Optimization of pressurized liquid extraction and purification conditions for gas chromatography-mass spectrometry determination of UV filters in sludge

This work presents an effective sample preparation method for the determination of eight UV filter compounds, belonging to different chemical classes, in freeze-dried sludge samples. Pressurized liquid extraction (PLE) and gas chromatography-mass spectrometry (GC-MS) were selected as extraction and determination techniques, respectively. Normal-phase, reversed-phase and anionic exchange materials were tested as clean-up sorbents to reduce the complexity of raw PLE extracts. Under final working conditions, graphitized carbon (0.5 g) was used as in-cell purification sorbent for the retention of co-extracted pigments. Thereafter, a solid-phase extraction cartridge, containing 0.5 g of primary secondary amine (PSA) bonded silica, was employed for off-line removal of other interferences, mainly fatty acids, overlapping the chromatographic peaks of some UV filters. Extractions were performed with a n-hexane:dichloromethane (80:20, v:v) solution at 75°C, using a single extraction cycle of 5 min at 1500 psi. Flush volume and purge time were set at 100% and 2 min, respectively. Considering 0.5 g of sample and 1 mL as the final volume of the purified extract, the developed method provided recoveries between 73% and 112%, with limits of quantification (LOQs) from 17 to 61 ng g(-1) and a linear response range up to 10 μg g(-1). Total solvent consumption remained around 30 mL per sample. The analysis of non-spiked samples confirmed the sorption of significant amounts of several UV filters in sludge with average concentrations above 0.6 μg g(-1) for 3-(4-methylbenzylidene) camphor (4-MBC), 2-ethylhexyl-p-methoxycinnamate (EHMC) and octocrylene (OC).     

iMatch: a retention index tool for analysis of gas chromatography-mass spectrometry data

A method was developed to employ National Institute of Standards and Technology (NIST) 2008 retention index database information for molecular retention matching via constructing a set of empirical distribution functions (DFs) of the absolute retention index deviation to its mean value. The effects of different experimental parameters on the molecules' retention indices were first assessed. The column class, the column type, and the data type have significant effects on the retention index values acquired on capillary columns. However, the normal alkane retention index (I(norm)) with the ramp condition is similar to the linear retention index (I(T)), while the I(norm) with the isothermal condition is similar to the Kováts retention index (I). As for the I(norm) with the complex condition, these data should be treated as an additional group, because the mean I(norm) value of the polar column is significantly different from the I(T). Based on this analysis, nine DFs were generated from the grouped retention index data. The DF information was further implemented into a software program called iMatch. The performance of iMatch was evaluated using experimental data of a mixture of standards and metabolite extract of rat plasma with spiked-in standards. About 19% of the molecules identified by ChromaTOF were filtered out by iMatch from the identification list of electron ionization (EI) mass spectral matching, while all of the spiked-in standards were preserved. The analysis results demonstrate that using the retention index values, via constructing a set of DFs, can improve the spectral matching-based identifications by reducing a significant portion of false-positives.     

Analysis of salicylate and benzophenone-type UV filters in soils and sediments by simultaneous extraction cleanup and gas chromatography-mass spectrometry

An analytical method for the determination of UV filters in soil and sediment has been developed and validated considering benzophenones (BP) and salicylates as target analytes. Soil and sediment samples were extracted with ethyl acetate-methanol (90:10, v/v) assisted with sonication, performing a simultaneous clean-up step. Quantification of these compounds was carried out by gas chromatography-mass spectrometry (GC-MS) after derivatization of the extracts with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA). Recoveries from spiked soil samples ranged from 89.8% to 104.4% and they were between 88.4% and 105.3% for spiked sediment samples. The effect of the residence time and soil moisture content on the recovery of these compounds was also studied. The precision, expressed as relative standard deviation, was in all cases below 6.1% and the limits of detection (S/N=3) varied from 0.07 to 0.10 ng g(-1) and from 0.11 to 0.28 ng g(-1) for soils and sediments, respectively. The validated method was applied to the analysis of five benzophenone and two salicylate UV filters in soil and sediment samples collected in different areas of Spain.     

Determination of emulsion explosives with Span-80 as emulsifier by gas chromatography-mass spectrometry

A novel approach for identification and determination of emulsion explosives with Span-80 (sorbitol mono-oleate) as the emulsifier and their postblast residues by gas chromatography-mass spectrometry (GC-MS) has been developed. 24 kinds of emulsion explosives collected have been processed by transesterification reaction with metholic KOH solution and the emulsifier has turned into methyl esters of fatty acids. From the peak area ratios of their methyl esters, most of these emulsion explosives can be differentiated. In order to detect the postblast residues of emulsion explosives, the sorbitols in the emulsifier Span-80 obtained after transesterification reaction have been further derivatized by silylation reaction with N,O-bis-(trimethylsilyl)trifluoroacetamide (BSTFA) containing 1% trimethylchlorosilane (TMCS) as the derivatizing reagent. The derivatization conditions were optimized and the derivatives were determined by GC-MS. The results showed that the silylation derivatives of sorbitol and it isomers, combined with hydrocarbon compounds and methyl esters of fatty acids, were the characteristic components for identification of the emulsion explosives. The established approach was applied to analyze the postblast residues of emulsion explosives. It has been found that the method was sensitive and specific, especially when detecting the derivatives of sorbitol and its isomers by GC-MS in selecting ion mode. The information of the characteristic components can help probe the origin of the emulsion explosives and providing scientific evidences and clues for solving the crimes of the emulsion explosive explosion.     

Screening of tetrodotoxin in puffers using gas chromatography-mass spectrometry

Tetrodotoxin (TTX), a toxic compound found in some puffers can cause death to humans through consumption. We have developed a simplified method for the screening of TTX in puffers using GC-MS. A puffer tissue of 0.5g was treated with 5mL of 0.1% acetic acid, followed by alkaline hydrolysis, LLE or liquid-liquid extraction and N-methyl-N-TMS-trifluoroacetamide derivatization. The developed method used only a small sample and solvent, simplified LLE and derivatization procedures and short chromatographic analysis (8.2min). All of these contribute to cost-saving, enhanced sample throughput and high sensitivity of the screening assay. The developed method was validated and proved to be within the acceptable range.     

Micro liquid-liquid extraction combined with large-volume injection gas chromatography-mass spectrometry for the determination of haloacetaldehydes in treated water

Haloacetaldehydes (HAs) are becoming the most widespread disinfection by-products (DBPs) found in drinking water, besides trihalomethanes and haloacetic acids, generated by the interaction of chemical disinfectants with organic matter naturally present in water. Because of their high potential toxicity, HAs have currently received a singular attention, especially trichloroacetaldehyde (chloral hydrate, CH), the most common and abundant compound found in treated water. The aims of this study are focused on the miniaturisation of EPA Method 551.1, including some innovations such as the use of ethyl acetate as the extracting solvent, the enhancement of HAs stability in aqueous solutions by adjusting the pH ~3.2 and the use of a large-volume sample injection (30 μL) coupled to programmed temperature vaporizer-gas chromatography-mass spectrometry to improve both sensitivity and selectivity. In optimised experimental conditions, the limits of detection for the 7 HAs studied ranged from 6 to 20 ng/L. Swimming pools have recently been recognized as an important source of exposure to DBPs and as a result, in this research for the first time, HAs have been determined in this type of water. Two HAs have been found in the analysed water: CH at concentrations between 1.2-38 and 53-340 μg/L and dichloroacetaldehyde between 0.07-4.0 and 1.8-23 μg/L in tap and swimming pool waters, respectively.     

Multipesticide residue analysis in maize combining acetonitrile-based extraction with dispersive liquid-liquid microextraction followed by gas chromatography-mass spectrometry

A fast and simple gas chromatography-mass spectrometry (GC-MS) method for determination of forty-one pesticide residues in maize is introduced. The sample preparation involves liquid-liquid partitioning with acetonitrile in presence of anhydrous MgSO(4) and NaCl (QuEChERS) followed by dispersive liquid-liquid microextraction (DLLME) using carbon tetrachloride as extractive solvent and the extract obtained by QuEChERS as dispersive solvent. The main factors influencing DLLME efficiency including extractive solvent type and volume as well as the volume of dispersive solvent were evaluated in this study. The DLLME procedure effectively provides an enrichment of the extract and a cleanup of certain polar matrix components, which can maximize the sensitivity when a single quadrupole MS is used. For validation purposes, recoveries studies were carried out at two concentration levels, yielding recovery rates in the range 70-120% for 82% of the analytes. A good linearity and precision, with relative standard deviations generally below 20% were obtained for all forty-one pesticides. The limits of detection obtained were lower than 19 μg kg(-1) for more than 63% of the analytes. In two of a total of ten samples of maize, residues of lindane, tefluthrin, pirimicarb, folpet and bifenthrin were found, although at levels below the maximum limit established for this kind of samples.     

Full-range analysis of ambient volatile organic compounds by a new trapping method and gas chromatography/mass spectrometry

This study investigated the feasibility of analyzing a full range of ambient volatile organic compounds (VOCs) from C(3) to C(12) using gas chromatograph mass spectrometry (GC/MS) coupled with thermal desorption. Two columns were used: a PLOT column separated compounds lighter than C(6) and a DB-1 column separated C(6)-C(12) compounds. An innovative heart-cut technique based on the Deans switch was configured to combine the two column outflows at the ends of the columns before entering the MS. To prevent the resolved peaks from re-converging after combining, two techniques were attempted (hold-up vs. back-flush) to achieve the intended "delayed" elution of heavier components. Thus, the resulting chromatogram covering the full range of VOCs is a combination of two separate elutions, with the heavier section following the lighter section. With the hold-up method, band-broadening inevitably occurred for the delayed C(6)-C(7) DB-1 compounds while the light compounds eluted from the PLOT column. This broadening problem resulted in peak tailing that was largely alleviated by adding a re-focusing stage while the DB-1 compounds were back-flushed, and this modified technique is referred to as the back-flush method. With this modification, the separation of the C(6)-C(7) compounds improved dramatically, as revealed by the decrease in peak asymmetry (As) and increase in resolution. Linearity and precision for these peaks also improved, yielding R(2) and RSD values better than 0.9990 and 2.8%, respectively.     

Determination of cyclic and linear siloxanes in soil samples by ultrasonic-assisted extraction and gas chromatography-mass spectrometry

A rapid method, based on sonication-assisted extraction in small columns (SAESC) and subsequent quantification and identification by gas chromatography-mass spectrometry (GC-MS), was developed for the determination of cyclic and linear siloxanes in soil. In the experiments with spiked samples (10-50 ng g(-1)), the recovery of cyclic and linear siloxanes ranged from 87.7 to 108.0% and from 84.9 to 107.6%, respectively. The validated method was used to determine the levels of these compounds in various types of soil samples collected from different locations in Spain. The cyclic siloxanes, decamethylcyclopentasiloxane (D5) and dodecamethylcyclohexasiloxane (D6) were detected in all the soil samples analyzed at concentrations from 9.2 to 56.9 ng g(-1) for D5 and from 5.8 to 27.1 ng g(-1) for D6 in agricultural soils and from 22 to 184 ng g(-1) for D5 and from 28 to 483 ng g(-1) for D6 in industrial soils. The total linear siloxanes concentrations (L5-L14) (sum of the 10 congeners) ranged from 191 to 292 ng g(-1) in agricultural soils and from 1411 to 8532 ng g(-1) in industrial soils.     

A retention time locked gas chromatography-mass spectrometry method based on stir-bar sorptive extraction and thermal desorption for automated determination of synthetic musk fragrances in natural and wastewaters

A stir-bar sorptive extraction (SBSE) method followed by automated thermal desorption (ATD) coupled to gas chromatography-mass spectrometry was optimized for determining trace levels of 18 synthetic fragrances (musks). Using the method developed a retention time locked library is created and converted to a screening database. This homebuilt database can be combined with deconvolution software for the identification of musks. A factorial design was provide to evaluate the main parameters and interactions between the factors affecting the process of SBSE. Operating with de MS-detector in the full-scan mode, high sensitivity with detection limits in the low ng L(-1) range, and good linearity and repeatability were achieved for all musks. The applicability of the method developed was tested in natural waters (surface and groundwater) and wastewater of a plant treatment (WWPT). The results obtained confirmed the usefulness of the proposed method for the determination and unequivocal identification of musks. This approach enables the developed method to be used for routine screening of environmental samples and posterior rapid quantitation of the positive samples.     

The role of the acquisition methods in the analysis of natural and synthetic steroids and cholic acids by gas chromatography-mass spectrometry

An exhaustive GC-MS acquisition study was performed, for the simultaneous analysis of natural and synthetic steroids and cholic acids (in order to insert them into the last tierce of our multiresidue analysis system), such as androsterone, β-estradiol, transdehydroandro-sterone, transdehyroandrosterone, mestranol, dihydrotestosterone, ethinylestradiol, testosterone, norethisterone, estriol, 4-androstene-3,17-dione, gestodene, levonorgestrel, etonogestrel, coprostanol, progesterone, cholesterol, medroxyprogesterone-acetate, lithocholic acid, stigmasterol, cholic acid, chenodeoxycholic acid, β-sitosterol, ursodeoxycholic acid, 3-hydroxy-7-ketocholic acid and dehydrocholic acid, in total 26 compounds. As novelties to the field, for the trimethylsilyl (TMS) oxime ether/ester derivatives of steroids and cholic acids, at first, a tandem mass spectrometric (MS/MS), multiple reaction monitoring (MRM) type acquisition method has been developed in a single run; also for the first time, the three acquisition techniques, the full scan (FS), the selective ion monitoring (SIM), in our case the multiple ion monitoring (MIM) and the currently optimized MRM methods, have been compared; all three, in parallel, under strictly the same derivatization/instrumental conditions, both in matrix free solutions and municipal wastewater from two Hungarian wastewater treatment plants (WWTPs). Critical evaluation of the three acquisition protocols was collated on their analytical performances and validated under the same conditions. The data of six point calibration curves for FS, MIM and MRM methods, showed that both R2 (0.9995, 0.9858, 0.9975) and RSD (5.3, 5.8, 5.0), for two parallel derivatizations, each injected three times, proved to be independent of the acquisition processes. Whereas, for the method limit of quantification (LOQ) and the instrument limit of quantification (ILQ) values showed considerable differences. LOQ data, were decreasing in the FS, MIM, MRM line (expressed in ng/L), for all steroids and cholic acids. The same trend was determined in terms of the ILQ values. The practical utility of the optimized acquisition techniques was confirmed by the quantitation of the steroids and cholic acids contents of wastewater samples. Results confirmed the importance of the MRM acquisition method, even in comparison to the MIM one: with particular interest in selected cases: avoiding the extreme overestimation of the β-estradiol (156-1325%) and that of the ethinylestradiol (582-831%) concentrations in the wastewater samples.     

Preparation of phenothiazine bonded silica gel as sorbents of solid phase extraction and their application for determination of nitrobenzene compounds in environmental water by gas chromatography-mass spectrometry

In this paper, two phenothiazine bonded silica (PTZ-Si) sorbents were prepared and used as sorbents of solid-phase extraction (SPE) for the determination of nitrobenzene compounds in environmental water samples by gas chromatography-mass spectrometry (GC-MS). Different synthesis routes were proposed to obtain high bonded amount of PTZ on the surface of silica gel. PTZ molecule was derived to its amino or acyl chloride derivatives for reacting with isocyanate or amino silane coupling agent, which was further reacted with the surface silanol groups of silica gel to obtain the PTZ-Si sorbents. The resultant PTZ-Si sorbents were characterized by nitrogen sorption porosimetry (NSP), Fourier transform infrared spectroscopy (FT-IR) and elemental analysis (EA) to assure the successful bonding of PTZ on the surface of silica gel. Then the PTZ-Si sorbents were served as SPE sorbents for the enrichment of nitrobenzene compounds. Several parameters affecting the extraction performance were investigated. Under the optimized conditions, the proposed method was applied to the analysis of six nitrobenzene compounds in environmental water samples. Good linearities were obtained for all nitrobenzene compounds with R(2) larger than 0.9958. The limits of detection were found to be in the range of 0.06-0.3 ng/mL. The method recoveries of nitrobenzene compounds spiked in water samples were from 71.4% to 124.3%, with relative standard deviations (RSDs) less than 10.1%.     

Simultaneous determination of benzotriazoles and ultraviolet filters in ground water, effluent and biosolid samples using gas chromatography-tandem mass spectrometry

A new method using gas chromatography-tandem mass spectrometry (GC-MS/MS) was developed for the determination of four benzotriazoles, i.e. benzotriazole (BT), 5-methylbenzotriazole (5-TTri), 5-chlorobenzotriazole (CBT), 5,6-dimethylbenzotriazole (XTri), and six UV filters, i.e. benzophenone-3 (BP-3), 3-(4-methylbenzylidene)camphor (4-MBC), octyl 4-methoxycinnamate (OMC), 2-(3-t-butyl-2-hydroxy-5-methylphenyl)-5-chloro benzotriazole (UV-326), 2-(2'-hydroxy-5'-octylphenyl)-benzotriazole (UV-329), and octocrylene (OC) in ground water, effluent and biosolid samples. Solid phase extraction (SPE) and pressurized liquid extraction (PLE) were applied as the preconcentration method for water samples (ground water and effluent) and biosolid samples, respectively. The optimized method allowed us to quantify all target compounds with the method detection limits ranging from 0.29 to 11.02 ng/L, 0.5 to 14.1 ng/L and 0.33 to 8.23 ng/g in tap water, effluent and biosolid samples, respectively. The recoveries of the target analytes in tap water, effluent and biosolid samples were 70-150%, 82-127% and 81-133%, respectively. The developed analytical method was applied in the determination of these target compounds in ground water, effluent and biosolid samples collected from Bolivar sewage treatment plants in South Australia. In effluent samples, the target compounds BT, 5-TTri, CBT, XTri and BP-3 tested were detected with the maximum concentration up to 2.2 μg/L for BT. In biosolid samples, eight out of ten compounds tested were found to be present at the concentrations ranging between 18.7 ng/g (5-TTri) and 250 ng/g (4-MBC).     

Quantitative analysis of fatty-acid-based biofuels produced by wild-type and genetically engineered cyanobacteria by gas chromatography-mass spectrometry

Simple and rapid quantitative determination of fatty-acid-based biofuels is greatly important for the study of genetic engineering progress for biofuels production by microalgae. Ideal biofuels produced from biological systems should be chemically similar to petroleum, like fatty-acid-based molecules including free fatty acids, fatty acid methyl esters, fatty acid ethyl esters, fatty alcohols and fatty alkanes. This study founded a gas chromatography-mass spectrometry (GC-MS) method for simultaneous quantification of seven free fatty acids, nine fatty acid methyl esters, five fatty acid ethyl esters, five fatty alcohols and three fatty alkanes produced by wild-type Synechocystis PCC 6803 and its genetically engineered strain. Data obtained from GC-MS analyses were quantified using internal standard peak area comparisons. The linearity, limit of detection (LOD) and precision (RSD) of the method were evaluated. The results demonstrated that fatty-acid-based biofuels can be directly determined by GC-MS without derivation. Therefore, rapid and reliable quantitative analysis of fatty-acid-based biofuels produced by wild-type and genetically engineered cyanobacteria can be achieved using the GC-MS method founded in this work.     

Determination of chloropropanols in foods by one-step extraction and derivatization using pressurized liquid extraction and gas chromatography-mass spectrometry

3-Chloropropane-1,2-diol (3-MCPD) and 1,3-dichloro-2-propanol (1,3-DCP) were determined for the first time in bakery foods using pressurized liquid extraction (PLE) combined with in situ derivatization and GC-MS analysis. This one-step protocol uses N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) as silylation reagent. Initially, screening experimental design was applied to evaluate the effects of the variables potentially affecting the extraction process, namely extraction time (min) and temperature (°C), number of cycles, dispersant reagent (diatomaceous earth in powder form and as particulate matter with high pore volume Extrelut NT) and percent of flush ethyl acetate volume (%). To reduce the time of analysis and improve the sensitivity, derivatization of the compounds was performed in the cell extraction. Conditions, such as the volume of BSTFA, temperature and time for the in situ derivatization of analytes using PLE, were optimized by a screening design followed to a Doehlert response surface design. The effect of the in-cell dispersants/adsorbents with diatomaceous earth, Florisil and sodium sulfate anhydrous was investigated using a Box-Behnken design. Using the final best conditions, 1 g of sample dispersed with 0.1 g of sodium sulfate anhydrous and 2.5 g diatomaceous earth was extracted with ethyl acetate. 1 g of Florisil, as clean-up adsorbent, and 70 μL of BSTFA were used for 3 min at 70°C. Under the optimum conditions, the calibration curves showed good linearity (R(2)>0.9994) and precision (relative standard deviation, RSD≤2.4%) within the tested ranges. The limits of quantification for 1,3-DCP and 3-MCDP, 1.6 and 1.7 μg kg(-1), respectively, are far below the established limits in the European and American legislations. The accuracy, precision, linearity, and limits of quantification provided make this analytical method suitable for routine control. The method was applied to the analysis of several toasted bread, snacks, cookies and cereal samples, none of which contained chloropropanols at concentrations above the legislation levels.     

Determination of suspected fragrance allergens in cosmetics by matrix solid-phase dispersion gas chromatography-mass spectrometry analysis

An effective low cost sample preparation methodology for the determination of regulated fragrance allergens in leave-on and rinse-off cosmetics has been developed applying, for the first time, matrix solid-phase dispersion (MSPD) to this kind of analytes and samples. The selection of the most suitable extraction conditions was made using statistical tools such as ANOVA, as well as a factorial multifactor experimental design. These studies were carried out using real cosmetic samples. In the final conditions, 0.5 of sample, previously mixed with 1g of anhydrous Na(2)SO(4), were blended with 2g of dispersive sorbent (Florisil), and the MSPD column was eluted with 5 mL of hexane/acetone (1:1). The extract was then analyzed by GC-MS without any further clean-up or concentration step. Accuracy, precision, linearity and detection limits (LODs) were evaluated to assess the performance of the proposed method. Quantitative recoveries (>75%) were obtained and RSD values were lower than 10% in all cases. The quantification limits were well below those set by the international cosmetic regulations, making this multi-component analytical method suitable for routine control. In addition, the MSPD method can be implemented in any laboratory at low cost since it does not require special equipment. Finally, a wide variety of cosmetic products were analyzed. All the samples contained several of the target cosmetic ingredients, with and average number of seven. The total fragrance allergen content was in general quite high, even in baby care products, with values close to or up to 1%, for several samples, although the actual European Cosmetic Regulation was fulfilled.     

A liquid chromatography-mass spectrometry assay method for simultaneous determination of amiodarone and desethylamiodarone in rat specimens

A liquid chromatographic-mass spectrometry (LC/MS) assay method was developed for the determination of amiodarone and desethylamiodarone in rat specimens. Analytes were extracted using liquid-liquid extraction in hexane. The LC/MS system consisted of a Waters Micromass ZQtrade mark 4000 spectrometer with an autosampler and pump. A C(18) 3.5 microm (2.1 x 50 mm) column heated to 45 degrees C was used for separation. The mobile phase consisted of methanol and 0.2% aqueous formic acid pumped at 0.2 mL/min as a linear gradient. Components eluted within 12 min. The concentrations of ethopropazine (internal standard), desethylamiodarone and amiodarone were monitored for m/z of 313.10, combination of 546.9 and 617.73, and 645.83, respectively. In plasma (0.1 mL), linearity was achieved between the peak area ratios and concentrations over the range of 2.5-1000 ng/mL for both amiodarone and desethylamiodarone (r(2) > 0.999). The intraday and interday CV were equal or less than 18%, and mean error was <12%. Similarly, in homogenates containing 0.1 g of rat tissue, linearity was observed in standards ranging from 5 to 5000 ng/g. The method was successfully used to measure tissue and plasma concentrations of drug. The validated lower limit of quantitation was 2.5 ng/mL for drug and metabolite, based on 0.1 mL of plasma.     

Determination of 195 pesticide residues in Chinese herbs by gas chromatography-mass spectrometry using analyte protectants

The phenomenon known as "matrix-induced enhancement effect" is not only observed in the analysis of pesticides in food, but also in Chinese herbs. Several approaches have been proposed to overcome the matrix-induced effect, but each method has serious limitations. Compared with standard calibration methods, the procedure with adding analyte protectants offers a more convenient and effective route to solve the problem. In the current study, we have analyzed 195 types of pesticides in Chinese herbs by gas chromatography-mass spectrometry (GC-MS), and the compounds that are susceptible to matrix effect were picked up and confirmed. In addition, several analyte protectants were evaluated and the most effective combination was determined. D-ribonic acid-γ-lactone (2 mg/ml) and D-sorbitol (1 mg/ml) were shown to be the best analyte protectants for the analysis of most pesticides.     

Combined solid-phase extraction and gas chromatography-mass spectrometry used for determination of chloropropanols in water

A sensitive and rapid derivatization method for the simultaneous determination of 1,3-dichloro-2-propanol (1,3-DCP) and 3-chloropropane-1,2-diol (3-MCPD) in water samples has been developed. The aim was to research the optimal conditions of the derivatization process for two selected reagents. A central composite design was used to determine the influence of derivatization time, derivatization temperature and reagent volume. A global desirability function was applied for multi-response optimization. The analysis was performed by gas chromatography-mass spectrometry. During the optimization of the extraction procedure, four different types of solid-phase extraction (SPE) columns were tested. It was demonstrated that the Oasis HLB cartridge produced the best recoveries of the target analytes. The pH value and the salinity were investigated using a Doehlert design. The best results for the SPE of both analytes were obtained with 1.5 g of NaCl and pH 6. The proposed method provides high sensitivity, good linearity (R(2)≥0.999) and repeatability (relative standard deviations % between 2.9 and 3.4%). Limits of detection and quantification were in the range of 1.4-11.2 ng/mL and 4.8-34.5 ng/mL, respectively. Recoveries obtained for water samples were ca. 100% for 1,3-DCP and 3-MCPD. The method has been successfully applied to the analysis of different samples including commercially bottled water, an influent and effluent sewage.     

Application of solid-phase microextraction and gas chromatography-mass spectrometry for the determination of chlorophenols in leather

This paper proposes a new analytical procedure based on the headspace solid‐phase microextraction (HS‐SPME) technique and gas chromatography‐selected ion monitoring‐mass spectrometry (GC‐SIM‐MS) for the determination of 16 phenols extracted from leather samples. The optimized conditions for the HS‐SPME were obtained through two experimental designs – a two‐level fractional factorial design followed by a central composite design – using the commercial SPME fiber polyacrylate 85 μm (PA). The best extraction conditions were as follows: 200 μL of derivatizing agent (acetic anhydride), 20 mL of saturated aqueous NaCl solution and extraction time and temperature of 50 min and 75°C, respectively. All optimized conditions were obtained with fixed leather sample mass (250 mg), vial volume (40 mL) and phosphate buffer pH (12) and concentration (50 mmol/L). Detection limits ranging from 0.03 to 0.20 ng/g, and relative standard deviation (RSD) lower than 10.23% (n=6) for a concentration of 800 ng/g (chlorophenols) and 1325 ng/g (2‐phenylphenol) in the splitless mode were obtained. The recovery was studied at three concentration levels by adding different amounts of phenols to the leather sample and excellent recoveries ranging from 90.0 to 107.2% were obtained. The validated method was shown to be suitable for the quantification of phenols in leather samples, as it is simple, relatively fast and sensitive.