RSD固态脉冲电源中的罗氏线圈电流检测技术

 介绍了基于高速大功率反向开关晶体管(RSD)的磁压缩固态脉冲电源试验平台,就RSD状态电流及磁压缩脉冲电流的波形特征对检测环节高需求的问题,研究了罗氏(Rogowski)线圈传感头的频率特性,在对比已有传感头信号处理方法的基础上,给出了一种新型结构的自积分与外积分复合式罗氏线圈的设计过程和参数选取方法,在保证传感器具有1 mV/A灵敏度的前提下,将传感器的工作频带从低频拓宽到线圈的自然角频率。给出了二级磁压缩网络放电的负载电流实验波形及RSD开关的触发、导通电流波形,验证了该罗氏线圈传感器能够满足本固态脉冲电源中的RSD开关状态电流高精度检测和负载电流的高频检测要求。     

A phase sensitive optical rotation measurement in a scattered chiral medium using a Zeeman laser

A novel circular polarized optical heterodyne interferometer using a Zeeman laser to measure optical rotation both in nonscattered and scattered chiral medium is proposed. A pair of correlated orthogonal circular polarized light waves of different temporal frequency propagating in the chiral medium at different speed is studied. This results in phase retardation between circular polarized light waves of which the phase difference is proportional to the optical rotation angle of a linear polarized light in a chiral medium. In the mean time, two orthogonal circular polarized light waves can be treated as a circular polarized photon pair that is able to reduce the scattering effect in a scattered chiral medium. Then the optical rotation angle can be measured in the scattering medium. In addition, a common-path configuration with respect to circular polarized light waves immune the background noise. This further improves the sensitivity on optical rotation measurement based on phase difference detection.     

光学非均匀复合材料的多元滞后器模型

提出了光学非均匀纤维增强复合材料的复杂双折射现象的多元滞后器模型。给出了多元滞后器矩阵以及由此衍生的一组光强、方位角及滞后量公式，给出了多元与二元等效的证明，并认为二元滞后量应被看作是多元滞后量的一种统计等效值。穿过非均匀介质的偏振光具有复杂的波前，可分解为一组具有不同空间频率的平面波，且每一束平面波都由一对正交偏振光组成。所有这些平面波在试样前方的、垂直于原入射光方向的屏幕上任一点的干涉，在数学上可表示为表征这些平面波的Ｊｏｎｅｓ向量的不同权值的叠加。由于每一对正交偏振光均对应于一个光学均匀微元的Ｊｏｎｅｓ矩阵，因而可用由若干这些Ｊｏｎｅｓ矩阵的叠加所得的多元滞后量矩阵来表征光学非均匀纤维增强复合材料的双折射行为。 关键词：     

2019年中国声学学会青年人才托举工程项目交流会在南昌召开

为改善电磁超声换能器(electromagnetic acoustic transducer,EMAT)激发横波的特性,提出一种基于正交试验的优化方法,并利用有限元仿真软件COMSOL Multiphysics建立了横波EMAT的有限元模型,应用正交试验和极差分析法,分析了线圈各参数对电磁超声横波的近场长度和半扩散角的影响,比较了线圈各参数影响程度的大小。结果表明,激励电流的频率和线圈的尺寸对横波的传播特性有着明显影响,提高频率会使得横波的近场长度增大及半扩散角减小;其次,减小导线的宽度及间距,以缩小线圈尺寸能有效改善横波的传播特性。     

Finite size disc gradient coil set for open vertical field magnets

A new analytical approach is used in the design of disc-like gradient coils suitable for magnet geometries with main field direction perpendicular to the surface of the disc. An inverse procedure is used to optimize the coil's characteristics, subject to the restrictions imposed by the desired field behavior over a certain set of constraint points inside a predetermined imaging volume. Excellent agreement between the expected values of the gradient magnetic field and the numerical values generated by applying the Biot-Savart law to a discrete current pattern of the perspective disc coil was found. A Finite Element Analysis package was used to predict the fringe gradient field levels for a non-shielded axial disc coil and for a self-shielded transverse disc coil in the vicinity of the magnet poles. The numerical results indicate that for the self-shielded design the gradient fringe field is 1000 times smaller than the corresponding fringe field for the non-shielded disc case. Also no significant spatial dependence was noticed for the shielded coil's fringe field.     

A novel orthogonal polarized dual-frequency laser using a Y-shaped cavity

In this paper, we propose and demonstrate a novel dual-frequency He-Ne laser based on a Y-shaped cavity. The laser uses a polarization beam splitter to produce two orthogonal polarized beams that oscillate simultaneously in different sub-cavities. The different optical lengths of the cavities produce two longitudinal mode series with different mode spacing. In our experiments, a frequency difference between two orthogonal polarized lights ranging from 26 to 665 MHz was observed by changing the voltage applied to the piezoelectric transducer attached to the mirror of P polarized sub-cavity. The lock-in frequency difference is about 26 MHz. The competing processes were also investigated.     

Strain field manipulation in ultrafast laser inscribed BiB3O6 optical waveguides for nonlinear applications

A novel technique was used to control the spatial overlap of the orthogonal linearly polarized waveguide modes in ultrafast laser inscribed BiB(3)O(6) waveguides. We report that the strain fields induced by the expansion of material in the laser focus can be considered independently in the design of "type II" waveguides guiding orthogonal linearly polarized light. The waveguide with the optimal mode overlap was used for type I birefringently phase-matched second-harmonic generation of a continuous wave laser source at 1047 nm.     

New multiplexed system for synchronous measurement of out-of-plane deformation and two orthogonal slopes

We propose a novel system for synchronous measurement of out-of-plane deformation and two orthogonal slopes using a single camera. The linearly polarized reference beam introduced by an optical fiber interferes with the unpolarized object beam to measure the out-of-plane deformation. A modified Mach—Zehnder interferometer is used to measure the two orthogonal slopes of the out-of-plane deformation. One of the object beams of the Mach—Zehnder interferometer is an unpolarized beam, and the other object beam is split into two orthogonal linearly polarized object beams by a polarizing prism. The two beams are orthogonally polarized. Hence, they will not interfere with each other. The two polarized beams respectively interfere with the unpolarized beam to simultaneously measure the two orthogonal slopes of the out-of-plane deformation. In addition, the imaging lens and apertures are respectively placed in three optical paths to independently control the carrier frequencies and shearing amounts. The effectiveness of this method can be proved by measuring two pressure-loaded circular plates.     

A practical multinuclear transceiver volume coil for in vivo MRI/MRS at 7 T

A practical multinuclear transceiver RF volume coil with improved efficiency for in vivo small animal ¹H/¹³C/²³Na MR applications at the ultrahigh magnetic field of 7 T is reported. In the proposed design, the coil's resonance frequencies for ¹H and ¹³C are realized by using a traditional double-tuned approach, while the resonant frequency for ²³Na, which is only some 4 MHz away from the ¹³C frequency, is tuned based upon ¹³C channel by easy-operating capacitive “frequency switches”. In contrast to the traditional triple-tuned volume coil, the volume coil with the proposed design possesses less number of resonances, which helps improve the coil efficiency and alleviate the design and operation difficulties. This coil design strategy is advantageous and well suitable for multinuclear MR imaging and spectroscopy studies, particularly in the case where Larmor frequencies of nuclei in question are not separate enough. The prototype multinuclear coil was demonstrated in the desired unshielded design for easy construction and experiment implementation at 7 T. The design method may provide a practical and robust solution to designing multinuclear RF volume coils for in vivo MR imaging and spectroscopy at ultrahigh fields. Finite difference time domain method simulations for evaluating the design and 7-T MR experiment results acquired using the prototype coil are presented.     

Orthogonal contributor number for the measurement of sound power

Orthogonal contributors to a global error represent a very efficient design method in terms of both sensing and control of noise radiation. In practice the price of a sensing system will be determined by the number of errors it must resolve. Therefore predicting the most efficient way of measuring radiation power is an important problem. Recently work has compared sensing the number of vibration modes to the number of orthogonal contributors to radiated power. The required number of vibration modes was based on the proximity of the structural mode resonance frequency and the excitation frequency. While ultimately this technique will result in a valid estimate of radiated power, it is shown here that the number of structural modes can be minimized by first considering orthogonal radiators based on structural mode amplitudes. Two disturbance cases are considered: a point force and an even disturbance coupling to each structural mode. Also, under these conditions the practicality of estimating the number of orthogonal radiators when it is assumed that each contributor is equal in amplitude is examined. Finally in an attempt to optimism the number of signals to be sensed, a variable error margin for the estimate of power, based on the ratio of the sound power at each frequency to the maximum peak in the considered frequency range is proposed and analyzed.     

Surface coil imaging of rat spine at 7.0 T

An inductively coupled surface coil for imaging the rat spine at 7 T is described. This planar circular probe was made from microwave substrate to limit the size of the coil and to minimize the magnetic susceptibility. The surface coil was used as a single transmit/receive coil and as a receive-only coil with a birdcage body coil for excitation. The signal-to-noise ratio (SNR) of the probe was compared to a 5-cm birdcage coil and exceeded the birdcage coil's SNR by three to six times at superficial structures. The main advantages of the probe are an improved SNR for superficial structures and a simple design and use. Images with 50 × 50 × 500 μm voxels were obtained of the rat spine with excellent anatomical detail.     

Lamb wave signal selective enhancement by an improved design of meander-coil electromagnetic acoustic transducer

In this paper, we investigate a method of selectively enhancing the single mode signal of a Lamb wave by using a meander-coil electromagnetic acoustic transducer(EMAT) with a new magnetic configuration. We use the Lamb antisymmetric(A0) mode and symmetric(S0) mode as an example for analysis. The analytical expression of the magnitude of the spatial Fourier transform of the Lorentz force generated by different meander coils is used to determine the optimal driving frequency for single mode generation. The numerical calculation is used to characterize the new magnetic configuration and the conventional EMAT magnet. Experimental examinations of each meander coil in combination with the conventional and new magnetic configuration show that the Lamb wave signal can be selectively enhanced by choosing the appropriate driving frequency and coil parameters through using the improved meander-coil EMAT.     

Diode-pumped cw tunable two-frequency YAG:Nd<Superscript>3+</Superscript> laser with coupled resonators

Using the mode splitting that can be achieved by exploiting the effect of photoelasticity and the mode selection properties of coupled resonators, single- and two-frequency operation of a diode pumped cw YAG:Nd³⁺ laser was observed. In the two-frequency case, a regime with two orthogonal linearly polarized modes was realized. The frequency difference between the adjacent modes could be varied from 50 MHz to 8.4 GHz. A maximum laser output power of 12 mW was achieved at a pump level of 240 mW . Received: 1 November 2002 / Revised version: 14 January 2003 / Published online: 19 March 2003 RID="*" ID="*"Corresponding author. Fax: +375-17/2840-879, E-mail: ryabtsev@dragon.bas-net.by     

Numerical analysis of a photonic crystal fiber based on two polarized modes for biosensing applications

This paper presents a theoretical study on a photonic crystal fiber plasmonic refractive index biosensor. The proposed photonic crystal fiber sensor introduces the concept of simultaneous detection with the linearly polarized and radially polarized modes because the sensing performance of the sensor based on both modes is relatively high, which will be useful for selecting the modes to make the detection accurately. The sharp single resonant peaks of the linearly polarized mode and radially polarized mode, are stronger and more sensitive to the variation of analyte refractive index than that of any other polarized mode in this kind of photonic crystal fiber. For linearly polarized mode and radially polarized mode, the maximum sensitivities of 10448.5nm per refractive index unit and 8230.7nm per refractive index unit can be obtained, as well as 949.8 and 791.4 for figure of merits in the sensing range of 1.33-1.45, respectively. Compared with the conventional Au-metalized surface plasmon resonance sensors, our device is better and can be applied as a biosensor.     

Measurement of electron spin lifetime and optical orientation efficiency in germanium using electrical detection of radio frequency modulated spin polarization

We propose and demonstrate a technique for electrical detection of polarized spins in semiconductors in zero applied magnetic fields. Spin polarization is generated by optical injection using circularly polarized light which is modulated rapidly using an electro-optic cell. The modulated spin polarization generates a weak time-varying magnetic field which is detected by a sensitive radio-frequency coil. Using a calibrated pickup coil and amplification electronics, clear signals were obtained for bulk GaAs and Ge samples from which an optical spin orientation efficiency of 4.8% could be determined for Ge at 1342 nm excitation wavelength. In the presence of a small external magnetic field, the signal decayed according to the Hanle effect, from which a spin lifetime of 4.6±1.0 ns for electrons in bulk Ge at 127 K was extracted.     

Single high-order round-trip feedback effects in orthogonally polarized dual frequency laser

We present the effects of single high-order round-trip feedback in orthogonally polarized dual frequency laser. The high quality intensity fringes of two orthogonally polarized lights are obtained, which are cosine-like. The fringe frequency of a single high-order round-trip feedback is five times that of the conventional optical feedback. Even higher frequencies are possible with this setup. Particularly, there is a phase difference between two orthogonal polarized lights in single high-order round-trip feedback and the phase difference is determined by the feedback order, the length of the external cavity, and the frequency difference of the two orthogonal polarized lights. A theoretical analysis based on a compound cavity model of a dual frequency laser agrees well with the experimental results. These results provide a potential application in precision measurement with both directional discrimination and high optical resolution.     

Design and construction of a versatile dual volume heteronuclear double resonance microcoil NMR probe

Improved NMR detection of mass limited samples can be obtained by taking advantage of the mass sensitivity of microcoil NMR, while throughput issues can be addressed using multiple, parallel sample detection coils. We present the design and construction of a double resonance 300-MHz dual volume microcoil NMR probe with thermally etched 440-nL detection volumes and fused silica transfer lines for high-throughput stopped-flow or flow-through sample analysis. Two orthogonal solenoidal detection coils and the novel use of shielded inductors allowed the construction of a probe with negligible radio-frequency cross talk. The probe was resonated at ¹H–²D (upper coil) and ¹H–¹³C (lower coil) frequencies such that it could perform 1D and 2D experiments with active locking frequency. The coils exhibited line widths of 0.8–1.1 Hz with good mass sensitivity for both ¹H and ¹³C NMR detection. ¹³C-directly detected ²D HETCOR spectra of 5% v/v ¹³C labeled acetic acid were obtained in less than 5 min. Demonstration of the probe characteristics as well as applications of the versatile two-coil double resonance probe are discussed.     

耦合腔结构可调谐双频固体激光器的研究

研究了一种激光二极管(LD)抽运的频差可调谐双频固体激光器,对耦合腔实现双频的方法进行了分析。实验中使用输入镜与腔内插入标准具形成耦合腔实现单频运转,双λ/4波片使单纵模激光频率分裂,通过改变两个λ/4波片快轴之间的夹角来实现频差调谐。在LD抽运光功率为290mW的条件下,获得了频差在0～1.1GHz范围内可调、功率为34mW的双频激光输出。     

A distributed equivalent magnetic current based FDTD method for the calculation of E-fields induced by gradient coils

This paper evaluates a new, low-frequency finite-difference time-domain method applied to the problem of induced E-fields/eddy currents in the human body resulting from the pulsed magnetic field gradients in MRI. In this algorithm, a distributed equivalent magnetic current is proposed as the electromagnetic source and is obtained by quasistatic calculation of the empty coil's vector potential or measurements therein. This technique circumvents the discretization of complicated gradient coil geometries into a mesh of Yee cells, and thereby enables any type of gradient coil modelling or other complex low frequency sources. The proposed method has been verified against an example with an analytical solution. Results are presented showing the spatial distribution of gradient-induced electric fields in a multi-layered spherical phantom model and a complete body model.     

基于飞秒光频梳的双频He-Ne激光器频率测量

利用光纤飞秒光频梳和外腔可调谐半导体激光器, 建立了一套双频He-Ne激光器频率测量系统. 选用铷钟作为系统的频率基准, 通过将外腔半导体激光锁定至光频梳使得其频率溯源至铷钟, 再利用外腔可调谐半导体激光与双频He-Ne激光器输出的正交偏振激光拍频, 同时测量两路正交偏振激光频率. 将可调谐半导体激光器锁定至光频梳第1894449个梳齿, 其绝对频率为473612190000.0±2.7 kHz, 相对不确定度为5.7×10^-12. 对商品双频He-Ne激光器进行频率测量实验, 双频He-Ne激光器水平方向偏振激光频率均值为473612229934 kHz, 竖直方向偏振激光频率均值为473612232111 kHz, 平均时间为1024 s的相对Allan标准差为5.2×10^-11, 频差均值为2.177 MHz, 标准偏差为2 kHz.