Characterisation of inhibitors of acetylcholinesterase by an automated amperometric flow-injection system

Acetylcholinesterase was immobilised on magnetic particles and integrated in a flow-injection system via a magnetic reactor. Enzyme activity was determined amperometrically using acetylthiocholine chloride as enzyme substrate. This system was applied to enzyme inhibition tests. Inhibition constants and lower detection limits were determined for carbofuran, paraoxon, malaoxon and paraoxon-methyl. The resulting data were compared to those obtained with a photometric test, i.e. the determination of thiocholine via its reaction with the Ellman's reagent 5,5'-dithio-bis-2-nitrobenzoic acid using the same flow system. As they correlated well to those reported for the native enzyme the flow-injection analysis device can be applied to automated determination and characterisation of enzyme inhibitors.     

Sunflower leaves tissue-based bioelectrode with amperometric flow-injection system for glycolic acid determination in urine

A novel plant tissue-based bioelectrode obtained by incorporating sunflower (Helianthus annuus L.) leaves tissue as a source of glycolate oxidase and peroxidase into a ferrocene-mediated carbon paste electrode for the determination of glycolic acid was developed. It was coupled with the flow-injection (FI) system and used as the basis to develop a novel FI amperometric procedure for glycolic acid determination. The flow-injection amperometric measurements were performed by injecting aliquot of glycolic acid solution into the flowing stream of 0.05 mol L⁻¹ of phosphate buffer solution having pH 8.0 with a flow rate of 0.3 mL min⁻¹. The bioelectrode consisted of 20% (w/w) of sunflower leaves tissue and 5% (w/w) of ferrocene at 0.00 V (vs Ag/AgCl). The bioelectrode exhibited a linear response from 1.0 × 10⁻⁶ up to 2.0 × 10⁻³ mol L⁻¹ glycolic acid with a detection limit (S/N = 3) and a quantitation limit (S/N = 10) of 1 × 10⁻⁶ and 3.3 × 10⁻⁶ mol L⁻¹, respectively. The sampling rate of 12 h⁻¹ and a relative standard deviation of 1.67% (n = 15) were achieved. The bioelectrode response decreased to 70% of the original value within 90 continuous injections. The proposed bioelectrode was satisfactorily applied to glycolic acid determination in human urine samples after appropriate sample pretreatment. Results obtained by the FI method were compared favorably with those obtained by HPLC. It offers advantages, which included rapidity, high activity, limited stability, ease of preparation and low cost.     

流动注射电化学发光分析法测定氨苄西林

基于氨苄西林对鲁米诺在铂电极上弱的电氧化发光信号的强增敏作用与流动注射技术的结合,建立了一种测定氨苄西林的电化学发光分析新方法。该法测定氨苄西林的检出限为5.0×10-8g mL,线性范围为8.0×10-8～5.0×10-5g mL,相对标准偏差为2.0%(n=11)。已成功地用于样品中氨苄西林的测定。     

Development of an amperometric immunosensor based on flow injection analysis for the detection of red blood cells

An amperometric immunosensor, based on a non-competitive sandwich assay and flow injection analysis (FIA), was developed for the detection of human red blood cells (RBCs). A dual working electrode, on which specific IgM and nonspecific IgM were chemically immobilised to form sensing and blank electrodes, respectively, was employed to determine the binding of specific blood cells and non-specific adsorption in one determination. Horseradish peroxidase (HRP)-labelled antiblood group A IgM was used in the assay. Sensor preparation involved chemical immobilisation of the IgMs on glassy carbon electrodes using l-ethyl-3(3-dimethyl aminopropyl)carbodiimide (EDC) as a coupling reagent in the presence of N-hydroxysuccinimide (NHS). The interference contributions, such as the non-specific adsorption of the enzyme conjugate and the blood cells, were determined and removed. A quantitative relationship between the cell binding response and its concentration was obtained in the region 1 − 30 × 10⁸ cells ml⁻¹.     

流动注射结合化学发光法测定没食子酸

基于没食子酸与铬 (Ⅵ )的氧化还原反应 ,产生的铬 (Ⅲ )催化鲁米诺 H2 O2 化学发光体系的研究 ,结合流动注射技术 ,优化反应条件 ,建立了一种高灵敏度的快速测定没食子酸的新方法。方法的线性范围为 2 .0× 1 0 - 9～ 5 .0× 1 0 - 6g/mL ,检出限为 1 .2× 1 0 - 9g/mL ,对 1 .0× 1 0 - 7g/mL的没食子酸进行了 1 1次平行测定 ,相对标准偏差为 2 .1 %。方法成功地用于健民咽喉片中没食子酸的测定。     

Amperometric detection of amino acids in a flow-injection system with a nickel(II)-modified electrode with an Eastman-AQ polymer film

Amperometic flow measurements were made at +0.55 V (vs. Ag/AgCl) in 0.1 mol l⁻¹ KOH electrolyte with an Ni(II) chemically modified electrode (CME) with an Eastman-AQ polymer film. The use and characteristics of a Ni(II)-containing crystalline and polymer-modified electrode obtained by a double coating step as a detector for amino acids in a flow-injection system using reversed-phase liquid chromatography are described. The detection of these analytes is based on the higher oxidation state of nickel (NiOOH) controlled by the applied potential. The electroanalytical parameters and the detection current for a series of amines and amino acids were investigated. The use of such a CME in the flow-injection technique was found to be suitable in a solution at low pH. The linear range for glycine is 5 × 10⁻⁶-0.1 mol l⁻¹ with a detection limit of 1.0×10⁻⁶ mol l⁻¹. A 1 × 10⁻⁴ mol l⁻¹ mixture of serine and tyrosine was also detected after separation on an Nucleosil C₁₈ column.     

Monitoring of mouse immunoglobulin G by flow-injection analytical affinity chromatography

A flow-injection analytical affinity chromatographic (FIAAC) system was developed for the on-line monitoring of mouse immunoglobulin G (IgG). Protein A or anti-mouse IgG antibodies immobilized on oxirane beads were filled in a miniature column. The IgG-containing samples and standards were passed through the column and detected fluorimetrically after elution with citrate buffer (pH 3 or 2.5). The on-line monitoring of mouse IgG 2a during a 7-day cultivation of hybridoma cells in a perfusion reactor by FIAAC is presented. A chemical barrier was used to prevent contamination of the reactor from the FIAAC.     

Spectrophotometric determination of catecholamines with metaperiodate by flow-injection analysis

A flow-injection Spectrophotometric method for the determination of adrenaline and isoprenaline, based on the reaction with metaperiodate, is described. The calibration graphs are linear up to 2 × 10⁻⁴ M. Flow injection allows the measurement of 120 samples per hour. The method was successfully applied to the determination of both catecholamines in pharmaceuticals.     

流动注射在线过滤稀释原子吸收法测定诺氟沙星

提出了流动注射在线过滤稀释原子吸收法测定诺氟沙星的新方法。药物浓度在0．1－0．8mg/mL范围符合比耳定律，回收率为97．9％－102．4％，相对标准偏差为1．7％。方法可用于诺氟沙星胶囊测定。     

Selective flow-injection determination of methanol in the presence of ethanol based on a multi-enzyme system with chemiluminescence detection

A highly selective flow-injection system was developed for the determination of methanol. The system consisted of three immobilized enzymes with luminol chemiluminescence detection. First, methanol was oxidized in the presence of alcohol oxidase to yield formaldehyde and hydrogen peroxide. The hydrogen peroxide produced was then destroyed by catalase. The formaldehyde formed in the first stage was further oxidized by NAD⁺-formaldehyde dehydrogenase. The NADH formed was oxidized by 1-methoxy-5-methylphenazinium methylsulphate (1-MPMS), and finally the reduced 1-MPMS was spontaneously oxidized and hydrogen peroxide was produced. The concentration of the hydrogen peroxide produced, which was proportional to the initial concentration of methanol, was determined by luminol chemiluminescence. The determination range was from 0.1 to 100 mg l⁻¹ and the response time was less than 2 min per sample with a relative standard deviation of less than 3%. The system showed good selectivity for methanol; the response was ca. 50 times higher than for ethanol.     

流动注射化学发光法测定己内酰胺

使用己内酰胺增强Ce(Ⅳ) SO32-化学发光体系,结合流动注射分析技术进行了己内酰胺的测定。己内酰胺的质量浓度在4.0×10-7～1.0×10-5g/mL范围内与化学发光分析信号呈线性关系,其检出限为1×10-7g/mL。对4.0×10-7g/mL的己内酰胺溶液进行11次连续测定,相对标准偏差为2.1%。方法已应用于层析用聚己内酰胺中的己内酰胺测定。     

Flow electrochemical biosensors based on enzymatic porous reactor and tubular detector of silver solid amalgam

A flow amperometric enzymatic biosensor for the determination of glucose was constructed. The biosensor consists of a flow reactor based on porous silver solid amalgam (AgSA) and a flow tubular detector based on compact AgSA. The preparation of the sensor and the determination of glucose occurred in three steps. First, a self-assembled monolayer of 11-mercaptoundecanoic acid (MUA) was formed at the porous surface of the reactor. Second, enzyme glucose oxidase (GOx) was covalently immobilized at MUA-layer using N-ethyl-N′-(3-dimethylaminopropyl) carboimide and N-hydroxysuccinimide chemistry. Finally, a decrease of oxygen concentration (directly proportional to the concentration of glucose) during enzymatic reaction was amperometrically measured on the tubular detector under flow injection conditions. The following parameters of glucose determination were optimized with respect to amperometric response: composition of the mobile phase, its concentration, the potential of detection and the flow rate. The calibration curve of glucose was linear in the concentration range of 0.02–0.80 mmol L⁻¹ with detection limit of 0.01 mmol L⁻¹. The content of glucose in the sample of honey was determined as 35.5 ± 1.0 mass % (number of the repeated measurements n = 7; standard deviation SD = 1.2%; relative standard deviation RSD = 3.2%) which corresponds well with the declared values. The tested biosensor proved good long-term stability (77% of the current response of glucose was retained after 35 days).     

Chemiluminometric -lysine determination with immobilized lysine oxidase by flow-injection analysis

An enzymatic flow-injection procedure for the determination of -lysine was developed. A lysine oxidase reactor is combined with a fibre-optic hydrogen peroxide detector. Hydrogen peroxide detection is based on the peroxidase-catalysed luminol reaction. The chemiluminescent light is detected by a photomultiplier. -Lysine can be determined in the range 10–1000 μM. A sampling rate of up to 90 h⁻ can be achieved. The whole sensing assay works for more than 1 month. The double logarithmic graph of the peak signal height vs. the lysine concentration is linear, the slope being larger than unity (r² = 0.991, n = 4).     

采用带微型预处理柱和分离柱的FIA分光光度系统同时测定硅和磷

用阳阴离子交换柱和流动注射分析组合,建立了在线预处理和预分离同时测定磷和硅的FIA方法。用本法测定了头发、淡菜、茶叶、马尾藻和大米中的硅和磷。方法的测定范围为1．0mg/L-24mg/L(PL4^3-),0.5mg/L-12mg/L(SiO3^2-),回收率：96.7%-99.0%(PO4^3-),100%-102%(SiO3^2-);RSD(PO4^3-)=1.3%,RSD(SiO3^2-)=1.8%。     

流动注射化学发光抑制法测定阿魏酸钠

提出了Fe2+-H2O2-亚甲基蓝化学发光新体系并用于阿魏酸钠的测定。实验发现,在酸性介质中,Fe2+-H2O2体系可与亚甲基蓝反应产生极强的化学发光,阿魏酸钠对此化学发光具有显著的抑制作用。据此,结合流动注射技术,建立了阿魏酸钠化学发光分析新方法。研究了影响化学发光强度的因素,化学发光信号的降低值(ΔI)与阿魏酸钠浓度在4.5×10-6～4.5×10-5mol/L范围内呈良好的线性关系,方法的检出限为7.0×10-7mol/L。对4.8×10-6mol/L的阿魏酸钠进行了11次平行测定,其RSD=0.8%,该法已用于片剂中阿魏酸钠含量的测定。     

Batch and flow-injection methods for the spectrophotometric determination of olanzapine

An indirect batch spectrophotometric and direct flow-injection (FI) visible spectrophotometric methods have been developed for the determination of the novel anti-psychotic drug olanzapine (OLA). The batch method is based on the oxidation of olanzapine by a known excess of potassium hexacyanoferrate(III) in the presence of the mixture of sulphuric and phosphoric acids (1:1 (v/v)). The absorbance of unreacted oxidant is measured at 425 nm. The absorbance decreases linearly with increasing concentration of the assayed drug. The FI method with detection at 540 nm is based on the direct oxidation of olanzapine one of two oxidants, cerium(IV) sulphate or potassium hexacyanoferrate(III) in acidic medium. The calibration graph were linear over the range of 2.5-40 μg ml⁻¹ in the batch method and 0.05-300 and 0.5-250 μg ml⁻¹ in the FI methods, used cerium (IV) sulphate and potassium hexacyanoferrate (III) respectively. Both FI methods gave similar results in terms of precision and accuracy. The relative standard deviation (R.S.D.), was <1%. The accuracy, obtained from recovery experiments, was 97.9-99.4%. The batch method gave slightly higher R.S.D. values (up to 2.3%) and lower values of accuracy (the recovery was between 96.5 and 96.6%). The methods developed were applied to the determination of olanzapine in a pharmaceutical product.     

流动注射在线过滤稀释原子吸收测定药物制剂中安乃近的方法研究

提出了测定安乃近的FI-AAS分析新方法。此法基于在适当酸度条件下安乃近将Cu^2 还原为Cu^ ，新生成的Cu^ 与SCN^-生成沉淀，经流动注射在线过滤稀释，以AAS法测定反应剩余Cu^2 的量来间接测定安乃近的含量。安乃近的浓度在2-100mg/L范围内吸收值呈良好的线性关系。回收率为97.0%-102.5%，采样频率为100次/h。     

流动注射示差动力学分析法提高测定的选择性

本文归纳了流动注射示差动力学分析法所基于的化学反应和常用的流路,评述了流动注射示差动力学分析法在单一组分的高选择性测定和多组分的连续或同时测定中的应用。     

Recent developments concerning the investigation of exocytosis with amperometry

In this article, we have summarized the recent important results related to the electrochemical detection of vesicular exocytosis by amperometry with microelectrodes over the past three years. In this fascinating scientific field that began 40 years ago, the historical carbon fiber amperometry method still continues to be used to address biological questions by the pioneered groups of the field but also by other research groups thus showing this has become an indispensable routine technique for analyzing exocytosis. Furthermore, new methodologies (coupling with fluorescence, use of nanoelectrodes, microarrays) have blossomed and demonstrated how new analytical methods could be built to push back the limits of the initial technique.     

Highly sensitive and selective amperometric sensors for nanomolar detection of iodate and periodate based on glassy carbon electrode modified with iridium oxide nanoparticles

Iridium oxide nanoparticles are grown on a glassy carbon electrode by electrodepositing method. The electrochemical behavior and electrocatalytic activity of modified electrode towards reduction of iodate and periodate are studied. The reductions of both ions occur at the unusual positive peak potential of 0.7 V vs. reference electrode. The modified electrode is employed successfully for iodate and periodates detection using cyclic voltammetry, hydrodynamic amperometry and flow injection analysis (FIA). In the performed experiments, flow injection amperometric determination of iodate and periodate yielded calibration curves with the following characteristics: linear dynamic range up to 100 and 80 μM, sensitivity of 140.9 and 150.6 nA μM⁻¹ and detection limits of 5 and 36 nM, respectively. The repeatability of the modified electrode for 21 injections of 1.5 μM of iodate solution is 1.5%. The interference effects of NO₂⁻, NO₃⁻, ClO₃⁻, BrO₃⁻, ClO₄⁻, SO₄²⁻, Cu²⁺, Zn²⁺, Mn²⁺, Mg²⁺, Cd²⁺, Ca²⁺, Na⁺, K⁺, NH₄⁺ and K⁺, CH₃COO⁻ and glucose were negligible at the concentration ratio of more than 1000. The obtained attractive analytical performance together with high selectivity and simplicity of the proposed method provide an effective and e novel modified electrode to develop an iodate and periodate sensor. Sensitivity, selectivity, the liner concentration range and the detection limit of the developed sensor are all much better than all known similar sensors in the literature for iodate and periodate determination.