Theory and application of cyclic voltammetry at a hemispherical microelectrode for a quasi-reversible reaction

The theory of cyclic voltammetry for a quasi-reversible reaction at a hemispherical microelectrode has been deduced. From the results calculated according to the theory, the heterogeneous rate constant and charge transfer coefficient can be measured with the cyclic voltammetric data obtained at an intermediate scan rate on a hemispherical microelectrode. To verify the theory, the kinetic constant for reduction of benzoquinone in acetonitrile has been determined. The result is coincident with that measured by a fast scan rate at a platinum microdisk electrode. The kinetic constant and charge transfer coefficient for reduction of 2,3,5,6-tetrachlorobenzoquinone have also been determined with the method described in this paper.     

A novel method for fast determination of vitamin B6 by fast continuous cyclic voltammetry

In this work a novel method for the determination of Vitamin B6 in flow-injection systems has been developed. The fast Fourier transform continuous cyclic voltammetry (FFTCV) at gold microelectrode in flowing solution system was used for determination of Vitamin B6. This method is rapid, simple and highly sensitive procedures allowing the determination of Vitamin B6 in pharmaceutical analysis. The effects of various parameters on the sensitivity of the method were investigated. The best performance was obtained with the pH value of 2, scan rate value of 30 V/s, accumulation potential of 200 mV and accumulation time of 0.3 s. The proposed method has some advantages over other reported methods such as, no need for the removal of oxygen from the test solution, a sub-nanomolar detection limit, and finally the method is fast enough for the determination of any such compound, in a wide variety of chromatographic methods. To obtain a sensitive determination, the integration range of currents was set for all the potential scan ranges, including oxidation and reduction of the Au surface electrode, while performing the measurements. The potential waveform, consisting of the potential steps for cleaning, accumulation and potential ramp of analyte, was applied on an Au disk microelectrode (12.5 μm in radius) in a continuous way. The detection limit of the method for Vitamin B6 was 2.8 pg/ml. The relative standard deviation of the method at 2.1% was 8 runs. Published in Russian in Elektrokhimiya, 2008, Vol. 44, No. 2, pp. 173–181. The text was submitted by the authors in English.     

圆盘微电极的卷积和交流伏安行为

研究了可逆氧化还原对(以二茂铁为例)在圆盘微铂电极上的卷积法,包括一阶导数卷积(e),二阶导数卷积(e′),三阶导数卷积(e″)的行为.结果表明,在微电极上的 e-E曲线类似于常规电极的循环伏安曲线。e、e′和e″曲线的峰高与扫速幂次的关系与悬汞电极上的规律相符,但其值分别为0.5、1.5、2.5.还研究了微电极的交流伏安行为,得到铁氰化钾的特征电位值。     

Application of thin-shielded mercury microelectrodes in anodic stripping voltammetry

The performance in anodic stripping voltammetry (ASV) of hemispherical mercury microelectrodes, fabricated by electrodeposition of liquid mercury on the surface of Pt microdisks which were surrounded by a rather thick or thin insulating shield, was compared. The Pt microdisks were produced by sealing a wire of 25 μm diameter into a glass capillary, and by coating the cylindrical length of the Pt wire with a cathodic electrophoretic paint. The ratio of the overall tip radius b, to the basal radius of the electrode a, so-called RG = b/a, was equal to 110 ± 10 and 1.52 ± 0.01 for the thick- and thin-shielded microdisk, respectively. The mercury microelectrodes were characterized by cyclic voltammetry at 1 mV s⁻¹, in 1 mM Ru(NH₃)₆³⁺ aqueous solution. The steady-state voltammogram recorded with the thin-shielded mercury microelectrode displayed less hysteresis, while the steady-state current was about 30% higher than that of the thicker one. This was a consequence of the additional flux due to diffusion from behind the plane of the electrode. The flux enhancement, which was operative at the thin-shielded mercury microelectrode during the deposition step in the ASV experiments, allowed recording stripping peaks for Cd and Pb, which resulted about 32% larger than those recorded at the thicker shielded mercury microelectrode, under same experimental conditions.The usefulness of the thin-shielded mercury microelectrode for ASV measurements in real samples was verified by determining the content of heavy metal ions released in the pore water (pH 4.5) of a soil slurry.     

Study on the adsorptive catalytic voltammetry of aloe-emodin at a carbon paste electrode

Recently, the studies and applications for the pola-rographic catalytic waves of organic compounds at dropping mercury electrode made considerable head-way. Tovopova et al.[1―4] reported the polarographic catalytic waves of the organic compounds containi…     

Determination of arsenic by cathodic stripping voltammetry at a hanging mercury drop electrode

Arsenic (III), respectively arsenic(V) after the reduction were determined in model solutions and some inorganic and organic materials by fast scan differential pulse cathodic stripping voltammetry and by direct current cathodic stripping voltammetry with a rapid increase of potential. The accumulation on a hanging mercury drop electrode followed by cathodic stripping was carried out in 0.7–0.8M HCl or 1–2M H₂SO₄ solutions containing Cu(II)-ions. Detection limits calculated from regression parameters was determined to be under 1 ng/ml for the samples containing very low arsenic concentrations. The relative standard deviation did not reach 8% for arsenic contents about of 5 ng/ml.     

Differential linear scan voltammetry: analytical performance in comparison with pulsed voltammetry techniques

We report here on differential linear scan voltammetry, DLSV, that combines the working principles of linear scan voltammetry, LSV, and the numerous existing pulsed voltammetry techniques. DLSV preserves the information from continuous interrogation in voltage and high accuracy that LSV provides about electrochemical processes, and the much better sensitivity of differential pulsed techniques. DLSV also minimizes the background current compared to both LSV and pulsed voltammetry. An early version of DLSV, derivative stationary electrode polarography, DSEP, had been proposed in the 1960s but soon abandoned in favor of the emerging differential pulsed techniques. Relative to DSEP, DLSV takes advantage of the flexibility of discrete smoothing differentiation that was not available to early investigators. Also, DSEP had been explored in pure solutions and with reversible electrochemical reactions. DLSV is tested in this work in more challenging experimental contexts: the measurement of oxygen with a carbon fiber microelectrode in buffer, and with a gold microdisc electrode exposed to a live biological preparation. This work compares the analytical performance of DLSV and square wave voltammetry, the most popular pulsed voltammetry technique.

Study of electrochemical properties of pyrrolidinofullerenes by microelectrode voltammetry

The electrochemical behavior of nine pyrrolidinofullerenes has been investigated by cyclic voltammetry on a gold microdisk electrode. Four reversible reduction peaks and two irreversible reduction peaks are observed for each fullerene derivative. The half-wave potentials of all pyrrolidinofullerenes are more negative than those of C₆₀ itself. The diffusion coefficient of these compounds is measured by their steady-state voltammograms.     

Staircase voltammetry with finite diffusion space

A theory of the staircase voltammetry in a thin-layer cell is developed. The influence of the cell thickness and the redox reaction rate constant on the current and the peak potentials is analyzed. For moderately thick cells, the kinetic maximum is predicted. The relationship between peak currents and the square root of the scan rate is not linear and the response may entirely vanish if the redox reaction is fast, the cell is very thin and the scan rate is slow.     

电活化玻碳电极差分脉冲溶出伏安法测定磺胺嘧啶

采用线性循环溶出伏安法和差分脉冲溶出伏安法对磺胺嘧啶在电活化玻碳电极上的电化学行为进行了研究。玻碳电极在PBS溶液中(pH 7.0),用恒电位法在1.7 V阳极氧化400 s,在B-R缓冲溶液中,磺胺嘧啶在1.02V(vs.Ag/AgCl)处有一良好的氧化峰,在0.02～0.25 V/s范围内,其氧化峰电流与扫描速率呈良好线性关系,表明电极过程为受吸附控制的不可逆过程。差分脉冲溶出伏安法的氧化峰电流(Ipa)与磺胺嘧啶浓度1×10-6～1×10-4mol/L范围内呈良好的线性关系(r=0.9977),检出限为8.7×10-7mol/L(S/N=3)。方法已用于分析磺胺嘧啶片剂的分析。     

Theory and application of cyclic voltammetry for measurement of fast electrode kinetics at microdisk electrode

An analytical expression describing voltammetric behaviors responses at microdisk electrode for various diffusion conditions and degrees of reversibility is reported in this paper. Results of theoretical calculation made it possible to use cyclic voltammetry to evaluate heterogeneous rate constants under intermediate diffusion conditions. At relatively low scan rate, the distortion of current-voltage can be reduced due to small iR drops and charging current. The effects of transfer coefficient, a, kinetic parameter, (=k0r/4D), and switching potential, s, on potential peak separation are discussed in detail. The relationship obtained in this paper between potential peak separation and \ is in good agreement with that in Ref. 14, whose authors have got their results by using digital simulation technique. After the experiment of Fe(CN)64- oxidation, k0 and a were obtained by the theory of this paper. The result agrees with that in Ref. 19.     

Voltammetric Studies on the Electrochemical Reduction of Methylmercury in HCl Aqueous Medium at a Carbon Microelectrode

Fast scan voltammetry applied to methylmercury in chloride medium at a carbon fiber microelectrode has shown two cathodic peaks located at ?0.45 and ?1.1 V and a single anodic peak at ?0.33 V (vs. Ag|AgCl). It was concluded that the reoxidation process, at high sweep rates, in acidic media behaves as a reversible one‐electron transfer process coupled to a chemical reaction, with the reaction product weakly adsorbed. Good linear calibration plots for the methylmercury determinations in the concentration range from 75 to 300 μM, have been obtained using the currents of the anodic peak measured on the CVs recorded, at 10 V s^?1, at a carbon fiber microelectrode, in a stationary solution of methylmercury chloride. Data have shown that the carbon microelectrode, cycled continuously in the analyte, can replace the dropping mercury electrode (DME), with the advantages that the carbon microelectrode is a promising tool for further studies in high resistive media, such as in natural waters.     

A new method for the determination of loratadine at an Au microelectrode in flowing systems with the use of fast continuous cyclic voltammetry

This research presents a new method for the fast monitoring of loratadine in pharmaceutical formulation. The method employs the fast Fourier transformation continuous cyclic voltammetry (FFTCV) at a gold microelectrode in a flowing-solution system. Three considerable advantages of the technique are demonstrated. First, there is not any requirement for the oxygen removal from the test solution; second, a subnanomolar detection limit is gained; and, finally, the speed of the method for the determination of a compound is in a broad range of chromatographic methods. A special computer-based numerical method is also introduced for the calculation of the analyte signal and noise reduction. The electrode response was calculated in accordance with the partial and total charge exchanges on the electrode surface after the background current subtraction from that of the noise. The integration range of the currents was set for all potential scan ranges, including the oxidation and reduction of the Au surface electrode in order to obtain a sensitive determination. The objective of the performed experiments was to study the effects of different parameters on the method sensitivity. It was concluded that the method had a linear concentration range of 40–765000 pg/mL (r = 0.999) with a limit of detection and quantitation of 12 and 40 pg/mL, respectively. For the achievement of these optimum results, the parameter values were set to 80 V/s for the scan rate, 0.7 s for the accumulation time, 300 mV for the accumulation potential, and 2 for the pH. The text was submitted by the authors in English.     

碳纳米管粉末微电极技术研究超氧自由基的电产生及化学性质

将多壁碳纳米管填充在粉末微电极尖端的小孔里制成碳纳米管粉末微电极,研究氧单电子还原产生超氧自由基的电化学行为.在二甲亚砜(DMSO)介质中,该电极反应是一个近乎可逆的还原/氧化过程,峰电位差(ΔEp)120mV,并显示出良好的稳态伏安曲线.根据极化曲线算得该电极反应的异相电荷传递速率常数ks=9.8×10-3cm/s.此外,还研究了超氧自由基的氧化性和碱性,并对相关反应过程作了讨论.     

The surface catalytic mechanism: a comparative study with square-wave and staircase cyclic voltammetry

A pseudo-first-order catalytic mechanism in which both reactant and product of a redox reaction are strongly immobilized on an electrode surface is theoretically analysed under conditions of square-wave (SWV) and staircase cyclic voltammetry (SCV). A mathematical procedure is developed under diffusionless conditions. The relationships between the properties of the voltammetric response and both the kinetic parameters of the redox reaction and the parameters of the excitation signal are studied. The phenomenon of the quasi-reversible maximum is discussed. A comparative study between SWV and SCV is presented and the limitations and advantages of both techniques, from analytical and kinetic points of view, are discussed. The theoretical predictions are experimentally confirmed by the redox reaction of azobenzene in the presence of hydrogen peroxide as an oxidizing agent. Electronic Publication     

Subsecond FFT‐adsorptive Voltammetric Technique as a Novel Method for Subnano Level Monitoring of Piroxicam in its Tablets and Bulk Form at Au Microelectrode in Flowing Solutions

Abstract

In this work a novel method for the determination of piroxicam in flow‐injection systems has been developed. A system using fast Fourier transform continuous cyclic voltammetry (FFTCV), at a gold microelectrode in flowing solution, was used for determining piroxicam in its pharmaceutical formulations. The developed technique is very simple, precise, accurate, time saving, and economical, compared to all of the previously reported methods. The effects of various parameters on the sensitivity of the method were investigated. The best performance was obtained with a pH value of 2, scan rate value of 40 V/s, accumulation potential of (400) mV, and accumulation time of 0.4 s. The proposed method has some advantages over other reported methods, such as, no need for the removal of oxygen from the test solution, a picomolar detection limit, and finally that the method is fast enough for the determination of any such compound, in a wide variety of chromatographic methods. To obtain a sensitive determination, the integration range of currents was set for all the potential scan ranges, including oxidation and reduction of the Au surface electrode, while performing the measurements. The potential waveform, consisting of the potential steps for cleaning, accumulation, and potential ramp of analyte, was applied on an Au disk microelectrode (with a 12.5 µm in radius) in a continuous way. The method was linear over the concentration range of 1.5–364000 pg/ml (r=0.998) with a limit of detection and quantitation of 0.33 and 1.5 pg/ml, respectively. The method has the requisite accuracy, sensitivity, precision, and selectivity to assay piroxicam in tablets.     

Extraction of electrode kinetic parameters from microdisc voltammetric data measured under transport conditions intermediate between steady-state convergent and transient linear diffusion as typically applies to room temperature ionic liquids

The extraction of electrode kinetic parameters for electrochemical couples in room-temperature ionic liquids (RTILs) is currently an area of considerable interest. Electrochemists typically measure electrode kinetics in the limits of either transient planar or steady-state convergent diffusion for which the voltammetric response is well understood. In this paper we develop a general method allowing the extraction of this kinetic data in the region where the diffusion is intermediate between the planar and convergent limits, such as is often encountered in RTILs using microelectrode voltammetry. A general working surface is derived, allowing the inference of Butler-Volmer standard electrochemical rate constants for the peak-to-peak potential separation in a cyclic voltammogram as a function of voltage scan rate. The method is applied to the case of the ferrocene/ferrocenium couple in [C2mim][N(Tf)2] and [C4mim][N(Tf)2].     

Elimination voltammetry of adenine and cytosine mixtures.

The elimination voltammetry with linear scan (EVLS) was used to study adenine and cytosine reduction signals at the mercury electrode. In comparison with the linear scan voltammetry (which provides only one unresolved peak), two elimination functions provide good resolution of individual peaks and significant increase of sensitivity. The first elimination function eliminates the kinetic current (I(k)) and conserves the diffusion current (I(d)). The second elimination function eliminates kinetic and charging currents (I(k) and I(c)) simultaneously and conserves the diffusion current (I(d)). Both functions give two well-resolved peaks of adenine and cytosine in a wide concentration range, while the linear sweep voltammetry gives badly resolved peaks due to hydrogen evolution. The best resolution of peaks is observed in acetate buffer at pH 3.8 and the detection limit for both substances is 500 nM. The concentration dependence of EVLS peak heights for one substance at the constant concentration of the other substance is linear. The peak potentials differ in these elimination functions. The difference in EVLS peak potentials gives the possibility to evaluate alpha n(a). Elimination voltammetry with linear scan contributes to the resolution of cathodic signals of purine and pyrimidine bases at very negative potentials near supporting electrolyte discharge.     

Advantages of using a mercury coated, micro-wire, electrode in adsorptive cathodic stripping voltammetry

A mercury coated, gold, micro-wire electrode is used here for the determination of iron in seawater by catalytic cathodic stripping voltammetry (CSV) with a limit of detection of 0.1 nM Fe at a 60 s adsorption time. It was found that the electrode surface is stable for extended periods of analyses (at least five days) and that it is reactivated by briefly (2 s) applying a negative potential prior to each scan. Advantages of this electrode over mercury drop electrodes are that metallic mercury use is eliminated and that it can be readily used for flow analysis. This is demonstrated here by the determination of iron in seawater by continuous flow analysis. It is likely that this method can be extended to other elements. Experiments using bismuth coated, carbon fibre, electrodes showed that the bismuth catalyses the oxidation of the important oxidants bromate and hydrogen peroxide, which makes it impossible to use bismuth based electrodes for catalytic CSV involving these oxidants. For this reason mercury coated electrodes retain a major advantage for catalytic voltammetric analyses.     

PVC膜修饰粉末微电极的研制及应用

聚合物具有催化、导电和选择分离等功能,将其与电极合为一体作为新的电极材料,可为改善固体电极的灵敏度、选择性和重现性提供一种新的手段［１,２］．我们用流延法［３］制得ＰＶＣ选择性渗透膜,覆盖于粉末微电极表面,制成了ＰＶＣ膜修饰粉末微电极．该电极性能稳定...