Surface ATRP of hydrophilic monomers from ultrafine aqueous silica sols using anionic polyelectrolytic macroinitiators

A convenient two-step route was developed to prepare new anionic ATRP macroinitiators from near-monodisperse poly(2-hydroxyethyl methacrylate) precursors by partial esterification with 2-bromoisobutyryl bromide, followed by esterification of the remaining hydroxyl groups using excess 2-sulfobenzoic acid cyclic anhydride. These new macroinitiators can be electrostatically adsorbed onto ultrafine cationic Ludox CL silica sols; subsequent surface polymerization of various hydrophilic monomers in aqueous solution at room temperature afforded a range of polymer-grafted ultrafine silica sols. The resulting sterically stabilized particles were characterized by dynamic light scattering, transmission electron microscopy, aqueous electrophoresis, FTIR spectroscopy, and elemental microanalyses.     

Synthesis of biocompatible poly[2-(methacryloyloxy)ethyl phosphorylcholine]-coated magnetite nanoparticles

A well-defined, double-hydrophilic diblock copolymer comprising poly[2-(methacryloyloxy)ethyl phosphorylcholine]-block-(glycerol monomethacrylate) (PMPC30-PGMA30, where the numbers represent the average degrees of polymerization for each block) was evaluated for the synthesis of colloidally stable ultrafine magnetite sols. Sterically stabilized paramagnetic sols were prepared in aqueous solution by chemical coprecipitation of ferric and ferrous salts in the presence of this block copolymer. The PMPC30-PGMA30-stabilized magnetite sol had a mean transmission electron microscopy (TEM) diameter of 9.4 +/- 1.7 nm and a mean hydrodynamic diameter of 34 nm. This sol exhibited improved colloidal stability with respect to long-term storage and pH variation compared with magnetite sols prepared in the presence of alternative water-soluble homopolymers and diblock copolymers. Fourier transform infrared (FT-IR) spectroscopy, thermogravimetry, electron spectroscopy imaging (ESI), and zeta potential studies indicate that the PMPC30-PGMA30 diblock copolymer was adsorbed onto the surface of the sol via the PGMA30 block, with the PMPC30 chains acting as the stabilizing block. Such sterically stabilized sols are expected to be improved contrast agents for magnetic resonance imaging (MRI) applications.     

Synthesis and characterization of shell cross-linked micelles with hydroxy-functional coronas: a pragmatic alternative to dendrimers?

Shell cross-linked (SCL) micelles with hydroxy-functional coronas have been constructed in aqueous solution by exploiting the micellar self-assembly behavior of a new thermoresponsive ABC triblock copolymer. This copolymer was prepared via atom transfer radical polymerization in a convenient one-pot synthesis and comprised a thermoresponsive core-forming poly(propylene oxide) (PPO) block, a cross-linkable central poly(2-(dimethylamino)ethyl methacrylate) (DMA) block, and a hydroxy-functional outer block based on poly(glycerol monomethacrylate) (GMA). DMF GPC analysis confirmed a unimodal molecular weight distribution for the PPO-PDMA-PGMA triblock copolymer precursor, with an M(n) of 12 100 and a polydispersity of approximately 1.26. This copolymer dissolved molecularly in aqueous solution at 5 degrees C but formed micelles with hydroxy-functional coronas above a critical micelle temperature of around 12 degrees C, which corresponded closely to the cloud point of the PPO macroinitiator. Cross-linking of the DMA residues using 1,2-bis(2-iodoethoxy)ethane produced SCL micelles that remained intact at 5 degrees C, i.e., below the cloud point of the core-forming PPO block. Dynamic light scattering studies confirmed that the SCL micelle diameter could be varied depending on the temperature employed for cross-linking: smaller, more compact SCL micelles were formed at higher temperatures, as expected. Since cross-linking involved quaternization of the DMA residues, the SCL micelles acquired cationic surface charge as judged by aqueous electrophoresis studies. These cationic SCL micelles were adsorbed onto near-monodisperse anionic silica sols, which were used as a model colloidal substrate. Thermogravimetric analyses indicated a SCL micelle mass loading of 2.5-4.4%, depending on the silica sol diameter and the initial micelle concentration. Aqueous electrophoresis measurements confirmed that surface charge reversal occurred after adsorption of the SCL micelles, and scanning electron microscopy studies revealed a uniform coating of SCL micelles on the silica particles.     

Graft polymerization of vinyl monomers onto nanosized alumina particles

To enhance the interfacial interaction in alumina nanoparticles filled polymer composites, an effective surface modification method was developed by grafting polystyrene and polyacrylamide onto the particles. That is, the alumina surface was firstly treated with silane, followed by radical grafting polymerization in aqueous or non-aqueous systems. Results of infrared spectroscopy and dispersiveness in solvents demonstrated that the desired polymer chains have been covalently bonded to the surface of the alumina particles. They also greatly changed their surface characteristics. In addition, effects of polymerization conditions, including ways of monomer feeding, concentrations of monomer and initiator, and reaction time, on the grafting reaction were presented. It was found that the growing polymer radicals and/or the grafted polymer chains had a blocking effect on the diffusion of radicals or monomers towards the surface of nanoalumina. This was due to the fact that the interaction between the solvent and the grafted polymers was weaker than that between the grafted polymers and the nanoparticles.     

Grafting of polyesters from carbon whisker surface: Copolymerization of epoxides with cyclic acid anhydrides initiated by COOK groups introduced onto the surface

To modify the surface of carbon whisker (vapor-grown carbon fiber) the grafting of polyesters by use of potassium carboxylate (COOK) groups introduced onto the surface was investigated. The introduction of COOK groups onto the carbon whisker was achieved by the treatment of surface carboxyl groups with KOH aqueous solution. Untreated carbon whisker has no ability to initiate the polymerization. It was found that the anionic ring-opening alternating copolymerization of epoxides with cyclic acid anhydrides is successfully initiated by COOK groups on the carbon whisker surface. The corresponding polyester was grafted onto the surface based on the propagation of polymer from COOK groups introduced on the surface. The percentage of grafting of the polyester from styrene oxide and phthalic anhydride was determined to be 91.0%. The polymerization rate and percentage of grafting increased upon addition of crown ether. Furthermore, the rate of polymerization increased with increasing the dielectric constant of the solvent, but the percentage of grafting decreased. Polyester-grafted carbon whisker was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1993 John Wiley & Sons, Inc.     

Photografting of vinyl polymers onto ultrafine inorganic particles: Photopolymerization of vinyl monomers initiated by AZO groups introduced onto these surfaces

The photografting of polymers onto ultrafine inorganic particles, such as silica and titanium oxide, initiated by azo groups introduced onto these surfaces was investigated. The introduction of azo groups onto the particles was achieved by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with surface isocyanate groups, which were introduced by the treatment with tolylene 2,4-diisocyanate. It was found that the photopolymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and N-vinylcarbazole, is initiated by ultrafine particles having azo groups. The corresponding polymers were effectively grafted onto these surfaces through the propagation of the polymer from the surface radicals formed by the photodecomposition of the azo groups: e.g., the percentage of grafting of PMMA and polystyrene onto silica was reached to 112 and 176%, respectively. The percentage of grafting onto silica in the graft polymerization initiated by photodecomposition of surface azo groups was much larger than that initiated by thermal decomposition. Polymer-grafted ultrafine particles thus obtained gave a stable colloidal dispersion in good solvents for the grafted chain. © 1994 John Wiley & Sons, Inc.     

Cationic Grafting of Vinyl Polymers onto a Carbon Whisker,Initiated by Acylium Perchlorate Groups Introduced onto the Surface

Abstract

The cationic graft polymerization of vinyl monomers onto a carbon whisker, vapor-grown carbon fiber, initiated by acylium perchlorate groups introduced onto the surface, was investigated. The introduction of acylium perchlorate groups onto a carbon whisker was achieved by the treatment of a carbon whisker having acyl chloride groups, which were introduced by the reaction of surface carboxyl groups with thionyl chloride, with silver perchlorate in nitrobenzene. It was found that the cationic polymerization of vinyl monomers, such as styrene, indene, N-vinyl-2-pyrrolidone, and n-butyl vinyl ether, is initiated by acylium perchlorate groups on a carbon whisker. In the polymerization, the corresponding vinyl polymers were grafted onto a carbon-whisker surface based on the propagation of polymer from the surface: the percentage of grafting of polystyrene and polyindene reached 42.5 and 100.3%, respectively. The percentage of polystyrene grafting decreased with increasing polymerization temperature because of preferential chain transfer reactions at higher temperatures. Polymer-grafted carbon whisker gave a stable colloidal dispersion in a good solvent for grafted polymer.     

Protein adhesion on silicon-supported hyperbranched poly(ethylene glycol) and poly(allylamine) thin films

Hyperbranching poly(allylamine) (PAAm) and poly(ethylene glycol) (PEG) on silicon and its effect on protein adhesion was investigated. Hyperbranching involves sequential grafting of polymers on a surface with one of the components having multiple reactive sites. In this research, PAAm provided multiple amines for grafting PEG diacrylate. Current methodologies for generating PEG surfaces include PEG-silane monolayers or polymerized PEG networks. Hyperbranching combines the nanoscale thickness of monolayers with the surface coverage afforded by polymerization. A multistep approach was used to generate the silicon-supported hyperbranched polymers. The silicon wafer surface was initially modified with a vinyl silane followed by oxidation of the terminal vinyl group to present an acid function. Carbodiimide activation of the surface carboxyl group allowed for coupling to PAAm amines to form the first polymer layer. The polymers were hyperbranched by grafting alternating PEG and PAAm layers to the surface using Michael addition chemistry. The alternating polymers were grafted up to six total layers. The substrates remained hydrophilic after each modification. Static contact angles for PAAm (32-44 degrees) and PEG (33-37 degrees) were characteristic of the corresponding individual polymer (30-50 degrees for allylamine, 34-42 degrees for PEG). Roughness values varied from approximately 1 to 8 nm, but had no apparent affect on protein adhesion. Modifications terminating with a PEG layer reduced bovine serum albumin adhesion to the surface by approximately 80% as determined by ELISA and radiolabel binding studies. The hyperbranched PAAm and PEG surfaces described in this paper are nanometer-scale, multilayer films capable of reducing protein adhesion.     

TFC polyamide membranes modified by grafting of hydrophilic polymers: an FT-IR/AFM/TEM study

Surface modification using grafting of a hydrophilic polymer onto the membrane surface is a possible route to improving the fouling properties of polyamide thin-film composite membranes. The structure of nanofiltration (NF) and reverse osmosis (RO) membranes modified using graft polymerization of acrylic (AA) monomers was visualized and analyzed using attenuated total reflection–Fourier transform infrared spectroscopy, atomic force microscopy and transmission electron microscopy. The results show that a layer of AA polymer is indeed formed on the polyamide surface, which could be accompanied by a change of the surface morphology. It was observed that for the NF membranes studied polymerization could also take place inside the pores of the support as a result of penetration of the monomer through the active layer, particularly for high degrees of grafting. It suggests that the modification procedures should be optimized so that the latter effect is minimized.     

Bi-continuous macroporous polymer derived from oligo-ethylene oxide di-vinyl ether by a cationic polymerization

We have newly developed a bi-continuous macroporous polymer derived from oligo-ethylene oxide di-vinyl ether by cationic polymerization. Although vinyl ether is not easily polymerized using radical polymerization in its homo-polymerization, we have found that a cationic polymerization with a combination of good and poor solvents for the glowing polymer chain realized bi-continuous macroporous polymer as the first example of cross-linked, macroporous vinyl ether polymer.     

氨基甲酸酯乙烯基醚类化合物光聚合性能研究

本文合成了一种双官能度的氨基甲酸酯乙烯基醚和一种三官能度的氨基甲酸酯乙烯基醚,并用实时傅立叶红外光谱分别监测了单官能度、双官能度和三官能度的乙烯基醚化合物在三芳基六氟锑酸锍鎓盐阳离子光引发剂(PAG-201)引发下的光聚合情况,对其光聚合动力学性能进行了比较,研究了引发剂PAG-201的浓度对双官能度单体光聚合的影响.结果表明,随着官能度的增加,乙烯基醚化合物的转化率和聚合速率降低.此外,对它们的聚合产物进行的热失重分析表明,随着官能度的增加,聚合产物的热稳定性增加.本文的结果对于研究开发基于氨基甲酸酯乙烯基醚单体的阳离子聚合体系具有较好的指导意义.     

Functionalization of Graphene Sheets via Chemically Grafting of PMMA Chains Through in-situ Polymerization

In this work, we report the preparation of graphene nanoplatelet which covalently functionalized with PMMA chains by introduction of vinyl groups onto graphene surface through simple esterification reaction between hydroxyl groups of graphite oxide and methacrylic anhydride. The synthesis is followed by in-situ polymerization with MMA monomers. The structural properties were characterized with X-ray diffraction spectroscopy (XRD) and scanning electronic microscopy (SEM) that showed the crystalline graphite is converted to individual layers during the synthesis steps. The grafting of PMMA chains was monitored with IR spectroscopy (FT-IR) and thermogravimetric analysis (TGA). The TGA results revealed 40% wt of PMMA chains chemically grafted onto graphene surface. Significant increase in glass transition temperature (T_g) and existence of polymer chains in two positions (physically absorbed and chemically grafting onto graphite surface) are indicated by differential scanning calorimetric (DSC) analysis.     

HA/PDM自组装复合胶体粒子及其乳化性能

以阴离子天然大分子透明质酸(HA)和阳离子单体甲基丙烯酸二甲氨基乙酯(DM)组成带相反电荷的聚合物/单体复合体系, DM通过水相原位聚合可制备荷正电的聚甲基丙烯酸二甲氨基乙酯(PDM), PDM与HA间的静电作用可诱导两者在水溶液中进行自组装, 得到HA/PDM复合胶体粒子. 用傅里叶变换红外(FTIR)光谱仪对HA/PDM复合物结构进行了表征. 用动态激光光散射(DLS)研究了HA与PDM复合体系在水溶液中的自组装行为, 并表征了反应时间对HA/PDM复合胶体粒子粒径的影响. 利用透射电镜(TEM)表征了胶体粒子的形貌. 考察了溶液pH 对胶体粒子粒径及zeta 电位的影响, 并对胶体粒子的乳化性能进行初步探索. 结果表明:DM单体聚合前, 无HA/DM复合物聚集体形成; 而随着DM的逐步聚合, HA与PDM可通过静电作用逐渐组装形成球状HA/PDM复合胶体粒子, 其粒径随反应时间延长逐渐减小并趋于稳定. 同时, 该复合胶体粒子具有pH敏感性和乳化性, 乳化性能较纯HA和PDM有较大提高.     

Polymer grafting via ATRP initiated from macroinitiator synthesized on surface

Macromolecular anchoring layer approach was used for preparation of an effective macroinitiator for the synthesis of grafted polymer layers by atom transfer radical polymerization (ATRP) initiated from the surface. For the initial surface modification, a thin layer of poly(glycidyl methacrylate) (PGMA) was deposited on the surface of a silicon wafer. The ATRP macroinitiator was synthesized on the substrate surface by the reaction between epoxy groups of PGMA and carboxy functionality of bromoacetic acid (BAA). Variation of the time and temperature of the BAA deposition as well as PGMA layer thickness allowed control over the amount of BAA attached to the surface. The PGMA anchoring layer allowed the achievement of initiator surface density significantly higher than that reported for a self-assembled monolayer of ATRP initiators. Polymer brushes were synthesized on the PGMA/BAA-modified substrates by ATRP. Different surface concentrations of BAA were used in our grafting experiments to acquire knowledge about the relationship between the amount of initiator anchored to the surface through PGMA and the rate of the grafted layer formation. The increase in the surface density of the initiating moieties led to the increase in the grafting rate. However, a cutoff initiator concentration beyond which no increase of the thickness of the grafted layer was observed. From comparison between the surface densities of the initiator and the attached polymer it was determined that the efficiency of the initiation from the surface was on the level of 5-15%.     

Photoinitiated cationic polymerization of epoxy alcohol monomers

A series of epoxy alcohols were prepared by simple, straightforward methods. These compounds were very reactive monomers that polymerized rapidly on UV irradiation in the presence of cationic photoinitiators. The kinetics of the cationic photopolymerization of these monomers were studied with diaryliodonium salt photoinitiators and real‐time IR spectroscopy. The rate of epoxide ring‐opening polymerization was enhanced markedly by the presence of the hydroxy group. Using model compounds, the monomers were shown to polymerize via an activated monomer mechanism. Simple epoxy alcohols polymerized to give polymers with a hyperbranched structure. The novel monomers also were observed to accelerate the rate of the photopolymerization of mono‐ and multifunctional epoxides. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 389–401, 2000     

Effective grafting of polymers onto ultrafine silica surface: Photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface and Mn2(CO)10

The effective grafting of vinyl polymers onto an ultrafine silica surface was successfully achieved by the photopolymerization of vinyl monomers initiated by the system consisting of trichloroacetyl groups on the surface with Mn₂(CO)₁₀ under UV irradiation at 25 °C. The introduction of trichloroacetyl groups onto the surface of silica was achieved by the reaction of trichloroacetyl isocyanate with surface amino groups, which were introduced by the treatment of silica with 3‐aminopropyltriethoxysilane. During the polymerization, the corresponding polymers were effectively grafted onto the surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mn₂(CO)₁₀. The percentage of poly(methyl methacrylate) grafting onto the silica reached 714.6% after 90 min. The grafting efficiency (proportion of grafted polymer to total polymer formed) in the polymerization of methyl methacrylate was very high, about 80%, indicating the depression of formation of ungrafted polymer. Polymer‐grafted silica gave a stable colloidal dispersion in good solvents for grafted polymer. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2157–2163, 2001     

Graft polymerization of vinyl monomers inside macroporous polyacrylamide gel,cryogel, in aqueous and aqueous‐organic media initiated by diperiodatocuprate(III) complexes

Graft polymerization initiated by diperiodatocuprate(III) complex (Cu(III)) initiator was found to be an effective and convenient method for graft polymerization of vinyl monomers onto macroporous polyacrylamide gels, the so‐called cryogels (pAAm‐cryogels). The effect of time, temperature, monomer and initiator concentration during the graft polymerization in aqueous and aqueous‐organic media was studied. The graft polymerization of water‐soluble monomers as [2‐(methacryloyloxy)ethyl]‐trimethylammonium chloride, 2‐hydroxyethyl methacrylate, N‐isopropylacrylamide, and N,N‐dimethylacrylamide proceeds with higher grafting yield in aqueous medium, as compared with that in aqueous‐organic media. Graft polymerization in aqueous‐organic media such as water–DMSO solutions allows grafting of water‐insoluble monomers such as glycidyl methacrylate and N‐tert‐butylacrylamide with high grafting degrees of 100 and 410%, respectively. It was found that the deposition of initiator on the pore surface of cryogels promoted graft polymerization by facilitating the formation of the redox couple Cu(III)‐acrylamide group. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1952–1963, 2006     

Peroxidase-catalyzed in situ polymerization of surface orientated caffeic acid

Nanoscale surface patterning and polymerization of caffeic acid on 4-aminothiophenol-functionalized gold surfaces has been demonstrated with dip pen nanolithography (DPN). The diphenolic moiety of caffeic acid can be polymerized by biocatalysis with laccase or horseradish peroxidase. In the present study, the DPN patterned features were polymerized in situ through the use of the peroxidase. Using samples prepared by DPN, microcontact printing, and adsorption on macroscopic substrates, the products were characterized by electrostatic force microscopy (EFM), MALDI-TOF, X-ray photoelectron spectroscopy (XPS), UV-vis, and FT-IR. The in situ surface polymerization resulted in the formation of a quinone structure, while the phenyl ester formed in bulk polymerization reactions was not detected. A different coupling site was observed when comparing the polymers obtained from solution (bulk) vs the surface DPN reactions. The structural differences were attributed to surface-induced pre-organization and orientation of the monomers prior to the enzymatic polymerization step. The results of this study expand the application of DPN technology to surface modification and surface chemistry reactions wherein stereo-regularity and regioselectivity can be exploited.     

Photoinduced graft polymerization of 2-methacryloyloxyethyl phosphorylcholine on polyethylene membrane surface for obtaining blood cell adhesion resistance

Phospholipid polymer, poly[2-methacryloyloxyethyl phosphorylcholine (MPC)], was grafted with polyethylene (PE) membrane using photoinduced polymerization technique to make the membrane resistant to cell adhesion. The water contact angle on the PE membrane grafted with poly(MPC) decreased with an increase in the photopolymerization time. This decrease corresponded to the increase in the amount of poly(MPC) grafted on the PE surface. The same graft polymerization procedure was applied using other hydrophilic monomers, such as acrylamide (AAm), N-vinylpyrrolidone (VPy) and methacryloyl poly(ethylene glycol) (MPEG). These monomers were also polymerized to form grafted chains on the PE membrane, and the grafting was confirmed with X-ray photoelectron spectroscopy. Analysis of amount and distribution of plasma proteins at the plasma-contacting surface of the original and the modified PE membranes were analyzed using immunogold assay. The grafting of poly(MPC) and poly(VPy) on PE membrane reduced the plasma protein adsorption significantly compared with that on the original PE membrane. However, the PE membranes grafted with poly(AAm) or poly(MPEG) did not show any effects on protein adsorption. Platelet adhesion on the original and modified PE membranes from platelet-rich plasma was also examined. A large number of platelets adhered and activated on the original PE membrane. Grafting with poly(AAm) did not suppress platelet adhesion, but grafting with poly(MPC) or poly(VPy) on the PE membrane was effective in preventing platelet adhesion. It is concluded that the introduction of the phosphorylcholine group on the surface could decrease the cell adhesion to substrate polymer.     

Polymerization of Vinyl Monomers on Mineral Surfaces; A Novel Method of Preparing Reinforcing Fillers

A novel method for producing modified mineral fillers is reported: The mineral surface is first made “acidic” and this acidic surface is used to initiate the cationic polymerization of vinyl or preferably divinyl monomers, the residual acidic sites being subsequently neutralized with ammonia or an organic base. During compounding, grafting occurs between the encapsulating polymer layer and the matrix polymer via previously formed peroxidic groups in this layer or via radical attachment at unsaturated centers in the polymer coating. The incorporation of these modified fillers in various grades of polyethylene results in significant improvements in processability and in tensile and impact strength relative to the properties of equivalent composites using untreated or merely hydrophobic fillers.