气相色谱法测定食品包装材料中微量甲醛

建立了食品包装材料中微量甲醛的气相色谱检测方法.样品浸泡液经2,4-二硝基苯肼(DNPH)衍生,正己烷萃取衍生反应物后,气相色谱-电子捕获检测器法测定.采用乙腈多次重结晶法提纯衍生剂(DNPH),以降低DNPH中含有的甲醛衍生产物,避免影响测定;探讨了衍生化反应的条件以及色谱条件.甲醛的残留在0.05～50 mg/L的范围内线性关系良好,检出限为0.05 mg/kg,相对标准偏差为2.7%～5.0%,回收率范围在88.6%～98.0%之间.     

分散液液微萃取-高效液相色谱串联质谱法快速测定水迁移相中甲醛

建立了分散液液微萃取-高效液相色谱串联质谱法快速测定轻纺消费品水迁移相中痕量甲醛的分析方法。水迁移相甲醛首先与2,4-二硝基苯肼(2,4-DNPH)衍生化反应生成甲醛-2,4-二硝基苯腙,优化的反应时间为15 min,2,4-DNPH浓度为5 mmol/L,HCl浓度为50 mmol/L;在分散液液微萃取过程中,以500μL乙腈为分散剂、50μL四氯乙烯为萃取剂瞬间完成衍生物的萃取富集后,进行HPLC-ESI-MS/MS分析,分析时间为3.5 min。水相中甲醛的检测线性范围为0.001~1 mg/L,线性相关系数(R2)为0.9987,检出限为0.25μg/L。平均加标回收率范围在82.8%~113.5%,相对标准偏差范围在2.1%~9.2%,平均富集倍数为120。方法已经应用于轻纺消费品水迁移相中甲醛含量的测定。     

柱前衍生-高效液相色谱法测定蔬菜中甲醛含量

建立了蔬菜中甲醛含量的高效液相色谱分析方法。样品用水提取、2,4-二硝基苯肼衍生及二氯甲烷萃取、浓缩后,采用Waters Sunfire C18色谱柱(250×4.6 mm,5μm)分离,流动相为乙腈-水(1∶1,V/V),在355nm波长处紫外检测。甲醛在0.1~2.0μg/mL浓度范围内呈线性关系,相关系数0.9989,方法检出限为1.0 mg/kg,在2~10mg/kg添加浓度范围内,甲醛平均回收率为78.1%~114.2%,相对标准偏差在0.8%~9.5%之间。     

柱前衍生-萃取阻断反应-高效液相色谱法测定化妆品中游离甲醛

建立了柱前衍生化-萃取阻断反应-高效液相色谱(HPLC)测定化妆品中甲醛的方法。化妆品中甲醛检测的难点是: 甲醛缓释剂类防腐剂在衍生过程中释放甲醛,影响游离甲醛的准确测定。以2,4-二硝基苯肼(DNPH)乙腈溶液-磷酸盐缓冲液(pH 2)(1:1, v/v)为提取溶液,于室温下快速衍生2 min后,立即加入二氯甲烷萃取,阻断衍生反应,经乙腈稀释后进行HPLC测定。以Agilent C18柱(250 mm×4.6 mm, 5 μm)为分离柱,乙腈-水(60:40, v/v)为流动相,流速为1.0 mL/min,于355 nm波长下检测。在洗发水、乳液、膏霜、洗手液、牙膏、指甲油、粉饼中分别添加50、100、500、1000 μg/g 4个浓度水平的甲醛,其回收率为81%～106%,相对标准偏差(n=6)＜5.0%。方法的定量限(以信噪比(S/N)＞10计)为50 μg/g。该方法快速、简便、重现性好,且可以有效避免甲醛缓释剂类防腐剂分解释放甲醛,适用于化妆品中游离甲醛的测定。     

小麦粉中甲醛(吊白块)的测定方法研究

对小麦粉中甲醛提取方法、甲醛与2,4-二硝基苯肼的衍生化反应条件以及甲醛衍生物的提取净化方法进行了研究, 建立了一种小麦粉中甲醛(吊白块)的高压液相色谱测定方法.该方法在甲醛浓度为0.026～0.832 μg/mL范围内与其衍生物的色谱峰面积呈显著线性相关, 相关系数r=0.9986. 小麦粉中甲醛不同添加量的平均回收率＞99%;吊白块不同添加量的平均回收率＞94%(以甲醛量计). 重复测定相对标准偏差平均为4.5%, 甲醛的检出限为9.6 μg/L, 相当于小麦粉中甲醛的最小检出量为0.24 mg/kg.     

衍生-气相色谱法测定水产品中的游离甲醛

建立了水产品中游离甲醛残留量的衍生-气相色谱快速检测方法,对衍生剂、抗干扰剂、萃取剂、色谱条件进行了研究.用HP-5 (30 m×0.32 mm i.d.,0.25 μm)毛细管色谱柱,程序升温,γ-ECD检测器,外标法定量.甲醛的检出限为0.05 mg/kg,在0.1～20.0 mg/L范围内,其线性相关系数R2=0.9994,标准偏差为0.041,在0.5、 1.5、 5.0 mg/kg 3个添加水平下回收率为89.6%～102.6%.3个实验室间的RSD为2.7%～4.4%.     

高效液相色谱法测定卷烟爆珠中的甲醛与乙醛

基于自主设计的一种新型的集萃取、过滤和转移功能为一体的样品萃取管,建立了高效液相色谱(HPLC)测定卷烟爆珠中甲醛和乙醛的分析方法。爆珠用乙腈水溶液萃取,在酸性条件下,经2,4-二硝基苯肼衍生化后,衍生物直接用HPLC法测定。结果表明:采用改进的样品萃取管可大大简化前处理步骤,甲醛和乙醛分别在8~1 500μg/L与10~1 650μg/L范围内呈较好的线性关系,相关系数(r~2)大于0.999,检出限分别为2.5、2.8μg/L,定量下限分别为8.0、9.5μg/L;在2.0、5.0、10.0μg/g 3个加标水平下的平均回收率为96.9%~101.1%,日内精密度和日间精密度均小于4%。该方法具有较好的重复性,适用于卷烟爆珠中甲醛和乙醛的测定。     

顶空固相微萃取-气相色谱法测定生活饮用水中痕量1,4-二氧六环

建立了生活饮用水中痕量1,4-二氧六环的顶空固相微萃取(HS/SPME)-气相色谱测定方法。考察并优化了萃取头、萃取温度、萃取时间、pH值、样品量、色谱条件等参数。结果表明:提取效率较好的方法是3 mL水样中加入3 mL 600 g/L氢氧化钠溶液,用85 μm Carboxen-PDMS萃取头萃取,用键合碱改性的大口径、厚液膜PTA-5毛细管色谱柱测定。1,4-二氧六环在0.50~50.0 μg/L范围内线性关系良好,相关系数为0.9995;方法检出限(以S/N>3计)为0.14 μg/L;相对标准偏差为2.1%~4.5% (n=6);对实际样品中进行线性范围内的高、中、低3个加标水平的测定,回收率为95.5%~107%,相对标准偏差为1.1%~5.3% (n=6)。建立的方法简便、准确、重现性好、灵敏度高,适合生活饮用水中痕量1,4-二氧六环的常规监测。     

负载型混晶纳米TiO_2/硅藻土复合材料的制备及其光催化性能

选用市售硅藻土作为载体,采用液相沉积法制备了负载型混晶纳米TiO2/硅藻土复合材料;采用扫描电镜、X射线衍射仪及红外光谱仪分析了复合材料的表面形貌和晶体结构;基于甲醛光催化降解实验考察了不同组成的负载型TiO2/硅藻土复合材料的光催化性能.结果表明,TiO2负载量为33.3%(TiO2与硅藻土的质量比为1∶2)的复合材料对甲醛光催化降解具有最佳催化活性.     

顶空-气相色谱质谱法快速测定水性涂料及胶粘剂中游离甲醛含量

建立了顶空-气相色谱质谱法快速测定水性涂料及胶粘剂中游离甲醛含量。样品经水溶解后置于顶空进样仪中,在80℃下加热20 min,使甲醛在气液两相间达到平衡,取顶空气体进气相色谱仪并以质谱检测器选择离子模式检测。以PLOT/Q毛细管柱实现甲醛与空气及其它干扰物的色谱分离,以保留时间及碎片离子相对丰度比定性,外标法定量。结果表明,甲醛浓度在1.0~100.0 mg/L范围内,线性方程为y=448.9777x+16.6253,相关系数为r=0.9997;方法检出限为5mg/kg;平均回收率为91.3%~96.7%;相对标准偏差(n=6)为1.3%~2.1%。本法可用于水性涂料、胶黏剂中游离甲醛含量的快速分析。     

Synthesis and application of molecularly imprinted polymer on selective solid-phase extraction for the determination of monosulfuron residue in soil

A novel sample clean-up procedure using molecularly imprinted polymer as the solid-phase extraction material for the determination of monosulfuron residue in soil samples has been developed. The molecularly imprinted polymer (MIP) was synthesized by non-covalent method with monosulfuron as the template. The selectivity and affinity of the MIP was evaluated by equilibrium adsorption and HPLC experiments, which demonstrated that the MIP has specific affinity for the template. The template-MIP interaction was studied by investigating the influence of different mobile phases on the retention of the template, which provided basic knowledge for the selection of the washing and elution solutions in the molecularly imprinted solid-phase extraction (MISPE) process. The study indicated that polar organic solvents with hydrogen bonding abilities have stronger eluting strength for the monosulfuron. After the MISPE procedure, a clean baseline was obtained in the HPLC quantification analysis. The recoveries of the method using the combination of MISPE and HPLC were above 93% and the R.S.D. was less than 3.2% in the soil sample determinations. Low detection limit (0.08 microg g(-1), when defined as 3 times of the noise) was also obtained in the method evaluation study.     

Determination of formaldehyde in beverages using microwave-assisted derivatization and ionic liquid-based dispersive liquid-liquid microextraction followed by high-performance liquid chromatography

A simple method based on simultaneous microwave-assisted derivatization and ionic liquid-based dispersive liquid-liquid microextraction (IL-based DLLME) is proposed for the derivatization, extraction and preconcentration of formaldehyde in beverage samples prior to the determination by high-performance liquid chromatography (HPLC). Formaldehyde was in situ derivatized with 2,4-dinitrophenylhydrazine (DNPH) and simultaneously extracted and preconcentrated by using microwave-assisted derivatization and IL-based DLLME in a single step. Several experimental parameters, including type and volume of extraction solvent, type and volume of disperser, microwave power and irradiation time, volume of DNPH, pH of sample solution, and ionic strength were evaluated. When the microwave power was 120 W, formaldehyde could be derivatized and extracted simultaneously only within 90 s. Under optimal experimental conditions, good linearity was observed in the range of 0.5-50 ng/mL with the correlation coefficient of 0.9965, and the limit of detection was 0.12 ng/mL. The proposed method was applied to the analysis of different beverage samples, and the recoveries of formaldehyde obtained were in the range of 84.9-95.1% with the relative standard deviations lower than 8.4%. The results showed that the proposed method was a rapid, convenient and feasible method for the determination of formaldehyde in beverage samples.     

聚合物整体柱微萃取-高效液相色谱法检测鸡蛋中的磺胺嘧啶和磺胺二甲嘧啶残留

建立了鸡蛋中磺胺嘧啶和磺胺二甲嘧啶残留量的聚合物整体柱微萃取和高效液相色谱检测方法。以聚(甲基丙烯酸-乙二醇二甲基丙烯酸酯)毛细管整体柱作为萃取装置。为了得到较高的萃取效率,优化了影响萃取效率的参数(萃取流速、萃取体积、样品基质pH值)。样品经过匀浆、乙醇提取、磷酸盐缓冲溶液稀释、离心等步骤后直接进行萃取。鸡蛋中磺胺嘧啶和磺胺二甲嘧啶的检出限分别为11.2 ng/g和8.8 ng/g,在50～5000 ng/g的浓度范围内具有良好的线性关系。加标回收率大于65%,日内、日间测定的相对标准偏差不高于8.2%。结果表明,方法简单、快速、灵敏度高,适用于鸡蛋中磺胺嘧啶和磺胺二甲嘧啶的常规分析。     

Determination of formaldehyde in shiitake mushroom by ionic liquid-based liquid-phase microextraction coupled with liquid chromatography

Using ionic liquid as extraction solvent and 2,4-dinitrophenylhydrazine (DNPH) as derivative agent, formaldehyde in shiitake mushroom was determined by liquid-phase microextraction coupled with high-performance liquid chromatography (HPLC). Shiitake mushroom was leached with water and filtrated, then the formaldehyde in filtrate was derivatized with DNPH and extracted simultaneously into a 10 μl drop of ionic liquid suspended on the tip of the microsyringe, and finally injected into the HPLC system for determination. The proposed procedure has a detection limit of 5 μg l⁻¹ formaldehyde in extraction solution, thus the mushroom sample filtrate could be diluted with a large ratio to eliminate the influence of sample matrix. The method has a relative standard deviation of 3.5% between days for 53.5 μg l⁻¹ formaldehyde standards. High contents of formaldehyde (119-494 μg g⁻¹ wet weight), which is harmful for human beings, were detected in shiitake mushroom. Therefore, strategies must be taken to prevent the accumulation and strictly control the content of formaldehyde in shiitake mushroom.     

Extraction and preconcentration of formaldehyde in water by polypyrrole‐coated magnetic nanoparticles and determination by high‐performance liquid chromatography

In this study, a simple and rapid extraction method based on the application of polypyrrole‐coated Fe₃O₄ nanoparticles as a magnetic solid‐phase extraction sorbent was successfully developed for the extraction and preconcentration of trace amounts of formaldehyde after derivatization with 2,4‐dinitrophenylhydrazine. The analyses were performed by high‐performance liquid chromatography followed by UV detection. Several variables affecting the extraction efficiency of the formaldehyde, i.e., sample pH, amount of sorbent, salt concentration, extraction time and desorption conditions were investigated and optimized. The best working conditions were as follows: sample pH, 5; amount of sorbent, 40 mg; NaCl concentration, 20% w/v; sample volume, 20 mL; extraction time, 12 min; and 100 μL of methanol for desorption of the formaldehyde within 3 min. Under the optimal conditions, the performance of the proposed method was studied in terms of linear dynamic range (10–500 μg/L), correlation coefficient (R² ≥ 0.998), precision (RSD% ≤ 5.5) and limit of detection (4 μg/L). Finally, the developed method was successfully applied for extraction and determination of formaldehyde in tap, rain and tomato water samples, and satisfactory results were obtained.     

Extraction of clenbuterol from urine using hydroxylated poly(glycidyl methacrylate-co-ethylene dimethacrylate) monolith microextraction followed by high-performance liquid chromatography determination

A hydroxylated poly(glycidyl methacrylate-co-ethylene dimethacrylate) (GMA-co-EDMA) monolithic capillary was prepared for polymer monolith microextraction (PMME). Coupled to HPLC with UV detection, this extraction medium was successfully applied to establish a simple and fast method for the analysis of clenbuterol (CLB) in urine. To obtain optimum extraction performance, the effects of pH value and ionic strength of the sample matrix on extraction efficiency were investigated. The linearity of the method was evaluated over a concentration range of 10-2000 ng/mL and the correlation coefficient (R2 value) was 0.9985. The detection limit and quantification limit were 2.3 and 7.7 ng/mL, respectively. Good reproducibility of the method was obtained, yielding the intra- and interday RSDs less than 5.1 and 9.1%, respectively. Moreover, the hydroxylated poly(GMA-co-EDMA) monolithic capillary exhibited good preparation reproducibility and long-term extraction life. When applied to the determination of CLB in urine samples, an effective removal of interfering compounds was achieved and recoveries were in the range of 87.6-106%. The determination of CLB from one real sample including pretreatment, extraction, and analysis could be finished within 30 min.     

Preparation and Chelating Properties of 4-Bromosalicylic Acid-Formaldehyde Polymers. Part II

4-Bromosalicylic acid (BS) was condensed with various proportions of formaldehyde using different acid catalysts. The polymer samples have been characterized by IR spectral studies, by their number-average molecular weight (M _n), and by TGA. Viscosity measurements of selected polymer samples in DMF showed that their solutions exhibited polyelectrolyte behavior. The intrinsic viscosity [η] of the polymer samples were measured in 80:20 (v/v) DMF/water containing 1% KBr, a medium in which the polymers exhibited normal behavior. Metal chelates of one polymer sample are characterized. Ion-exchanging properties of the same sample are studied by application of the batch equilibrium method     

Determination of enrofloxacin and ciprofloxacin in milk using molecularly imprinted solid-phase extraction

A molecularly imprinted solid-phase extraction procedure was developed for the simultaneous identification of enrofloxacin and its active metabolite, ciprofloxacin, in milk samples. Water-compatible molecularly imprinted polymers synthesized in a water-methanol system show a high degree of cross-reactivity for enrofloxacin and ciprofloxacin in aqueous environments. The imprinted particles were applied as selective sorbents in a solid-phase extraction process focusing upon complex milk matrices, which allowed the matrix compounds present in milk samples to be removed effectively. The extracts were sufficiently clean for further chromatographic analysis, and no interference originating from the biological matrix was observed. The mean recoveries of enrofloxacin and ciprofloxacin from milk sample were 82.6-93.5% and 81.2-94.8%, respectively, with the RSD less than 7.5%. This method is simple and sensitive, and is therefore an alternative tool to the existing HPLC methods for analyzing residual enrofloxacin and ciprofloxacin in biological samples.     

Sponge-nested polymer monoliths: Versatile materials for the solid-phase extraction of bisphenols

Polymer monoliths are promising materials for sample preparation due to their high porosity, pH stability, and simple preparation. The use of melamine formaldehyde foams has been reported as an effective support to prepare highly robust silica and polymer monoliths. Herein, divinylbenzene monoliths based on a 50:50 (%, w/w) crosslinker/porogen ratio have been nested within a melamine-formaldehyde sponge, resulting in monoliths with a surface area higher than 400 m²/g. The extraction performance of these monoliths was evaluated for the extraction of endocrine-disrupting bisphenols from aqueous solutions. We evaluated for the first time the versatility of sponge-nested polymer monoliths by comparing three different extraction modes (vortex mixing, magnetic stirring, and orbital shaking). Vortex mixing showed a comparable recovery of bisphenols (39%–81%) in a shorter extraction time (30 min, instead of 2 h). In addition, the robustness of the sponge-nested polymer monoliths was demonstrated for the first time by reshaping a larger monolithic cube (0.125 cm³) into four smaller pieces (4 × 0.03125 cm³) leading to a 16%–21% increase in extraction efficiency. This effect was attributed to an increase in the effective contact area with the sample, obtaining a higher analyte extraction capacity.