Methyl orange degradation enhanced by hydrogen spillover onto platinum nanocatalyst surface

Following a thermal reduction method, platinum nanoparticles were synthesized and stabilized by polyvinylpyrrolidone. The colloidal platinum nanoparticles were stable for more than 3 months. The micrograph analysis unveiled that the colloidal platinum nanoparticles were well dispersed with an average size of 2.53 nm. The sol–gel‐based inverse micelle strategy was applied to synthesize mesoporous iron oxide material. The colloidal platinum nanoparticles were deposited on mesoporous iron oxide through the capillary inclusion method. The small‐angle X‐ray scattering analysis indicated that the dimension of platinum nanoparticles deposited on mesoporous iron oxide (Pt‐Fe₂O₃) was 2.64 nm. X‐ray photoelectron spectroscopy (XPS) data showed that the binding energy on Pt‐Fe₂O₃ surface decreased owing to mesoporous support–nanoparticle interaction. Both colloidal and deposited platinum nanocatalysts improved the degradation of methyl orange under reduction conditions. The activation energy on the deposited platinum nanocatalyst interface (2.66 kJ mol^?1) was significantly lowered compared with the one on the colloidal platinum nanocatalyst interface (40.63 ± 0.53 kJ mol^?1).     

Mechanism of the formation of photosensitive nanostructured TiO<Subscript>2</Subscript> with low content of CdS nanoparticles

A method for synthesizing a CdS/TiO₂ composite material, active in the visible region, was described. The CdS/TiO₂ composite was obtained by the sol–gel synthesis of nanostructured TiO₂ in a medium of a stable colloidal solution of CdS nanoparticles. The TiO₂ matrix produced by the sol–gel process is amorphous and contains a nanocrystalline anatase phase, the content of which depends on the Ti(OBu)₄ hydrolysis rate. The content of CdS nanoparticles forming in the colloidal solution and participating in the TiO₂ matrix sensitization is determined by the initial CdS: Ti(OBu)₄ ratio. Although the content of CdS nanoparticles in the composite is low (no more than 3 wt %), the composite demonstrates catalytic activity in the visible region, thus proving the possibility of reducing the content of toxic CdS nanoparticles in the TiO₂ matrix without decreasing the photosensitivity of the CdS/TiO₂ composite.     

Facile and ultra large scale synthesis of nearly monodispersed CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by a low temperature sol–gel route

Nearly monodispersed cobalt ferrite nanoparticles were synthesized by a low temperature sol–gel route using propylene oxide as a gelation agent. The nanoparticles were obtained by the reaction of FeCl₂ and CoCl₂ in ethanol solution with propylene oxide to form the sol, followed by the boiling of the sol solution. The unique chemistry of this procedure allows the formation of highly homogeneous gel intermediate, resulting in the great reducing of crystallization temperature of ferrites to less than 100 °C without postannealing step. This guarantees the preparation of well defined and non-aggregated ferrite nanoparticles on an ultra-large scale of about 75 g in a single reaction. This large scale synthesis strategy offers important advantages over other conventional routes for the preparation of CoFe₂O₄ nanoparticles, showing the promising application of this route in the industrial production.     

Synthesis of Macroporous PMMA/Silica Nanocomposite Monoliths in Supercritical Carbon Dioxide

Summary: Macroporous monoliths consisting of silica nanoparticles embedded in poly(methyl methacrylate) (PMMA) were synthesized in supercritical CO₂. Well‐dispersed silica particles, pretreated with functional 3‐(trimethoxysilyl)propyl methacrylate (MPS), were to form colloidal PMMA nanocomposites followed by a sol‐gel transition forming interconnected structures resulting in micron‐sized pores with specific areas between 1 and 7 m² · g⁻¹. SEM and TEM results revealed uniform morphological characteristics of the composite materials and good dispersions of the silica nanoparticles.

SEM micrograph of PMMA/Silica nanocomposites forming interconnected macroporous monolith. The average size of the silica particles is 50 nm.     

Synthesis of gold nanoparticles in sol–gel glass porogens containing [bmim][BF4] ionic liquid

The [bmim][BF₄] ionic liquid effect on gold nanoparticles formation in silica sol–gel materials is studied in order to produce gel-derived glasses with optical properties. The characteristic red color from gold nanoparticles is observed for transparent glass monoliths obtained sintering, between 365 and 425 °C, a silica sol–gel precursor containing HAuCl₄·3H₂O and [bmim][BF₄], under normal atmospheric conditions. The effect of sintering the ionogel at different temperatures (T_sint) or times (t_sint) on the optical properties, shape, size, and distribution of gold nanoparticles is discussed. Presence of the gold particles is observed using transmission electron microscopy images followed by energy dispersive X-ray spectroscopy analysis. The thermal decomposition of [bmim][BF₄] in the ionogel is investigate using calorimetric and spectroscopic techniques, and by analysis of volatile compounds released by the sol–gel material during sintering. With these results a mechanism for the formation of the gold nanoparticles is proposed, where a first ionic liquid degradation step provides the reductive environment that enables the gold nanoparticles production at the range of temperatures between 350 and 425 °C. Upon sintering the synthesized materials the ionic liquid acts as a sacrificial additive and the ionic liquid thermal decomposition products enables the formation of gold nanoparticles in the sol–gel matrix.     

Pure face-centered-cubic (fcc) and hexagonal-close-packed (hcp) nickel phases obtained in air atmosphere sol–gel process and fcc nickel phase obtained in N2 protected sol–gel process

Air atmosphere sol–gel process is often applied to prepare metallic oxide materials. Here we show that metallic nickel phase can also be obtained by citric acid (CA) based air atmosphere sol–gel process in appropriate procedure. Pure fcc or hcp phases of nickel can be obtained in air atmosphere by using CA, nickel (II) acetylacetone, organic solvents and organic surfactants such as oleylamine (OAM), hexadecylamine. However, only NiO can be prepared by aqueous CA based sol–gel process. Oleic acid and OAM can also be used in organic solution mediated sol–gel process to prepare nickel nanoparticles in N₂ atmosphere with pure fcc phase at appropriate calcination temperature when 1-hexyl alcohol has been used as solvent. Impurities, such as hcp Ni or Ni₃N phase, do not occur in this experimental condition. Our results provide a new and facile way in preparation of metallic nanoparticles.     

Low temperature and size controlled synthesis of monodispersed γ-Fe<Subscript>2</Subscript>O<Subscript>3 </Subscript>nanoparticles by an epoxide assisted sol–gel route

Monodispersed γ-Fe₂O₃ nanoparticles were prepared by a procedure-simple and precursor-cheap route, epoxide assisted sol–gel method. The γ-Fe₂O₃ nanoparticles were obtained by the reaction of FeCl₂ in ethanol solution with propylene oxide to form the sol, following by the boiling of the solution. As compared with other metal ions of +2 formal charge, the unexpected acidity of FeCl₂ in ethanol solution assure the formation of sol. As an advantage, the unique chemistry of this route results in the low temperature of synthesis, leading to the extremely small particle size of 2.3 nm and non-aggregation state of the particles.     

Synthesis of silica–titania composite oxide via “green” aqueous peroxo-route

The preparation procedure of silica–titania composite oxide using novel solution/sol single precursor containing titanium peroxocomplex and silicic acid has been described. Pechini-type sol–gel process has been used to prepare oxides from the aqueous precursor. Some structural, morphological and textural characteristics of the prepared material have been presented. Composite SiO₂/TiO₂ has high surface area (c.a. 300 m²/g), and it is composed of anatase nanoparticles with the mean diameter of 5 nm embedded in amorphous silica, then TiO₂ prepared via similar method is presented as a mixture of anatase and rutile phases. The proposed synthetic procedure meets the requirements of “green chemistry”.     

Sol–gel process of carbon-supported nickel nanoparticles using different solvents and protecting atmospheres

Carbon-supported nickel nanoparticles have been prepared by a sol–gel process under N₂ or H₂ atmospheres using different solvents such as distilled water, ethanol, acetone and 1-propanol. In the aqueous sol–gel process, nickel nanoparticles with pure face-centered-cubic (fcc) phase can be obtained under N₂ atmosphere by using nickel nitrate, tartaric acid and sodium dodecyl sulfonate. When organic solvents are applied, nickel (Π) acetylacetone is required in order to obtain nickel nanoparticles with pure fcc phase under N₂ atmosphere. When the protecting atmosphere is H₂, nickel nitrate can be used to obtain nickel particles with pure fcc phase. Nickel nanoparticles with grain sizes of 4–6 nm in diameter can be prepared by using nickel (Π) acetylacetone [Ni(acac)₂], citric acid and hexadecylamine with solvent being acetone. 1-propanol is also effective in the preparation of nickel nanoparticles in this sol–gel process. We suggest that this sol–gel may be used for other metallic nanocrystals.     

Deposition of silver nanoparticles into porous system of sol–gel silica monoliths and properties of silver/porous silica composites

Porous monolithic gels based on silica with pore size from 16 nm to 3–5 μm have been synthesized using sol–gel technology. Parameters of porous structure are determined by the components molar ratio in the reaction mixture. The reduction processes of silver ions by formamide in the synthesized porous gel were studied. It has been shown that at the initial stage of the reaction, silver particles with size up to 10 nm are formed in the absence of any stabilizers. The composites Ag/SiO₂ were synthesized by means of the threefold impregnation of porous monoliths using the solution of silver nitrate in the mixture of methanol and formamide. Their catalytic activity in the CO oxidation was studied. It was discovered that after activation in oxygen and hydrogen the samples display a low temperature activity, which depends on the number of Si–O-nonbridging oxygen groups on the surface of silica porous monoliths.     

Synthesis of monolithic zirconia with macroporous bicontinuous structure via epoxide-driven sol–gel process accompanied by phase separation

Monolithic macroporous zirconia was synthesized through a new method involving an epoxide-driven sol–gel method accompanied by a spontaneous phase separation. The sol–gel transition utilized inorganic salt ZrCl₄ as primary precursor and propylene oxide as matrix former through a ring-opening reaction. Phase separation was induced with poly-(ethylene oxide) (PEO) and its tendency was adjusted by incorporating Mg²⁺/Y³⁺ and N-methylformamide (NFA) in starting solution. The morphology of the dried gel changed from a solid nanoporous structure through a phase separated macroporous bicontinuous structure to aggregates particles when varying Mg²⁺ or Y³⁺, NFA and PEO composition. An appropriate choice of the starting composition, by which the phase separation and gelation occurred parallel, allows the fabrication of macroporous zirconia monoliths in large dimensions (Φ = 30 mm, h = 8 mm). The skeleton of the monolithic macroporous zirconia gels possess a BET surface area of 271.7 m²/g. Accordingly, the effect and mechanisms of Mg²⁺, Y³⁺ and NFA during gelation process were proposed in detail. Moreover, Mg²⁺ or Y³⁺ might also act as stabilizer to form the magnesia or yttria stabilized tetragonal or cubic zirconia after the samples were heat-treated at high temperature (800 °C).     

Size‐Tunable Highly Luminescent SiO2 Particles Impregnated with Number‐Adjusted CdTe Nanocrystals

Highly luminescent SiO₂ particles impregnated with CdTe nanocrystals (NCs) are prepared by a sol–gel procedure. Partial ligand exchange from thioglycolic acid to 3‐mercaptopropyltrimethoxysilane (MPS) on the NCs enables retention of the initial photoluminescence (PL) efficiency of the NCs in water, while the simultaneous addition of a poor solvent (ethanol) results in regulated assembly of the NCs through condensation of hydrolyzed MPS. The SiO₂ particles thus prepared have, for example, a diameter of 16 nm and contain three NCs each. The PL efficiency of these particles is 40 %, while the initial efficiency is 46 % in a colloidal solution. The redshift and narrowed spectral width in PL observed after impregnation indicate that the concentration of NCs in these nearly reaches the ultimate value (on the order of 10²¹ particles per liter). The porosity of these particles is investigated by means of N₂ adsorption–desorption isotherms. Due to the SiO₂ shell, these particles have higher stability in phosphate‐buffered saline buffer solution than the initial NCs. Their potential use for labeling in bio‐applications is investigated by conjugating biotinylated immunoglobulin G to them by using streptavidin maleimide as linker. Successful conjugation is confirmed by electrophoresis in agarose gel. This preparation method is an important step towards fabricating intensely emitting biocompatible SiO₂ particles impregnated with semiconductor NCs.     

ZnO nanoparticles and poly(acrylic) acid-based polymer gel electrolyte for photo electrochemical cell

This work presents a photo electrochemical cell based on zinc oxide (ZnO) nanoparticles and poly(acrylic) acid (PAA) doped with sodium iodide (NaI) and iodine (I₂) polymer gel electrolyte. The ZnO powders were synthesized by sol–gel storage and sol–gel centrifugation. The ZnO powder synthesized via sol–gel centrifugation showed the optimal structural properties, with largest crystallite sizes of 58 nm, average particles size between 20 and 80 nm and indirect band gap energy of 3.20 eV. The highest conductivity [(8.0 ± 0.1) × 10^?2 S cm^?1] was obtained for PAA + 0.8 M NaI + 0.02 M I₂. This sample achieved the lowest activation energy (0.029 eV) and electrochemical stability at 1.6 V. The ZnO powder synthesized via sol–gel centrifugation and PAA + 0.8 M NaI + 0.02 M I₂ was fabricated as a Cu–ZnO/PAA + 0.8 M NaI + 0.02 M I₂/C-ITO photo electrochemical cell.     

Precursor and Solvent Effects in the Nonhydrolytic Synthesis of Complex Oxide Nanoparticles for Bioimaging Applications by the Ether Elimination (Bradley) Reaction

Investigation of the solvent and alkoxide precursor effect on the nonhydrolytic sol–gel synthesis of oxide nanoparticles by means of an ether elimination (Bradley) reaction indicates that the best crystallinity of the resulting oxide particles is achieved on application of aprotic ketone solvents, such as acetophenone, and of smallest possible alkoxide groups. The size of the produced primary particles is always about 5 nm caused by intrinsic mechanisms of their formation. The produced particles, possessing the composition of natural highly insoluble minerals, are biocompatible. Optical characteristics of the perovskite complex oxide nanoparticles can easily be controlled through doping with rare earth cations; for example, by Eu³⁺. They can be targeted through surface modification by anchoring the directing biomolecules through a phosphate or phosphonate moiety. Testing of the distribution of Eu‐doped BaTiO₃ particles, modified with ethylphosphonic acid, demonstrates their facile uptake by the plants with active fluid transport, resulting finally in their enhanced concentration within the cell membranes.     

Lactic acid based sol–gel process of Ag nanoparticles and crystalline phase control of Ni particles in aqueous sol–gel process

Nickel and silver particles were prepared by using sol–gel auto-combustion method under N₂ atmosphere where lactic acid was applied as chelating agent. The synthesis of nickel particles was carried out at various pH conditions (2–7), resulting in the face-centered-cubic or hexagonal-close-packed crystalline nickel phase. The morphology and structure of synthesized nickel particles and silver nanoparticles were characterized by X-ray diffraction, transmission electron microscope, energy dispersive X-Ray spectroscopy and differential scanning calorimetry-thermogravimetric analysis. The results show that the spherical Ag nanoparticles with diameters in the range of 18–27 nm and narrow size distribution can be obtained by this sol–gel process.     

A Novel Method for Preparing Nano‐ and Microcomposite Al2O3‐ZrO2 Ceramic Coatings

Nano‐ and microcomposite Al₂O₃‐ZrO₂ coatings were deposited on various substrates in a sol‐gel ceramic paint by a supercentrifugal force and a gradual sintering process. Fine metal oxide powders were dispersed in a sol‐gel solution by superpower ball milling so as to form a uniform stable ceramic paint. High‐resolution microscopy (FE‐SEM) was used to characterize the coating, indicating that the coating is composed of composite particle clusters with an average diameter of ～1 µm. The clusters consisted of larger particles with an average diameter of ～0.5 µm in center and smaller particles of ～100 nm surrounding the larger ones. The coating was relatively dense and increasingly dense toward the substrate surface.     

Active Exsolved Metal–Oxide Interfaces in Porous Single-Crystalline Ceria Monoliths for Efficient and Durable CH4/CO2 Reforming

Dry reforming of CH₄/CO₂ provides an attractive route to convert greenhouse gas into syngas; however, the resistance to sintering and coking of catalyst remains a fundamental challenge at high operation temperatures. Here we create active and durable metal–oxide interfaces in porous single-crystalline (PSC) CeO₂ monoliths with in situ exsolved single-crystalline (SC) Ni particles and show efficient dry reforming of CH₄/CO₂ at temperatures as low as 450 °C. We show the excellent and durable performance with ≈20 % of CH₄ conversion and ≈30 % of CO₂ conversion even in a continuous operation of 240 hours. The well-defined active metal–oxide interfaces, created by exsolving SC Ni nanoparticles from PSC Ni_xCe_1?xO₂ to anchor them on PSC CeO₂ scaffolds, prevent nanoparticle sintering and enhance the coking resistance due to the stronger metal–support interactions. Our work would enable an industrially and economically viable path for carbon reclamation, and the technique of creating active and durable metal–oxide interfaces in PSC monoliths could lead to stable catalyst designs for many challenging reactions.     

A novel catalyst based on electrospun silver-doped silica fibers with ribbon morphology

Mesoporous silica nanofibers and Ag-doped composite nanoribbons were synthesized by a facile combination of an electrospinning technique and the sol–gel method. Tetraethyl orthosilicate, polyvinylpyrrolidone (PVP), triblock poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide), copolymer Pluronic P123, and silver nitrate (AgNO₃) were the components of sol for the production of Ag-doped hybrid silica ribbons. Heat removal of structure-directing agent P123 in the hybrid fibers at high temperatures resulted in a mesoporous morphology, and the degradation of PVP caused AgNO₃ to convert into silver in the form of nanoparticles. The size and content of the particles in the hybrid ribbons could be controlled by the concentration of AgNO₃ and thermal treatment conditions. Scanning electron microscopy, N₂ adsorption–desorption isotherm, transmission electron microscopy, X-ray diffraction, and UV–Vis spectroscopy were used to characterize the composite ribbons. The catalytic activity of the ribbons was evaluated by reduction of methylene blue dye and found to be better than in previous studies.     

Epoxide assisted sol-gel synthesis of rutile NixTi1-3xSb2xO2 solid solution nanoparticles

Rutile Ni _x Ti_1-3x Sb_2x O₂ solid solution nanoparticles were synthesized by a sol-gel route using propylene oxide as a gelation agent. Titanium oxide nanopowder and 12% TiCl₃ solution were used as the source for titanium to investigate the influence of the titanium precursors on the formation of the target materials. It was found that the nanoparticles prepared using 12% TiCl₃ solution showed a much lower phase formation temperature (700°C) as compared to those prepared from TiO₂ nanoparticles (1000°C). This lower phase formation temperature allowed a substantial reduction of the aggregation of the particles during calcination leading to the formation of nearly mono-dispersed nanoparticles of about 20 nm. The results of this work show that the epoxide assisted sol-gel method is capable to produce titanium-based ternary oxide solid solution nanoparticles, owing to the formation of a highly homogeneous precursor gel intermediate.     

Features of composites prepared by radical graft-polymerization of styrene to a hydrophilic macromer adsorbed on ultrafine colloidal particles

Polymer modifications of ultrafine monodispersed colloidal metal oxide particles, smaller than 80 nm in diameter, by the graft-polymerization of styrene to a hydrophilic macromer adsorbed on the surface were investigated. The polymerization in ethanolic silica and titania colloid solution, which had negatively larger ζ-potentials, ?30 and ?42 mV in neutral aqueous solution respectively, gave poly(styrene)–silica or titania composite, being of nonspherical shape. The modifications of colloidal particles, having lower surface energy, such as Al(OH)₃ and CeO₂–TiO₂–SiO₂ complex, led to the formation of spherical composites, ranging in size from 500 to 3000 nm, of scattered metal oxide or hydroxide particles.