TiO2微球的合成及其作为散射层在量子点敏化太阳能电池中的应用

以十六烷基三甲基溴化铵（CTAB）为模板剂,通过TiCl₄在乙醇水溶液中的直接水解,制备了介孔TiO₂微球. X射线衍射（XRD）结果表明所制备的微球晶型为金红石,扫描电镜（SEM）结果显示微球的直径大约为700 nm,由粒径约为16 nm的小颗粒堆积而成. 通过刮涂法制备了在TiO₂小颗粒层上涂覆有作为散射层的TiO₂微球和未涂覆微球的薄膜. 并通过化学浴沉积（CBD）的方法在膜上生长CdS/CdSe量子点,得到了量子点敏化太阳能电池（QDSCs）. 紫外吸收和漫反射结果表明,这种微球结构有利于量子点的沉积,具有较强的光散射作用,有效地增加了光线的收集,从而提高了电池的光电流,最终得到了4.5%的光电转换效率,比不加散射层的电池的效率高27.7%,也比利用传统散射层（由20 nm TiO₂ 小颗粒和400 nm TiO₂ 固体颗粒组成）的电池效率高10.2%. 我们把电池效率的提升归因于较强的光散射作用和较长的电子寿命.     

Synthesis, structural and photocatalytic studies of Mn-doped CdS nanoparticles

Mn-doped CdS nanoparticles (Cd_1?x Mn _x S; where x = 0.00–0.10) were synthesized by a chemical precipitation method. The synthesized products were characterized by X-ray diffraction (XRD), scanning electron microscope, transmission electron microscope (TEM), and UV–Vis spectrometer. The XRD and TEM measurements show that the size of crystallites is in the range of 10–40 nm. Optical measurements indicated a red shift in the absorption band edge upon Mn doping. The direct allowed band gaps of undoped and Mn-doped CdS nanoparticles measured by UV–Vis spectrometer were 2.3 and 2.4 eV at 400 °C, respectively. Photocatalytic activities of CdS and Mn-doped CdS were evaluated by irradiating the solution to ultraviolet light and taking methyl orange (MO) as organic dye. It was found that 5 mol% Mn-doped CdS bleaches MO much faster than undoped CdS upon its exposure to the ultraviolet light. The experiment demonstrated that the photo-degradation efficiency of 5 mol% Mn-doped CdS was significantly higher than that of undoped CdS.     

Uncovering the role of the ZnS treatment in the performance of quantum dot sensitized solar cells

Among the third-generation photovoltaic devices, much attention is being paid to the so-called Quantum Dot sensitized Solar Cells (QDSCs). The currently poor performance of QDSCs seems to be efficiently patched by the ZnS treatment, increasing the output parameters of the devices, albeit its function remains rather unclear. Here new insights into the role of the ZnS layer on the QDSC performance are provided, revealing simultaneously the most active recombination pathways. Optical and AFM characterization confirms that the ZnS deposit covers, at least partially, both the TiO(2) nanoparticles and the QDs (CdSe). Photoanodes submitted to the ZnS treatment before and/or after the introduction of colloidal CdSe QDs were studied by electrochemical impedance spectroscopy, cyclic voltammetry and photocurrent experiments. The corresponding results prove that the passivation of the CdSe QDs rather than the blockage of the TiO(2) surface is the main factor leading to the efficiency improvement. In addition, a study of the ultrafast carrier dynamics by means of the Lens-Free Heterodyne Detection Transient Grating technique indicates that the ZnS shell also increases the rate of electron transfer. The dual role of the ZnS layer should be kept in mind in the quest for new modifiers for enhancing the performance of QDSCs.     

Energy Relay from an Unconventional Yellow Dye to CdS/CdSe Quantum Dots for Enhanced Solar Cell Performance

A new design for a quasi‐solid‐state Forster resonance energy transfer (FRET) enabled solar cell with unattached Lucifer yellow (LY) dye molecules as donors and CdS/CdSe quantum dots (QDs) tethered to titania (TiO₂) as acceptors is presented. The Forster radius is experimentally determined to be 5.29 nm. Sequential energy transfer from the LY dye to the QDs and electron transfer from the QDs to TiO₂ is followed by fluorescence quenching and electron lifetime studies. Cells with a donor–acceptor architecture (TiO₂/CdS/CdSe/ZnS‐LY/S^2?‐multi‐walled carbon nanotubes) show a maximum incident photon‐to‐current conversion efficiency of 53 % at 530 nm. This is the highest efficiency among Ru‐dye free FRET‐enabled quantum dot solar cells (QDSCs), and is much higher than the donor or acceptor‐only cells. The FRET‐enhanced solar cell performance over the majority of the visible spectrum paves the way to harnessing the untapped potential of the LY dye as an energy relay fluorophore for the entire gamut of dye sensitized, organic, or hybrid solar cells.     

Ag2S quantum dot-sensitized WO3 photoelectrodes for solar cells

This work investigates the photovoltaic properties of new-architecture Ag₂S quantum dot-sensitized solar cells (QDSCs) fabricated on WO₃ electrodes. Liquid-junction Ag₂S QDSCs were fabricated from QDs synthesized using the successive ionic layer adsorption and reaction process. The optimal QDSC yielded an efficiency η of 0.20 % under a 100-mW/cm² light illumination. Coating the QDSC with a compact layer and a scattering layer improved η to 0.31 % with a short-circuit current density J _sc of 5.81 mA/cm² and an open-circuit voltage V _oc of 0.21 V. η increased to 0.53 % at a reduced 0.1 sun illumination with a J _sc of 1.11 mA/cm². The external quantum efficiency (EQE) spectrum covered the spectral range of 350–900 nm with a maximal EQE of 29 % at λ?=?650 nm. This work demonstrates the feasibility of the new-configuration Ag₂S QDSCs fabricated on WO₃ electrodes.     

Optimized Synthesis and Fluorescence Spectrum Analysis of CdSe Quantum Dots

An optimized synthesis route was applied for controlling the preparation of CdSe quantum dots (QDs) in an aqueous solution. Some key factors which influencing the properties of CdSe QDs, such as initial pH, stabilizers, ratio of precursor, etc. were investigated. The size, shape, crystal structure, and optical property of CdSe QDs were also characterized by TEM, XRD, UV-Vis, and fluorescence (FL) spectra. The result showed that high-quality cubic CdSe QDs with 3 nm were obtained. The experiments also confirmed that thioglycolic acid (TGA), under the conditions of weak acid, is a better stabilizer than others. The ratio of [Cd²⁺] to [SeSO₃ ^2?] played an important role in the formation of CdSe QDs. The mechanisms about the influence factors were also presented.     

A solid-state CdSe quantum dot sensitized solar cell based on a quaterthiophene as a hole transporting material

A hybrid quantum dot sensitized solar cell (QDSC) composed of CdSe quantum dots (QDs) as light harvesters and TiO(2) and 3,3'-didodecyl-quaterthiophene (QT12) as electron and hole conductors, respectively, has been fully processed in air. The sensitizer has been introduced into the TiO(2) nanoporous layer either by the successive ionic layer adsorption and reaction method or by attaching colloidal QDs either directly or through molecular cables (linkers). As previously observed for QDSCs based on liquid electrolytes, the efficiency depends on the way of QD attachment, the direct adsorption of QDs being the procedure yielding the best results. Thermal annealing was applied in order to enhance the device response under illumination. Remarkable open circuit potentials are attained (close to 1 V), leading to an efficiency of 0.34% (AM 1.5G) in initial tests. Although low, it ranks as one of the highest values reported for solid state QDSCs based on titanium dioxide and colloidal quantum dots.     

基于量子点涂料的柔性光阳极及碳基对电极的制备和优化

首先制备出量子点(QDs)/TiO_2涂料,分别采用丝网印刷法与刀刮法将涂料涂覆于ITO/PET柔性基底上,结果表明刀刮法制备量子点敏化太阳电池(QDSCs)效果更佳,且具有普适性。基于铜片对电极所组装的ZnCuInSe,CdSe和CdSeTe量子点半柔性QDSCs最高效率分别达2.83%,2.46%和1.99%。另外,我们对石墨纸进行表面化学修饰以提高亲水性,再通过简单的连续离子交换吸附法(SILAR)在石墨纸上负载Cu_xS纳米粒子,制备出Cu_xS/GP柔性对电极,进一步组装成全柔性QDSCs,获得了2.13%光电转化效率。     

基于量子点涂料的柔性光阳极及碳基对电极的制备和优化

首先制备出量子点（QDs）/TiO₂涂料,分别采用丝网印刷法与刀刮法将涂料涂覆于ITO/PET柔性基底上,结果表明刀刮法制备量子点敏化太阳电池（QDSCs）效果更佳,且具有普适性。基于铜片对电极所组装的ZnCuInSe,CdSe和CdSeTe量子点半柔性QDSCs最高效率分别达2.83%,2.46%和1.99%。另外,我们对石墨纸进行表面化学修饰以提高亲水性,再通过简单的连续离子交换吸附法（SILAR）在石墨纸上负载Cu_xS纳米粒子,制备出Cu_xS/GP柔性对电极,进一步组装成全柔性QDSCs,获得了2.13%光电转化效率。     

Surface‐State‐Mediated Charge‐Transfer Dynamics in CdTe/CdSe Core–Shell Quantum Dots

Herein, we report the synthesis of aqueous CdTe/CdSe type‐II core–shell quantum dots (QDs) in which 3‐mercaptopropionic acid is used as the capping agent. The CdTe QDs and CdTe/CdSe core–shell QDs are characterized by X‐ray diffraction (XRD), high‐resolution transmission electron microscopy (HR‐TEM), steady‐state absorption, and emission spectroscopy. A red shift in the steady‐state absorption and emission bands is observed with increasing CdSe shell thickness over CdTe QDs. The XRD pattern indicates that the peaks are shifted to higher angles after growth of the CdSe shell on the CdTe QDs. HR‐TEM images of both CdTe and CdTe/CdSe QDs indicate that the particles are spherical, with a good shape homogeneity, and that the particle size increases by about 2 nm after shell formation. In the time‐resolved emission studies, we observe that the average emission lifetime (τ_av) increases to 23.5 ns for CdTe/CdSe (for the thickest shell) as compared to CdTe QDs (τ_av=12 ns). The twofold increment in the average emission lifetime indicates an efficient charge separation in type‐II CdTe/CdSe core–shell QDs. Transient absorption studies suggest that both the carrier cooling and the charge‐transfer dynamics are affected by the presence of traps in the CdTe QDs and CdTe/CdSe core–shell QDs. Carrier quenching experiments indicate that hole traps strongly affect the carrier cooling dynamics in CdTe/CdSe core–shell QDs.     

Quantum dots co-sensitized solar cells: a new assembly process of CdS/CdSe linked to mesoscopic TiO2-nano-SiO2 hybrid film

A green and simple method was found to prepare CdS/CdSe co-sensitized photoelectrodes for the quantum dots sensitized solar cells application. All the assembly processes of CdS and CdSe quantum dots (QDs) were carried out in aqueous solution. CdS and CdSe QDs were sequentially assembled onto TiO₂-nano-SiO₂ hybrid film by two steps. Firstly, CdS QDs were deposited in situ over TiO₂-nano-SiO₂ hybrid film by the successive ionic layer adsorption and reaction (SILAR) process in water. Secondly, using 3-mercaptopropionic acid (3-MPA) as a linker molecule, the pre-prepared colloidal CdSe QDs (~3.0 nm) dissolved in water was linked onto the TiO₂-nano-SiO₂ hybrid film by the self-assembled monolayer technique with the mode of dropwise. The mode is simple and advantageous to saving materials and time. The results show that the photovoltaic performance of the cells is enhanced with the increase of SILAR cycles for TiO₂-nano-SiO₂/CdS photoelectrode. The power conversion efficiency of 2.15 % was achieved using the co-sensitization photoelectrode prepared by using 6 SILAR cycles of CdS plus CdSe (TiO₂-nano-SiO₂/CdS(6)/CdSe) under the illumination of one sun (AM1.5, 100 mW/cm²).     

Influence of different precursors and Mn doping concentrations on the structural,optical properties and photocatalytic activity of single-crystal manganese-doped ZnO

Mn-doped ZnO single-crystal micronuts were synthesized via hydrothermal method in an hexamethylenetetramine aqueous solution. These micronuts are of wurtzite crystal structure. The effects of Mn doping amount and precursor concentration on the structural, optical properties and photocatalytic activity have been investigated. The synthesized Mn-doped ZnO was characterized by X-ray powder diffraction, field emission scanning electron microscopy (FESEM), UV–Vis absorption and photoluminescence spectroscopy. The structural analyses based on X-ray diffraction revealed the absence of Mn-related secondary phases. According to FESEM results, the length of ZnO micronuts was in the range of 5–8 μm. The band gap energy increased on increasing Mn doping concentration. The photocatalytic activity was studied by degradation of methyl orange aqueous solution, which showed that the Mn-doped ZnO micronuts prepared in precursor concentration of 0.1 M and 4% Mn doping had the highest photocatalytic activity. The effects of crystal defect and band gap energy on photocatalytic activity of Mn-doped ZnO samples were studied in different precursors and Mn doping amounts.     

Graphene quantum dots assisted photovoltage and efficiency enhancement in CdSe quantum dot sensitized solar cells

CdSe quantum dot sensitized solar cells(QDSCs) modified with graphene quantum dots(GQDs) have been successfully achieved in this work for the first time. Satisfactorily, the optimized photovoltage(Voc) of the modified QDSCs was approximately 0.04 V higher than that of plain CdSe QDSCs, consequently improving the photovoltaic performance of the resulting QDSCs. Served as a novel coating on the CdSe QD sensitized photoanode, GQDs played a vital role in improving Vocdue to the suppressed charge recombination which has been confirmed by electron impedance spectroscopy as well as transient photovoltage decay measurements. Moreover, different adsorption sequences, concentration and deposition time of GQDs have also been systematically investigated to boost the power conversion efficiency(PCE) of CdSe QDSCs. After the coating of CdSe with GQDs, the resulting champion CdSe QDSCs exhibited an improved PCE of 6.59% under AM 1.5G full one sun illumination.     

Enhancing the device performance of a blue light‐emitting copolymer using CdSe/ZnS quantum dots

An alternating triarylamine‐functionalized fluorene‐based copolymer synthesized using a Suzuki–Miyaura cross‐coupling procedure is used as blue emitting layer in polymer light‐emitting diodes (PLEDs). Subsequently, the effects of CdSe/ZnS quantum dots (QDs) on the optoelectronic properties of the copolymer are investigated. Therefore, CdSe/ZnS QDs are embedded into the copolymer matrix and hybrid PLEDs are fabricated. The devices comprised of CdSe/ZnS QDs reveal enhanced performances, yielding about 3.4 times more luminous efficiency than that of the device without QDs. Further enhancement is achieved by using electron transport layer; the luminous efficiency rose from 0.065 to 1.740 cd A^?1 for the hybrid PLEDs, corresponding to a superb 27‐fold intensification of the efficiency. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 147–156     

The Application of CdSe Quantum Dots with Multicolor Emission as Fluorescent Probes for Cell Labeling

Herein, highly luminescent CdSe quantum dots (QDs) with emissions from the blue to the red region of visible light were synthesized by using a simple method. The emission range of the CdSe QDs could be tuned from λ=503 to 606 nm by controlling the size of the CdSe QDs. Two amino acids, L ‐tryptophan (L ‐Trp) and L ‐arginine (L ‐Arg), were used as coating agents. The quantum yield (QY) of CdSe QDs (green color) with an optimized thickness could reach up to 52 %. The structures and compositions of QDs were examined by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Optical properties were studied by using UV/Vis and photoluminescence (PL) spectroscopy and a comparison was made between uncoated and coated CdSe QDs. The amino acid‐modified β‐cyclodextrin (CD)‐coated CdSe QDs presented lower cytotoxicity to cells for 48 h. Furthermore, amino acid‐modified β‐CD‐coated green CdSe QDs in HepG2 cells were assessed by using confocal laser scanning fluorescence microscopy. The results showed that amino acid‐modified β‐CD‐coated green CdSe QDs could enter tumor cells efficiently and indicated that biomolecule‐coated QDs could be used as a potential fluorescent probe.     

Influence of highly efficient PbS counter electrode on photovoltaic performance of CdSe quantum dots-sensitized solar cells

PbS electrode with high catalytic activity to S_n ^2? reduction certificated by the measurements of electrochemical impedance spectroscopy and cyclic voltammetry was prepared by a simple method. The high catalytic activity makes it be a low-cost alternative counter electrode to platinum (Pt) to be used in quantum dots-sensitized solar cells (QDSSCs) based on polysulfide electrolyte. The photovoltaic performance enhancement of the quantum dots (QDs)-sensitized semiconductor thin films due to the PbS counter electrode was evaluated by fabricating QDSSCs based on CdSe QDs-sensitized ZnO (SnO₂) thin film. CdSe QDs-sensitized ZnO thin film has the lower internal total series resistance and electron transmission time, the higher electron lifetime and electron collection efficiency than the CdSe QDs-sensitized SnO₂ thin film. Replacing the Pt counter electrode with the PbS counter electrode leads to more improvement on the short circuit photocurrent density for QDSSC based on the ZnO thin film than the SnO₂ thin film. Therefore, the process to limit the photovoltaic performance of CdSe QDs-sensitized solar cell and the possible way to improve the photovoltaic performance were analyzed.     

Hot‐Hole Extraction from Quantum Dot to Molecular Adsorbate

Ultrafast thermalized and hot‐hole‐transfer processes have been investigated in CdSe quantum dot (QD)/catechol composite systems in which hole transfer from photoexcited QDs to the catechols is thermodynamically favorable. A series of catechol derivatives were selected with different electron‐donating and ‐withdrawing groups, and the effect of these groups on hole transfer and charge recombination (CR) dynamics has been investigated. The hole‐transfer time was determined using the fluorescence upconversion technique and found to be 2–10 ps depending on the molecular structure of the catechol derivatives. The hot‐hole‐transfer process was followed after monitoring 2S luminescence of CdSe QDs. Interestingly, hot‐hole extraction was observed only in the CdSe/3‐methoxycatechol (3‐OCH₃) composite system owing to the higher electron‐donating property of the 3‐methoxy group. To confirm the extraction of the hot hole and to monitor the CR reaction in CdSe QD/catechol composite systems, ultrafast transient absorption studies have been carried out. Ultrafast transient‐absorption studies show that the bleach recovery kinetics of CdSe QD at the 2S excitonic position is much faster in the presence of 3‐OCH₃. This faster bleach recovery at the 2S position in CdSe/3‐OCH₃ suggests hot‐hole transfer from CdSe QD to 3‐OCH₃. CR dynamics in CdSe QD/catechol composite systems was followed by monitoring the excitonic bleach at the 1S position and was found to decrease with free energy of the CR reaction.     

Recognition of DNA based on changes in the fluorescence intensity of CdSe/CD QDs–phenanthroline systems

The CdSe quantum dots (QDs) modified by mercapto-β-cyclodextrin (CD) were synthesized and characterized by transmission electron microscopy, powder X-ray diffraction, excitation and emission spectra, and fluorescence lifetime. When λ_ex = 370 nm, the fluorescence peak of CdSe/CD QDs is at 525 nm. Phenanthroline (Phen) is able to quench their fluorescence, which can be recovered by the addition of DNA. The quenching and restoration of fluorescence intensity were found to be linearly proportional to the amount of Phen and DNA, respectively. The variation of the fluorescence intensity of the CdSe/CD QDs–Phen system was studied, and it was demonstrated to result from a static mechanism due to the formation of a Phen inclusion complex with the CdSe QDs modified by mercapto-β-cyclodextrin. The fluorescence recovery was due to the binding of DNA with Phen in the inclusion complex, leading to the freeing of the CdSe/CD QDs. The binding constants and sizes of the binding sites of the Phen–DNA interaction were calculated to be 1.33 × 10⁷ mol^?1 L and 10.79 bp.     

基于血红蛋白/硒化镉量子点多层膜的H2O2生物传感器

合成了水溶性硒化镉(CdSe)量子点,利用组装技术和静电吸附作用,将带正电荷的血红蛋白(Hb)和带负电荷的CdSe量子点层层组装到壳聚糖(chit)修饰的玻碳电极(GCE)表面,构建基于{Hb/CdSe}n多层膜的无电子媒介体的电流型生物传感器({Hb/CdSe}3/chit/GCE).运用紫外-可见吸收光谱、电致化学发光、交流阻抗和循环伏安技术来表征修饰膜,并研究传感器的作用机理、性能及分析应用.结果表明:与量子点薄膜法及量子点/血红蛋白复合物法等固载血红蛋白的其他方法相比,层层组装法能显著提高血红蛋白的固定量,保持血红蛋白的生物活性,增强传感器的灵敏度和稳定性.传感器检测H2O2的线性范围为4.0×10-8～4.8×10-6 mol·L-1(r=0.999 1),检测限为2.0×10-8mol·L-l.多层膜的电致化学发光研究,表明修饰电极有望用于电致化学发光传感器的制备.     

Effect of P-Containing Ligands on the Structural and Optical Properties of (CdSe)<Subscript>n</Subscript> (n = 3, 6, 10) Clusters

The effect of phosphorus-containing ligands on the structure, energetics and properties of the (CdSe)_n clusters (n = 3, 6, and 10) with different number of PH₃ and PMe₃ ligands were studied by using density functional theory calculations. The P atom in the ligand interacts with Cd and forms a strong Cd–P coordination bond. The introduction of ligands does not change the cluster architecture, but leads to considerable changes in Cd–Se bondlength, charge distribution, binding energy, HOMO–LUMO gap and optical absorption. The ligand influence is enhanced with increasing ligand coverage. A blueshift in absorption band was predicted for the clusters with increasing ligands, resulting from the electron donating characteristics of the ligands that hamper electron transition from Se to Cd. As P-containing ligands are often used in the preparation of CdSe nanocrystals, our calculations reveal the influence of ligand-cluster interaction on the cluster geometrical and electronic properties, which would be helpful for the nanocrystal design and synthesis.