Germania-glass-core silica-glass-cladding modified chemical-vapor deposition optical fibers: optical losses, photorefractivity, and Raman amplification

Germania-glass-core silica-glass-cladding single-mode fibers (deltan as great as 0.143) with a minimum loss of 20 dB/km at 1.85 microm were fabricated by modified chemical-vapor deposition. The fibers exhibit strong photorefractivity, with type IIa index modulation of 2 x 10(-3). A Raman gain of 300 dB/(kmW) was determined at 1.12 microm. Only 3 m of such fibers is sufficient for constructing the 10-W Raman laser at 1.12 microm with a 13-W pump at 1.07 microm.     

大功率激光单模光纤远距离传输的注入光纤光功率限值分析

对于大功率激光单模光纤远距离传输, 采用传统的受激拉曼散射(SRS)阈值作为注入光纤激光功率值取值过大。本文对单模光纤远距离传输过程中泵浦光和拉曼斯托克斯光(Stokes)光功率随注入光纤激光功率的变化进行仿真与理论分析。根据光纤中SRS产生的机理, 提出以拉曼Stokes光在单模光纤中传输的光功率变化曲线曲率极大值点对应的注入激光功率为限值, 对注入单模光纤光功率限值随着光纤长度变化进行仿真, 通过曲线拟合得出注入单模光纤激光功率限值公式, 并搭建实验系统进行验证。结果表明, 提出的注入单模光纤激光功率限值适用于大功率激光远距离单模光纤传输。     

高功率纳秒光脉冲在单模光纤中的受激喇曼散射及抑制研究

利用包含喇曼增益、抽运消耗、自相位调制、交叉相位调制和群速度色散效应的耦合非线性薛定谔方程组,对千瓦级高功率纳秒脉冲在单模光纤中的传输特性进行了模拟计算.分析了输入脉冲和斯托克斯脉冲的演化过程,研究了大模面积光纤对受激喇曼散射的抑制作用.研究结果表明,采用模面积为530 μm~2的光子晶体光纤作为惯性约束聚变脉冲整形系统的传输介质,能有效抑制受激拉曼散射,不但信号衰减较小,而且中心凹陷程度较低.     

High-power continuous-wave cladding-pumped Raman fiber laser

We demonstrate a high-power single-mode cladding-pumped Raman fiber laser. The Raman fiber laser consists of a 1.2 km long germanium-doped double-clad fiber in a linear cavity, which is spliced to a single-mode fiber. The laser is end pumped by a multimode erbium-ytterbium-doped fiber, which is coupled to the inner cladding of the Raman fiber. The embedded core was designed to be single mode at the Raman Stokes wavelength, and up to 10 W of power was obtained at 1660 nm from the single-mode fiber end. The laser has a slope efficiency of 67% and a threshold of 6.5 W.     

Holmium-doped fluoride fiber laser at 2950 nm pumped at 1175 nm

We report a single-mode, highly stable, continuous-wave Ho³⁺: ZBLAN fiber laser. The system was pumped by a 1175-nm fiber Raman laser and emitted at ～2950 nm. The optical-to-optical conversion efficiency was 43% that is the highest reported in the literature. Characterizations revealed a quasigaussian intensity profile with a power stability of less than 1%. This high stability relies on the single-wavelength emission of the system because the system does not require simultaneous oscillation at 2100 nm. Coincidence between the emission wavelength and the absorption peak of water makes the system suitable to replace a high-power (～9.34-W) Er³⁺: ZBLAN fiber laser for cutting materials with high moisture content.     

Monolithic integration of electroabsorption modulator and DFB laser for 10-Gb/s transmission

A strained InGaAsP-InP multiple-quantum-well DFB laser monolithically integrated with electroabsorption modulator by ultra-low-pressure (22 mbar) selective-area-growth is presented. The integrated chip exhibits superior characteristics, such as low threshold current of 19 mA, single-mode operation around 1550 nm range with side-mode suppression ratio over 40 dB, and larger than 16 dB extinction ratio when coupled into a single-mode fiber. More than 10 GHz modulation bandwidth is also achieved. After packaged in a compact module, the device successfully performs 10-Gb/s NRZ transmission experiments through 53.3 km of standard fiber with 8.7 dB dynamic extinction ratio. A receiver sensitivity of −18.9 dBm at bit-error-rate of 10⁻¹⁰ is confirmed.     

基于多波长激光器的带通微波光子滤波器设计

提出了一种基于多波长光纤激光器的可调谐的带通微波光子滤波器。它以可调谐多波长光纤激光器作为光源,将相位调制器和色散器件相结合,通过在普通单模光纤中相位调制到强度调制的转换效应消除了低频谐振峰实现了带通微波光子滤波器。利用双折射光纤环镜输出谱中的一个窗口对多波长激光信号频谱进行加窗处理,使微波光子滤波器的边瓣抑制比提高了约11dB。通过调节多波长光纤激光器中的偏振控制器可以使输出多波长激光信号的相邻波长间隔得到调节,从而结合普通单模光纤的色散延时作用可以使微波光子滤波器的通带中心频率在7.66GHz范围内调谐。     

Actively mode-locked fiber ring laser by intermodal acousto-optic modulation

We report an actively mode-locked fiber ring laser. A simple and low-insertion-loss acousto-optic modulator driven by standing flexural waves, which couples core-to-cladding modes in a standard single-mode optical fiber, is used as an active mechanism for mode locking. Among the remarkable features of the modulator, we mention its high modulation depth (72%), broad bandwidth (187 GHz), easy tunability in the optical wavelength, and low insertion losses (0.7 dB). The narrowest optical pulses obtained were of 95 ps time width, 21 mW peak power, repetition rate of 4.758 MHz, and 110 mW of pump power.     

126-W all-fiberized single-mode laser from an 11-μm small-core fiber

We demonstrate a 126-W all-fiberized single-mode laser from an 11-μm small-core fiber. The active fiber is a strictly single-mode fiber that produces pure single-mode. The optical to optical efficiency of the fiber laser is 68.2% with ASE suppressed by a factor of ∼35 dB and no power-roll. The output power is only limited by the available pump source, scaling the pump power may achieve much higher output power using the 11 μm small-core fiber.     

Experimental study of an actively mode-locked fiber ring laser based on in-fiber amplitude modulation

We report an experimental study of an actively mode-locked fiber ring laser based on the development of an efficient in-fiber amplitude modulator. Intermodal coupling induced by standing flexural acoustic waves permits the implementation of broad bandwidth (1.5 nm), high modulation depth (72%), low-insertion-loss (0.75 dB), in-fiber amplitude modulators, operating in the MHz frequency range. The experimental characterization of the laser as a function of the radio frequency voltage that controls the modulator, the length of the active fiber, and the optical bandwidth of an intracavity filter implemented with a fiber Bragg grating has led to an improved performance of the Erbium-doped fiber laser: optical pulses of 34-ps temporal width, 1.4-W peak power, and 4.75-MHz repetition rate.     

Co(2+)-doped flatband optical fiber attenuator

The attenuation properties of Co(2+) -doped single-mode optical fibers were experimentally and analytically investigated for preparation of a stable flatband attenuator. By controlling the Co(2+) -doped region in a fiber core, we could prepare a flatband attenuator in which the attenuation in wavelengths 1530-1610 nm was held to within 9.9-10.2 dB (3% variation) and the fluctuation of attenuation was less than 0.1 dB with 1-W input power for 100 h.     

高重复频率锁模光纤激光器及其超连续谱产生

设计并实验研究了一种结构简单的主动调制锁模高重复频率窄脉宽光纤激光器。采用窄线宽连续激光调制4 GHz高重频后,通过拉曼增益孤子压缩效应将脉宽由27 ps压窄至2.6 ps。该高重频锁模激光泵浦一段300 m长高非线性光纤,同时脉冲被展宽至7.4 ps。产生的超连续谱平坦度20 dB宽带可达250 nm,功率波动为±0.2 dB。     

High-power,low-noise,Yb-doped,cladding-pumped,three-level fiber sources at 980 nm

We present results on a high-power, cladding-pumped, Yb-doped fiber emitting at 977 nm in laser and ampllified-spontaneous-emission source configurations. We obtained up to 1.4 W of fiber-coupled, single-mode output power and slope efficiency as high as 68%. To our knowledge these are the highest powers efficiencies achieved from a single-mode fiber laser at approximately 980 nm and the first demonstrated results on a high-power amplified-spontaneous-emission source in this wavelength range. High power and high slope efficiency are achieved by using a high numerical aperture (> 0.7), a jacketed air-clad fiber, and a high-brightness pump source. Both types of sources exhibit relative intensity noise below -130 dB/Hz and are thus suitable for a wide range of applications.     

Integration of electro-optic polymer modulators with low-loss fluorinated polymer waveguides

We have demonstrated a hybrid Mach-Zehnder optical modulator consisting of a large-core, low-loss fluorinated passive polymer waveguide and an electro-optic (EO) polymer waveguide. The combination exhibits low fiber coupling loss to the passive waveguide and reduced transmission loss because the EO polymer waveguide is used only in the active region. The two waveguides are connected by vertical tapers that permit low-loss adiabatic coupling between the two modes. The half-wave voltage and the insertion loss of the fabricated modulator are 3.6 V and 6 dB, respectively, at a wavelength of 1.55 microm . The estimated coupling loss with the standard single-mode fiber is ~0.5 dB.     

Widely tunable ring-cavity tellurite fiber Raman laser

We report a widely tunable ring-cavity tellurite fiber Raman laser covering the S+C+L+U band. A tunable range (1495-1600 nm, limited by the tunable optical bandpass filter) over 100 nm is obtained by using a single-mode tellurite fiber with high Raman gain coefficients (55 W(-1)km(-1)) and large Raman shift (~22.3 THz) as the gain medium. Furthermore, the free-running 1665 nm Raman fiber laser is achieved from the ring cavity by removing the tunable optical bandpass filter, which shows that such a tellurite fiber has potential for constructing a widely tunable fiber Raman laser covering the S+C+L+U band. A high optical signal-to-noise ratio of over 60 dB for almost all of the tunable range is also demonstrated.     

Soliton splitting in a dispersion-oscillating fiber

A single-mode fiber with a sinusoidal variation of the core diameter was fabricated. The soliton splitting due to the longitudinal oscillation of the fiber dispersion is demonstrated experimentally. The experimental observations are confirmed through numerical simulations. The periodical modulation of the fiber dispersion can be used for controlling the soliton splitting even under the strong effect of the Raman scattering.     

High-power, single-mode, linearly polarized, ytterbium-doped fiber superfluorescent source

High-power operation of a single-mode, linearly polarized, broadband superfluorescent fiber source has been achieved by using a two-stage cladding-pumped fiber configuration comprising a low power, single-ended, ytterbium-doped superfluorescent fiber seed source and a high-power cladding-pumped, polarization-maintaining, large-mode-area, ytterbium-doped amplifier pumped by a high-power diode source at 976 nm. The source yielded a maximum linearly polarized output of 106 W with a slope efficiency of up to 67% with respect to the launched pump power and with a measured polarization extinction ratio of 13.5 dB. The wavelength spectrum of the superfluorescent source spanned the range continuously from ~1035 to 1100 nm, and the bandwidth (FWHM) of the emission spectrum was 21 nm. The minimum seed power required for an output power over 100 W was only 10 mW, corresponding to an effective power gain in the amplifier stage of 40 dB. Single-spatial-mode operation with a beam propagation factor (M(2))<1.1 was achieved by bending the amplifier fiber to a bend radius of ~8 cm, without a significant reduction in output power.     

Measurement of the chromatic dispersion of an optical fiber by use of a Sagnac interferometer employing asymmetric modulation

We describe a novel method, based on asymmetric modulation in a Sagnac interferometer, that measures the chromatic dispersion of single-mode fibers. The interferometer incorporates a phase modulator and a test fiber, so the dispersion can be determined from the interference fringe seen when a sweep rf signal is applied to the modulator. This technique provides picosecond temporal resolution without the need for any fast diagnostic equipment and is capable of accurately measuring the average dispersion of fibers several kilometers long.     

High-power single-mode emission from a broad-area semiconductor laser with a pseudoexternal cavity and a Fabry Perot etalon

A simple pseudoexternal cavity with a commerically available broad-area laser diode, standard optics, and a thin FabryPerot etalon provides single-mode emission with 1-W optical power and a tuning range of ~0.5nm . The linewidth is estimated at 200MHz. Such high-power semiconductor laser systems are promising light sources for atomic physics, in which narrow-band high-power light is necessary, for example, for optical pumping of alkali metal vapor. Methods for expanding the tuning range and achieving higher narrow-band optical power are discussed.     

单模光纤中喇曼类孤子脉冲理论研究

本文在考虑群速度色散(GVD)、受激喇曼散射(SRS)、自相位调制(SPM)、交叉相位调制(XPM)及光纤损耗同时作用的条件下,建立了关于单模光纤中喇曼类孤子的理论计算模型。通过模拟计算Gouveia-neto等人的实验,得到了84fs的喇曼类孤子脉冲,与其实验结果基本一致,并给出了喇曼类孤子脉冲形成过程的图象和新见解。 关键词：