Chemiluminescence determination of atenolol in biological fluids by a europium-sensitized permanganate-sulfite system

A simple flow injection chemiluminescence (CL) method was developed for the determination of atenolol using Eu³⁺ as the probe. It was found that the weak CL generated by the KMnO₄-Na₂SO₃ reaction can be significantly enhanced by the atenolol-Eu³⁺ complex. The experimental conditions were optimized. The CL intensity was linearly related to atenolol concentration in the range from 8.0 × 10⁻⁹ to 1.0 × 10⁻⁵ g mL⁻¹. The detection limit (3s _b) was 3 × 10⁻⁹ g mL⁻¹ and the relative standard deviation for 1.0 × 10⁻⁷ g mL⁻¹ atenolol solution was 2.4% (n = 11). The method has high sensitivity, wide linear range, inexpensive instrumentation, and has been applied to the determination of atenolol in spiked human urine and plasma samples with recoveries within the range 95.5–104.0%. Supplementary material to this paper is available in electronic form at Electronic supplementary material: Discussion of the reaction mechanism and additional figures are available online as electronic supplementary material (ESM) at . Correspondence: Jianxiu Du, Key Laboratory of Analytical Chemistry for Life Science of Shaanxi Province, School of Chemistry and Materials Science, Shaanxi Normal University, Xi’an 710062, P.R. China     

Determination of Yttrium by Resonance Light Scattering Technique

 Yttrium was determined by means of the resonance light scattering (RLS) technique. The characteristics of resonance light scattering spectra of yttrium-1, 6-bi(1′-phenyl-3′-methyl-5′-pyrazolone-4′-) hexanedione (BPMPHD), the effective factors and optimum conditions were studied. In the pH range of 5.0–6.1, yttrium-BPMPHD complex produces three characteristic peaks of RLS at 365, 402 and 467 nm. The enhanced intensity of RLS is proportional to the concentration of yttrium in the range of 1.0×10⁻⁸ to 1.0×10⁻⁵ mol · L⁻¹. The limit of detection is 5.9×10⁻⁹ mol · L⁻¹. The method has been used for the determination of Y³⁺ in mixed rare earths. Correspondence: Key Lab for Colloid and Interface Chemistry of Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100, People’s Republic of China. e-mail: wux@sdu.edu.cn Received July 3, 2002; accepted October 20, 2002     

An electroanalytical study of the drug proflavine

A square wave adsorptive stripping voltammetric (SWAdSV) method was developed for the determination of proflavine. The electrochemical behaviour of proflavine was investigated by cyclic (CV) and square wave voltammetry (SWV) at the hanging mercury drop electrode (HMDE) and carbon paste electrode (CPE). Different parameters were tested to optimize the conditions of the determination. Better results were obtained by square wave voltammetry using CPE where two oxidation and a reduction peak, appeared, at 0.19, 0.94 and 0.20 V, respectively. The peak at 0.19 V is quasi-reversible and deposition dependent. Linearity was observed in the range of (0.2–23.4) × 10⁻⁸ M (r = 0.998) during the anodic scan and in the range of (1.17–117) × 10⁻⁸ M (r = 0.999) during the cathodic scan. The second peak at 0.94 V is irreversible and deposition independent. The linearity of this peak was observed in the range of (1.29–11.7) × 10⁻⁸ M (r = 0.998). The method was applied to the analysis of bovine serum and gave satisfactory results. Correspondence: S. Th. Girousi, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University, Thessaloniki 54124, Greece     

Ionic conduction of lithium for Perovskite-type compounds, Li x La(1− x )/3NbO3 and (Li0.25La0.25)1− x Sr0.5 x NbO3

Perovskite-type compounds, Li _x La_{(1− x )/3}NbO₃ and (Li_0.25La_0.25)_{1− x} Sr_{0.5 x} NbO₃ as lithium ionic conductors, were synthesized by a solid-state reaction. From powder X-ray diffraction, the solid solution ranges of the two compounds were determined to be 0≤x≤0.25 and 0≤x≤0.125, respectively. In the Li _x La_{(1− x )/3}NbO₃ system, the ionic conductivity of lithium at room temperature, σ₂₅, exhibited a maximum value of 4.7 × 10⁻⁵ S · cm⁻¹ at x = 0.10. However, because of the decrease in the lattice parameters with increasing Li concentration x˙, σ₂₅ of the samples decreased with increasing x from 0.10 to 0.25. Also, in the (Li_0.25La_0.25)_{1− x} Sr_{0.5 x} NbO₃ system, the lattice parameter increased with the increase of Sr concentration and the σ₂₅ achieved a maximum (7.3 × 10⁻⁵ S · cm⁻¹ at 25 °C) at x = 0.125. Received: 12 September 1997 / Accepted: 15 November 1997     

Concerning the Chiral Discrimination and Helix Inversion Barrier in Hypericinates and Hypericin Derivatives

 It was found that the hypericinate salts of (R)-1-phenylethylamine and (S)-1-(1-naphthyl)-ethylamine display a small chiroptical signal of the same sign only at high concentrations in an apolar solvent. No further indications of a chiral discrimination between the helical conformers of hypericinate could be found in these cases. However, upon esterification of the 3-hydroxyl group of hypericin with (1S)-camphanic chloride, the two diastereomers were found in an 1:1 ratio equilibrating rather fast at temperatures above 30°C with one diastereomer in excess. From the temperature dependence of the equilibrium positions (measured by means of CD and ¹H NMR), a ΔG ⁰ value of 5.8±0.5 kJ·mol⁻¹ was derived. Accordingly, the chiral discrimination of the (M)-configured enantiomer of the helix by the (S)-configured auxiliary occurred at an intermediate level. From the temperature dependence of the equilibration kinetics an activation energy of E _a = 70±0.5 kJ·mol⁻¹ was derived, which thus defines the upper limit of the helix inversion of hypericin and hypericinate. This value is by about 10 kJ·mol⁻¹ lower than the recently estimated limit.     

Determination of trace vanadium in soil by cloud point extraction and graphite furnace atomic absorption spectroscopy

This work describes a new analytical procedure for trace vanadium by graphite furnace atomic absorption spectroscopy coupled to cloud point extraction (CPE) as the separation-preconcentration method. The CPE behavior of vanadium using methylene blue as complex agent and Triton X-100 as a surfactant was investigated systematically. Under the optimized conditions, the detection limit was 0.7 ng · mL⁻¹, and the relative standard deviation was 4.3% for vanadium (c = 50.0 ng · mL⁻¹, n = 5). The recovery of vanadium was in the range of 98.9–102.8%. The method was applied to the analysis of vanadium in certified reference materials and real samples. The results obtained were in good agreement with the certified values. Correspondence: Xiashi Zhu, Key Laboratory of Environmental Material and Environmental Engineering of Jiangsu province/College of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002, P.R. China     

Concerning the Chiral Discrimination and Helix Inversion Barrier in Hypericinates and Hypericin Derivatives

Summary.  It was found that the hypericinate salts of (R)-1-phenylethylamine and (S)-1-(1-naphthyl)-ethylamine display a small chiroptical signal of the same sign only at high concentrations in an apolar solvent. No further indications of a chiral discrimination between the helical conformers of hypericinate could be found in these cases. However, upon esterification of the 3-hydroxyl group of hypericin with (1S)-camphanic chloride, the two diastereomers were found in an 1:1 ratio equilibrating rather fast at temperatures above 30°C with one diastereomer in excess. From the temperature dependence of the equilibrium positions (measured by means of CD and ¹H NMR), a ΔG ⁰ value of 5.8±0.5 kJ·mol⁻¹ was derived. Accordingly, the chiral discrimination of the (M)-configured enantiomer of the helix by the (S)-configured auxiliary occurred at an intermediate level. From the temperature dependence of the equilibration kinetics an activation energy of E _a = 70±0.5 kJ·mol⁻¹ was derived, which thus defines the upper limit of the helix inversion of hypericin and hypericinate. This value is by about 10 kJ·mol⁻¹ lower than the recently estimated limit. Corresponding author. E-mail: heinz.falk@jku.at Received March 22, 2002; accepted April 3, 2002     

Fluorimetric determination of traces of europium(III) using a new chelator and acetate or phosphate in dimethylsulfoxide as enhancers

A new Schiff-base ligand [N, N′, N″-Tri- (2,4-dihydroxyacetophenone) – triaminotriethylamine (TDATA)] with a tripodal structure was synthesized. Its fluorescence intensity with the europium(III) complex was increased about 178-fold in the presence of sodium acetate (NaAc) and about 126-fold in the presence of sodium phosphate (Na₃PO₄) solution. After adding the organic solvent dimethylsulfoxide (DMSO) to the above system, which leads to Eu³⁺ the fluorescence was further enhanced about 12-fold. Spectrofluorimetric determination of trace amounts of Eu³⁺ based on the phenomenon was performed. The excitation and emission wavelength is 365 nm and 615 nm, respectively. Under optimum conditions, the fluorescence intensities vary linearly with the concentration of Eu³⁺ in the range of 4.9 × 10⁻¹²–3.2 × 10⁻⁶ mol · L⁻¹ with a detection limit of 4.5 × 10⁻¹² mol · L⁻¹ (for the TDATA-NaAc-DMSO system) or 6.2 × 10⁻¹¹–8.6 × 10⁻⁶ mol · L⁻¹ with a detection limit of 6.0 × 10⁻¹¹ mol · L⁻¹ (for the TDATA-Na₃PO₄-DMSO system). Interferences of some rare earth metals and other inorganic ions are described. The method is a selective, sensitive, rapid and simple analytical procedure for the determination of europium(III) in a high purity yttrium oxide and synthetic sample. The mechanism for the fluorescence enhancement is also discussed.     

Ensemble of carbon fiber ultra-microelectrodes modified with nanotubes, and its application to the determination of dopamine

An ensemble of carbon fibers ultra-microelectrode modified with carbon nanotubes (EUME-CNTS) has been constructed based on a thin carbon nanotubes film which was coated onto surfaces of carbon fibers of ultra-microelectrode. SEM micrographs illustrated the image of carbon nanotubes on the carbon fiber surface. The electrochemical characteristics of the EUME-CNTS has been investigated by cyclic voltammetry. The electrochemical properties of dopamine on this electrode were also studied, and the detection limit was found to be 2.0 × 10⁻⁹ mol·L⁻¹. Linear calibration plots were obtained for the oxidation peak current in a range 1.0 × 10⁻⁷–8.0 × 10⁻⁵ mol·L⁻¹. Correspondence: Xiuhua Liu, Kuaizhi Liu, Department of Chemistry and Chemical Engineering, Henan University, Henan Kaifeng 475001, P.R. China     

Determination of Tannic Acid by Flow Injection Analysis with Inhibited Chemiluminescence Detection

A novel flow injection procedure has been developed for the determination of tannic acid based on the inhibition of the chemiluminescences in luminol-H₂O₂-Manganese tetrasulfonatophthalocyanine (MnTSPc) system by tannic acid. The method is simple, rapid and sensitive with a detection limit of 8 × 10⁻¹⁰ mol·L⁻¹ and a linear range of 7 × 10⁻⁹–5 × 10⁻⁶ mol·L⁻¹. The relative standard deviation is 1.9% for eleven measurements of 5 × 10⁻⁷ mol·L⁻¹ tannic acid. The method has been successfully applied to the determination of tannic acid in real Chinese gall and hop pellets samples.     

Kinetic-potentiometric assay of formaldehyde in pharmaceutical and industrial samples, monitored by copper solid ion selective electrode, after its reaction with the copper(II)-bis-(ethylenediamine) complex

A kinetic-potentiometric method is described for the quantitative assay of formaldehyde (HCHO) in pharmaceutical and industrial preparations. It is based on the reaction of HCHO with (ethylenediamine)-Cu(II)-sulfate [Cu(CH₂NH₂)₂(H₂O)₂] · SO₄. The changes in potential, resulting from the release of the Cu(II) cations, are monitored with a Cu(II)-ion selective electrode. The calibration curve for the HCHO is linear in the concentration range 50–250 mg L⁻¹, with a limit of detection of 8.5 mg L⁻¹. The method shows very good reproducibility with an RSD of 2.6% for successive injections (n = 5) of 150 mg L⁻¹ HCHO primary solution, while it is interference free. The method was successfully tested in various industrial and pharmaceutical preparations.     

Determination of rutin using a CeO2 nanoparticle-modified electrode

CeO₂ nanoparticles approximately 12 nm in size were synthesized and subsequently characterized by XRD, TEM and UV-vis spectroscopy. Then, a gold electrode modified with CeO₂ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified electrode demonstrated strong catalytic effects with high stability towards electrochemical oxidation of rutin. The anodic peak currents (measured by differential pulse voltammetry) increased linearly with the concentration of rutin in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁴ mol · L⁻¹. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol · L⁻¹. The relative standard deviation (RSD) of 8 successive scans was 3.7% for 5.0 × 10⁻⁶ mol · L⁻¹ rutin. The method showed excellent sensitivity and stability, and the determination of rutin in tablets was satisfactory.     

Microanalysis of Hydrogen, Boron and Fluorine in Vesuvianite by Means of SIMS, EPMA and FTIR

Vesuvianite, a complex sorosilicate, often contains variable (from trace-to-minor-element) amounts of H, B and F. We describe a microanalytical study of H, B and F in vesuvianite by means of Electron Probe Microanalysis (EPMA), Secondary Ion Mass Spectrometry (SIMS), and single-crystal Fourier-Transform InfraRed (FTIR) spectroscopy. Most crystals investigated are B- (up to 3.67 wt% B₂O₃) and F-rich (up to 2.38 wt%); H₂O ranges from 0.243 to 0.665 wt%. The H data obtained by SIMS allowed us to calibrate the quantitative analysis of H₂O by FTIR spectroscopy. The resulting molar absorption coefficient (ɛ _i = 100 000 ± 2000 L · mol⁻¹ · cm⁻²) is in excellent agreement with working curves available from the literature. Moreover, the SIMS data allowed us to obtain the calibration curve to estimate the B₂O₃ content on the basis on the FTIR absorbance: a _i = 34000 ± 1400 · B₂O₃ (wt%).     

Adsorptive anodic stripping voltammetry of zirconium(IV)-alizarin red S complex at a carbon paste electrode

A sensitive adsorptive anodic stripping procedure for the determination of trace zirconium at a carbon paste electrode (CPE) has been developed. The method is based on adsorptive accumulation of the Zr(IV)-alizarin red S(ARS) complex onto the surface of the CPE, followed by oxidation of adsorbed species. The optimal experimental conditions include the use of 0.10 mol · L⁻¹ ammonium acetate buffer (pH 4.3), ARS, an accumulation potential of 0.20 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV · s⁻¹ and a second-order derivative linear scan mode. The oxidation peak for the complex appears at 0.69 V. The peak current is proportional to the concentration of Zr(IV) over the range of 1.0 × 10⁻⁹–2.0 × 10⁻⁷ mol · L⁻¹, and the detection limit is 3 × 10⁻¹⁰ mol · L⁻¹ for a 2 min adsorption time. The relative standard deviations (n = 8) for 5.0 × 10⁻⁸ and 5.0 × 10⁻⁹ mol · L⁻¹ Zr(IV) are 3.3 and 4.8%, respectively. The proposed method was applied to the determination of zirconium in ore samples with satisfactory results.     

Differential pulse polarographic study of thiamine (vitamin B1) in neutral and acidic aqueous solutions

The differential pulse (dp) polarograms of thiamine in neutral aqueous solutions exhibited six peaks at low depolarizer concentration (⋦10⁻⁴ mol dm⁻³) and only three peaks at concentrations ≥10⁻³ mol dm⁻³. Only one of these was found to correspond to the diffusion-controlled reduction of this compound at the dme and this was shown to be an irreversible two-electron process. The kinetic parameters derived from the dp polarograms were found to be in good agreement with those calculated from classical polarograms and were:E _1/2=−1·261 Vvs SCE,an _a=0·54 andD≈3·5×10⁻⁶ cm² sec⁻¹ for 10⁻³ mol dm⁻³ thiamine in 0·1 mol dm⁻³ acetate buffer (pH 6·5). The reduction product has been identified as dihydrothiamine. The effect of pH on the dpp of thiamine was studied in the pH range 0–7. In the pH region 5·5 to 7·0 only one peak attributable to the B₁ ⁺ form of thiamine is present. In the pH region 3·5–5·5 another dpp peak attributable to the protonated form (B₁H²⁺) of thiamine was also observed. At pHs less than 3 only one peak was observed which could be attributed to the doubly protonated form (B₁ H₂ ³⁺) of thiamine. Surfactants like triton-X-100 and CTABr were found to inhibit the electroreduction of thiamine due to the strong adsorption of these compounds on the dme. Thiamine itself was found to have an inhibitory effect on its own electroreduction, although to a smaller extent.     

Chemometrics to evaluate the quality of water sources for human consumption

Multilayer films of multiwalled carbon nanotubes (MWNTs) were homogeneously and stably assembled on a glassy carbon (GC) electrode using the layer-by-layer (LBL) method based on electrostatic interaction between MWNTs (negatively charged) and a biopolymer chitosan (CHIT) (positively charged). Scanning electron microscopy (SEM) image of the resulting {CHIT/MWNTs}₉ film indicated that the substrate was mostly covered with MWNTs in the form of small bundles or single nanotubes. The multilayer film was used to study the electrocatalytic oxidation of NADH. The assembled {CHIT/MWNTs}₉/GC electrode could decrease the oxidation overpotential of NADH by more than 350 mV. The {CHIT/MWNTs}₉/GC electrode exhibited a wide linear response range of 8 × 10⁻⁷ to 1.6 × 10⁻³ mol · L⁻¹ with a correlation coefficient of 0.997 for the detection of NADH. The response time and detection limit (S/N = 3) were determined to be 3 s and 0.3 × 10⁻⁶ mol · L⁻¹, respectively. Another attractive characteristic was that the method was simple and the assembled {CHIT/MWNTs}₉/GC electrode was highly stable.     

Electrochemistry and electrocatalytic activity of polypyrrole/ferrocyanide films on a glassy carbon electrode

Functionalized polypyrrole films were prepared by incorporation of Fe(CN)₆ ³⁻ as doping anion during the electropolymerization of pyrrole at a glassy carbon electrode from aqueous solution. The electrochemical behavior of the Fe(CN)₆ ³⁻/Fe(CN)₆ ⁴⁻ redox couple in polypyrrole was studied by cyclic voltammetry. An obvious surface redox reaction was observed and dependence of this reaction on the solution pH was illustrated. The electrocatalytic ability of polypyrrole film with ferrocyanide incorporated was demonstrated by oxidation of ascorbic acid at the optimized pH of 4 in a glycine buffer. The catalytic effect for mediated oxidation of ascorbic acid was 300 mV and the bimolecular rate constant determined for surface coverage of 4.5 × 10⁻⁸ M cm⁻² using rotating disk electrode voltammetry was 86 M⁻¹ s⁻¹. Furthermore, the catalytic oxidation current was linearly dependent on ascorbic acid concentration in the range 5 × 10⁻⁴–1.6 × 10⁻² M with a correlation coefficient of 0.996. The plot of i _p versus v ^1/2 confirms the diffusion nature of the peak current i _p. Received: 12 April 1999 / Accepted: 25 May 1999     

Kinetics of the Formation of the Blue Complex CrO(O2)2 Formed by Dichromate and H2O2 in Acid Solutions. A Stopped-Flow Investigation Using Rapid-Scan UV-VIS Detection

Summary.  The kinetics of the CrO(O₂)₂ formation by H₂O₂ and Cr₂O₇ ²⁻ in aqueous acidic media was measured at 293 ± 2 K in a pH range between 2.5 and 3.3. Using the stopped-flow method with rapid scan UV-VIS detection, the rate law of the formation of CrO(O₂)₂ was determined. For the media HClO₄, HNO₃ and CH₃COOH, the reaction order in the Cr₂O₇ ²⁻ concentration was found to be 0.5. For [H₂O₂] as well as for [H⁺], the reaction was first order in all acids used. In HCl and H₂SO₄ media the reaction was first order in Cr₂O₇ ²⁻. At T = 293 ± 2 K the rate constant for the formation of Cr(O)(O₂)₂ was found to be (7.3 ± 1.9) · 10² M^−3/2 s⁻¹ in HClO₄. Corresponding author. E-mail: grampp@ptc.tu-graz.ac.at Received January 30, 2002; accepted (revised) June 5, 2002     

Flow-injection analysis for the determination of total inorganic carbon and total organic carbon in water using the H2O2–luminol–uranine chemiluminescent reaction

In the presence of carbonate and uranine, the chemiluminescent intensity from the reaction of luminol with hydrogen peroxide was dramatically enhanced in a basic medium. Based on this fact and coupled with the technique of flow-injection analysis, a highly sensitive method was developed for the determination of carbonate with a wide linear range. The method provided the determination of carbonate with a wide linear range of 1.0 × 10⁻¹⁰–5.0 × 10⁻⁶ mol L⁻¹ and a low detection limit (S/N = 3) of carbonate of 1.2 × 10⁻¹¹ mol L⁻¹. The average relative standard deviation for 1.0 × 10⁻⁹–9.0 × 10⁻⁷ mol L⁻¹ of carbonate was 3.7% (n = 11). Combined with the wet oxidation of potassium persulfate, the method was applied to the simultaneous determination of total inorganic carbon (TIC) and total organic carbon (TOC) in water. The linear ranges for TIC and TOC were 1.2 × 10⁻⁶–6.0 × 10⁻² mg L⁻¹ and 0.08–30 mg L⁻¹ carbon, respectively. Recoveries of 97.4–106.4% for TIC and 96.0–98.5% for TOC were obtained by adding 5 or 50 mg L⁻¹ of carbon to the water samples. The relative standard deviations (RSDs) were 2.6–4.8% for TIC and 4.6–6.6% for TOC (n = 5). The mechanism of the chemiluminescent reaction was also explored and a reasonable explanation about chemical energy transfer from luminol to uranine was proposed. Figure Chemiluminescence profiles in batch system. 1, Injection of 100 μL of K₂CO₃ into 1.0 mL luminol-1.0 mL H₂O₂ solution; 2-3 and 4-5, Injection in sequence of 100 μL of K₂CO₃ and 100 μL of uranine into 1.0 ml luminol-1.0 mL H₂O₂ solution; C_luminol = 1.0 × 10⁻⁷ mol/L, C_H2O2 = 1.0 × 10⁻⁵ mol/L, C_uranine = 1.0 × 10⁻⁵ mol/L, C_K2CO3 = 1.0 × 10⁻⁷ mol/L except for 4-5 where C_K2CO3 = 1.0 × 10⁻⁴ mol/L     

Determination of Selenium in Biological Materials Using an Ion-Selective Electrode

A method was developed for determining selenium with a self-made ion-selective electrode was developed. This electrode was made by using Ag₂Se as electroactive material. Optimal working conditions and interferences were investigated. The electrode exhibits good potentiometric response for Se²⁻ ions over the concentration range from 6 × 10⁻⁷ mol · L⁻¹ to 1 × 10⁻⁴ mol · L⁻¹ with a Nernstian slope of 28 ± 1 mV per decade and a detection limit of about 4.5 × 10⁻⁷ mol · L⁻¹. It was used over six months and exhibits good selectivity and sensitivity towards Se²⁻. The method was applied to determine selenium in biological materials. The recovery ranges between 92% and 105.5%, and the relative standard derivation is less than 3.6% (n = 6).