溶剂热合成纳米球状La2O2S：Eu^3＋荧光粉

Nano-sphere-like Eu^3 activated lanthanum oxysulfide phosphor was first synthesized directly by solvothermal method. The phosphor was characterized by XRD, TEM and PL. Photoluminescence spectra indicate that this phosphor showed three typical transitions of Eu^3 (^5Do→^7F^1,^5D0→^7F2,^5D0→^7F4). In comparison with those prepared by high temperature solid state method, photoluminescence spectrum of Eu^3 (^5D0→^7F2)-doped nano-La2O2S：Eu^3 phosphor became broader. And the reaction mechanism was also mentioned in this paper.     

Eu3+在La2O2S中的长余辉发光

The new Eu³⁺ doped lanthanum oxysulfide phosphors,which have the orange-red long afterg low emission,were synthesized by solid-state reaction method.The synthesized phosphors were characterized by X-ray diffraction.The excitation and emission spectra,afterglow spectra and afterglow decay curves were examined.XRD confirmed the phosphor as pure phase La₂O₂S.The phosphors showed typical transitions ⁵D_J(J=0,1) → ⁷J_J(J=0,1,2,3,4)of Eu³⁺.The photoluminescence spectra and afterglow spectra presented the regular alteration with various Eu³⁺ concentration, due to cross relaxation between energy levels of Eu³⁺. In addition, we studied the effects of activator concentration and dopants species on the afterglow property. The data showed afterglow result was the best with 2 % Eu³⁺ and doped with Mg²⁺ and Zr⁴⁺. A prominent phosphorescence can be seen in this phosphor after illuminated with UV light.     

La2O2S∶Mn2+荧光粉的微波合成及其荧光特性

Using La₂(SO₄)3 and the active carbon powder as reactants, La₂O₂S∶Mn²⁺ red phosphor was synthesized by microwave radiation method. The phosphor was characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), laser-diffraction size analyzer and fluorospectrophotometer. The XRD analysis showed that the phosphor was pure phase La₂O₂S. The phosphor of La₂O₂S∶Mn²⁺ showed hexagonal crystal structure with diverse shapes, such as spherical and rod, with average particle size of 10.22 μm. The emission and excitation spectra of the phosphor were determined by fluorospectrophotometer and the results showed that the excitation spectrum of the phosphor under 600 nm emission wavelength was excitation bands between 250 nm and 350 nm with a peak value of 303 nm. Then ,when exicited under UV 303 nm, the phosphor showed broad band emission of 550~700 nm with a peak at 607 nm. In addition, the optimal effects were obtained for the phosphor preparation when the concentration of the activator Mn²⁺ was x_Mn=0.01, the ratio of C and O (n_C / n_O) in the reactants was 0.6∶1, and the time of reaction was about 1 h. La₂O₂S∶Mn²⁺ has strong absorption of UV spectrum and can emit bright red light.     

KMgF3∶Ce3+，Eu2+的溶剂热合成与光谱性质

采用溶剂热法合成了Eu2 ,Ce3 单掺和双掺KMgF3.分析了样品的结构与形貌.结果表明,所合成的样品均为单相,颗粒粒度分布集中.测定了它们的激发和发射光谱,结果显示:在单掺Eu2 的KMgF3中,没有观察到位于420nm附近由微量氧色心引起的宽带发射,只发现峰值位于360 nm附近的锐峰线发射,说明溶剂热合成的KMgF3:Eu中氧含量极低;在KMgF3双掺体系中由于Eu2 和Ce3 争吸收激发能,Eu2 把能量传递给Ce3 ,存在Eu2 -Ce3 能量传递过程.观察到Ce3 的较强的发射带和Eu2 的较弱的线发射,并讨论了能量传递机理.     

溶剂热合成具有纳米孔结构的γ -Al2O3

Nanoporous gamma aluminum oxide (γ-Al₂O₃) was synthesized by solvothermal method in the presence of AlCl₃·6H₂O, urea and alcohol. The calcined sample was characterized by XRD, FTIR, TEM, and Nitrogen adsorption-desorption measurement. Results show that the obtained γ-Al₂O₃ is well-dispersed nanoparticles with particle size of 4～7 nm and the product has nano-pore structure with a narrow pore size distribution of 5～20 nm.     

链状[NH3CH2CH2NH3]AgAsS4的溶剂热合成及表征

利用溶剂热方法合成了链状[NH3CH2CH2NH3]AgAsS4,通过单晶X射线衍射技术对其进行了晶体结构分析,该化合物晶体属单斜晶系,空间群C2/c,晶胞参数a=1.35805(8)nm,b=0.65331(3)nm,c=2.27711(9)nm,β=106.42(3)°,Z=8.化合物具有有趣的梯子状双链结构,该阴离子链由AsS4与AgS3共用顶点交替连接而成,有机阳离子在阴离子链之间存在较强的N—H…S氢键.DSC和Tg分析结果表明化合物在200℃以下是稳定的.     

水热-微波法合成纳米晶长余辉发光材料Y2O2S∶Eu3+，Mg，Ti

采用新型水热-微波法合成了纳米晶长余辉发光材料Y₂O₂S∶Eu³⁺,Mg,Ti。通过XRD、TEM、荧光光谱对其进行表征。X射线衍射测试表明所制备的Y₂O₂S∶Eu³⁺,Mg,Ti纳米发光材料为单相,六方晶。透射电子显微镜(TEM)测试表明所制备的Y₂O₂S∶Eu³⁺,Mg,Ti纳米发光材料粒径小,分布集中。激发和发射光谱测试表明Eu³⁺离子能有效地掺入硫氧化钇基质中,并具有良好的发光性能。余辉光谱测试表明其余辉颜色为红色,具有良好的余辉效果。     

热处理温度对溶剂热合成Co3O4纳米片气敏和吸附性能之影响

以Co（Ac）₂·4H₂O和六次甲基四胺（HMTA）为起始反应物,聚氧乙烯-聚氧丙烯-聚氧乙烯（P123）为表面活性剂,在乙二醇（EG）和水混合溶剂中用溶剂热法得到中间产物,通过煅烧热处理制备了Co₃O₄纳米片。利用XRD、SEM和N₂吸附-脱附等方法进行了样品表征,研究了不同热处理温度对产物形貌和结晶度的影响,以及所制备纳米片的气敏性能。根据气敏测试和吸附性能结果,分析了气敏机理和吸附动力学。结果表明：热处理温度是影响产物形貌的关键因素,350℃是最佳的热处理温度,此时得到的纳米片最薄也最均匀。由于产物形貌变化改变了材料的比表面积,进而影响到产物的气敏性能和吸附性能。总体而言,纳米片厚度越小,比表面面积越大,材料的气敏灵敏度和吸附效率越高。     

热处理温度对溶剂热合成Co3O4纳米片气敏和吸附性能之影响

以Co(Ac)2·4H_2O和六次甲基四胺(HMTA)为起始反应物,聚氧乙烯-聚氧丙烯-聚氧乙烯(P123)为表面活性剂,在乙二醇(EG)和水混合溶剂中用溶剂热法得到中间产物,通过煅烧热处理制备了Co_3O_4纳米片。利用XRD、SEM和N_2吸附-脱附等方法进行了样品表征,研究了不同热处理温度对产物形貌和结晶度的影响,以及所制备纳米片的气敏性能。根据气敏测试和吸附性能结果,分析了气敏机理和吸附动力学。结果表明:热处理温度是影响产物形貌的关键因素,350℃是最佳的热处理温度,此时得到的纳米片最薄也最均匀。由于产物形貌变化改变了材料的比表面积,进而影响到产物的气敏性能和吸附性能。总体而言,纳米片厚度越小,比表面积越大,材料的气敏灵敏度和吸附效率越高。     

溶剂热还原合成Cr2O3纳米管(英)

Cr₂O₃ nanotubes with diameters of 80 nm and lengths of 550 nm were synthesized in a solvothermal reduction system at 180 ℃. The acetyl acetone (AcAc) and ethylene glycol (EG) were used as the chelate agent and the reductant respectively in the system. An intermediate compound-Cr(Ⅲ)(C₅H₇O₂)₃ was formed to force Cr₂O₃to crystallize along one direction.     

KSrBP2O8:RE(RE=Eu2+,Tb3+,Eu3+)荧光粉的制备与发光性能研究

采用高温固相反应法制备了KSrBP2O8:RE(RE=Eu2+,Tb3+,Eu3+)系列荧光粉。利用X射线衍射仪对样品的物相结构进行了分析,结果表明:稀土离子的掺入没有改变荧光粉的主晶相。利用荧光光谱仪对样品的发光性能进行了测试,发现在近紫外光激发下掺杂Eu2+离子的样品具有宽带发射峰,最强发射位于450 nm左右,对应于Eu2+离子的4f65d1→4f7辐射跃迁。随着Eu2+掺杂量的增加,发射光从蓝光逐渐转变到蓝白光。另外,KSrBP2O8:Tb3+和KSrBP2O8:Eu3+能够在近紫外光激发下分别发射出绿光和红光,其最佳掺杂浓度分别为0.04%和0.08%(摩尔分数)。     

K2CdSnS4的溶剂热合成与晶体结构

利用溶剂热法合成了层状硫代锡(Ⅲ)酸镉(Ⅱ)化合物K₂CdSnS₄。单晶X-射线衍射分析结果表明,化合物属单斜晶系,C2/c空间群,a=1.1021(5)nm,b=1.1030(5)nm,c=1.5151(10)nm,α=90°,β=100.416(12)°,γ=90°,V=1.8114(17)nm³,Z=8,D_c=3.209g·cm^-3,M_r=437.60,μ=6.853mm^-1,F(000)=1600,λ=0.071073nm,R=0.1042,wR=0.2008。该化合物由类金刚烷[Cd₂Sn₂S₁₀]^8-结构单元互相连接形成层状结构。紫外-可见漫反射光谱研究表明,化合物为半导体,带隙为2.2eV。     

溶剂热-热解法制备具有纳米孔结构的Co3O4

Nanoporous rhombohedral Co₃O₄ was synthesized by thermal decomposition of the precursor obtained via a solvothermal method in the presence of Co(CH₃COO)₂·4H₂O, urea, sodium dodecyl sulfate (SDS), ethanol and water. The calcined sample was characterized by XRD, FTIR, SEM, TG-DTA, Nitrogen adsorption-desorption, cyclic voltammetry and galvanostatic charge/discharge measurements. The results show that the calcined sample at 400 ℃ is rhombohedral structure Co₃O₄ with nano-porosity assembled by uniform nanosheets. The BET surface area is 49 m²·g^-1 and its specific capacitance as single electrode is up to 233.4 F·g^-1 at 5 mA·cm^-2 current density.     

溶剂热合成三维蔷薇花状SnS2微晶

在乙二醇溶剂热条件下,采用SnCl4·H2O和硫代氨基脲为原料,成功制备出了三维蔷薇花状的SnS2微晶.产品用X-射线粉末衍射(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、拉曼光谱(RS)和紫外一可见吸收光谱(UV-Vis)对样品进行了表征.结果表明SnS2蔷薇花是由纳米级厚度的片状"花瓣"相互连接、交叠、缠绕自组装生长而成.并对蔷薇花状SnS2三维结构的生长机理进行了简单探讨.     

Ce3+掺杂La2O3的17O固体核磁共振研究

本文用水热共沉淀法制备Ce³⁺掺杂La₂O₃的前驱体,随后在H₂/N₂气氛下用高温煅烧法合成了不同Ce³⁺浓度的掺杂La₂O₃。由于Ce³⁺的掺杂,¹⁷O固体核磁共振谱图中在698、650和558处出现了新的共振峰;随着Ce³⁺掺杂浓度的增加,这些峰的强度也随之增强。根据谱峰位置和强度,对谱图进行了归属:698、650处的共振峰应源自与Ce³⁺相连的四配位O(OCeLa₃),558处的信号则来自于与Ce³⁺相连的六配位O(OCeLa₅)。通过¹⁷O固体核磁共振能够直接观测与Ce³⁺直接相连的O显示该方法将可能用于研究稀土掺杂氧化物功能材料。     

Y2O2S∶Eu3+空心微球的制备与性能

以单分散的碳球为硬模板,采用均匀共沉淀法合成了Y2O2S:Eu3+心微球.通过XRD、SEM、TEM、荧光光谱对其进行表征.X射线衍射测试表明所制备的Y2O2S:Eu3+空心微球为单相,六方晶.扫描电子显微镜(SEM)和透射电子显微镜(TEM)测试表明所制备的Y2O2S:Eu3+空心微球粒径小,分布均匀.激发和发射光谱测试表明Eu3+离子能有效地掺入硫氧化钇基质中,并具有良好的发光性能.     

NaY(WO4)2∶Eu3+/Tb3+/Tm3+白色荧光粉的制备与发光性能

采用溶剂热法合成了一种单一相白色荧光粉NaY(WO4)2∶Eu3+,Tb3+,Tm3+。通过X射线衍射(XRD)、扫描电镜(SEM)、X射线能谱(EDS)及荧光光谱(PL)对制备的系列样品的物相、形貌和荧光性质进行了表征。结果表明:在荧光粉NaY(WO4)2∶x%Eu3+,4%Tb3+,1%Tm3+(x=5,10,15,20)中,随着Eu3+掺入量的增加,发光从绿光区进入白光区。同时观察到Tb3+到Eu3+的有效能量传递。     

溶剂热法合成ZnSe纳米球

以乙酸锌和Se粉为原料,环己酮为溶剂,于180 ℃反应24 h制得黄色纳米球ZnSe,其结构和性能经XRD,SEM及TEM表征.     

稀土红色荧光粉SrZnO2∶Eu3+的发光性能

A series of novel luminescent materials, SrZnO₂∶M (M=Eu³⁺, or Eu³⁺ + Li⁺) have been synthesized by high-temperature solid-state reaction. The structure and luminescence properties of SrZnO₂∶Eu³⁺ phosphor were studied through XRD, photoluminescence and Raman spectroscopy. The excitation spectra show a broad intense band and a number of small peaks corresponding to the inner 4f-shell excitations of Eu³⁺ (the strongest one is at 395 nm for ⁷F₀-⁵L₆). After SrZnO₂∶Eu³⁺ phosphor was co-doped with Li⁺ ions, its charge transfer band extended to longer wavelengths. This resulted in increase of luminescent quantum efficiency of the sample. SrZnO₂∶Eu³⁺,Li⁺ phosphor can be efficiently excited by longer UV. From the fluorescence spectrum of SrZnO₂∶Eu³⁺ phosphor, apart from transition emissions of ⁵D₀→ ⁷F_J (J=0～4), the transition emissions from ⁵D₁ → ⁷F_J (J=0～2) have been observed. For the SrZnO₂∶Eu³⁺ phosphor, under excitation of UV, the dominant emission is at about 612 nm, due to the ⁵D₀→ ⁷F₂ hypersensitive transition. The incorporation of Li⁺ ions greatly enhanced the luminescence intensity and made emission peak from ⁵D₀ → ⁷F₂ transition red-shifted.     

非晶红色荧光粉Cd3Al2Si3O12∶Eu3+的制备及发光性能

使用溶胶-凝胶法制备了Cd₃Al₂Si₃O₁₂∶Eu³⁺非晶体系红色荧光粉,并对其发光性质进行了研究。该荧光粉在Eu³⁺的位于394 nm的⁵L₆能级和464 nm的⁵D₂能级的激发下能够产生强的⁵D₀→⁷F₂的红光特征发光,最佳掺杂摩尔分数为25%。Cd₃Al₂Si₃O₁₂∶Eu³⁺荧光粉与传统的Y₂O₃∶Eu³⁺相比较,其发光强度是Y₂O₃∶Eu³⁺的2.4倍左右(在394和464 nm的激发下)。Cd₃Al₂Si₃O₁₂∶Eu³⁺的热稳定性好,比已经商业化的YAG∶Ce³⁺的热猝灭影响要小得多。所有这些结果表明Cd₃Al₂Si₃O₁₂∶Eu³⁺可作为暖白光LED用红色荧光粉。