An internal surface reversed phase column for the effective removal of humic acid interferences in the trace analysis of mecoprop in soils with coupled-column RPLC-UV

In the development of a screening method for the determination of residues of mecoprop in soils involving coupled-column RPLC-UV (228 nm) the cleanup performance of a 5 μm GFF-II internal surface reversed phase (ISRP, Pinkerton) analytical column (50 × 4.6 mm I.D.) as a first column was investigated. In comparison to an analytical C18 column the ISRP column substantially improved the separation between acidic analyte and co-extracted humic substances. Under the selected coupled-column conditions soil extracts obtained after hydrolysis with an aqueous alkaline solution, acidifying and centrifugation could be analyzed directly allowing the determination of mecoprop in soils to a level of about 0.02 mg/kg. A rapid concentration step on a 100 mg C18 solid phase extraction (SPE) cartridge was adopted into the procedure providing a limit of detection (S/N = 3) of 0.01 mg/kg of mecoprop in soil. The method was validated by analyzing freshly spiked soil samples and samples with aged residues. In case of freshly spiked samples the overall recovery was 87% (n = 18, spiked level 0.02–8.0 mg/kg) with a repeatability of 6.8% and a reproducibility of 8.3%. No significant decrease of the recovery was observed for samples with aged residues (n = 15, spiked level 0.1 and 8.0 mg/kg) during a storage of 29 days in the refrigerator at about 4?°C; a storage of 67 days provided a mean recovery of 76% (n = 14, spiked level 8.0 mg/kg).     

Semi-permeable surface analytical reversed-phase column for the improved trace analysis of acidic pesticides in water with coupled-column reversed-phase liquid chromatography with UV detection. Determination of bromoxynil and bentazone in surface water.

The coupled-column (LC-LC) configuration consisting of a 3 microm C18 column (50 x 4.6 mm I.D.) as the first column and a 5 microm C18 semi-permeable-surface (SPS) column (150 x 4.6 mm I.D.) as the second column appeared to be successful for the screening of acidic pesticides in surface water samples. In comparison to LC-LC employing two C18 columns, the combination of C18/SPS-C18 significantly decreased the baseline deviation caused by the hump of the co-extracted humic substances when using UV detection (217 nm). The developed LC-LC procedure allowed the simultaneous determination of the target analytes bentazone and bromoxynil in uncleaned extracts of surface water samples to a level of 0.05 microg/l in less than 15 min. In combination with a simple solid-phase extraction step (200 ml of water on a 500 mg C18-bonded silica) the analytical procedure provides a high sample throughput. During a period of about five months more than 200 ditch-water samples originating from agricultural locations were analyzed with the developed procedure. Validation of the method was performed by randomly analyzing recoveries of water samples spiked at levels of 0.1 microg/l (n=10), 0.5 microg/l (n=7) and 2.5 microg/l (n=4). Weighted regression of the recovery data showed that the method provides overall recoveries of 95 and 100% for bentazone and bromoxynil, respectively, with corresponding intra-laboratory reproducibilities of 10 and 11%, respectively. Confirmation of the analytes in part of the samples extracts was carried out with GC-negative ion chemical ionization MS involving a derivatization step with bis(trifluoromethyl)benzyl bromide. No false negatives or positives were observed.     

Microwave assisted solvent extraction and coupled-column reversed-phase liquid chromatography with UV detection use of an analytical restricted-access-medium column for the efficient multi-residue analysis of acidic pesticides in soils.

A screening method has been developed for the determination of acidic pesticides in various types of soils. Methodology is based on the use of microwave assisted solvent extraction (MASE) for fast and efficient extraction of the analytes from the soils and coupled-column reversed-phase liquid chromatography (LC-LC) with UV detection at 228 nm for the instrumental analysis of uncleaned extracts. Four types of soils, including sand, clay and peat, with a range in organic matter content of 0.3-13% and ten acidic pesticides of different chemical families (bentazone, bromoxynil, metsulfuron-methyl, 2,4-D, MCPA, MCPP, 2,4-DP, 2,4,5-T, 2,4-DB and MCPB) were selected as matrices and analytes, respectively. The method developed included the selection of suitable MASE and LC-LC conditions. The latter consisted of the selection of a 5-microm GFF-II internal surface reversed-phase (ISRP, Pinkerton) analytical column (50 x 4.6 mm, I.D.) as the first column in the RAM-C18 configuration in combination with an optimised linear gradient elution including on-line cleanup of sample extracts and reconditioning of the columns. The method was validated with the analysis of freshly spiked samples and samples with aged residues (120 days). The four types of soils were spiked with the ten acidic pesticides at levels between 20 and 200 microg/kg. Weighted regression of the recovery data showed for most analyte-matrix combinations, including freshly spiked samples and aged residues, that the method provides overall recoveries between 60 and 90% with relative standard deviations of the intra-laboratory reproducibility's between 5 and 25%; LODs were obtained between 5 and 50 microg/kg. Evaluation of the data set with principal component analysis revealed that the parameters (i) increase of organic matter content of the soil samples and (ii) aged residues negatively effect the recovery of the analytes.     

Fractionation analysis of trace metals in humic substances of soils irrigated with wastewater in Central Mexico by particle induced X-ray emission

The Mezquital Valley in Central Mexico has received wastewater from Mexico City for nearly 100 years. Wastewater brings in organic matter and nutrients but also trace metals. Humic substances, the main components of organic soil matter, are responsible for retaining and regulating the mobility of trace metals in soils. In this study, humic substances were extracted from the soil and separated into distinct fractions (humic acids, fulvic acids and humins). The particle induced X-ray emission (PIXE) technique was applied to determine the metal content in bulk soil as well as in humic acids and fulvic acids not soluble in H₃PO₄. In order to assess whether the long-term input of organic matter and metals modifies the metal association with these humic substances, parcels irrigated for three time periods (5, 47 and 89 years) were selected for this study. It was observed that metals such as Zn and Cu are mainly associated with the humic acids. Fulvic acids retain mainly Cr while Pb is distributed among humic and fulvic acids. It was also observed that in general, metal retention by humic substances increases with irrigation time. Depth also affects metal association with the humic substances.     

Use of aminoprophyl silica-immobilized humic acid for Cu(II) ions removal from aqueous solution by using a continuously monitored solid phase extraction technique in a column arrangement

Humic acid (HA) which originated from Leonardite was purified and immobilized onto aminoprophyl silica (APS). Afterwards, the remaining amino groups on the silica are successfully end-capped using acetic anhydride in DMF media and this material was used for Cu(II) ions removal from aqueous solution by using continuously solid phase extraction (SPE) technique in a column arrangement. The sorption characteristics of Cu(II)-immobilized humic acid (ImHA) system were investigated at various experimental conditions, and output was observed by a UV detector. All solid phase extraction (SPE) steps were monitored through breakthrough curves used to visualize distribution of Cu(II) concentration between mobile phase and solid phase. In addition to this, the solutions collected from stripping steps were analyzed in atomic absorption spectrophotometry (AAS) and the amount of adsorbed Cu(II) ions was calculated. It was found that there was a high correlation (R² = 1) between the peak area and AAS data of stripping steps. Sorption characteristics were evaluated by using Freundlich, Langmuir, and Dubinin–Radushkevich (D-R) adsorption isotherms, as well as by Scatchard plot analysis. Thus, the sorption characteristics and usability of ImHA as a solid phase for SPE of Cu(II) ions was evaluated in detail. From the obtained results, it was seen that sorption mechanism of Cu(II) fits to Langmuir model on a large scale, sorption was thought to be localized. From D-R isotherm mean free energy of sorption (E) was calculated (17.68 kJ mol⁻¹), and it was deduced that chemical interactions were more effective than physical interactions for Cu(II). This investigation provides a new, environmentally friendly and cost-effective possibility to remove Cu(II) ions from aqueous solution by using the new APS-ImHA material.     

Removal of humic acid and surfactant interferences in trace metal determinations by differential-pulse anodic stripping voltammetry with use of adsorption and chelate ion-exchanger columns in a flow-injection system

A flow-injection differential-pulse anodic stripping voltammetry (d.p.a.s.v.) method is modified so that interferences from humic acids or surfactants are eliminated. The injected, slightly acidic sample is passed through a silica anion-exchanger column to remove compoundswith a strong tendency to adsorb to the electrode. The sample then passes to a chelate ion-exchange column containing immobilized 8-quinolinol. The metal ions are retained and later eluted with acid into the voltammetric cell. The results show that the interferences from up to 500 mg 1^–1 humic acid or at least 50 mg 1^-1 Triton X-100 can be removed and that the metal ion can be determined in a range similar to that for normal d.p.a.s.v. methods. The complete cycle time for a determination was 12 min.     

Retention prediction of polycyclic aromatic hydrocarbons in reversed phase liquid chromatography with various mobile phase compositions and column temperatures

Summary The relationship between the logarithmic capacity factor measured in reversed-phase liquid chromatography and the operating conditions including the mobile phase composition and the column temperature is investigated. The strategy described herein can offer the possibility to predict the retention of polycyclic aromatic hydrocarbons without any experiments and standard materials, by utilizing equations describing the relationships between retention, temperature, mobile phase composition and physicochemical properties of the solutes previously stored in the program of the microcomputer-assisted retention prediction system.This concept is one of the most promising techniques for the optimization of the separation conditions in reversed-phase liquid chromatography.     

An internal standard method for the determination of trace elements in cigarette tobacco by neutron activation analysis

An internal standard method has been applied for the determination of lanthanum, antimony, scandium, chromium, iron and cobalt in commercial cigarettes by neutron activation analysis using gold as an internal standard element. These trace elements were separated from irradiated samples by APDC (ammonium pyrrolidine dithiocarbamate)/Zeph (tetradecyl dimethyl benzyl ammonium chloride) coprecipitation, followed by direct gamma-counting of the separated precipitate using a Ge(Li) detector. Standard reference tobacco 1R1 prepared by the University of Kentucky was also analyzed by this procedure for the above 6 elements, the results of which were compared with literature values. Good results were obtained by the present method.     

Effect of high pH column regeneration on the separation performances in reversed phase chromatography of peptides

Caustic regeneration procedures are often used in chromatographic purification processes of peptides and proteins to remove irreversibly bound impurities from the stationary phase. Silica-based materials are the most commonly used materials in reversed phase chromatography of peptides. Their limited chemical stability at high pH can be, however, problematic when high pH column regeneration (i.e. cleaning in place) is required. The effect of cleaning in place on the surface chemistry of the stationary phase has been investigated using the Tanaka test. It has been shown that the high pH treatment does not significantly affect the hydrophobicity of the material, but it strongly increases its silanol activity. A representative peptide purification process has been used to investigate the impact of cleaning in place on the separation performance. It has been shown that the caustic regeneration increases the peptide retention at high pH (pH 6.5), due to the interactions between the peptide and the negatively charged silanol groups. These unwanted interactions reduce the separation performances by decreasing the selectivity between the late eluting impurities and the main peptide. However, it has been shown that the effect of the silanol groups on the peptide adsorption and on the separation performance can be minimized by carrying out the purification process at low pH (pH ∼ 2). In this case, the silanol groups are protonated and their electrostatic interactions with the positively charged analyte (i.e. peptides) are suppressed. In these conditions, the peptide adsorption and the impurity selectivity is not changing upon high pH column regeneration and the separation performance is not affected.     

A selective GC column for trace analysis of vinyl chloride in air

Summary A selective GC column for the determination of vinyl chloride monomer in air has been developed. The 1.5m×1/8 column is filled with a mixture of Porapack S and T (8020). The selectivity was tested with 21 possible pollutants. All of the tested compounds were separated from vinyl chloride.     

Retention and column efficiency in reversed phase liquid chromatography as a function of pH for optimization purposes

Summary The effects of pH on both the solute retention and the peak shape of ionogenic compounds are studied in order to propose accurate models for pH optimization purposes. Several mathematical models (theoretical and empirical) for describing the variation of the retention factor versus pH are compared within different pH ranges. Limits of such models used for optimizing the pH by requiring only 3 preliminary experimental runs, are discussed in terms of deviations (≤±5%) of predicted retention times from experimental retention times. An original procedure is developed for selecting the most convenient retention model, from a given set of three retention data. This set is also applied to modeling the variation of both peak width and peak asymmetry with mobile phase pH conditions. Such a procedure is demonstrated as helpful for the separation of ionogenic solutes by considering mobile phase pH as an additional variable that can be useful during optimization procedures.     

Comparison of procedures for correction of matrix interferences in the multi-element analysis of soils by ICP-AES with a CCD detection system

Three procedures, matrix matching, plasma optimisation and single-point standard-addition, have been evaluated to ascertain the best procedure for simultaneous multi-element analysis of industrial soils by ICP-AES with CCD detection. A standard reference material, CRM143 from the Bureau Communautaire de Réference (BCR), has been analysed for Cd, Cr, Cu, Mn, Ni and Pb using the three different matrix interference correction procedures. All three procedures give comparable results which are in good agreement with the BCR values, except for Cr. The single-point standard addition procedure was chosen, on the basis of economy and ease of implementation, to correct for matrix interferences in the determination of Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, Sn and V in soil samples collected from an industrial site in England. Concentrations of some of the elements were found to vary greatly with sampling depth. For example, the concentration of Mn, determined using the atomic line at 279.920 nm, increased from 426 ± 3 g/g at a depth of 18–28 cm to 5996 ± 144 g/g at 60–85 cm.     

Application of an internal surface reversed-phase column for the automated determination of flucycloxuron residues

A liquid chromatographic column-switching system for the automated determination of flucycloxuron, a benzoylphenylurea pesticide, in crop and environmental matrices is described. The system consists of an internal surface reversed-phase (ISRP) column, a phenyl-bonded precolumn and an analytical reversed-phase (RP) C₁₈ column. Sample extracts are evaporated to dryness and dissolved in the mobile phase of the ISRP column. An aliquot of this solution is injected into the column-switching system. Clean-up, with regard to removal of large molecules, is performed on the ISRP column. The flucycloxuron fraction from the ISRP column is concentrated on the phenyl-bonded precolumn. Additional clean-up can be performed by washing the precolumn. Finally, the compound is desorbed from the precolumn and separation and determination of the Z- and E-isomers of flucycloxuron are performed with the analytical RP-C₁₈ column using UV detection at 254 nm. The total analysis time required is 40 min. The reproducibility of the method obtained with the column-switching system, expressed as relative standard deviation, varies between 3.7 and 10% for apple, strawberry, citrus and soil samples for flucycloxuron levels between 0.04 and 0.33 mg/kg. The system showed no loss of analytical performance after more than 300 analyses.     

Advanced mesoporous organosilica material containing microporous beta-cyclodextrins for the removal of humic acid from water

A new mesoporous organosilica material (beta-CD-Silica-4%) containing microporous beta-cyclodextrins (beta-CDs) has been prepared by the co-polymerization of a silylated beta-CD monomer with tetraethoxysilane in the presence of a structure-directing template, cetyltrimethylammonium bromide. Solid-state 13C and 29Si NMR studies provided evidence for the presence of covalently attached beta-CDs in the mesoporous material. Nitrogen adsorption experiments showed that beta-CD-Silica-4% material had a BET surface area of 460 m2/g and an average mesopore diameter of 2.52 nm. Small-angle powder X-ray diffraction pattern of beta-CD-Silica-4% material revealed the lack of highly ordered mesoporous structure. Adsorption experiments showed that beta-CD-Silica-4% material removed up to 99% of humic acid from an aqueous solution containing 50 ppm of humic acid at a solution-to-solid ratio of 100 ml/g.     

Performance of a photocatalytic hybrid system coupled with a stainless steel membrane for removal of humic acid

The objective of this study was to evaluate the performance of a photocatalysis/H₂O₂/metal membrane hybrid system in the degradation of humic acid. A metal membrane of nominal pore size 0.5 μm was used in the experiment for separation of TiO₂ particles. Hydrogen peroxide was tested as an oxidant. The efficiency of removal of COD_Cr and color increased rapidly for initial hydrogen peroxide concentrations up to 50 mg L⁻¹. The efficiency of removal of COD_Cr and color by 50 mg L⁻¹ initial hydrogen peroxide concentration was approximately 95 and 98%, respectively. However, addition of hydrogen peroxide over 50 mg L⁻¹ inhibited the efficiency of the system. Addition of hydrogen peroxide to a UV/TiO₂ system enhanced efficiency of removal of COD_Cr and color compared with no addition of hydrogen peroxide. This may be ascribed to capture electrons ejected from TiO₂ and to the production of OH radicals. Application of the metal membrane in the UV/TiO₂/H₂O₂ system enhanced the efficiency of removal of COD_Cr and color because of adsorption by the metal membrane surface and the production of OH radicals. By application of a metal membrane with a nominal pore size of 0.5 μm, TiO₂ particles were effectively separated from the treated water by metal membrane rejection. The photocatalytic metal membrane had much less resistance than the humic acid, TiO₂, and humic acid/TiO₂ because of the degradation of humic acid by the photocatalytic reaction.     

Practical,stable standards for the reversed phase HPLC analysis of peptidic leukotrienes

The stable glutathione derivatives 1, R = n-C₆H₁₃ and R = n-C₈H₁₇, are useful as reference compounds for the identification and quantitation of leukotrienes C₄, D₄ and E₄ by reversed phase HPLC analysis.     

Dependence of the specific surface area of a stationary phase on the phase amount in the column packings for GLC

Summary The dependence of the specific surface area of a stationary phase on the phase amount in the packings is of great importance for the detailed study of the solute retention in GLC. Two equations describing this dependence, are derived on the basis of a thermodynamical consideration. The first equation is valid up to the formation of a stationary phase monolayer on the solid surface, while the second after the monolayer formation. The validity of the latter equation has been tested experimentally. A good agreement has been achieved.     

Dual gradient LC method for the determination of pharmaceutical residues in environmental samples using a monolithic silica reversed phase column

Detailed below is a simple reversed-phase liquid chromatography (RP-LC) method for the simultaneous separation of up to 21 acidic, basic, and neutral pharmaceuticals using Merck Chromolith Performance RP-C18e monolithic columns with direct ultraviolet (UV) absorption detection. By simultaneously applying a solvent elution gradient program with a mobile phase flow gradient, both a decrease in the overall analysis time and a general increase in peak efficiencies were observed. Mobile phase pH and buffer concentration were optimised using the overall resolution product under applied gradient conditions. Under optimised conditions peak area reproducibility (n?=?6) ranged between 0.4 and 9.3%, determined at the method LOQ level. For real sample analysis pharmaceutical residues were extracted using an optimised solid phase extraction (SPE) procedure, utilising Strata-X extraction cartridges, which overall provided the highest relative recovery data in comparison with four other commercially available SPE sorbents (17 out of 20 residues investigated had recoveries over 70%). Complete method precision, including all sample pre-treatment and LC analysis for six spiked river water samples at the 1 and 2?µg?L^?1 level was between 10 and 29%. Using 1?L volumes of 1?µg?L^?1 spiked estuarine water samples, the majority of detection limits were found to be in the 10–50?ng?L^?1 range.     

Problems associated with interferences in the analysis of serum for polychlorinated biphenyls

During a recent survey to determine serum concentrations of polychlorinated biphenyls (PCBs) among people living around New Bedford, MA, U.S.A., an unidentified contaminant precluded the quantification of some early eluting Webb and McCall peaks. Loss of data is estimated to have reduced reported serum levels by 12%. Efforts to identify the contaminant by gas chromatography with an electron-capture detector, a Hall electrolytic condutivity detector, and mass spectrometer were not successful. Researchers ascertained, however, that the contaminant is not a PCB, it does not contain halogens, but it may contain phthalates. Vacutainer tubes and closures for serum storage bottles are suspected sources of contamination.