碳复合材料的制备及电化学性能

制备了以十二烷基硫酸钠(SDS)为模板的介孔碳,并将介孔碳和单质硫采用熔融渗透法复合制得硫/介孔碳复合材料。SEM、TEM和BET结果显示介孔碳成直径约为500 nm的大小均一的球体,存在孔径为2 nm的微孔;单质硫充分填充在介孔碳的微孔中。以硫/介孔碳复合物作为锂硫电池正极材料时显示出高的电化学性能。初始放电容量高达1519 mAh·g^-1,在200 mA·g^-1的电流密度下充放电200个循环后依然能保持在835 mAh·g^-1。硫/介孔碳复合材料的高倍率性能和优异的循环稳定性,源于介孔碳良好的导电性及其孔结构的固硫作用。     

Combustion synthesis of calcium doped ZnO nanoparticles for the photocatalytic degradation of methylene blue dye

ZnO nanoparticles are one of the prominent photocatalysts for environmental applications due to its high redox ability, nontoxic and higher stability. This report explains the synthesis of ZnO nanoparticles by a simple solution combustion method using zinc nitrate hexahydrate as an oxidizing agent and incense stick powder as fuel at 400 °C. Several techniques were adopted for the characterization of the obtained product. X-ray diffraction (XRD) pattern shows that a lower concentration of fuel gives pure ZnO and a higher concentration of fuel results in calcium doped ZnO with a cubic phase having a crystallite size of 32–28 nm. UV–vis spectrum shows that as the fuel concentration increases, band gap decreases and reaches to 3.33 eV for 3 g of fuel. Spongy networks with many pores wereobserved in the scanning electron microscope (SEM) and transmission electron microscope (TEM) images showed the average particle size of Ca doped ZnO NPs is about 20 nm. Pure and Ca doped ZnO nanoparticles were examined for photocatalytic degradation of methylene blue (MB) dye under UV light irradiation. The results prove that Ca doped ZnO nanoparticles show good photocatalytic activity.