氧化石墨烯基钴卟啉复合材料的电催化析氢反应

制备了5,10,15,20-四(苯基)卟啉钴配合物(CoTPP), 并利用该配合物与氧化石墨烯(GO)的π?π堆积作用组装了CoTPP/GO电催化产氢复合材料. 研究发现, 当CoTPP与GO的质量比为1∶15时, 复合材料的性能最佳. 该材料的拉曼和扫描电子显微镜结果显示, 与GO相比, CoTPP/GO复合材料表面的无序程度增加, 形貌改变有利于促进反应体系的电荷迁移与分离; 交流阻抗测试结果显示, 阻抗值由GO的1180 Ω降低为CoTPP/GO材料的734 Ω; 电化学测试结果显示, 析氢起始过电位由-761 mV降低为-337 mV, 塔菲尔斜率由296 mV/dec 降低至174 mV/dec, 法拉第效率却由23%提高至87%. 加入二苯硫醚(SPh₂)轴向配体后, CoTPP(SPh₂)/GO材料的析氢起始过电位进一步降低至-235 mV, 塔菲尔斜率降低至163 mV/dec, 法拉第效率提高至94%. 研究结果表明, 通过氧化石墨烯与金属卟啉的非共价键自组装是构筑石墨烯基电催化产氢材料的一个有效途径.     

Electrocatalysis of the Oxygen Reaction on Electrodes Prepared Using Disperse Synthetic Diamond Promoted with Cobalt Porphyrin and Its Pyropolymer

The oxygen electroreduction in acid solutions on electrodes of disperse synthetic diamond powder promoted with cobalt tetra(p-methoxyphenyl)porphyrin or its pyrolysis products is studied. A floating gas-diffusion electrode and an RDE of isotropic pyrocarbon are used in experiments; in the latter case, the catalyst is immobilized in a Nafion solution. Two types of diamond, with specific area of 5.8 and 170 m²/g, are used. The results are compared with similar data found for promoted acetylene black. A significant effect of the carbon support on electrocatalytical properties of cobalt porphyrin pyrolyzed on it is found.     

Imine Gels Based on Ferrocene and Porphyrin and Their Electrocatalytic Property

A series of porphyrin‐based imine gels have been synthesized via dynamic covalent gelation between 5,10,15,20‐tetra(4‐aminophenyl)‐21H,23H‐porphyrin (H₂TAPP) derivatives and various aldehyde compounds. The porphyrin‐ferrocene imine gels based on MTAPP (M=H₂, Ni²⁺, Co²⁺, Pd²⁺ and Zn²⁺) and ferrocene‐1,1′‐dicarbaldehyde (NA) display efficient HER, OER and ORR activities in alkaline media. Among the gels, CoTAPP‐NA shows an HER current density of 10 mA cm^?2 at low overpotential of 470 mV and small Tafel slope of 110 mV decade^?1 in alkaline media. CoTAPP‐NA also exhibits OER catalytic activity with low overpotential (416 mV for 10 mA cm^?2). CoTAPP‐NA shows ability in overall water splitting in alkaline media. In addition, CoTAPP‐NA exhibits onset potential (E_p) of 0.95 V and half‐wave potential (E_1/2) of 0.84 V in 1.0 mol L^?1 KOH solution for oxygen reduction. Moreover, the gel catalyst shows good stability.     

基于Nafion-L-赖氨酸-溶胶-凝胶膜的电催化型多巴胺传感器

基于Nafion-L-赖氨酸-溶胶-凝胶膜的电催化型多巴胺传感器     

Electrocatalytic Reduction of Dioxygen on the Surface of Glassy Carbon Electrodes Modified with Cobalt Porphyrin Complexes

The preparation and electrocatalytic behavior of glassy carbon electrodes modified with three different cobalt porphyrin complexes were investigated. The electrocatalytic ability of the modified electrodes for the reduction of dioxygen to hydrogen peroxide and water in air‐saturated aqueous solutions was examined by cyclic voltammetry and chronoamperometry techniques. The porphyrin‐adsorbed glassy carbon electrodes possess excellent electrocatalytic abilities for dioxygen reduction with overpotential about 0.5 V lower than that at a plain glassy carbon electrode. The experimental parameters were optimized and the mechanism of the catalytic process was discussed. The possible effects of the electron‐donating properties of groups in the meso‐position of the porphyrin ring were investigated.     

Preparation,Characterization, and Electrocatalytic Properties of Cobalt Oxide and Cobalt Hexacyanoferrate Hybrid Films

Polynuclear mixed‐valent films of cobalt oxide and cobalt hexacyanoferrate (CoOCoHCF) have been deposited on electrode surfaces from a solution of Co²⁺ and Fe(CN)₆^3? ions by repetitive potential cycling method. Simultaneous cyclic voltammetry and electrochemical quartz crystal microbalance measurements demonstrate the steady growth of modified film. The effect of type of monovalent cations as well as acidity of the supporting electrolyte on film growth and redox behavior of resulting film was investigated. In pure supporting electrolyte, electrochemical responses of modified electrode resemble with that of a surface immobilized redox couple. The hybrid film electrodes showed electrocatalytic activity toward oxidation of NADH, hydrazine and hydroxylamine. The feasibility of using our modified electrodes for analytical application was also explored.     

耐用钴卟啉修饰电极为基底的葡萄糖酶电极的研究

本文以热处理方法制得的四苯基钴卟啉化学修饰电极为换能器,制备了一种新型葡萄糖酶电极。该传感器的使用寿命几乎不受测量次数的影响,抗干扰能力强,葡萄糖浓度在9.0×10~(-5)～1.3×10~(-3)mol/L范围内有线性响应,响应时间3s。     

四(3,4-二甲基苯基)卟啉钴的合成及其光学性质

采用“两步法”,以吡咯和3,4-二甲基苯甲醛为原料,合成了四(3,4-二甲基苯基)卟啉(TDMPP, 1); 1与四水醋酸钴经络合反应合成四(3,4-二甲基苯基)卟啉钴(TDMPPCo, 2),其结构经¹H NMR, IR和荧光光谱确证。考察了金属盐的预处理、反应物浓度、浓缩比和投料比对合成2的收率影响。实验结果表明：在最佳反应条件［γ=n(1)：n(四水乙酸钴)=1 ：7, c（1）为22.95 mmol·L^-1,回流（150 ℃）反应4 h,浓缩比η为75%］下,收率可达82%。     

Electrocatalytic Reduction of Oxygen at Multi‐Walled Carbon Nanotubes and Cobalt Porphyrin Modified Glassy Carbon Electrode

The multi‐walled carbon nanotubes (MWNTs) modified glassy carbon electrode exhibited electrocatalytic activity to the reduction of oxygen in 0.1 M HAc‐NaAc (pH 3.8) buffer solution. Further modification with cobalt porphyrin film on the MWNTs by adsorption, the resulted modified electrode showed more efficient catalytic activity to O₂ reduction. The reduction peak potential of O₂ is shifted much more positively to 0.12 V (vs. Ag/AgCl), and the peak current is increased greatly. Cyclic voltammetry (CV), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM), were used to characterize the material and the modified film on electrode surface. Electrochemical experiments gave the total number of electron transfer for oxygen reduction as about 3, which indicated a co‐exist process of 2 electrons and 4 electrons for reduction of oxygen at this modified electrode. Meanwhile, the catalytic activities of the multilayer film (MWNTs/CoTMPyP)_n prepared by layer‐by‐layer method were investigated, and the results showed that the peak current of O₂ reduction increased and the peak potential shifted to a positive direction with the increase of layer numbers.     

New Composite Proton-Conducting Membranes Based on Nafion and Cross-Linked Sulfonated Polystyrene

New composite membranes based on commercial perfluorinated Nafion-115 membrane and cross-linked sulfonated polystyrene were synthesized and investigated. The membranes were prepared by radical polymerization of styrene in the presence of a cross-linking agent divinylbenzene in Nafion polymer matrix and subsequent sulfonation of formed polystyrene. The membranes containing approximately 5 and 10 wt % of cross-linked polystyrene with ion-exchange capacity of 1.1 to 1.3 mg-eq/g were obtained. Modification with sulfonated polystyrene leads to an increase in the moisture content and proton conductivity of membranes in the humidity range of 15 to 100 RH.     

Electrocatalytic Oxidation of NADH Based on Self-assembled Colloidal Gold and Nafion Matrixes and Co Complex Mediator

Nicotinamide adenine dinucleotide (NAD ) and its reduced form NADH used as coenzymes by over 300 dehydrogenases have been the subjects of numerous studies. Direct oxidation of NADH at a bare electrode only proceeds at high overpotentials, which finally le…     

Electrochemical Properties of Carbon Black AD-100 and AD-100 Promoted with Pyropolymer of Cobalt Tetra(p-methoxyphenyl)porphyrin

Carbon black AD-100: initial, activated, and promoted with pyropolymer of cobalt tetra(p-methoxyphenyl)porphyrin is characterized by a complex of electrochemical (floating electrode, rotating disk electrode, rotating ring-disk electrode, electrochemical impedance) and structural (standard porosimetry, BET) methods of investigation. Procedures for the AD-100 activation and promotion and the preparation of thin layers of the material to be studied and deposited on disk electrodes are described. The effect of the activation and promotion of carbon black on the surface and electrocatalytic activity of materials under study in the reduction of oxygen and hydrogen peroxide is shown. The ratio of constants of oxygen reduction directly to water and through intermediate formation of hydrogen peroxide is determined. A path for the oxygen reduction is discussed.     

Synthesis of Axially Coordinated Cobalt Porphyrin/graphene Oxide Nanocomposite for Enhanced Electrocatalytic CO2 Reduction to CO

The electrocatalysts containing cobalt-pyrrolic nitrogen-carbon （Co-N₄-C） moiety for CO₂ reduction reaction （CO₂RR） have caught much attention.However,the effects of Co valence state and its synergy with graphene substrate are not clear yet.In this work,cobalt porphyrin （Co TPP） molecule with the intrinsic Co-N₄-C moiety is successfully combined with graphene oxide （GO） via three kinds of liquid-phase methods.The ratio of Co TPP to GO and the valence s...     

一氧化氮在Nafion—钴席夫碱膜修饰电极上的电催化氧化及其测定

将一种杂环席夫碱N,N′－2,6－二乙酰吡啶缩双苯胺和Nafion修饰在铂电极上,然后与钴（Ⅱ）反应,得到Nafion－钴席夫碱膜修饰电极。实验结果表明,该修饰电极具有良好的机械、化学和电化学稳定性,对生物分子一氧化氮的电化学氧化有显著的催化作用。以1.5次微分线性扫描伏安法测定一氧化氮,当浓度在2.8×10     

ZIF67衍生硫化钴/多孔碳复合催化剂的制备及其电催化性能

采用离子交换法与热处理相结合的方法,以ZIF67为前驱体,硫代乙酰胺为硫源,制备出硫化钴/多孔碳(CoS/C)复合催化材料,并探讨了硫化时间对复合催化剂的形貌、结构及其氧还原(ORR)性能的影响。采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射仪(XRD)、N2吸附-脱附测定仪、X射线光电子能谱分析(XPS)、拉曼光谱仪(Raman)和旋转圆盘电极(RDE)技术表征催化剂的物理特征和电催化性能。研究结果显示,在碱性条件下该复合催化剂具有与20%(w/w)的商业Pt/C催化剂相媲美的ORR活性,其半波电位仅比Pt/C催化剂低31 mV。随着硫化时间的增加,硫化钴颗粒逐渐增大,催化剂中碳材料的无序程度出现先减小后增大的趋势。在硫化时间为10 min时,复合催化剂在0.1 mol·L-1KOH中表现出良好的电催化活性,且在ORR过程中复合催化剂的平均转移电子数可达到3.72,接近于4,说明氧气在该催化剂表面发生的是四电子转移过程。     

碘化四-(4-三甲胺苯基)卟啉钴配合物的合成和性质研究

合成了一种新的水溶性碘化四-(4-三甲胺苯基)卟啉钴(CoTAPP·I·6H₂O)的配合物,进行了元素分析和差热,热重分析、测定了它的可见、紫外光谱、红外光谱、激光拉曼光谱和ESR谱,并对合成条件和性质进行了一些探讨。     

基于卟啉衍生物红光材料的合成及物性研究

利用Schiff base反应合成了两个卟啉衍生物TPP-AQ, TPP-PD. 通过循环伏安、紫外可见吸收光谱、荧光光谱及理论计算等对其物性进行了研究. 结果显示: TPP-AQ, TPP-PD氧化电位分别为E_1/2＝1.07, 1.30 V和1.21, 1.36 V, 与TPP-PD相比, TPP-AQ的两个氧化还原电位都发生了负移|TPP-AQ与TPP-PD的最大紫外可见吸收峰分别在441和431 nm, TPP-AQ的吸收波长较TPP-PD有一定程度的红移, 通过理论计算可知这是由于TPP-AQ共轭程度优于TPP-PD导致的. TPP-AQ和TPP-PD的荧光主发射峰分别在657和656 nm, 半峰宽分别为30和27 nm, 有较好的红光色纯度.     

Metal-Carbon Composites Based on Carbonized Melamine-Formaldehyde Polymer and Their Electrocatalytic Properties

Russian Journal of Electrochemistry - Metal/N-doped carbon (M/C–N) composites were prepared using the melamine-formaldehyde polymer (MFP) as a source of C–N carbon and a metal salt...     

Electrocatalytic Oxidation of Sulfite on a Cobalt Pentacyanonitrosylferrate Film Modified Glassy Carbon Electrode

The electrocatalytic oxidation of sulfite has been studied on the cobalt pentacyanonitrosylferrate modified glassy carbon electrode (CoPCNF). The CoPCNF films on the glassy carbon electrodes show an excellent electrocatalytic activity toward the oxidation of sulfite in 0.5 M KNO₃. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry, rotating disk electrode (RDE) voltammetry and chronoamperometry. The average value of the rate constant, K, for the catalytic reaction and the diffusion coefficient, D, were evaluated by different approaches for sulfite and found to be 2.9×10² M^?1s^?1 and 4.6×10^?6 cm²s^?1, respectively. At a fixed potential under hydrodynamic conditions (stirred solutions), the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 5×10^?6–1×10^?4 M. The detection limit of the method is 3×10^?6 M., low enough for the trace sulfite determination.