TiO2 coating of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

TiO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ materials were prepared by the hydrolyzation of Ti(OBu)₄. The impact of TiO₂ coating on the structure and electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ was investigated using X-ray diffraction, scanning electron microscope, and charge–discharge tests. The results indicated that TiO₂ coating did not affect the lattice of LiNi_1/3Co_1/3Mn_1/3O₂, but exhibited obvious effects on its discharge capacity and cycling stability. As coated TiO₂ increased from 0.0 to 2.0 mol%, the initial capacity of samples decreased slightly, but the cycling stability over 2.5∼4.3 V increased remarkably. The capacity retention reached 99.5% at the 50th cycle at a coating amount of 2.0 mol%.     

ZrO2 coating of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ materials were prepared by hydroxide precipitation. The structure and electrochemical properties of the ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ were investigated using X-ray diffraction, scanning electron microscope, and charge–discharge tests, indicating that the lattice structure of LiNi_1/3Co_1/3Mn_1/3O₂ were unchanged after the coating but the cycling stability was improved. As the coating amount increased from 0.0 to 0.5 mol.%, the initial capacity of the coated LiNi_1/3Co_1/3Mn_1/3O₂ decreased slightly; however, the cycling stability increased remarkably over the cut-off voltages of 2.5~4.3 V and the capacity retention reached 99.5% after 30 cycles at the coating amount of 0.5 mol.%. ZrO₂ coating also improved the cycling stability of LiNi_1/3Co_1/3Mn_1/3O₂ over wider cut-off voltage of 2.5~4.6 V.     

Organic acid assisted solid-state synthesis of Li1.2Ni0.16Co0.08Mn0.56O2 nanoparticles as lithium ion battery cathodes

Lithium-rich layered oxide Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ can be referred as a crystalline mixture of Li₂MnO₃ and LiNi_0.4Co_0.2Mn_0.4O₂ at equal molar ratio. In the paper, the solid state reaction of M(AC)₂·4H₂O (M = Mn, Co and Ni) and LiOH·H₂O has been performed to obtain nanocrystalline Li_1.2Ni_0.16Co_0.08Mn_0.56O₂ using a small molecular organic acid (i.e., oxalic acid (OA), citric acid (CA) or tartaric acid (TA)) as additive. The introduction of organic acids can help to improve the layered structure and inhibit the particle growth of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂, and the different organic acids exert distinct influences on the structural and electrochemical properties of Li_1.2Ni_0.16Co_0.08Mn_0.56O₂. In detail, the nanoparticles obtained in the presence of OA have the smallest average size of 50–150 nm, which correspondingly exhibit the highest initial discharge capacity of 267.52 mAh g⁻¹ at 0.1C and the best high-rate capability (e.g., 152.22 mAh g⁻¹, 5C) when applied as a lithium ion battery cathode. Furthermore, the active substance obtained from TA shows the best cycling stability and a discharge capacity of 202.42 mAh g⁻¹ can be retained after 50 cycles at 0.5C.     

Structural, transport and electrochemical properties of LiNi1 − yCoyMn0.1O2 and Al, Mg and Cu-substituted LiNi0.65Co0.25Mn0.1O2 oxides

LiNi_{1 - y − z}Co_yMn_zO₂ (y = 0.25, 0.35, 0.5, 0.6; z = 0.1, 0.2), LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂, LiNi_0.65Co_0.25Mn_0.08Al_0.02O₂, LiNi_0.65Co_0.25Mn_0.08Mg_0.02O₂ and LiNi_0.65Co_0.25Mn_0.08Al_0.01Mg_0.01O₂ cathode materials were synthesized by a soft chemistry EDTA-based method. Structural and transport properties of pristine and delithiated materials (Li_xNi_0.65Co_0.25Mn_0.1O₂, Li_xNi_0.55Co_0.35Mn_0.1O₂ and LiNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ oxides) are presented. In the considered group of oxides there is no correlation between electrical conductivity and the a parameter (M-M distance in the octahedra layers). The results of electrochemical performance of cathode materials are presented. The best stability during first 10 cycles was obtained for Li/Li_xNi_0.63Cu_0.02Co_0.25Mn_0.1O₂ cell due to enhanced kinetics of intercalation process.     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Preparation of LiNi0.5Mn0.5O2 cathode materials by urea hydrolysis coprecipitation

Layered LiNi_0.5Mn_0.5O₂ has been successfully synthesized via urea hydrolysis coprecipitation method. Well-crystallized LiNi_0.5Mn_0.5O₂ was obtained after calcinations of coprecipitation precursors and lithium salts at 450 °C for 3 h and following 900 °C for 10 h in air. Both the precursors and LiNi_0.5Mn_0.5O₂ powders show an agglomerated secondary structure with crystalline particles inside. The quasi-spherical morphology of the precursors was maintained during the calcinations. The first charge and discharge capacities of as-prepared LiNi_0.5Mn_0.5O₂ were 200 and 165mAh/g respectively. The discharge capacity of about 160mAh/g was retained after 10cycles for as-prepared samples.     

Electrochemical characterization of Mn: Co3O4 thin films prepared by spray pyrolysis via aqueous route

Present investigation reports, spray pyrolytic deposition of Mn: Co₃O₄ thin films onto the stainless steel by spray pyrolysis, at the deposition temperature 573 ± 2 K via aqueous route. Prepared electrodes were characterized structurally and morphologically by means of XRD and SEM. Also optical and electrochemical characterizations were carried out in depth. Structural characterization confirms face centered cubic and tetragonal body centered crystal structures for Co₃O₄ and Mn₃O₄ respectively. The rough granular morphology is observed form SEM. Electrochemical study reveals the pseudo capacitive as well as double layer behavior with optimum specific capacitance 485.29 F/g at the scan rate 1 mV/s in 1 M KOH electrolyte. Specific energy, specific power and columbic efficiency were calculated using chronopotentiometric technique. Electrochemical impedance spectroscopy was carried out in the frequency range 1 mHz–1 MHz. Randles equivalent circuit parameters associated with the operative cell are reported.     

Catalytic performance of Mn3O4 and Co3O4 nanocrystals prepared by sonochemical method in epoxidation of styrene and cyclooctene

A simple sonochemical method was developed to synthesis uniform sphere-like Co₃O₄ and Mn₃O₄ nanocrystals. Epoxidation of styrene and cyclooctene by anhydrous tert-butyl hydroperoxide over the prepared Co₃O₄ and Mn₃O₄ nanocatalysts was investigated. The results of conversion activity were compared with bulk Co₃O₄ and Mn₃O₄. Under optimized reaction conditions, the nanocatalysts showed a superior catalytic performance as compared to the bulk catalysts. Powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and BET surface area, were used to characterize and investigate the nanocatalysts.     

Flame synthesis of 5 V spinel-LiNi0.5Mn1.5O4 cathode-materials for lithium-ion rechargeable-batteries

The lithium transition metal oxide LiNi_0.5Mn_1.5O₄ with an space group (SG) structure has shown great potential as a cathode material for 5 V lithium-ion rechargeable-batteries. In this work, a flame-assisted spray technology (FAST) was developed to produce nanostructured LiNi_0.5Mn_1.5O₄ powder in a continuous manner. The as-synthesized powder had a uniform morphology, was spherical in shape and had a nanocrystalline structure, as observed by SEM and TEM. The XRD pattern of the as-synthesized powder matched the spectrum of spinel-LiNi_0.5Mn_1.5O₄. The average grain size was about 16 nm, as calculated by XRD. However, XRD also indicated the impurity Mn₂NiO₄ in the powder. By varying flame temperature, it was possible to show that the impurity was formed due to the high temperature of the flame. While flame temperature was minimized by lowering the H₂/N₂ ratio, it was not possible to completely eliminate Mn₂NiO₄ from the as-synthesized powder. After annealing at 800 °C for 2 h, the impurity was eliminated, and the XRD pattern of the powder indicated a pure-phase spinel structure with an SG. The electrochemical performance of the flame-synthesized LiNi_0.5Mn_1.5O₄ powder was tested in coin-type test batteries that were charged and discharged at constant current under a 5 V potential. The test cells showed the characteristic voltage plateaus of spinel-LiNi_0.5Mn_1.5O₄ ( SG). The material proved to be electrochemically active as a cathode material for lithium-ion rechargeable-batteries.     

High temperature and low current density synthesis of Mn3O4 porous nano spheres: Characterization and electrochemical properties

Uniform and single-crystalline Mn₃O₄ nano-spheres were synthesized by cathodic electrodeposition at high temperature (80 °C) and low current density (0.25 mA cm⁻¹) on steel electrode. Further the annealed samples were characterized for their structural and morphological properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Brunauer-Emmett-Teller (BET) studies. TEM and SEM images showed that particles have spherical shapes and the average diameter size was about 50 nm. Formation of Mn₃O₄ compound was confirmed from FTIR studies. The XRD pattern showed that the Mn₃O₄ exhibit tetragonal hausmannite structure. The results of N₂ adsorption-desorption analysis indicated that Mn₃O₄ nano-sphere has BET surface area of about 177.6 m² g⁻¹ and average pore diameters of 3 and 4 nm. The possible formation mechanism of Mn₃O₄ nanostructures has been discussed. The supercapacitive properties of Mn₃O₄ sample in 0.5 M Na₂SO₄ electrolyte showed maximum supercapacitance of 235.4 Fg⁻¹ at scan rate 10 mV s⁻¹. Coulumbic efficiency could be kept about 90% during 1000 cycles at 10 mV s⁻¹.     

Preparation and magnetic properties of the conductive Co(1−x)NixFe2O4/polyaniline microsphere composites

Core-shell Co_(1−x)Ni_xFe₂O₄/polyaniline nanoparticles, where the core was Co_(1−x)Ni_xFe₂O₄ and the shell was polyaniline, were prepared by the combination of sol-gel process and in-situ polymerization methods. Nanoparticles were investigated by Fourier transform spectrometer, X-ray diffraction diffractometer, Scanning electron microscope, Differential thermal analysis and Superconductor quantum interference device. The results showed that the saturation magnetization of pure Co_(1−x)Ni_xFe₂O₄ nanoparticles were 57.57 emu/g, but Co_(1−x)Ni_xFe₂O₄/polyaniline composites were 37.36 emu/g. It was attributed to the lower content (15 wt%), smaller size and their uneven distribution of Co_(1−x)Ni_xFe₂O₄ nanoparticles in the final microsphere composites. Both Co_(1−x)Ni_xFe₂O₄ and PANI/Co_(1−x)Ni_xFe₂O₄ showed superparamagnetism.     

Characterization of Na-substituted LiNi1/3Co1/3Mn1/3O2 cathode materials for lithium-ion battery

Highly crystalline layered Li_1?xNa_xNi_1/3Co_1/3Mn_1/3O₂ (x?=?0, 0.001, 0.01, 0.03, 0.05) materials are synthesized by molten salts method and characterized by scanning electron microscopy, inductively coupled plasma (ICP), X-ray diffraction, Rietveld refinement, and electrochemical measurement, respectively. ICP, SEM, and EDS results show that Na ions are incorporated in LiNi_1/3Co_1/3Mn_1/3O₂. Rietveld refinement results show that suitable Na substitution leads to stable layered structure by full Na occupying in Li layer and further attributes to low cation mixing. Electrochemical studies demonstrate that the Na-substituted LiNi_1/3Co_1/3Mn_1/3O₂ shows improved rate capability and cycling performance compared to that of pure LiNi_1/3Co_1/3Mn_1/3O₂.     

Charge-discharge characteristics of nanocrystalline Co3O4 powders via aerosol flame synthesis

Nanocrystalline Co₃O₄ powders were synthesized by aerosol flame synthesis (AFS) method for the anode of lithium ion batteries and the basic electrochemical properties were investigated. The effects of synthesis conditions and heat-treatment temperature on the morphology, crystallite size and electrochemical properties were investigated. As-prepared soot contained Co₃O₄, CoO and Co(OH)₂, which were eventually converted into cubic spinel Co₃O₄ by post heat treatment. The as-prepared particle size was in the range of 10-30 nm and grew to 50-85 nm by the heat treatment. With growing particle size and improved crystallinity, charge-discharge capacity and cycle performance were improved and the discharge capacity of the powder heat-treated at 700 °C was 571 mAh/g after 30 cycles, which was better than Co₃O₄ powder reported in the previous literature.     

High rate performance of Li[Ni1/3Co1/3Mn1/3]O2 synthesized via co-precipitation method by different precipitators

In the present study, we investigated the effect of three different precipitators (NaOH, Na₂CO₃ and (NH₄)₂CO₃) on the synthesized layered Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials via co-precipitation method. The obtained compounds were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and galvanostatic charge–discharge measurements. The XRD patterns analysis showed that all the resulted Li[Ni_1/3Co_1/3Mn_1/3]O₂ materials possess a layered hexagonal structure. It was found that at high discharge rate (2C), the prepared Li[Ni_1/3Co_1/3Mn_1/3]O₂ system using Na₂CO₃ as the precipitator exhibits better cycling performance in the charge–discharge tests compared to others, indicating that Na₂CO₃ is an optimum precipitator. After 100 cycles at 2C discharge rate in the voltage range from 2.8 to 4.5 vs. Li/Li⁺, the Li[Ni_1/3Co_1/3Mn_1/3]O₂ system using Na₂CO₃ as the precipitator retains 97% of its initial discharge capacity.     

A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.     

Capacity fading of LiCr0.1Mn1.9O4/MPCF cells at elevated temperature

Capacity fading of LiCr_0.1Mn_1.9O₄ /MPCF (mesophase pitch-based carbon fiber) cells was investigated at elevated temperature (55 °C). The cells showed very fast capacity fading, keeping only 60% of capacity retention at the 100th cycle at 55 °C. The cycled electrodes and the electrolyte were analyzed using electrochemical test, inductively coupled plasma, and X-ray diffraction. Results of the analyses indicated that LiCr_0.1Mn_1.9O₄ exhibited good effects on restraint of Mn dissolution and stabilization of structure at 55 °C. The cycled LiCr_0.1Mn_1.9O₄ electrode and the cycled MPCF electrode presented good electrochemical performance again with fresh electrolyte. Therefore, it was proposed that the cycling fading of LiCr_0.1Mn_1.9O₄/MPCF cells was mainly caused by decomposition of electrolyte upon LiCr_0.1Mn_1.9O₄ electrode during cycling. It was found that the decomposition of electrolyte led to the formation of a surface layer comprised of Li₂CO₃, Li _x PF _y , CH₃OCO₂Li or (CH₂OCO₂Li)₂, polymeric ether etc. The formation of this film consumed active lithium ions, leading to fast capacity fading of LiCr_0.1Mn_1.9O₄/MPCF cell at elevated temperature.     

LiNi1/3Co1/3Mn1/3O2 cathode materials for LIB prepared by spray pyrolysis I: the spectral, structural, and electro-chemical properties

Layered lithium ion battery cathode material LiNi_1/3Co_1/3Mn_1/3O₂ with uniform particle size of about 6 μm was synthesized by a spray pyrolysis method. Infrared and X-ray diffraction analyses show that the pyrolysis at 1,000 °C for 2 s in the tube furnace eliminates nearly all the organic components but is still not enough for the complete crystallization of LiNi_1/3Co_1/3Mn_1/3O₂ materials. Therefore, further annealing at 850 °C is needed. The prepared LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials show excellent electrochemical performances. By increasing the C-rates, the cell shows discharge capacities of 159.3, 148.2, 133.7, and 125.7 mAh g^?1 at 0.1, 0.2, 0.5, and 1C rates, respectively. Only 2.1 mAh g^?1 capacity loss is observed when back to 0.1C rate. Moreover, LiNi_1/3Co_1/3Mn_1/3O₂ cathode retains 96, 97.7, 97.1, 94.5, and 97.1 % of its initial discharge capacities after 20 cycles at 0.1, 0.2, 0.5, 1, and back to 0.1C rates, respectively. More than 97 % coulombic efficiencies are observed at all the current densities in 20 cycles.     

调控氧空位实现高比表面积Co3O4纳米片上的产氧反应

Electrochemical water splitting requires efficient water oxidation catalysts to accelerate the sluggish kinetics of water oxidation reaction. Here, we designed an efficient Co₃O₄ electrocatalyst using a pyrolysis strategy for oxygen evolution reaction (OER). Morphological characterization confirmed the ultra-thin structure of nanosheet. Further, the existence of oxygen vacancies was obviously evidenced by the X-ray photoelectron spectroscopy and electron spin resonance spectroscopy. The increased surface area of Co₃O₄ ensures more exposed sites, whereas generated oxygen vacancies on Co₃O₄ surface create more active defects. The two scenarios were beneficial for accelerating the OER across the interface between the anode and electrolyte. As expected, the optimized Co₃O₄ nanosheets can catalyze the OER efficiently with a low overpotential of 310 mV at current density of 10 mA/cm² and remarkable long-term stability in 1.0 mol/L KOH.     

Mössbauer and magnetic study of Co x Fe3--x O4 nanoparticles

Magnetic nanoparticles of cobalt ferrites Co _x Fe_3−x O₄ (x = 1 or 2) have been obtained either by mechanical milling or thermal treatment of pre-prepared layered double hydroxide carbonate x-LDH–CO₃. Mechanical milling of the 1-LDH–CO₃ leads to the large-scale preparation of nearly spherical nanoparticles of CoFe₂O₄, the size of which (5 to 20 nm) is controlled by the treatment time. Core-shell structure with surface spin-canting has been considered for the nanoparticles formed to explain the observed hysteresis loop shift (from ZFC–FC) in the magnetic properties. Annealing treatment of the 2-LDH–CO₃ below 673 K results in the formation of nearly spherical pure Co₂FeO₄ nanoparticles. At 673 K and above, the LDH decomposition leads to the formation of a mixture of both spinels phases Co₂FeO₄ and CoFe₂O₄, the amount of the latter increases with annealing temperature. Unusually high magnetic hardness characterized by a 22 kOe coercive field at 1.8 K has been observed, which reflects the high intrinsic anisotropy for Co₂FeO₄.     

Studies of the electrochemical properties and thermal stability of LiNi1/3Co1/3Mn1/3O2/LiFePO4 composite cathodes for lithium ion batteries

A series of LiNi_1/3Co_1/3Mn_1/3O₂/LiFePO₄ composite cathodes with the LiFePO₄ mass content ranging from 10 to 30 wt% were prepared by ball milling in order to combine the merits of layered LiNi_1/3Co_1/3Mn_1/3O₂ and olivine LiFePO₄. The structure and morphology of the samples were characterized by X-ray diffraction and scanning electron microscope. The composite cathodes exhibited improved electrochemical performance compared with pristine LiNi_1/3Co_1/3Mn_1/3O₂. Among all the composite cathodes, the one with 20 wt% of LiFePO₄ showed the best electrochemical performance in terms of discharge capacity, cycle stability, and rate capability. Electrochemical impedance spectroscopy showed that mixing of LiFePO₄ in LiNi_1/3Co_1/3Mn_1/3O₂ decreased the internal resistance of the electrode, retarded the formation of SEI film, and facilitated the charge transfer reaction. Differential scanning calorimetry showed that the composite cathode had better thermal stability than pristine LiNi_1/3Co_1/3Mn_1/3O₂.