Photocatalytic degradation of trichloroethylene on platinum ion-doped TiO<Subscript>2</Subscript> under visible light irradiation

Porous platinum ion-doped TiO₂ (Pt–TiO₂) was prepared by a sol–gel method and demonstrated to have superior photocatalytic activity for the photodegradation of gaseous trichloroethylene (TCE) under visible light (VL) irradiation from a xenon lamp equipped with 422-nm cut-off filter. Kinetic studies were performed to clarify the effect of the doping amounts, space times, VL intensity, and mole fractions of TCE, O₂, and H₂O on the degradation of TCE. Under ultraviolet (UV) irradiation, the photocatalytic activity of Pt–TiO₂ was the same as that of TiO₂, indicating that the doped Pt ion did not act as a recombination center for the photogenerated holes and electrons. Based on the kinetic data and reaction products, we conclude that the photocatalytic degradation of TCE on Pt–TiO₂ under VL irradiation proceeds similarly to TiO₂ under UV irradiation. We also performed the photocatalytic degradation of TCE at the space time of 7.5 × 10⁷ g s mol^?1 in a tubular reactor packed with the Pt–TiO₂ pellets which are more suitable than the Pt–TiO₂ powder for the practical remediation of the contaminated gas. TCE was completely degraded, i.e. 100% conversion was achieved under VL irradiation but only a small quantity of CO₂ was formed with the stoichiometric ratio of [CO₂]_formed/[TCE]_degraded of ca. 0.33. By switching the gas stream containing TCE to humid air, more CO₂ was formed, indicating that the dichloroacetates accumulated on the Pt–TiO₂ surface are photodegradable to CO₂ under VL irradiation.     

Analysis of preparation of TiO<Subscript>2</Subscript> particles by diffusion flame reactor for photodegradation of phenol and toluene

TiO₂ nanoparticles were produced in the diffusion flame reactor, and the size and anatase/rutile content of TiO₂ were examined by a Particle Size Analyzer and X-ray diffraction, respectively. Increase in fuel/O₂ ratio, initial concentration of TiCl₄ or total gas flow rate causes the larger particle size and the higher rutile composition. The photocatalytic activities of TiO₂ powders were tested on the decompositions of phenol and toluene in the aqueous solution under UV irradiation. The degradation rate increases as the TiO₂ particle size decreases and as the initial concentration of phenol or toluene increases. The photodegradation rate of phenol by TiO₂ particles is higher than that of toluene at the same process conditions. The computational method was used to simulate the gas temperature, velocity and species mass fractions inside the diffusion flame reactor during synthesis of TiO₂ nanoparticles. The measured and simulated temperature results were compared on several positions above the burner and both of them show good agreements. The typical contours of TiCl₄, TiO₂ mass fractions and gas velocities in flame reactor were presented.     

Simultaneous removal of NO and SO<Subscript>2</Subscript> in a plasma reactor packed with TiO<Subscript>2</Subscript>-coated glass beads

We analyzed the dielectric pellet bed discharge-photocatalyst hybrid process for NO and SO₂ removal. A cylindrical-wire type discharge reactor was packed with glass beads as dielectric pellets and the plasmas were generated by dielectric pellet bed discharge. The TiO₂ photocatalysts were coated onto the glass beads by the dip-coating method and were activated by the light from discharge. Experiments were carried out for three cases: NO removal only, SO₂ removal only, and simultaneous NO and SO₂ removal. As the voltage applied to the plasma reactor increased, or as the residence time increased, the NO and SO₂ removal efficiencies increased. With increasing initial NO and SO₂ concentrations, the NO and SO₂ removal efficiencies decrease. The removal efficiencies for simultaneous NO and SO₂ removal are lower than those for NO only or SO₂ only.     

Preparation and Characterisation of Nano-Structured WO<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Layers for Photoelectrochromic Devices

Nano-structured WO₃-TiO₂ layers were prepared by the sol-gel route. To obtain transparent, porous and crack free layers up to 0.8 μ m with a single dipping cycle a templating strategy was used. As a template three-dimensionally network based on organically modified silane was introduced to the WO₃ and TiO₂ sols. The WO₃ layers were dip-coated onto the conductive glass substrate (TCO) and the TiO₂ layers on the top of the WO₃ layer. The morphology and the structure of the layers were determined by Scanning Electron Microscopy (SEM), High Resolution Transmission Electron Microscopy (HR-TEM), Energy Dispersive X-Ray Spectroscopy (EDXS), Auger and Infrared spectroscopy. SEM image of the WO₃-TiO₂ layer confirmed the nano-porosity of the layers and give the size of the particles of about 10 nm for TiO₂ and 30 nm for WO₃ layer. Further analysis indicated that the titanium sol penetrates the WO₃ layer. Particles in the WO₃ layer consist of a crystalline monoclinic WO₃ core surrounded by a 5–10 nm amorphous phase consisting of WO₃, TiO₂ and SiO₂. The WO₃-TiO₂ layers were used to assemble all solid state photoelectrochromic (PE) devices. Under 1 sun irradiation (1000 W/m²) the visible transmittance of the PE device changes from 62% to 1.6%. The colouring and bleaching processes last about 10 minutes.     

Oxidation of Dimethyl Sulfide in Air Using Electron-Beam Irradiation,and Enhancement of its Oxidation Via an MnO<Subscript>2</Subscript> Catalyst

The decomposition of dimethyl sulfide (DMS) at initial concentrations of 4.5–18.0 ppmv in air was studied under electron-beam (EB) irradiation. Doses to decompose 90% of input DMS were 2.5 kGy for 4.5 ppmv, 3.4 kGy for 10.6 ppmv, and 3.9 kGy for 18.0 ppmv. HCOOH, (CH₃)₂SO, and trace CH₃OH and (CH₃)₂SO₂ were produced as irradiation products in addition to CO₂ and CO. Application of an O₃ decomposition catalyst to an irradiated sample gas led to an enhancement in the oxidation of DMS and its products into CO₂ and the decomposition of O₃. For 10.6 ppmv DMS/air, the mineralization ratio increased from 41% via only EB irradiation to 100% via the combination treatment at 6.3 kGy. The yield of CO₂ to CO_x increased from 5.3 to 87.6% by combination with catalytic oxidation. This combination treatment enables the irradiation energy used to deodorize gas streams containing DMS to be reduced.     

Dielectric properties and I-V characteristics of (Pb<Subscript>0.4</Subscript>Sr<Subscript>0.6</Subscript>)TiO<Subscript>3</Subscript> thin films improved by TiO<Subscript>2</Subscript> buffer layers

A TiO₂ thin buffer layer was introduced between the (Pb_0.4Sr_0.6)TiO₃ (PST) film and the Pt/Ti/SiO₂/Si substrate in an attempt to improve their electrical properties. Both TiO₂ and PST layers were prepared by a chemical solution deposition method. It was found that the TiO₂ buffer layer increased the (100)/(001) preferred orientation of PST and decreased the surface roughness of the films, leading to an enhancement in electrical properties including an increase in dielectric constant and in its tunability by DC voltage, as well as a decrease in dielectric loss and leakage current density. At an optimized thickness of the TiO₂ buffer layer deposited using 0.02 mol/l TiO₂ sol, the 330-nm-thick PST films had a dielectric constant, loss and tunability of 1126, 0.044 and 60.7% at 10 kHz, respectively, while the leakage current density was 1.95 × 10⁻⁶ A/cm² at 100 kV/cm.     

Photocatalytic degradation of dichloroacetyl chloride adsorbed on TiO<Subscript>2</Subscript>

Dichloroacetyl chloride (DCAC) attracted our attention as an intermediate product of the photocatalytic degradation of trichloroethylene (TCE). The adsorption and photocatalytic reaction of DCAC on TiO₂ have been investigated by FTIR spectroscopy. The influence of the surface structure of several TiO₂s on the reaction mechanism was discussed in order to understand the complete degradation mechanism of TCE as well as DCAC. DCAC was transformed into dichloroacetic acid (DCAA) on the relatively hydrophobic TiO₂ surface by the small amount of the water molecules weakly adsorbed on the surface. This DCAA was degraded to phosgene, CO₂, and CO during UV irradiation. For the hydrophilic TiO₂, DCAC was mainly transformed into the dichloroacetate anion. UV irradiation allowed this species to produce chloroform in addition to phosgene, CO₂, and CO. It is suggested that DCAC easily reacts with the Ti–OH group on the hydrophilic TiO₂ and forms the bidentate titanium chelate of dichloroacetate, which efficiently degrades into chloroform.     

Effect of PEG with different <Emphasis Type="Italic">M</Emphasis><Subscript>W</Subscript> as template direction reagent on preparation of porous TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> with assistance of supercritical CO<Subscript>2</Subscript>

Titania–silica composite have been prepared using polyethylene glycol (PEG) with different molecular weights (M _w), PEG20000, PEG10000, and PEG2000, as template in supercritical carbon dioxide (SC CO₂). The composite precursors were dissolved in SC CO₂ and impregnated into PEG templates using SC CO₂ as swelling agent and carrier. After removing the template by calcination at suitable temperature, the titania–silica composite were obtained. The composite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and nitrogen sorption–desorption experiment. Photocatalytic activity of the samples has been investigated by photodegradation of methyl orange. Results indicate that there are many Si–O–Ti linkages in the TiO₂/SiO₂ composite; the PEG template has a significant influence on the structure of TiO₂/SiO₂. In addition, the TiO₂/SiO₂ prepared with PEG10000 exhibited high photocatalytic efficiency. So this work supplies a clue to control and obtain the TiO₂/SiO₂ composite with different photocatalytic reactivity with the aid of suitable PEG template in supercritical CO₂.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

Fabrication and characterization of TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite nanoparticles and polyurethane/(TiO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript>) nanocomposite films

TiO₂–SiO₂ composite nanoparticles were prepared by a sol–gel process. To obtain the assembly of TiO₂–SiO₂ composite nanoparticles, different molar ratios of Ti/Si were investigated. Polyurethane (PU)/(TiO₂–SiO₂) hybrid films were synthesized using the “grafting from” technique by incorporation of modified TiO₂–SiO₂ composite nanoparticles building blocks into PU matrix. Firstly, 3-aminopropyltriethysilane was employed to encapsulate TiO₂–SiO₂ composite nanoparticles’ surface. Secondly, the PU shell was tethered to the TiO₂–SiO₂ core surface via surface functionalized reaction. The particle size of TiO₂–SiO₂ composite sol was performed on dynamic light scattering, and the microstructure was characterized by X-ray diffraction and Fourier transform infrared. Thermogravimetric analysis and transmission electron microscopy (TEM) employed to study the hybrid films. The average particle size of the TiO₂–SiO₂ composite particles is about 38 nm when the molar ratio of Ti/Si reaches to1:1. The TEM image indicates that TiO₂–SiO₂ composite nanoparticles are well dispersed in the PU matrix.     

Structural characterization and photocatalytic properties of novel Bi<Subscript>2</Subscript>FeVO<Subscript>7</Subscript>

Bi₂FeVO₇ was prepared by a solid-state reaction technique for the first time and the structural and photocatalytic properties of Bi₂FeVO₇ were studied. The results shows that this compound crystallized in the tetragonal crystal system with space group I4/mmm. Moreover, the band gap of Bi₂FeVO₇ was estimated to be about 2.22(6) eV. For the photocatalytic water splitting reaction, H₂ or O₂ evolution was observed from pure water with Bi₂FeVO₇ as the photocatalyst by ultraviolet light irradiation. Degradation of aqueous methylene blue (MB) dye by photocatalytic way over this compound was further studied under visible light irradiation. Bi₂FeVO₇ shows higher catalytic activity compared to TiO₂ (P-25) for MB photocatalytic degradation under visible light irradiation. Complete removal of aqueous MB was realized after visible light irradiation for 170 min with Bi₂FeVO₇ as the photocatalyst. The reduction of the total organic carbon (TOC) and the formation of inorganic products, SO ₄ ²⁻ and NO ₃ ⁻ revealed the continuous mineralization of aqueous MB during the photocatalytic course.     

Effect of TiO<Subscript>2</Subscript> on Various Regions of Active Electrode on Surface Dielectric Barrier Discharge in Air

For surface dielectric barrier discharge in air, we examined the effect of titanium dioxide on various regions of the active electrode on the electrical parameters of discharge, on its emission spectra, and for demonstration of the obtained results also on the concentration of ozone produced by the discharge. We used the active electrode in the form of nine interconnected parallel strips and a square counter electrode. The TiO₂ layer covered either only the strips, the region between the strips, or all active electrode. As reference discharge we used the discharge without any layer of TiO₂. We found that direct application potential has a version when the strips of the active electrode are covered with a layer of TiO_2, because the concentration of ozone produced by the discharge is the highest in all investigated cases. This finding could therefore be used for construction of more efficient ozone generators.     

Hierarchically nanostructured porous TiO<Subscript>2</Subscript>(B) with superior photocatalytic CO<Subscript>2</Subscript> reduction activity

Hierarchically nanostructured, porous TiO₂(B) microspheres were synthesized by a microwave-assisted solvothermal method combined with subsequent heat treatment in air. The materials were carefully characterized by scanning and transmission electron microscopy, X-ray diffraction, CO₂ adsorption, and a range of spectroscopies, including Raman, infrared, X-ray photoelectron and UV-Vis spectroscopy. The hierarchical TiO₂(B) particles are constructed by ultrathin nanosheets and possess large specific surface area, which provided many active sites for CO₂ adsorption as well as CO₂ conversion. The TiO₂(B) nanostructures exhibited marked photocatalytic activity for CO₂ reduction to methane and methanol. Anatase TiO₂ and P₂5 were used as the reference photocatalysts. Transient photocurrent measurement also proved the higher photoactivity of TiO₂(B) than that of anatase TiO₂. In-situ infrared spectrum was measured to identify the intermediates and deduce the conversion process of CO₂ under illumination over TiO₂(B) photocatalyst.     

Dry Potassium-Based Sorbents for CO<Subscript>2</Subscript> Capture

Dry potassium-based sorbents were prepared by impregnation with potassium carbonate on supports such as activated carbon (AC), TiO₂, Al₂O₃, MgO, CaO, SiO₂ and various zeolites. The CO₂ capture capacity and regeneration property of various sorbents were measured in the presence of H₂O in a fixed bed reactor, during multiple cycles at various temperature conditions (CO₂ absorption at 50–100 °C and regeneration at 130–400 °C). The KAlI30, KCaI30, and KMgI30 sorbents formed new structures such as KAl(CO₃)₂(OH)₂, K₂Ca(CO₃)₂, K₂Mg(CO₃)₂, and K₂Mg(CO₃)₂·4(H₂O), which did not completely convert to the original K₂CO₃ phase at temperatures below 200 °C, during the CO₂ absorption process in the presence of 9 vol.% H₂O. In the case of KACI30, KTiI30, and KZrI30, only a KHCO₃ crystal structure was formed during CO₂ absorption. The formation of active species, K₂CO₃·1.5H₂O, by the pretreatment with water vapor and the formation of the KHCO₃ crystal structure after CO₂ absorption are important factors for absorption and regeneration, respectively, even at low temperatures (130–150 °C). In particular, the KTiI30 sorbent showed excellent characteristics with respect to CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (87 mg CO₂/g sorbent) without the pretreatment with water vapor, unlike KACI30, and a fast and complete regeneration at a low temperature condition (1 atm, 150 °C). In addition, the higher total CO₂ capture capacity of KMgI30 (178.6 mg CO₂/g sorbent) than that of the theoretical value (95 mg CO₂/g sorbent) was explained through the contribution of the absorption ability of MgO support. In this review, we introduce the CO₂ capture capacities and regeneration properties of several potassium-based sorbents, the changes in the physical properties of the sorbents before/after CO₂ absorption, and the role of water vapor and its effects on CO₂ absorption.     

Decomposition of Toluene and Acetone in Packed Dielectric Barrier Discharge Reactors

The influences of TiO₂ catalytic material and glass pellet packing on the decomposition efficiency of toluene and acetone in air by dielectric barrier discharge (DBD) reactors were experimentally investigated in this study. The effects of both packing materials on the formation of byproducts such as CO and CO₂ were also evaluated. Experimental results indicate that the introduction of glass materials into the plasma zone of a wire-tube reactor would improve the decomposition efficiency of toluene and acetone compared to a nonpacked reactor. The apparent decomposition rate constant of a glass packed-bed reactor was 4.5–4.8 times greater than that of a nonpacked reactor. The results also indicate that the decomposition rate constant of toluene was approximately 2.6 times higher than that of acetone no matter which type reactor was utilized. The application of TiO₂ coated pellets in DBD reactors will enforce the hydrocarbon byproducts to further be oxidized to CO₂, notwithstanding, it will not significantly improve the performance of the reactors in the decomposition of toluene and acetone, and in the formation of CO. The results show that the best selectivity of CO₂ for acetone decomposition in a TiO₂ coated pellets packed-bed reactor was approximately 40% higher than that in a glass packed-bed reactor.     

TiO<Subscript>2</Subscript>-based nanopowders obtained from different Ti-alkoxides

Pure TiO₂ and S-doped TiO₂ sol–gel nanopowders were prepared by controlled hydrolysis-condensation of titanium alkoxides. The influence of different Ti-alkoxides (tetraethyl-, tetraisopropyl- and tetrabutyl-orthotitanate) used in obtaining TiO₂ porous materials in similar conditions (water/alkoxide ratio, solvent/alkoxide ratio, pH and temperature of reaction) has been investigated. The relationship between the synthesis conditions and the properties of titania nanosized powders, such as thermal stability, phase composition, crystallinity, morphology and size of particles, BET surface area and the influence of dopant was investigated. The nature of the alkyl group strongly influences the main characteristics of the obtained oxide powders, fact which is pointed out by thermal analysis, X-ray diffraction, TEM and BET surface area measurements.     

Photocatalytic reduction of CO<Subscript>2</Subscript> over TiO<Subscript>2</Subscript> based catalysts

At present, carbon dioxide is considered the largest contributor among greenhouse gases. This review covers the current state of problem of carbon dioxide emissions from industrial and combustion processes, the principle of photocatalysis, existing literature related to photocatalytic CO₂ reduction over TiO₂ based catalysts and the effects of important parameters on the process performance including light wavelength and intensity, type of reductant, metal-modified surface, temperature and pressure. Presented at the 34th International Conference of the Slovak Society of Chemical Engineering, Tatranské Matliare, 21–25 May 2007.     

Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

Investigation of miniature CO<Subscript>2</Subscript> gas sensor based on NASICON

A miniature CO₂ gas sensor based on NASICON (sodium super ionic conductor) thick film was fabricated. The solid-electrolyte NASICON material was synthesized through an inorganic-reagent-based sol-gel method. The resulting materials were characterized by means of X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). NASICON paste was coated on a piece of alumina substrate attached to a platinum heater. Li₂CO₃-BaCO₃ binary carbonate in molar ratio 1 : 1.5 was utilized as the sensing electrode. Within a wide range of CO₂ volume ratio concentration from 500 to 5000 ppm, the output electromotive force (EMF) of the sensor followed Nernst equation well at high working temperature. The response and recovery times were 20 and 58 s, respectively. This miniature CO₂ gas sensor possessed extra merits such as low power consumption, miniaturized framework, and easy fabrication.     

Visible-light-driven photocatalytic degradation of microcystin-LR by Bi-doped TiO<Subscript>2</Subscript>

Bi-doped nano-crystalline TiO₂ (Bi–TiO₂) has been synthesized by sonocrystallization at low temperature. The Bi–TiO₂ materials have narrower bandgaps than pristine TiO₂, which endow them with significant visible light absorption. Accordingly, these materials had enhanced photocatalytic activity in the degradation of organic dye pollutants and the cyanotoxin microcystin-LR (MC-LR) under visible irradiation. It was found that degradation of MC-LR is rather efficient. After irradiation with visible light for 12 h the original MC-LR was removed completely, and 78% of the organic carbon was mineralized into CO₂ after irradiation for 20 h. The hydroxyl radical (·OH) is the major active species responsible for the degradation reaction. Identified intermediates primarily originate from attack of ·OH radicals on the double bonds between C4 and C5 (C6 and C7) of Adda and the ethylenic bond of Mdha in MC-LR. Some peptide bonds are also broken with longer irradiation time.