Stripping Voltammetry at Microdisk Electrode Arrays: Theory

Anodic stripping voltammetry (ASV) is an extremely powerful tool for detection of metal ions in solution through a two step process of preconcentration of the metal at the electrode surface, followed by electrodissolution. The second phase produces an electroanalytical response proportional to the amount of material deposited in the first phase. This paper utilizes theory to explore the electrochemical signals produced when considering ASV at a microelectrode or ultramicroelectrode arrays. The theory outlined is applicable mostly to thin mercury film absorption and metal adsorption.     

Application of thin-shielded mercury microelectrodes in anodic stripping voltammetry

The performance in anodic stripping voltammetry (ASV) of hemispherical mercury microelectrodes, fabricated by electrodeposition of liquid mercury on the surface of Pt microdisks which were surrounded by a rather thick or thin insulating shield, was compared. The Pt microdisks were produced by sealing a wire of 25 μm diameter into a glass capillary, and by coating the cylindrical length of the Pt wire with a cathodic electrophoretic paint. The ratio of the overall tip radius b, to the basal radius of the electrode a, so-called RG = b/a, was equal to 110 ± 10 and 1.52 ± 0.01 for the thick- and thin-shielded microdisk, respectively. The mercury microelectrodes were characterized by cyclic voltammetry at 1 mV s⁻¹, in 1 mM Ru(NH₃)₆³⁺ aqueous solution. The steady-state voltammogram recorded with the thin-shielded mercury microelectrode displayed less hysteresis, while the steady-state current was about 30% higher than that of the thicker one. This was a consequence of the additional flux due to diffusion from behind the plane of the electrode. The flux enhancement, which was operative at the thin-shielded mercury microelectrode during the deposition step in the ASV experiments, allowed recording stripping peaks for Cd and Pb, which resulted about 32% larger than those recorded at the thicker shielded mercury microelectrode, under same experimental conditions.The usefulness of the thin-shielded mercury microelectrode for ASV measurements in real samples was verified by determining the content of heavy metal ions released in the pore water (pH 4.5) of a soil slurry.     

Mercury ions complexation with a series of heterocyclic derivatives of 3-hydroxychromone: spectral effects and prospects for ultrasensitive Hg2+ probing

Complexation of three 3-hydroxychromone derivatives bearing a nitrogen-containing heterocyclic moiety in the position 2 of the chromone bicycle - benzimidazole, quinoline, and 2,5-diphenyloxazole, with mercury(II) ions is reported. Formation of chelate complexes with the metal cations coordinated with the cavity formed by 3-OH and 4-C═O groups was shown, as well as the possibility of side moiety heteroatom participation in binding of metal ions. High sensitivity to mercury of 2,5-diphenyloxazole-substituted 3-hydroxychromone was elucidated, allowing to detect Hg(2+) below the maximum permissible concentration for drinking water. This makes the above-mentioned compound a prospective basis for development of sensors for ultralow mercury concentration detection in water. Unusual fluorescence ignition of 2-(quinolin-2-yl)-3-hydroxychromone at low Hg(2+) concentrations, rarely observed for heavy metals ions complexation with organic fluorescent ligands, was discussed.     

Selective detection of mercury (II) ion using nonlinear optical properties of gold nanoparticles

Contamination of the environment with heavy metal ions has been an important concern throughout the world for decades. Driven by the need to detect trace amounts of mercury in environmental samples, this article demonstrates for the first time that nonlinear optical (NLO) properties of MPA-HCys-PDCA-modified gold nanoparticles can be used for rapid, easy and reliable screening of Hg(II) ions in aqueous solution, with high sensitivity (5 ppb) and selectivity over competing analytes. The hyper Rayleigh scattering (HRS) intensity increases 10 times after the addition of 20 ppm Hg(2+) ions to modified gold nanoparticle solution. The mechanism for HRS intensity change has been discussed in detail using particle size-dependent NLO properties as well as a two-state model. Our results show that the HRS assay for monitoring Hg(II) ions using MPA-HCys-PDCA-modified gold nanoparticles has excellent selectivity over alkali, alkaline earth (Li(+), Na(+), K(+), Mg(2+), Ca(2+)), and transition heavy metal ions (Pb(2+), Pb(+), Mn(2+), Fe(2+), Cu(2+), Ni(2+), Zn(2+), Cd(2+)).     

Ion-selective electrodes based on silver sulphide

A series of electrodes with membranes of silver sulphide have been prepared. Their standard potentials and their response to sulphide and silver ions are measured and compared with those of a single-crystal silver sulphide electrode. The selectivity parameters against heavy metal ions and halides, as well as cyanide, are discussed. It is concluded that only interferences from cyanide ions and mercury(II) ions are detrimental to the practical use of the electrodes for measuring pAg and pS.     

High adsorptive γ-AlOOH(boehmite)@SiO2/Fe3O4 porous magnetic microspheres for detection of toxic metal ions in drinking water

γ-AlOOH(boehmite)@SiO(2)/Fe(3)O(4) porous magnetic microspheres with high adsorption capacity toward heavy metal ions were found to be useful for the simultaneous and selective electrochemical detection of five metal ions, such as ultratrace zinc(II), cadmium(II), lead(II), copper(II), and mercury(II), in drinking water.     

Simultaneous determination of cadmium(II), lead(II) and copper(II) by using a screen-printed electrode modified with mercury nano-droplets

We are presenting a strategy for the fabrication of disposable screen-printed electrodes modified with mercury nano-droplets and capable of sensing heavy metal ions. They were prepared by coating electrodes with a mixture of multi-walled carbon nanotubes and chitosan, this followed by adsorption of mercury. The resulting sensor was characterized by cyclic voltammetry and impedance spectroscopy. Also the effects caused by adsorption of mercury were investigated. It is shown that square wave anodic stripping voltammetry enables simultaneous determination of cadmium(II), lead(II) and copper(II), for which detection limits of 12, 23 and 20 nM, respectively, are found. Relative standard deviations for ten determinations at 0.6 µM concentrations of these ions are in the range of 3.0 to 5.7%. The applicability was tested by analyzing river water and showed recoveries between 94.1 and 104.6%, thus demonstrating its utility for in-field monitoring of these heavy metal ions.     

聚苯胺及其复合物对重金属离子的高效吸附性能

基于国外最新文献,系统总结了近年来聚苯胺及其复合物的制备方法及其重金属离子吸附性能,重点分析了吸附性能特征,指出聚苯胺及其复合物具有吸附下限浓度低、达到吸附平衡快以及解吸附性能优异等特点.填充有聚苯胺颗粒的吸附柱在动态处理初始浓度为83 ng/L的汞离子溶液时,经一次吸附与解吸循环操作后,汞离子的富集倍数可达120倍.应用于冷原子吸收光谱的待测样品的浓缩与富集,可以将汞的测试下限拓展到0.05 ng/L.聚苯胺及其复合物在痕量重金属离子的高效富集与灵敏探测等方面展示了广阔的应用前景.     

Liquid-liquid extraction of silver ion with benzothiacrown ether derivatives

The extraction behavior of mono-, poly-, anal bis-(benzothiacrown ether)s is studied for alkali, alkaline-earth, heavy, and transition metal ions in the presence of picrate. These ethers show high selectivity for silver ion. Silver extractions from binary and quaternary mixtures of silver with heavy or transition metal ions were successful, except for mixtures with mercury(II) ion. Silver was extracted from a copper ore with ca. 80% recovery.     

Synthesis, electrochemistry and metal binding properties of monosubstituted ferrocenoyl peptides with thioether-containing sidechains

Ferrocenoyl peptides incorporating thioether functionality respond more strongly to mercury(II) than to other heavy metal ions in solution. Compounds reported previously in this context are all 1,1′-disubstituted, and all include two or more sulfur-containing amino acids. To test whether two thioether groups are required for effective mercury binding by these systems, we have prepared a series of singly-substituted ferrocenoyl peptides from ferrocenecarboxylic acid and l-methionine, S-methyl-l-cysteine or S-trityl-l-cysteine, and tested them as electrochemical probes for mercury(II). Nine ferrocenoyl peptides have been synthesised using a Boc-protecting group strategy and HBTU-mediated peptide coupling. The electrochemical properties of these compounds have been determined using cyclic voltammetry, and all show fully reversible one electron oxidation steps. Forward sweep half wave peaks (E_F), reverse sweep half wave peaks (E_R), peak separations (ΔE_P) and half wave potentials (E_1/2) are reported. Changes in the potential of the iron(II)/iron(III) redox couple of the ferrocene core have been used to quantify heavy metal-peptide interactions, revealing that these monotopic systems also respond more strongly to mercury(II) than to zinc(II), cadmium(II), silver(I) and lead(II). NMR experiments to characterise the peptide-mercury interaction implicate the thioether sulfur as the site of mercury binding and indicate 1:1 stoichiometry. The crystal structure of ferrocenoyl-S-methyl-l-cysteine methyl ester is also reported. The greater responsiveness of these systems to mercury(II) makes them interesting leads for the development of biologically inspired sensors for this toxic heavy metal.     

Mercury Films on Commercial Carbon Screen‐Printed Devices for the Analysis of Heavy Metal Ions: a Critical Evaluation

The suitability of mercury films on commercial screen‐printed electrodes for the analysis of heavy metal ions is critically tested for the particular case of Pb(II)‐ions. Although determination is possible by anodic stripping voltammetry with a reasonable detection limit (8.9 µg L^?1), important drawbacks are noticed as a consequence of the heterogeneous deposition of mercury on the rough surface of screen‐printed devices.     

Characterization of graphite–polyurethane composite electrodes modified with organofunctionalized SBA-15 nanostructured silica in the presence of heavy metal ions. Application to anodic stripping voltammetry

A graphite–polyurethane composite electrode with Santa Barbara Amorphous 15, SBA-15, mesoporous silica organofunctionalized with 2-benzothiazolethiol (BTSBA) as bulk modifier has been characterized electrochemically by voltammetry and electrochemical impedance spectroscopy (EIS) in the presence of cadmium ions, as an example of a toxic trace heavy metal, as well as by solid-state ¹³C-NMR and by scanning electron microscopy. EIS measurements performed on the modified composite electrodes to investigate the influence of BTSBA on the deposition of cadmium during square wave anodic stripping voltammetry showed that organofunctionalization of the SBA-15 bulk modifier in the composite electrode facilitates heavy metal deposition. Experiments were also carried out with a mixture of submicromolar cadmium, lead, copper and mercury ions and led to similar conclusions.     

Mercury binding by ferrocenoyl peptides with sulfur-containing side chains: Electrochemical, spectroscopic and structural studies

Ferrocenoyl peptides incorporating amino acids derived from either l-methionine, l-cysteine or dl-homocysteine have been synthesised and investigated as agents for heavy metal binding and detection. Heavy metal-peptide interactions have been characterised using cyclic voltammetry to follow changes in the potential of the Fe(II)/Fe(III) redox couple, revealing that these systems interact with mercury(II) ions more strongly than with other thiophilic heavy metals such as cadmium(II), silver(I) and lead(II). Proton NMR experiments have demonstrated 1:1 peptide:mercury binding and enabled quantitative characterisation of this binding interaction. Crystal structures for two of these ferrocenoyl peptide derivatives have been elucidated, revealing that these compounds adopt a P-1,3′ open solid state conformation in the absence of mercury; this arrangement precludes intramolecular hydrogen bonding between chains, while extensive intermolecular hydrogen bonding is evident. The particular affinity of these systems for mercury(II) opens the possibility of incorporating them in new, biologically inspired sensors for detecting this toxic pollutant.     

Synthesis and properties of a chelating resin containing triazolethiol groups

A macroreticular poly(acrylic acid)-based resin with triazolethiol as the functional group has been synthesized. The stability of the resin in acidic media and the behaviour in sorption and desorption of various metal ions have been investigated and compared with those of the acylthiosemicarbazide resin which is an intermediate in synthesis of the triazolethiol resin. Both resins show high affinity for copper(II) silver, cadmium and mercury(II), and high selectivity for silver and mercury(II) at low pH (1–2), and even at pH 7 if EDTA is present. The triazolethiol resin sorbs metal ions faster than the acylthiosemicarbazide resin does and sorbs mercury(II) from high concentrations of acids and neutral salt solutions. This resin has been applied to the concentration of silver and mercury(II) from sea-water samples by column operation.     

Heavy metal ion adsorption onto polypyrrole-impregnated porous carbon

Polypyrrole-impregnated porous carbon was readily synthesized using vapor infiltration polymerization of pyrrole monomers. The results show that the functionalized polymer layer was successfully coated onto the pore surface of carbon without collapse of mesoporous structure. The modified porous carbon exhibited an improved complexation affinity for heavy metal ions such as mercury, lead, and silver ions due to the amine group of polypyrrole. The introduced polypyrrole layer could provide the surface modification to be applied for heavy metal ion adsorbents. Especially, polymer-impregnated porous carbon has an enhanced heavy metal ion uptake, which is 20 times higher than that of adsorbents with amine functional groups. Furthermore, the relationship between the coated polymer amount and surface area was also investigated in regard to adsorption capacity.     

Mercury(II) ion-selective electrodes based on p-tert-butyl calix[4]crowns with imine units.

A PVC membrane incorporating p-tert-butyl calix[4]crown with imine units as an ionophore was prepared and used in an ion-selective electrode for the determination of mercury(II) ions. An electrode based on this ionophore showed a good potentiometric response for mercury(II) ions over a wide concentration range of 5.0 x 10(-5) - 1.0 x 10(-1) M with a near-Nernstian slope of 27.3 mV per decade. The detection limit of the electrode was 2.24 x 10(-5) M and the electrode worked well in the pH range of 1.3 - 4.0. The electrode showed a short response time of less than 20 s. The electrode also showed better selectivity for mercury(II) ions over many of the alkali (Na+, -1.69; K+, -1.54), alkaline-earth (Ca2+, -3.30; Ba2+, -3.32), and heavy metal ions (Co2+, -3.67; Ni2+, -3.43; Pb2+, -3.31; Fe3+, -1.82). Ag+ ion was found to be the strongest interfering ion. Also, sharp end points were obtained when the sensor was used as an indicator electrode for the potentiometric titration of mercury(II) ions with iodide and dichromate ions.     

Retention of radionuclides on metal sulphide precipitates

The retention of various radionuclides on metal sulphide precipitates has been studied. The sulphide precipitates quantitatively retained the common radionuclides. The condition for 100% retention in a thin layer is small particle size (a few μm) in the precipitate. This can be ensured by pulverization of the dried precipitate of metal sulphide. ²⁰³Hg²⁺ is retained by mercury sulphide and ⁶⁵Zn²⁺ by zinc sulphide by isotopic exchange. The retention of foreign radioactive ions can be reduced or even eliminated by counter-carrier technique in cases where the retention is not due to chemical reaction, precipitate exchange. The isotopic exchange with mercury(II) sulphide and zinc sulphide enables mercury and zinc ions to be separated rapidly and determined in the presence of a number of interfering ions.     

Anodic stripping voltammetry in a flow-through cell with a fixed mercury film glassy carbon disc electrode. Part I

Anodic stripping voltammetry at a glassy carbon disc electrode covered by a thin mercury film was adapted for use in a flow-through cell. The resulting system is characterized by extreme simplicity of set-up and operation, high sensitivity and excellent precision and stability. Its performance was tested via the determination of hydrated or labile complex ions of heavy metal ions in sea water, using short (2–10 min) deposition periods. The dependence of the stripping peak charge on metal ion concentration, length of deposition period, solution flow rate and other variables was examined and the reliability of the results obtained were evaluated under conditions resembling continuous monitoring.     

On solute-mercury interactions in dilute amalgams of main group metals

The paper challenges the concept of intermetallic compound formation in dilute (mole fraction <10⁻³) amalgams of s-block metals. Although the formation of these amalgams is strongly exothermic the generated energy is much lower than the Fermi level difference between pure solutes and mercury. Thermodynamic considerations suggest that the energy of metal ions is higher in amalgams than in pure s-block metals. Repulsive interactions between the cores of these metals and mercury ions are responsible for abnormally low diffusion coefficients of alkali and alkaline earth metals in mercury. The mercurophobic character of alkali metal ions demonstrates itself in the strong adsorption of these metals on the Hg-vacuum interface, and in the high rates of ion exchange between electrolytic solutions and amalgams.     

石墨烯基微电极的制备及其在电化学传感中的应用

微电极由于灵敏度高、响应快、样品用量少、操作简便等特点,近年来在化学分析、生物医学、食品安全、环境检测等领域引起人们的广泛关注。 石墨烯具有超高的比表面积、优异的电子迁移率及良好的生物相容性等优点,近年来在电化学传感领域展示出巨大的发展前景。 本文围绕石墨烯基微电极的制备及其在电化学传感中的应用展开,总结了近年来国内外同行基于石墨烯修饰微电极和石墨烯微电极在重金属离子、多巴胺、葡萄糖、H₂O₂等分子检测方面取得的研究成果。 同时探讨了石墨烯基微电极在电化学传感方面面临的挑战和发展前景。