Recombination luminescence of poly(arylene phthalide) films induced by visible light

Long-term afterglow emission (AG) of poly(arylene phthalide) films (PAP) irradiated with visible light has been discovered. Recombination nature of the AG was experimentally proven as in the case of UV irradiation. Features of the observed AG spectra were analyzed in comparison with the photo-, electro-, and thermoluminescence spectra of the PAP films in relation to the commonness of the AG generation mechanism, which is associated with the involvement of the two-photon reactions and triplet states in the photoprocesses in PAP.     

Voltammetric determination of bisoprolol on a glassy carbon electrode modified by poly(arylene phthalide)

New voltammetric sensors based on glassy carbon electrodes (GCEs) modified by poly(arylene phthalide) are studied. The electrochemical behavior of bisoprolol on GCEs modified by poly(arylene phthalide) is investigated. The effects of potential scan rate, time of accumulation on the electrode, pH of supporting electrolyte, and concentration on the current of bisoprolol electrooxidation are estimated. A procedure is developed for the voltammetric determination of bisoprolol on glassy carbon electrodes modified by poly(arylene phthalide). The dependence of the analytical signal on the concentration of bisoprolol is linear in the range 10^–6–10^–5 M with the limit of detection (3.4–9.8) × 10^–8 M.     

Recombination luminescence of poly(arylene phthalide) films: 2. Afterglow emission induced by electric excitation in poly(arylene phthalide) films

Absorption, luminescence and electroluminescence spectra of films of the unconjugated copolymer poly(arylene ether ketone) (CPAEK) were measured. Long-lasting afterglow emission was observed resulting from electro- and photoexcitation of the CPAEK films. and is possible mechanisms of generation are discussed.     

Electroluminescence in unconjugated polymers based on poly(arylene phthalide) films

We discuss the results of measurements of the optical characteristics of thin organic films of unconjugated poly(arylene ether ketone) polymer. We have observed persistent electroluminescence for this polymer. We have established an interrelationship between the polarity of the voltage applied to the experimental structure and the electroluminescence spectrum. Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 45, No. 1, pp. 42–45, January–February, 2009.     

Synthesis and electrical conductivity of poly(arylene vinylene). I. Poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene)

The highly conjugated aromatic polymers, poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene), were obtained from their water soluble, sulfonium salt precursor polymers. Films of these polymers were reacted with either AsF₅ or I₂ vapor. Poly(2,5-dimethoxyphenylene vinylene) showed increases in electrical conductivity of up to 14 to 15 orders of magnitude for these two dopants, while an 8 to 9 order of magnitude increase was observed for poly(2,5-dimethylphenylene vinylene) with the same dopants. The synthesis of the precursor polymers, the properties and elimination reactions of films of the precursors, the doping reactions, and the conductivities of the resulting phenylene vinylene films are discussed.     

Synthesis of thermally crosslinkable fluorine‐containing poly(arylene ether ketone)s—II. Propargyl ether terminated poly(arylene ether ketone)s

Novel thermally crosslinkable fluorine‐containing poly(arylene ether ketone)s comprised of 2,3,5, 6‐tetrafluoro‐1,4‐phenylene moiety were synthesized by the termination of polymer chain ends with propargyl ether groups in order to improve solvent resistance. Crosslinking reaction occurred over 250°C through the formation of both chromen ring and polyene structure. This structure change brought about not only the outstanding solvent resistance but also the increase in glass transition temperature (T_g). The cured films also exhibited excellent thermal stability, transparency and hydrophobicity derived from fluorine atoms. Copyright © 2004 John Wiley & Sons, Ltd.     

Thermally stable sulfone-containing poly(amide-imides)

Novel sulfone containing poly(amide-imides) have been prepared by reacting 3,4-dicarboxy-4′-(chloroformyl)-diphenylsulfone dianhydride with various aromatic diamines. Relatively high molecular weight polymers were obtained by using a two-step procedure. Transparent poly(amide-imide) films, varying in color from dark yellow to colorless, were formed by thermally treating polyamic acid solutions. All films showed good thermal stability.     

New synthetic routes to poly(isothianaphthene). II. Mechanistic aspects of the reactions of phthalic anhydride and phthalide with phosphorus pentasulfide

The results of some mechanistic studies on the formation of poly(isothianaphthene) from phthalic anhydride and phthalide by reaction with phosphorus pentasulfide (P₄S₁₀) are described. Based on the observed intermediates during the polymerization and their reactivity, it is proposed that both reactions occur by a sequence of substitution (thionation), isomerization, and polymerization reactions. P₄S₁₀ is the most efficient reagent for the conversion of phthalic anhydride and phthalide, and Lawesson's Reagent (a commonly used thionating reagent) gives less satisfactory results. It is suggested that P₄S₁₀ assists the rate-determining step. Oxygen-containing monomers do not polymerize in the absence of a thionating reagent under the conditions for the synthesis of PITN, thereby keeping the incorporation of oxygen into the polymeric backbone to a minimum. © 1996 John Wiley & Sons, Inc.     

Novel organosoluble and colorless poly(ether imide)s based on 3,3‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]phthalide dianhydride and aromatic bis(ether amine)s bearing pendent trifluoromethyl groups

A novel series of colorless and highly organosoluble poly(ether imide)s were prepared from 3,3‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]phthalide dianhydride with various fluorinated aromatic bis(ether amine)s via a conventional two‐stage process that included ring‐opening polyaddition to form the poly(amic acid)s followed by cyclodehydration to produce the polymer films. The poly(ether imide)s showed excellent solubility, with most of them dissoluble at a concentration of 10 wt % in amide polar solvents, in ether‐type solvents, and even in chlorinated solvents. Their films had a cutoff wavelength between 358 and 373 nm, and the yellowness index ranged from 3.1 to 9.5. The glass‐transition temperatures of the poly(ether imide) series were recorded between 237 and 297 °C, the decomposition temperatures at 10% weight loss were all above 494 °C, and the residue was more than 54% at 800 °C in nitrogen. These films showed high tensile strength and also were characterized by higher solubility, lighter color, and lower dielectric constants and moisture absorption than an analogous nonfluorinated polyimide series. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3140–3152, 2006     

Fluorinated poly(arylene ether ketone)s bearing pentafluorostyrene moieties prepared by a modified polycondensation

The polycondensation of decafluorobenzophenone with hexafluorobisphenol A was modified by the addition of a molecular sieve dehydrating apparatus to the refluxing reaction system. This modification promoted the polymerization and enabled the reactions to be conducted in milder conditions and completed in a shorter time, thereby depressing side reactions such as branching and crosslinking. The resulting fluorinated poly(arylene ether ketone)s (FPAEK) were free of gel particles and possessed the designed molecular weights. This modified procedure was also suitable for introducing crosslinkable pentafluorostyrene (FSt) moieties into the polymers at the chain ends and/or inside the chain with the vinyl group of FSt being pendant. The resulting FSt containing fluorinated poly(arylene ether ketone)s (FPAEK‐FSt) can then be thermally crosslinked at 100 °C in the presence of 1% benzoyl peroxide (BPO) or at 250 °C without any initiator. The glass‐transition temperatures (T_g's) of FPAEK increased with increasing molecular weight and leveled off at about 147 °C for the polymer with a number‐average molecular weight of 18,600 Da, whereas the values were not apparently affected by the addition of FSt units. However, crosslinking of the FPAEK‐FSt resulted in an approximate 30 °C increase of the T_g. Spin‐coating FPAEK‐FSt onto silicon wafers followed by crosslinking gave films with excellent thermal stability, physical strength, and adhesion to the substrate as well as good reproducibility in terms of film preparation and optical properties. The refractive index and birefringence of the films measured at a wavelength of 1.55 μm were 1.502 and 2.5 × 10^?3, respectively. © 2002 Government of Canada. Exclusive worldwide publication rights in the article have been transferred to Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4205–4216, 2002     

Synthesis and properties of new organo‐soluble and strictly alternating aromatic poly(ester‐imide)s from 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide and bisphenols

A series of new strictly alternating aromatic poly(ester‐imide)s having inherent viscosities of 0.20–0.98 dL/g was synthesized by the diphenylchlorophosphate (DPCP) activated direct polycondensation of the preformed imide ring‐containing diacid, 3,3‐bis[4‐(trimellitimidophenoxy)phenyl]phthalide (I), with various bisphenols in a medium consisting of pyridine and lithium chloride. The diimide–diacid I was prepared from the condensation of 3,3‐bis[4‐(4‐aminophenoxy)phenyl]phthalide and trimellitic anhydride. Most of the resulting polymers showed an amorphous nature and were readily soluble in a variety of organic solvents such as N‐methyl‐2‐pyrrolidone (NMP) and N,N‐dimethylacetamide (DMAc). Transparent and flexible films of these polymers could be cast from their DMAc solutions. The cast films had tensile strengths ranging 66–105 MPa, elongations at break from 7–10%, and initial moduli from 1.9–2.4 GPa. The glass‐transition temperatures of these polymers were recorded between 208–275 °C. All polymers showed no significant weight loss below 400 °C in the air or in nitrogen, and the decomposition temperatures at 10% weight loss all occurred above 460 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1090–1099, 2000     

Ferroelectric behavior and structural change of poly(trimethylene terephthalate) induced by external electric field

The ferroelectric behavior and structural change induced by the external electric field were observed for poly(trimethylene terephthalate) (PTT), which has nonpolar crystalline structure with carbonyl groups aligned antiparallel to each other. The displacement‐electric field hysteresis curves of PTT films showed hysteresis above 140 °C, which indicated the polarization reversal of PTT. The pyroelectric constant and thermally stimulated depolarization current suggest the depolarization of the polar structure of PTT induced by the external electric field above 150 °C. An endothermic peak caused by the depolarization was also observed in the differential scanning calorimetry for the PTT film poled at 30 MV/m. The change of the crystalline structure and the orientation of carbonyl groups induced by the electric filed were investigated by X‐ray diffraction patterns and infrared spectra. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1991–1996, 2009     

Synthesis and properties of novel poly(arylene ether)s and poly(arylene thioether)s based on a pyridazine biphenol or a phthalazine biphenol

Novel sulfur‐containing biphenol monomers were prepared in high yields by the reaction of 4‐mercaptophenol with chloropyridazine or chlorophthalazine compounds. High‐molecular‐weight poly(arylene ether)s were synthesized by a nucleophilic substitution reaction between these sulfur‐containing monomers and activated difluoro aromatic compounds. The inherent viscosities of these polymers ranged from 0.34 to 0.93 dL/g. The poly(pyridazine)s exhibited glass‐transition temperatures greater than 165 °C. The poly(phthalazine)s showed higher glass‐transition temperatures than the poly(pyridazine)s. A polymer synthesized from a bisphthalazinebiphenol and bis(4‐fluorophenyl)sulfone had the highest glass‐transition temperature (240 °C). The thermal stabilities of the poly(pyridazine)s and poly(phthalazine)s showed similar patterns of decomposition, with no significant weight loss below 390 °C. The poly(phthalazine)s were soluble in chlorinated solvents such as chloroform, and the poly(pyridazine)s were soluble in dipolar aprotic solvents such as N,N′‐dimethylacetamide. The soluble poly(pyridazine)s and poly(phthalazine)s could be cast into flexible films from solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 262–268, 2007     

Compatibility of binary systems of poly(methyl methacrylate), poly(vinyl chloride) and poly(vinyl acetate)

The influence of the thermal treatment on the stability in time of the dispersion degree of films containing binary polymer mixtures, poly(vinyl chloride)/poly(methyl methacrylate), poly(vinyl chloride)/poly(vinyl acetate) and poly(vinyl acetate)/poly(methyl methacrylate), was studied by thermogravimetry and optical microscopy with phase contrast. The dispersion degree depends particularly on the composition of the polymer mixture and can be improved by thermal treatment at temperatures above the glass temperatures of both homopolymers. It seems that this thermal treatment yields exclusively metastable structures with a general tendency to phase separation in a short time after thermal treatment, the heterogeneity mixtures (as film) being more pronounced.     

Study of charge storage in the nanofibrous poly(ethylene terephthalate) electrets prepared by electrospinning or by corona discharge method

In this paper, the charge storage performance of electrospun poly(ethylene terephthalate) (PET) mats with high specific surface area was evaluated in comparison to that of PET film electrets. Corona discharge method was used to charge the electrospun PET mats and PET films. The surface potential decay measurements revealed that the corona charged РЕТ mats had higher initial values for the normalized surface potential compared to the РЕТ electret films. A tendency for stabilization of the electret charge to one and the same value for all charged samples (mats and films) after the 50th day was observed. The peaks at 90 °C in the thermally stimulated current (TSC) spectra of uncharged and charged in corona discharge electrospun PET mats were observed and attributed to a relaxation of the separated space charges, the dipole disorientation or injected charges within the bulk. It was found that the value of the storage charge in a corona charged electrospun PET mats was higher than that in PET mats prepared by electrospinning.     

Direct copolymerization of sulfonated poly(phthalazinone arylene ether)s for proton‐exchange‐membrane materials

Sulfonated poly(phthalazinone ether ketone) (SPPEK) copolymers and sulfonated poly(phthalazinone ether sulfone) (SPPES) copolymers containing pendant sodium sulfonate groups were prepared by direct copolymerization. The reaction of disodium 3,3′‐disulfonate‐4,4′‐difluorobenzophenone (SDFB‐Na), 4,4′‐difluorobenzophenone (DFB), and 4‐(4‐hydroxyphenyl)‐1(2H)‐phthalazinone (DHPZ) at 170 °C in N‐methyl‐2‐pyrrolidione containing anhydrous potassium carbonate gave SPPEKs. SPPESs were similarly obtained with 3,3′‐disulfonate‐4,4′‐difluorophenyl sulfone, 4‐fluorophenyl sulfone (DFS), and DHPZ as monomers. The sulfonic acid groups, being on deactivated positions of the polymer backbone, were expected to be hydrolytically more stable than postsulfonated polymers. Fourier transform infrared and ¹H NMR were used to characterize the structures and degrees of sulfonation of the sulfonated polymers. Membrane films of SPPEKs with SDFB‐Na/DFB molar feed ratios of up to 60/40 and SPPESs with sulfonated 4‐fluorophenyl sulfone/DFS molar feed ratios of up to 50/50 were cast from N,N‐dimethylacetamide polymer solutions. Membrane films in acid form were then obtained by the treatment of the sodium‐form membrane films in 2 N sulfuric acid at room temperature. An increase in the number of sulfonate groups in the copolymers resulted in an increased glass‐transition temperature and enhanced membrane hydrophilicity. The sodium‐form copolymers were thermally more stable than their acid forms. The proton conductivities of the acid‐form copolymers with sulfonated monomer/unsulfonated monomer molar feed ratios of 0.5 and 0.6 were higher than 10^?2 S/cm and increased with temperature; they were less temperature‐dependent than those of the postsulfonated products. SPPESH‐50 showed higher conductivity than the corresponding postsulfonated poly(phthalazinone ether sulfone). © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2731–2742, 2003     

Crosslinkable fluorinated poly(arylene ethers) bearing phenyl ethynyl moiety for low-loss polymer optical waveguide devices

Crosslinkable fluorinated poly(arylene ethers) (FPAE-Fn-PEP) with high transparency and high thermal stability have been investigated for low-loss optical waveguide materials. FPAE-Fn-PEP bearing phenyl ethynyl moiety at the polymer chain end were synthesized by the reaction of 4,4′-(hexafluoro-isopropylidene)diphenol with an excess decafluorobiphenyl, followed by the reaction of 4-phenyl ethynyl phenol. The M_ns and M_w/M_ns of the polymers determined by GPC with polystyrene standard were in the range of 6200 to 19,400 and 1.4 to 2.04, respectively. The resulting polymers were thermally crosslinked at 320°C for 2 h. The cured polymers show good chemical resistance and high thermal stability up to 510°C under nitrogen. The refractive indices of their films were controlled between 1.495 and 1.530 at 1.55 μm by adjusting molecular weight. A single-mode channel waveguide made of FPAE-F20-PEP was fabricated by conventional photolithography and O₂ reactive ion etching (RIE). The propagation loss of the channel waveguide was measured and found to be less than 0.2 dB/cm at 1.55 μm. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2881–2887, 1998     

Phthalide as an activating group for the synthesis of poly(aryl ether phthalide)s by nucleophilic aromatic substitution

The phthalide ring was examined as an activating group for nucleophilic aromatic substitution. The proposed mechanism by which activation occurs is through a ring opening of the phthalide ring to form a Meisenheimer‐like σ complex. 3,3‐Bis(4‐fluorophenyl)phthalide was synthesized and examined under different reaction conditions to determine its suitability for polymer formation. Semiempirical calculations at the PM3 level suggested that 3,3‐bis(4‐fluorophenyl)phthalide is only moderately activated, whereas ¹H, ¹³C, and ¹⁹F NMR spectroscopy suggested that the monomer was not sufficiently activated for nucleophilic aromatic substitution. However, low‐molecular‐weight polymers (number‐average molecular weight < 7000 g/mol) were produced from bisphenol A, hydroquinone, and phenolphthalein. The polymers were characterized by gel permeation chromatography, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, NMR spectroscopy, and differential scanning calorimetry. The polymers displayed relatively high glass‐transition temperatures. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3046–3054, 2002     

Structure and properties of nanocomposites based on poly(arylene ether ketones) and metalalkoxysiloxanes

Nanocomposites obtained by in situ filling from amorphous poly(arylene ether ketones) based on 4,4´-difluorobenzophenone and 3,3-bis(4´-hydroxyphenyl)phthalide (phenolphthalein) with hydroxyl or benzophenone end groups were investigated. Metalalkoxysiloxanes, namely tris-(diethoxymethylsiloxy)iron, tetrakis-(diethoxymethylsiloxy)zirconium, and tetrakis- (diethoxymethylsiloxy)hafnium were used as precursors of the inorganic phase. It is shown that the morphology of the inorganic phase of nanocomposites can be varied from dispersed particles to a continuous network only by changing the type of the central metal atom of the metalalkoxysiloxane with the same organosilicon “framing”. The concentration of the precursor influences mainly the size of the filler particles. An application of tris-(diethoxymethylsiloxy)iron at a concentration of less than 14 wt.% makes it possible to obtain in situ filled polymers with a higher glass transition temperature than the ones obtained using tetrakis-(diethoxymethylsiloxy)zirconium or tetrakis-(diethoxymethylsiloxy)hafnium.     

Thermal and environmental stability of poly(4-ethynyl-p-xylylene-co-p-xylylene) thin films

The aim of this paper was to test the thermal and environmental stability of poly(4-ethynyl-p-xylyleneco-p-xylylene) thin films prepared by chemical vapor deposition(CVD) and to optimize the reaction conditions of the polymer.Fourier transformed infrared spectroscopy(FTIR),thermogravimetric analysis(TGA) and fluorescence microscopy were employed to investigate the stability of the reactive polymer coatings in various environmental conditions.Chemical reactivity of the thin films were then tested by Huisgen 1,3-dipolar cycloaddition reaction(‘‘click' reaction).The alkyne functional groups on poly(4-ethynyl-p-xylylene-co-p-xylylene) thin films were found to be stable under ambient storage conditions and thermally stable up to 100 8C when annealed at 0.08 Torr in argon.We also optimized the click reaction conditions of azide-functionalized molecules with poly(4-ethynyl-p-xylylene-co-p-xylylene).The best reaction result was achieved,when copper concentration was 0.5 mmol/L,sodium ascorbate concentration to copper concentration was 5:1.In contrast,the azide concentration and temperature had no obvious effect on the surface reaction.