Studies on TiO2/SiO2 and Pd/TiO2/SiO2 Catalysts in Photoreduction of CO2 with H2O to Methanol

The development of industry induced a massive increase in the emission of carbon dioxide into the atmosphere. A large amount of CO₂ and its general availability causes that it could be a cheap reactant in a reaction that runs in a way similar to photosynthesis in plants. Pure TiO₂ and metal doped TiO₂ are the most studied semiconductor catalysts for photoreduction of CO₂. The TiO₂/SiO₂ and Pd/TiO₂/SiO₂ catalysts were prepared and studied by temperature-programmed desorption, X-ray diffraction analysis, SEM-EDS, temperature-programmed reduction and then used for the methanol synthesis. The photoactivity of Pd/TiO₂/SiO₂ catalysts in the reduction of CO₂ with H₂O was tested at room temperature using photoreactor equipped with 16 lamps. The wavelength was characteristic of near ultraviolet. Post-reaction products were identified with gas chromatograph equipped with the flame ionization detector. Pd doping made the catalysts photoactive and the photoactivity of catalysts was changing as follows: 1%Pd/5%TiO₂/SiO₂ > 1% Pd/10% TiO₂/SiO₂ > 1% Pd/15% TiO₂/SiO₂. Optimum ultraviolet radiation time in the photoreduction of CO₂ to methanol was 7 h. An addition of Pd does not change the surface of the carrier.     

Interaction of components in the HgBr2-CdBr2-PbBr2 ternary system

The interaction in the HgBr₂-CdBr₂-PbBr₂ ternary system was studied by differential thermal analysis; the isoconcentration section of the system at 50 mol % CdBr₂ was investigated. Based on the results of the study, a projection of the liquidus surface of the HgBr₂-CdBr₂-PbBr₂ ternary system to the composition triangle was constructed; the boundaries of the primary crystallization fields were determined for three phases: HgBr₂ (degenerate field), solid solution α based on CdBr₂, and solid solution β based on PbBr₂; and isotherms were drawn. A ternary eutectic has the composition 93 mol % HgBr₂-1 mol % CdBr₂-6 mol % PbBr₂ and melts at 235°C.     

Cp2TiCl2-catalyzed synthesis of tetraalkyl-substituted pyrazines by the reaction of nitriles with EtAlCl2 and Mg

Tetraalkyl-substituted pyrazines were obtained by the multicomponent reaction of aliphatic linear nitriles with EtAlCl₂ in the presence of Mg and Cp₂TiCl₂ catalyst in 60–91% yields. The same processing of isobutyronitrile gave 2,4,5-triisopropyl-1H-imidazole in 56% yield.     

Photocatalytic reduction of nitrate over TiO2 and Ag-modified TiO2

This research work presents the efficiency of the TiO₂ and Ag–TiO₂ thin films prepared by the sol–gel method and coated onto the surface of 304 stainless steel sheets used in the photocatalytic nitrate reduction processes. The Ag–TiO₂ thin films had the weight by weight (w/w) ratio of Ag⁺/TiO₂ of 0.1% as Ag atom. The XRD results showed that the crystalline phase structure of TiO₂ on the Ag–TiO₂ thin films was anatase. The optical band gaps of the TiO₂ and 0.1% Ag–TiO₂ thin films were respectively 3.27 and 2.70 eV, while the surface of the prepared catalysts was hydrophobic with the respective average water contact angles of 94.8° and 118.5° for the TiO₂ and 0.1% Ag–TiO₂ thin films. The net efficiencies of photocatalytic nitrate reduction of TiO₂ and 0.1% Ag–TiO₂ were 41.4% and 70.0%, respectively. The loading of Ag only influenced the nitrate removal efficiency without affecting the stoichiometric ratio of formate to nitrate. The net stoichiometric ratio of formate to nitrate of all experiments was 2.8:1.0, which is close to the stoichiometric ratio of 2.5:1.0 of the nitrate reduction to nitrite and then to nitrogen gas.     

A study of non-isothermal kinetics of limestone decomposition in air (O2/N2) and oxy-fuel (O2/CO2) atmospheres

The non-isothermal experiments of limestone decomposition at multi-heating rates in O₂/N₂ and O₂/CO₂ atmospheres were studied using thermogravimetry. The limestone decomposition kinetic model function, kinetic parameters of apparent activation energy (E), and pre-exponential factor (A) were evaluated by Bagchi and Malek method. The results shown that in 20 % O₂/80 % N₂ atmosphere, the limestone decomposed slowly following the contracting sphere volume model controlled by boundary reaction (spherical symmetry) in two stages, and the E increased by about 50 kJ mol^?1 in the second decomposition stage. But in 20 % O₂/80 % CO₂ atmosphere, the presence of high-concentration CO₂ significantly inhibited the limestone decomposition, and made the decomposition process occur at high temperature with a rapid rate; the decomposition kinetics was divided into three stages, the first stage was an accelerated decomposition process following the Mampel Power law model with the exponential law equation, the second stage followed the nth order chemical reaction model as an α–t deceleration process, and the third stage belonged to the random nucleation and nuclei growth model with the Avrami–Erofeev equation. And with the heating rate increasing, the reaction order n showed a slight rise tendency. The E was about 1,245 kJ mol^?1 in 20 % O₂/80 % CO₂ atmosphere, but was only about 175 kJ mol^?1 in 20 % O₂/80 % N₂ atmosphere. The E and A increased markedly in the O₂/CO₂ atmosphere.     

可循环利用的固体氧化剂两相氧化偶联合成2-氨基-2'-羟基-1,1'-联萘的研究

采用浸渍法制备了不同负载量的FeCl₃/Al₂O₃固体氧化剂, 并考察了载体和溶剂对氧化2-萘胺和2-萘酚交叉偶联的影响. 结果表明: 在60 ℃, 氯苯作溶剂的情况下, 含TiO₂ (质量分数)5%的载体, 负载10% FeCl₃时2-氨基-2'-羟基-1,1'-联萘(NOBIN)的收率最高达到了95.01%; 用过的固体氧化剂经H₂O₂氧化处理后活性明显恢复, 证明此法是一条循环再生的有效途径.     

Oxidation of 2-cyanoprop-2-enethioamides with hydrogen peroxide

Oxidation of (E)-3-aryl-2-cyanoprop-2-enethioamides with 32% H₂O₂ under mild conditions gave (E)-3-aryl-2-cyano-1-iminioprop-2-ene-1-sulfenates in 70–88% yields. Under the conditions of the Radziszewski reaction (H₂O₂, 10% aqueous KOH) or upon prolonged treatment with H₂O₂, (E)-3-aryl-2-cyanoprop-2-enethioamides underwent transformations leading to complex mixtures of oxidation products. In some cases, 3-aryloxirane-2,2-dicarboxamides were isolated from those mixtures in low yields (<20%). Treatment of 3-arylamino-2-cyanoprop-2-enethioamides with the system H₂O₂/KOH in ethanol afforded (arylaminomethylidene)malononitriles.     

Investigation of RuO2-IrO2-SnO2 thin film evolution

The thermal evolution process of RuO₂–IrO₂–SnO₂ mixed oxide thin films of varying noble metal contents has been investigated under in situ conditions by thermogravimetry-mass spectrometry (TG-MS), infrared emission spectroscopy (IR) and cyclic voltammetry (CV). The gel-like films prepared from aqueous solutions of the precursor compounds RuOHCl₃, H₂IrCl₆ and Sn(OH)₂(CH₃COO)_2–xCl_x on titanium metal support were heated in an atmosphere containing 20% O₂ and 80% Ar up to 600°C. Chlorine evolution takes place in a single step between 320 and 500°C accompanied with the decomposition of the acetate ligand. The decomposition of surface species formed like carbonyls, carboxylates and carbonates occurs in two stages between 200 and 500°C. The temperature of chlorine evolution and that of the final film formation increases with the increase of the iridium content in the films. The anodic peak charge shows a maximum value at 18% iridium content.     

Preparation of ethyl levulinate from wheat stalk over Zr(SO4)2/SiO2

A series of Zr(SO₄)₂/SiO₂ solid acid catalysts with different Zr(SO₄)₂ loadings were prepared by water-soluble-impregnation method at room temperature. Then, the prepared catalysts were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy and energy-dispersive X-ray spectrum, X-ray diffraction, adsorption/desorption of N₂, and temperature-programmed desorption of NH₃. The results showed that the active component Zr(SO₄)₂ was successfully adhered to the mesoporous SiO₂, and the acid amount of Zr(SO₄)₂/SiO₂ increased with the increasing of the Zr(SO₄)₂ loadings. Finally, the wheat stalk was used as raw material and depolymerized over Zr(SO₄)₂/SiO₂ to produce ethyl levulinate (EL). The reaction mixture was separated and purified by filtration and vacuum distillation. The kinetic characteristics and the reaction pathway were also studied. A comparative study showed that 20 wt.% Zr(SO₄)₂/SiO₂ exhibited higher catalytic activity. When reaction temperature, time, catalyst dosage and Zr(SO₄)₂ loadings were 190 °C, 50 min, 20 wt.% and 30 wt.%, the EL yield reached a maximum of 17.14%. The relative content of EL exceeded 90% after three steps of distillation.     

Study of properties of Al2O3 and TiO2 supported palladium catalysts in reactions of tetrachloromethane hydrogenation

Properties of Al₂O₃- and TuO₂-supported palladium catalysts modified with calcium oxide were studied. Catalyst samples 2% Pd/CaO-TiO₂ and 2% Pd/CaO-Al₂O₃ were examined by the methods of temperature-programmed reduction in a flow of hydrogen, temperature-programmed desorption of ammonia and carbon(IV) oxide, and X-ray diffraction analysis.     

溶剂热法合成Fe-CeO2与N-Fe-CeO2纳米粉体及其光催化性能

采用溶剂热法合成了不同Fe掺杂含量的Fe-CeO₂纳米粉体及不同氮源掺杂的N-10% Fe-CeO₂（n_Fe/（n_Fe+n_Ce）=10%）纳米粉体。利用TEM、XRD、XPS、Raman和UV-Vis等技术对其微观结构与形貌进行了表征,并通过降解亚甲基蓝溶液对其光催化性能进行了研究。结果表明,Fe掺杂可以提高CeO₂的光催化性能,以10% Fe-CeO₂催化效率最高,对亚甲基蓝的降解率从纯CeO₂的67%提高到95%。而N的掺杂可调节10% Fe-CeO₂催化性能。以浓氨水为氮源的N-10% Fe-CeO₂（NH₃·H₂O-N-10% Fe-CeO₂）的降解率可进一步提高到97%,并且具有较好的稳定性,经5次循环使用,对亚甲基蓝的光催化降解率仍高达89%。CeO₂催化活性的提高主要由于掺杂Fe和N改变了CeO₂的晶体结构与能带结构,促进了光生电子与空穴的产生与催化反应。     

Phase equilibria in the KCl-KBO2-K2CO3-K2MoO4 quaternary system

The phase diagram of the quaternary system KCl-KBO₂-K₂CO₃-K₂MoO₄ was studied by a calculation-experimental method and differential thermal analysis. Analytical models of phase equilibrium states were obtained, and the coordinates of a quaternary eutectic were determined: 550°C, 50% KCl, 8% KBO₂, 23% K₂CO₃, and 19% K₂MoO₄.     

The reactions between SO2 and C2H2 (and C2H4) at elevated temperatures. A single-pulse shock tube investigation

The high-temperature reaction between sulfur dioxide and acetylene in an excess of argon was studied in a 1?in. i.d. single-pulse shock tube. Mixtures ranging from 1.81% to 5.40% SO₂ and 1.60% to 4.90% C₂H₂ were heated to reflected shock temperatures of 1550°–2150°K, for dwell times of about 0.6 msec and gas dynamically quenched. Total reaction densities were 0.89 to 5.4 × 10^?2 moles/1. The reaction products were analyzed by gas chromatography. A technique was developed for separating Ar, C₂H₄, C₂H₂, SO₂, CO, CO₂, H₂S, COS, and CS₂. The major products of the reaction are CO, H₂, CS₂, and sulfur. The products observed were compared with those predicted on the assumption that equilibrium was attained. Several preliminary experiments were carried out with ethylene-sulfur dioxide mixtures, and the results indicated that for this combination the sulfur dioxide probably reacted with the acetylene generated from the decomposition of the ethylene, rather than directly with the ethylene. The rate of decline in the sulfur dioxide content in C₂H₂-SO₂ mixtures was found to be approximately second order (total) and can be empirically represented by A mechanism is proposed to account for the overall reaction kinetics.     

Influence of TiO2 on the Chemical,Mechanical, and Gas Separation Properties of Polyvinyl Alcohol-Titanium Dioxide (PVA-TiO2) Nanocomposite Membranes

PVA/TiO₂ nanocomposite membranes developed were investigated for chemical, mechanical, and gas separation properties. PVA/TiO₂ dispersion offers good optical property and less aggregation, as shown by UV-vis photospectroscopy. FT-IR spectra suggest strong interaction between PVA and TiO₂. Mechanical properties of the composite membranes were enhanced by the addition of TiO₂. Permeation results show that the addition of TiO₂ up to 20 wt.% increased the selectivity of gas pairs O₂/N_2, H₂/N_2, H₂/CO₂, and CO₂/N₂ by 60%, 55%, 23%, and 26% respectively, with a corresponding decrease in the permeability. At higher loading of TiO_2, a reverse trend was observed.     

Phase equilibria in the KCl-KBO2-K2CO3-K2WO4 quaternary system

The phase diagram of the KCl-KBO₂-K₂CO₃-K₂WO₄ quaternary system was studied by a calculation-experimental method and differential thermal analysis. Analytical models of phase equilibrium states were obtained, and the coordinates of a quaternary eutectic were determined: 545°C, 50 mol % KCl, 8 mol % KBO₂, 22.5 mol % K₂CO₃, and 19.5 mol % K₂WO₄.     

Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

LiF-LiBr-LiVO3-Li2MoO4-Li2SO4 quinary system

Phase equilibria in the LiF-LiBr-LiVO₃-Li₂MoO₄-Li₂SO₄ quinary system were studied by differential thermal analysis. A eutectic composition was determined to be 4.0 mol % LiF, 38.4 mol % LiBr, 30.8 mol % LiVO₃, 19.2 mol % Li₂MoO₄, and 7.6 mol % Li₂SO₄ with a melting point of 372°C and an enthalpy of melting of 164 ± 7 kJ/kg.     

Effects of CeO_2 preparation methods on the catalytic performance of MoO_3/CeO_2 toward sulfur-resistant methanation

CeO_2 supports were prepared by calcination or precipitation method and 5% MoO_3/CeO_2 catalysts were prepared by incipient-wetness impregnation method. The catalytic performance of the 5% MoO_3/CeO_2 catalysts toward sulfur-resistant methanation was investigated. The results showed that the Mo/Ce-1 catalysts with CeO_2 support prepared by calcination method exhibited the best sulfur-resistant methanation activity and stability with CO conversion as high as 75% while the Mo/Ce-3 catalysts the poorest. The supports and catalysts were characterized by N_2-adsorption–desorption, temperature-programmed reduction(TPR), X-ray diffraction(XRD), Raman spectroscopy(RS) and scanning electron microscope(SEM). The results indicated that the saturated monolayer loading MoO_3 on Ce-3 support was lower than 5% and there were some crystalline MoO_3 particles on the surface of the Mo/Ce-3. The preparation method of CeO_2 had a big influence on the specific surface area, the crystalline of CeO_2, and the catalytic performance of the corresponding Mo-based catalyst for sulfur-resistant methanation.     

溶剂热法合成Fe-CeO2与N-Fe-CeO2纳米粉体及其光催化性能

采用溶剂热法合成了不同Fe掺杂含量的Fe-CeO_2纳米粉体及不同氮源掺杂的N-10%Fe-CeO_2(n_(Fe)/(n_(Fe)+n_(Ce))=10%)纳米粉体。利用TEM、XRD、XPS、Raman和UV-Vis等技术对其微观结构与形貌进行了表征,并通过降解亚甲基蓝溶液对其光催化性能进行了研究。结果表明,Fe掺杂可以提高CeO_2的光催化性能,以10%Fe-CeO_2催化效率最高,对亚甲基蓝的降解率从纯CeO_2的67%提高到95%。而N的掺杂可调节10%Fe-CeO_2催化性能。以浓氨水为氮源的N-10%Fe-CeO_2(NH_3·H_2O-N-10%Fe-CeO_2)的降解率可进一步提高到97%,并且具有较好的稳定性,经5次循环使用,对亚甲基蓝的光催化降解率仍高达89%。CeO_2催化活性的提高主要由于掺杂Fe和N改变了CeO_2的晶体结构与能带结构,促进了光生电子与空穴的产生与催化反应。