常温预辐射聚合法物理包埋葡萄糖氧化酶的研究

Most of bioactive species such as enzyme and antibody will be damaged and lose part of their bioactivity when they are irradiated by ionizing radiation at room temperature. Low temperature could somewhat control the effect, so kaetsu and his co-workers developed an entrapping technique at low temperature ( - 78℃). On the other hand, some enzymes such as catalase and house radish peroxidase have so-called radiation-induced post-deactivation effect as well. In order to avoid the trouble in performance and loss of bioactivity, a physical ent-rapping of bioactive species via preirradiation polymerization at room temperature were deve-loped in the Authors'lab. In this work we developed this technique. The glucose oxidase was entrapped in polyacrylamide hydrogel ind uced by pre-irradiation. Experiments under several different conditions such as absorbed dose and concentrations of enzymes,monomer and crosslinking agent were carried out. The results showed that this technique can be used ex-tensively in various enzyme.     

辐射聚合固定化α—淀粉酶的研究

用低温辐射聚合法将α-淀粉酶固定到聚甲基丙烯酸-β-羟乙酯载体上。研究了低温辐射聚合固定化的条件;讨论了不同固定化酶对淀粉转化成还原糖的相对活性及其重复使用的稳定性;探索了载体微孔结构与固定化酶活性的关系。结果表明,在真空体系内,酶用量≥250μg/mL、单体浓度在30％～40％之间,于-50℃～-55℃范围内进行5.6×10~5rad剂量的辐射聚合,所得固定化酶重复使用10多次其相对活性仍可保持在30％以上。     

生物功能电极 Ⅲ.葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合,将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响,并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现,由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性,酶反应表观上遵循Michealis-Menten动力学。     

以改性Al2O3为载体固定化葡萄糖氧化酶的研究

本文采用吸附和交联、生物和非生物催化剂结合的方法,制得活性高、稳定性好并以Al_2O_3.为载体的固定化葡萄糖氧化酶,其性能优于文献报导的结果.     

生物功能电极 III. 葡萄糖氧化酶的电化学固定化研究

利用磷酸盐缓冲溶液中吡咯的电聚合, 将葡萄糖氧化酶(GOD)包埋在聚吡咯(PPy)基质中以构成生物功能电极。讨论了溶液pH和聚合电位对酶固定化的影响, 并用IR和交流阻抗谱对酶膜进行表征。GOD的固定化只有当pH>5.5时才能实现, 由此推测酶是以带负电的粒子嵌入PPy的。交流阻抗谱表明这一电极具有有界多孔电极的特征。探索了酶与电子传递体Fe(CN)_6~(3-)同时固定化的可行性。电化学固定化的GOD保持其生物催化活性, 酶反应表观上遵循Michealis-Menten动力学。     

聚乙烯－葡萄糖氧化酶膜的制备和性能研究

聚乙烯－葡萄糖氧化酶膜的制备和性能研究朱如瑾，殷弘浩，刘永盛，黄家湛（成都高分子材料国家重点实验室成都科技大学高分子研究所成都６１００６５）关键词聚乙烯，等离子体，固定化酶，葡萄糖氧化酶固定化酶是６０年代发展起来的生物工程技术Ｉ‘］．酶的固定化方法主...     

聚乙烯－葡萄糖氧化酶膜的制备和性能研究

聚乙烯－葡萄糖氧化酶膜的制备和性能研究朱如瑾，殷弘浩，刘永盛，黄家湛（成都高分子材料国家重点实验室成都科技大学高分子研究所成都６１００６５）关键词聚乙烯，等离子体，固定化酶，葡萄糖氧化酶固定化酶是６０年代发展起来的生物工程技术Ｉ‘］．酶的固定化方法主...     

固定化葡萄糖氧化酶的制备及稳定性研究

选用自制的磁性纳米四氧化三铁为酶固定化的载体,通过交联法来固定葡萄糖氧化酶。通过对酶固定化过程中一系列因素的研究,确定出酶固定化的最佳工艺为:交联剂戊二醛与浓度为0.7 mg/mL酶液的体积比为1:4,固定化时间为0.5 h,固定化温度为室温(≤20 ℃),固定化所用缓冲液pH=7。采用比色法测定其酶活力。结果表明葡萄糖氧化酶经过固定化后,其酶活力较游离酶显著增加。固定化酶的热稳定性、酸碱稳定性、存储稳定性都有很大的提高。     

利用壳聚糖的絮凝性质包埋酶的葡萄糖氧化酶电极

本文利用壳聚糖的絮凝性质，将葡萄糖氧化酶包埋在壳聚糖与多聚磷酸盐的絮絮沉淀中，操作简单，固定化效率高。研究了适合了酶电极使用的最佳固定化条件。     

脂质体为模板仿生硅化固定葡萄糖氧化酶

将脂质体囊泡与仿生硅化技术相结合,模拟细胞纳微环境,实现以脂质体为模板仿生制备氧化硅固定葡萄糖氧化酶(GOx),建立性能稳定的固定化酶.扫描电镜分析显示,固定化GOx为球形纳米粒子,粒径分布在200nm左右,在优化反应条件下GOx回收率达到71.8%.由于载体的空间限制作用及其提供的较稳定微环境,固定化GOx表现出良好的热稳定性和pH稳定性,其对变性剂耐受性和操作稳定性等也得到明显提高.     

丙烯酰胺微乳液聚合

由乳化剂聚乙二醇壬基苯基醚ＯＰ、聚乙二醇壬基苯基醚（ＴＸ—４）、丙烯酸胺、水和煤油组成微乳液时，体系中水相丙烯酸胶浓度及体系温度对乳化剂最小量有明显的影响；而ＯＰ、ＴＸ—４比例及油水比例的影响不大．本文研究了辐射引发微乳液聚合的动力学，得到如下表达式：聚合速率及聚合物特性粘数的表观活化能分别为５３．２ＫＪ／ｍｏｌ，－３３．２ＫＪ／ｍｏｌ．聚丙烯酸胺微乳液具有特殊的增稠性能，与聚电解质增稠剂相比，电解质对增稠效果的影响不大，而其他表面活性剂的影响较大．     

苯甲醛及其衍生物对铈离子存在下丙烯酰胺聚合的影响

<正> 虽然Santappa等早已报道Ce~(4+)(高氯酸铈)/甲醛体系能引发丙烯腈(AN)、甲基丙烯酸甲酯(MMA)的聚合,但对醛的活性以及参与引发单体聚合的自由基都未有详细报道,近来孙燕慧等发现脂肪醛能显著促进Ce~(4+)(硝酸铈铵CAN)引发丙烯酰胺(AAM)的聚合,而且醛的活性远大于相应的醇。至于芳香醛对于Ce~(4+)引发烯类单体的聚合的影响也未见详细报道。本文扼要报道苯甲醛(BA)及其衍生物对-硝基苯甲醛(PNBA)、间-硝基苯甲醛(MNBA)、间-溴苯甲醛(MBBA)、对-氯苯甲醛(PCBA)对Ce~(4+)(CAN)存在下丙烯酰胺聚合的影响,测定了其聚合速率,以UV吸收光谱、ESR波谱测定     

PHOTO-INDUCED GRAFT POLYMERIZATION OF ACRYLAMIDE ON POLYPROPYLENE MEMBRANE SURFACE IN THE PRESENCE OF DIBENZYL TRITHIOCARBONATE

Ultraviolet （UV）-induced graft polymerization of acrylamide （AAm） on polypropylene substrates was successfully conducted using dibenzyl trithiocarbonate （DBTTC） as photoinitiator. It was confirmed by chemical analysis and surface morphology observation with attenuated total reflectance Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. A possible mechanism for this graft process was presented, which suggested that, under UV irradiation, the C： S bond in DBTTC could split and abstract a hydrogen from the polypropylene surface and a surface free radical was then formed, and initiated the graft polymerization of AAm.     

六氟丙烯等离子体聚合的研究

求得了六氟丙烯等离子体聚合物(PPHFP)膜的热裂解反应活化能为101.6 kJmol~(-1),半分解温度为322℃。讨论了不同条件下聚合速率的变化,找出了反应器内各点的聚合速率与压力的关系曲线,同时也证实了N_2作等离子气体时,N可以化学键的形式进入PPHFP膜结构。     

辐照温度对聚芳醚酮辐射交联行为的影响

<正> 可溶性含酚酞侧基聚芳醚酮(PEK-C)是一种新型的具有耐高温、耐水解、耐化学腐蚀、自润滑性能的工程塑料,它具有如下结构:     

STUDY ON THE MECHANISM OF 1-OCTENE ZIEGLER-NATTA POLYMERIZATION BASED ON THE NUMBER OF ACTIVE CENTERS

The number of active centers (C_p)-t and k_p-t profiles of Solvay type TiCl_3 - AlR_3 (R=C_2H_5, i-C_4H_9) or Stauffer AA TiCl_3-Al (C_2H_5)_3 catalyzed 1-octene polymerization were determined by using an acetyl chloride quenching method as well as kinetic data. The results show that in the studied systems k_p decreases when C_p increases, indicating the presence of two or more types of different active centers. The C_(p~(-t)) plots of the Solvay TiCl_3-AlR_3 systems show the presence of both stable active centers and unstable centers which decay in the polymerization process. The phenomena are explained based on a model of active center plurality. The increases of C_p in the induction periods are also discussed.     

铈离子与乙酰苯胺及其衍生物引发丙烯酰胺聚合动力学的研究

以铈离子和酰苯胺引发体系进行丙烯酰胺的聚合,研究了不同结构酰苯胺对聚合的影响。在H_2O-CH_3CN(3∶1)介质中聚合时,乙酰对甲苯胺对聚合的促进作用最为明显,聚合速度可提高一个数量级。测定了聚合反应的表观活化能和聚合动力学方程、由聚合物的原子发射光谱,UV光谱和端基测定,提出了聚合反应机理。     

STUDY ON NYLON 6/SUPERFINE RUBBER PARTICLES COMPOSITES VIA IN SITU POLYMERIZATION

Two highly cross-linked superfine styrene-butadiene rubber particles, one with 1 wt% of carboxyl groups and theother without such groups having particle sizes of 130-150 nm and 80-100 nm respectively, were used to prepare nylon6/rubber composites via in situ polymerization. It was found that carboxylic styrene-butadiene dispersed uniformly in nylonmatrix and there was strong interfacial interaction because of the graft polymer formed by the reaction of nylon with carboxylgroup of the rubber, resulting in considerably improved impact strength with almost unchanged tensile strength. However,the addition of styrene-butadiene without carboxyl groups showed intensive agglomeration of the rubber particles and weakinterfacial interactions, and the toughness of the materials was improved slightly. The crystallization and rheological behavior of the composites were also discussed.     

1,3-戊二烯阳离子聚合过程中环化反应的研究

以ＡｌＣｌ３和（ＣＦ３ＳＯ３）３Ａｌ为引发剂，ＣＨ２Ｃｌ２为溶剂，在２０℃聚合了１，３ 戊二烯（ＰＤ）．对聚合物（ＰＰＤ）的结构分析表明，（ＣＦ３ＳＯ３）３Ａｌ生成的聚合物具有较高的环化度．聚合物的环化过程是通过两种机理，分子内链转移机理和阳离子引发机理，后者可以通过加入ＤｔＢＰ得到抑制．ＡｌＣｌ３引发的聚合反应中环化过程以前一种机理为主，而（ＣＦ３ＳＯ３）３Ａｌ则以后一种机理为主．通过阳离子引发的环化反应主要发生在ＰＰＤ１，２单元侧基双键上