Interface hydrogen-bonded core-shell nanofibers by coaxial electrospinning

Core-shell nanofibers were prepared by coaxial electrospinning technology,with poly(ethylene oxide) (PEO) as the core while poly(acrylic acid) (PAA) as the shell.PEO and PAA can form polymer complexes based on hydrogen bonding.In order to avoid forming strong hydrogen bonding complexes at nozzle and blocking spinning process,a polar aprotic solvent,N,N-dimethylformamide (DMF),was selected to dissolve PEO and PAA respectively.SEM,TEM and DSC were utilized to characterize the morphology and structure of PEO-PAA core-shell nanofibers.FTIR spectra demonstrated that hydrogen bonding was formed at the core-shell interface.In addition,the PAA shell of the nanofibers can be cross-linked by ethylene glycol (EG) under heat treatment,which increases the stability and extends the potential applications in aqueous environment.     

Single step hybrid coating process to enhance the electrosteric stabilization of inorganic particles

We report on a single-step coating process and the resulting colloidal stability of silica-coated spindle-type hematite nanoparticles (NPs) decorated with a layer of poly(acrylic acid) (PAA) polyelectrolyte chains that are partially incorporated into the silica shell. The stability of PAA coated NPs as a function of pH and salt concentration in water was compared to bare hematite particles and simple silica-coated hematite NPs, studying their electrophoretic mobility and the hydrodynamic radius by dynamic light scattering. Particles coated with this method were found to be more stable upon the addition of salt at pH 7, and their aggregation at the pH of the isoelectric point is reversible. The hybrid coating appears to increase the colloidal stability in aqueous media due to the combination of the decrease of the isoelectric point and the electrosteric stabilization. This coating method is not limited to hematite particles but can easily be adapted to any silica-coatable particle.     

两亲性杂壳聚合物粒子的高效制备及以其作为模板合成金纳米簇合物

将等质量的嵌段聚合物聚乙烯基萘聚丙烯酸和聚氧化乙烯聚丙烯酸（P2VN-b-PAA和PEO-b-PAA）溶解于N,N′-二甲基甲酰胺(DMF)中,加入小分子二元胺（1,2-丙二胺,PDA）,制备出均匀的两亲性杂壳聚合物纳米粒子(MSNPs)。 该粒子以PEO和P2VN混合嵌段为壳层,非共价键交联的PAA嵌段为核,在水相及有机相中均可稳定分散,具有典型的两亲性特点。 扫描电子显微镜和光散射测试结果表明,该杂壳聚合物粒子(MSNPs)的粒径在300 nm左右,分布较均匀,并显示出壳层可塌缩变形的疏松核（软粒子）特征。 以该聚合物粒子(MSNPs)为模板,可以方便制备出金纳米粒子簇合物。     

Preparation and characterization of poly(acrylic acid)-based nanoparticles

The present investigation describes the synthesis and characterization of nanoparticles based on poly(acrylic acid) (PAA) intramolecularly cross-linked with diamine, 2,2′-(ethylenedioxy)bis(ethylamine), using water-soluble carbodiimide. The aqueous colloid dispersions of nanoparticles were clear or mildly opalescent depending on the ratio of cross-linking, pH of the solution, and the molecular weight of PAA, finding consistent with values of transmittance between 3% and 99%. The structure was determined by nuclear magnetic resonance spectroscopy, and the particle size was identified by dynamic light scattering (DLS) and transmission electron microscopy (TEM) measurements. It was found that particle size depends on the pH, and at a given pH, it was caused by the ratio of cross-linking and the molecular weight of PAA. Particle size measured by TEM varied in the range of 20 and 80 nm. In the swollen state, the average size of the particles measured by DLS was in the range of 35–160 nm.     

Hydrophilic magnetic polymer latexes. 1. Adsorption of magnetic iron oxide nanoparticles onto various cationic latexes

With a view to preparing monosized hydrophilic functional magnetic latex particles based on a two-step strategy using anionic iron oxide and cationic polymer latexes, the adsorption step was systematically investigated for a better control of the subsequent encapsulation step. The iron oxide nanoparticles were first obtained according to the classical precipitation method of ferric and ferrous chloride salt using a concentrated sodium hydroxide solution, whereas the polystyrene (PS), P(S/N-isopropylacrylamide (NIPAM)) core–shell and PNIPAM latexes were produced via emulsion and precipitation polymerizations, respectively. The polymer and inorganic colloids were then characterised. The adsorption of iron oxide nanoparticles onto the three types of polymer latexes via electrostatic interaction was studied as a function of iron oxide particle concentration, charge density and the cross-linking density of the hydrophilic layer. The maximum amounts of magnetic nanoparticles adsorbed onto the various latexes were found to increase in the following order: PS < P(S/NIPAM) < P(NIPAM). This significant difference is discussed by taking into account the charge distribution in the hydrogel layer and diffusion phenomena inside the cross-linked hydrophilic shell. Received: 28 December 1998 Accepted in revised form: 15 April 1999     

CRYSTALLIZATION AND MELTING OF POLY（ETHYLENE OXIDE） CONFINED IN NANOSTRUCTURED PARTICLES WITH CROSS-LINKED SHELLS OF POLYBUTADIENE

Small fixed aggregates of a poly(ethylene oxide)-block-polybutadiene diblock copolymer(PEO-b-PB)in THFsolution were obtained by adding a selective solvent for PB blocks,followed by cross-linking the PB shells.Themorphologies of the nanostructured particles with a cross-linked shell were investigated by atomic force microscopy andtransmission electron microscopy.The average behaviors of the PEO crystallization and melting confined within thenanostructured particles were studied by using differential scanning calorimetry experiments.For the deeply cross-linkedsample(SCL-1),the crystallization of the PEO blocks was fully confined.The individual nanoparticles only crystallized atvery low crystallization temperatures(T_cs),wherein the homogenous primary nucleation determined the overallcrystallization rate.For the lightly cross-linked sample(SCL-2),the confinement effect was T_c dependent.At T_c(?)42℃,thecrystallization and melting behaviors of SCL-2 were similar to those of the pure PEO-b-PB diblock copolymer.At T_c>42℃,SCL-2 could form PEO lamellae thicker than those of the pure PEO-b-PB crystallized at the same T_c.     

Double hydrophilic block copolymer monolayer protected hybrid gold nanoparticles and their shell cross-linking

This paper describes the syntheses of core/shell gold nanoparticles stabilized with a monolayer of double hydrophilic block copolymer and their stimuli responsiveness before and after shell cross-linking. The hybrid nanoparticles consist of gold core, cross-linkable poly(2-(dimethylamino)ethyl methacrylate) (PDMA) inner shell, and poly(ethylene oxide) (PEO) corona. First, diblock copolymer PEO-b-PDMA was prepared via the reversible addition-fragmentation chain transfer (RAFT) technique using a PEO-based macroRAFT agent. The dithioester end group of PEO-b-PDMA diblock copolymer was reduced to a thiol end group. The obtained PEO-b-PDMA-SH was then used to prepare diblock copolymer stabilized gold nanoparticles by the "grafting-to" approach. 1,2-Bis(2-iodoethoxy)ethane (BIEE) was utilized to selectively cross-link the PDMA residues in the inner shell. The stimuli responsiveness and colloidal stability of core/shell gold nanoparticles before and after shell cross-linking were characterized by laser light scattering (LLS), UV-vis transmittance, and transmission electron microscopy (TEM). At pH 9, the average hydrodynamic radius Rh of non-cross-linked hybrid gold nanoparticles starts to increase above 35 degrees C due to the lower critical solution temperature (LCST) phase behavior of the PDMA blocks in the inner shell. In contrast, Rh of the shell cross-linked gold nanoparticles were essentially independent of temperature. Core/shell gold nanoparticles before and after shell cross-linking exhibit reversible swelling on varying the solution pH. Compared to non-cross-linked core/shell gold nanoparticles, shell cross-linking of the hybrid gold nanoparticles leads to permanent core/shell nanostructures with much higher colloidal stability and physically isolates the gold core from the external environment.     

Nanostructured latex films from poly(butyl methacrylate) latex cross-linked with poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide) triblock macro-cross-linker

Biphasic polymer latexes were synthesized by a seeded swelling and polymerization method. The latexes were composed of a poly(butyl methacrylate) core and a poly(ethylene oxide) rich shell cross-linked with poly(ethylene oxide)-poly (propylene oxide)-poly(ethylene oxide) triblock diol diacrylate macro-cross-linker. Nanostructured films were obtained by annealing the biphasic polymer latexes at a temperature between the glass-transition temperatures of the core latex and the cross-linked poly(ethylene oxide) based shell. Atomic force microscope images of the latex film revealed that the poly(butyl methacrylate) core phase is confined in the poly(ethylene oxide)-rich continuous phase with the form of separate nanosized spheres.     

Structural characterisation of poly(amidoamine) networks via high-resolution magic angle spinning NMR

A comprehensive structural characterisation of cross-linked insoluble poly(amidoamine) (PAA) networks was performed by high-resolution magic angle spinning (HRMAS) NMR spectroscopy. Model samples with 20%, 40% and 80% cross-linking degrees were prepared and the best conditions to obtain high-resolution spectra in the gel phase determined. Whereas the samples with 20% and 40% cross-linking degrees could be exhaustively resolved and described, the sample with 80% cross-linking degree could not be characterised by this technique owing to insufficient mobility of the polymer segments. Even with this limitation, the method developed in this study can be reasonably considered as a general one, which enables exhaustive characterisation of cross-linked PAA networks of biomedical interest.     

Preparation of Latexes with Poly(Methyl Methacrylate) Cores and Hydrophilic Polymer Shells Containing Amino Groups

Abstract

Functional latexes with poly(methyl methacrylate) (PMMA) cores and amino‐containing, water‐soluble polymer shells were synthesized via direct graft copolymerization of methyl methacrylate from water‐soluble polymers induced by a small amount of tert‐butyl hydroperoxide (TBHP) at 80°C for 2 h. Amphiphilic graft copolymers and PMMA homopolymers were generated concurrently to form highly monodispersed latexes. The effects of water‐soluble polymer containing different amino group, reaction temperature, TBHP concentration, molecular weight of the polymer and pH of the solution on conversion and grafting efficiency of the monomer and particle size were investigated. Transmission electron microscopic images of the PMMA/poly(ethyleneimine) (PEI) and PMMA/poly(allylamine) (PAA) particles clearly show well‐defined core‐shell morphologies, where PMMA cores are coated with either PEI or PAA shell. The amino‐containing polymer shells were also confirmed with zeta‐potential measurements. Furthermore, the amino‐containing latexes can be produced with a solids content up to 22 wt.%. Thus, this method provides a commercially viable route to functional latexes.     

Hierarchically structured free-standing hydrogels with liquid crystalline domains and magnetic nanoparticles as dual physical cross-linkers

Here we report a modular strategy for preparing physically cross-linked and mechanically robust free-standing hydrogels comprising unique thermotropic liquid crystalline (LC) domains and magnetic nanoparticles both of which serve as the physical cross-linkers resulting in hydrogels that can be used as magnetically responsive soft actuators. A series of amphiphilic LC pentablock copolymers of poly(acrylic acid) (PAA), poly(5-cholesteryloxypentyl methacrylate) (PC5MA), and poly(ethylene oxide) (PEO) blocks in the sequence of PAA-PC5MA-PEO-PC5MA-PAA were prepared using reversible addition-fragmentation chain transfer polymerization. These pentablock copolymers served as macromolecular ligands to template Fe(3)O(4) magnetic nanoparticles (MNPs), which were directly anchored to the polymer chains through the coordination bonds with the carboxyl groups of PAA blocks. The resulting polymer/MNP nanocomposites comprised a complicated hierarchical structure in which polymer-coated MNP clusters were dispersed in a microsegregated pentablock copolymer matrix that further contained LC ordering. Upon swelling, the hierarchical structure was disrupted and converted to a network structure, in which MNP clusters were anchored to the polymer chains and LC domains stayed intact to connect solvated PEO and PAA blocks, leading to a free-standing LC magnetic hydrogel (LC ferrogel). By varying the PAA weight fraction (f(AA)) in the pentablock copolymers, the swelling degrees (Q) of the resulting LC ferrogels were tailored. Rheological experiments showed that these physically cross-linked free-standing LC ferrogels exhibit good mechanical strength with storage moduli G' of around 10(4)-10(5) Pa, similar to that of natural tissues. Furthermore, application of a magnetic field induced bending actuation of the LC ferrogels. Therefore, these physically cross-linked and mechanically robust LC ferrogels can be used as soft actuators and artificial muscles. Moreover, this design strategy is a versatile platform for incorporation of different types of nanoparticles (metallic, inorganic, biological, etc.) into multifunctional amphiphilic block copolymers, resulting in unique free-standing hybrid hydrogels of good mechanical strength and integrity with tailored properties and end applications.     

Polymer-additive extraction via pressurized fluids and organic solvents of variously cross-linked poly(methylmethacrylates)

Variously cross-linked poly(methylmethacrylates) (PMMAs) are synthesized with three additives incorporated at theoretically 1000 microg of the additive per gram of prepared polymer. The additives are Irganox 1010, Irganox 1076, and Irgafos 168. The in-house" synthesized polyacrylates are then subjected to supercritical fluid extraction (SFE) to determine if additive recovery is a function of percent cross-linking. Although considerable work in this regard has been performed with non-cross-linked polyolefins, the literature is lacking regarding polyacrylates. Some additive degradation apparently occurs during the synthesis, as judged by the increased complexity of the extract high-performance liquid chromatographic trace and the low percent recoveries observed especially for the Irganoxes. For low polymer cross-linking (1%), it appears that both PMMA synthetic reproducibility and readily observed polymer swelling during SFE are serious issues that adversely affect additive percent recovery and precision of results. Higher percent cross-linking yields more consistent analytical data than low percent cross-linking, even though the amount of additive extracted in all PMMA samples (regardless of cross-linking percentage) is essentially the same whether the extraction is via SFE or liquid-solid extraction with methylene chloride. Results for comparably cross-linked poly(ethylmethacrylate) and poly(butylmethacrylate) are similar to PMMA.     

Ag Nanocomposite Particles: Preparation,Characterization and Application

Summary Herein, we report that different core-shell particles could be successfully used as the carrier systems for the deposition of silver nanoparticles. Firstly, thermosensitive core-shell microgel particles have been used as the carrier system for the deposition of Ag nanoparticles, in which the core consists of poly (styrene) (PS) whereas the shell consists of poly (N-isopropylacrylamide) (PNIPA) network cross-linked by N, N′-methylenebisacrylamide (BIS). Immersed in water the shell of these particles is swollen. Heating the suspension above 32 °C leads to a volume transition within the shell, which is followed by a marked shrinking of the network of the shell. Secondly, “nano-tree” type polymer brush can be used as “nanoreactor” for the generation of silver nanoparticles also. This kind of carrier particles consists of a solid core of PS onto which bottlebrush chains synthesized by the macromonomer poly (ethylene glycol) methacrylate (PEGMA) are affixed by “grafting from” technique. Thirdly, silver nanoparticles can be in-situ immobilized onto polystyrene (PS) core-polyacrylic acid (PAA) polyelectrolyte brush particles by UV irradiation. Monodisperse Ag nanoparticles with diameter of 8.5 nm, 7.5 nm and 3 nm can be deposited into thermosensitive microgels, “nano-tree” type polymer brushes and polyelectrolyte brush particles, respectively. Moreover, obtained silver nano-composites show different catalytic activity for the catalytic reduction of p-nitrophenol depending on the carrier system used for preparation.     

Stable superhydrophobic organic-inorganic hybrid films by electrostatic self-assembly

Organic-inorganic hybrid films were prepared through layer-by-layer (LBL) deposition of poly(allylamine hydrochloride) (PAH) and ZrO(2) nanoparticles coated with poly(acrylic acid) (PAA), allowing facile control of surface roughness and hydrophobicity. Superhydrophobic behavior was observed after deposition of silica nanoparticles and a simple fluorination of the surface. The structure of films was controlled by the number of deposition cycles using PAA-coated 100 nm ZrO(2) nanoparticles, the particle size, and the prelayer with PAH and PAA. The change in the apparent water contact angle of (PAH/PAA-coated ZrO(2)n surfaces without fluorination of the surface agrees with Cassie and Baxter's model for nonwetted surfaces even though the outermost surface itself is hydrophilic. Superhydrophobic surfaces were then successfully developed by the deposition of hydrophilic silica nanoparticles on a 10 bilayer surface of PAH/PAA-coated ZrO(2), and a simple fluorination. Moreover, the chemical stability of the film was greatly increased by heat-induced cross-linking of the film. The incorporation of ZrO(2) nanoparticles in superhydrophobic films promises better mechanical properties than the organic film.     

Thermally cross-linked superparamagnetic iron oxide nanoparticles: synthesis and application as a dual imaging probe for cancer in vivo

We report the fabrication and characterization of thermally cross-linked superparamagnetic iron oxide nanoparticles (TCL-SPION) and their application to the dual imaging of cancer in vivo. Unlike dextran-coated cross-linked iron oxide nanoparticles, which are prepared by a chemical cross-linking method, TCL-SPION are prepared by a simple, thermal cross-linking method using a Si-OH-containing copolymer. The copolymer, poly(3-(trimethoxysilyl)propyl methacrylate-r-PEG methyl ether methacrylate-r-N-acryloxysuccinimide), was synthesized by radical polymerization and used as a coating material for as-synthesized magnetite (Fe3O4) SPION. The polymer-coated SPION was further heated at 80 degrees C to induce cross-linking between the -Si(OH)3 groups in the polymer chains, which finally generated TCL-SPION bearing a carboxyl group as a surface functional group. The particle size, surface charge, presence of polymer-coating layers, and the extent of thermal cross-linking were characterized and confirmed by various measurements, including dynamic light scattering, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The carboxyl TCL-SPION was converted to amine-modified TCL-SPION and then finally to Cy5.5 dye-conjugated TCL-SPION for use in dual (magnetic resonance/optical) in vivo cancer imaging. When the Cy5.5 TCL-SPION was administered to Lewis lung carcinoma tumor allograft mice by intravenous injection, the tumor was unambiguously detected in T2-weighted magnetic resonance images as a 68% signal drop as well as in optical fluorescence images within 4 h, indicating a high level of accumulation of the nanomagnets within the tumor site. In addition, ex vivo fluorescence images of the harvested tumor and other major organs further confirmed the highest accumulation of the Cy5.5 TCL-SPION within the tumor. It is noteworthy that, despite the fact that TCL-SPION does not bear any targeting ligands on its surface, it was highly effective for tumor detection in vivo by dual imaging.     

Preparation and characterization of low dispersity anionic multiresponsive core-shell polymer nanoparticles

We prepared anionic multistimuli responsive core-shell polymer nanoparticles with very low size dispersity. By using either acrylic acid (AA) or methacrylic acid (MA) as a comonomer in the poly(N-isopropyl acrylamide) (PNIPAM) shell, we are able to change the distribution of negative charges in the nanoparticle shell. The particle size, volume phase transition temperature, and aggregation state can be modulated using temperature, pH, or ionic strength, providing a very versatile platform for applications in sensors, medical diagnostics, environmental remediation, etc. The nanoparticles have a glassy poly(methyl methacrylate) (PMMA) core of ca. 40 nm radius and a cross-linked PNIPAM anionic shell with either AA or MA comonomers. The particles, p(N-AA) and p(MA-N), respectively, have the same total charge but different charge distributions. While the p(MA-N) particles have the negative charges preferentially distributed toward the inner shell, in the case of the p(N-AA) particles the charge extends more to the particle outer shell. The volume phase transition temperature (T(VPT)) of the particles is affected by the charge distribution and can be fine-tuned by controlling the electrostatic repulsion on the particle shell (using pH and ionic strength). By suppressing the particle charge we can also induce temperature-driven particle aggregation.     

An effective polymer cross-linking strategy to obtain stable dispersions of upconverting NaYF4 nanoparticles in buffers and biological growth media for biolabeling applications

Ligands on the nanoparticle surface provide steric stabilization, resulting in good dispersion stability. However, because of their highly dynamic nature, they can be replaced irreversibly in buffers and biological medium, leading to poor colloidal stability. To overcome this, we report a simple and effective cross-linking methodology to transfer oleate-stabilized upconverting NaYF(4) core/shell nanoparticles (UCNPs) from hydrophobic to aqueous phase, with long-term dispersion stability in buffers and biological medium. Amphiphilic poly(maleic anhydride-alt-1-octadecene) (PMAO) modified with and without poly(ethylene glycol) (PEG) was used to intercalate with the surface oleates, enabling the transfer of the UCNPs to water. The PMAO units on the phase transferred UCNPs were then successfully cross-linked using bis(hexamethylene)triamine (BHMT). The primary advantage of cross-linking of PMAO by BHMT is that it improves the stability of the UCNPs in water, physiological saline buffers, and biological growth media and in a wide range of pH values when compared to un-cross-linked PMAO. The cross-linked PMAO-BHMT coated UCNPs were found to be stable in water for more than 2 months and in physiological saline buffers for weeks, substantiating the effectiveness of cross-linking in providing high dispersion stability. The PMAO-BHMT cross-linked UCNPs were extensively characterized using various techniques providing supporting evidence for the cross-linking process. These UCNPs were found to be stable in serum supplemented growth medium (37 °C) for more than 2 days. Utilizing this, we demonstrate the uptake of cross-linked UCNPs by LNCaP cells (human prostate cancer cell line), showing their utility as biolabels.     

Vibrational spectroscopic study of poly(dimethylsiloxane)-ZnO nanocomposites

A series of poly(dimethylsiloxane)-zinc oxide (PDMS-ZnO) nanocomposites having different concentrations of ZnO nanoparticles (0, 1, 5, 10 and 20 wt%) have been prepared. Raman and FTIR-ATR spectroscopic analysis was performed in order to determine the interaction between the ZnO nanoparticles and PDMS polymer matrix. Density functional theory (DFT) using the (B3-LYP)/6-311++G(2df,2p) method was used to investigate the vibrational spectra of PDMS. A complete vibrational assignment is supported by the normal coordinate analysis, calculated Raman activities as well as IR intensities.The presence of ZnO nanoparticles in PDMS gives rise to significant differences in relative intensities of the characteristic vibrational bands with respect to the cross-linked polymer. The changes in relative intensities of Raman bands, as well as swelling measurements, were used to explain the effect of ZnO nanoparticles on the cross-linked structure of PDMS nanocomposites. It is established that ZnO nanoparticles influence the cross-linking density of the polymer matrix.     

Dissolution of iron oxide nanoparticles inside polymer nanocapsules

The structure of poly(organosiloxane) nanocapsules partially filled with iron oxide cores of different sizes was revealed by small angle X-ray scattering and X-ray diffraction. The nanocapsules are synthesized by the formation of a poly(organosiloxane) shell around iron oxide nanoparticles and the simultaneous partial dissolution of these cores. Due to the high scattering contrast of the iron oxide cores compared to the polymer shell, the particle size distribution of the cores inside the capsules can be measured by small angle X-ray scattering. Additional information can be revealed by X-ray diffraction, which gives insights into the formation of the polymer network and the structure of the iron oxide cores. The study shows how the crystallinity and size of the nanoparticles as well as the shape and width of the size distribution can be altered by the synthesis parameters.     

Cross-linked polynorbornene-coated gold nanoparticles: dependence of particle stability on cross-linking position and cross-linker structure

This paper describes the preparation of cross-linked polynorbornene coated gold nanoparticles. The polymer was grown radially from the particle surface using a ring opening metathesis polymerization of norbornene and an electrophilic norbornene ester, which was cross-linked using a variety of diamines. The stability of the cross-linked nanoparticles toward oxidative etching by cyanide was evaluated. The rate of etching decreases as diamines with fewer degrees of conformational freedom are used as cross-linkers. The distance of the cross-linking block from the nanoparticle surface was systematically varied. Nanoparticles with the cross-linked block furthest from the surface were etched most slowly. This is suggested to arise as a result of the polymers adopting a mushroom conformation when the cross-linking block is close to the particle surface, while more distal cross-linking results in more rigid polymer chains that are less permeable to the cyanide etchant. These results provide new insight into how fine-tuning the polymer cross-linking architecture can modulate nanoparticle stability.