Immobilization of calix[6]arene bearing carboxylic acid and amide groups on aminopropyl silica gel and its sorption properties for Cr(VI)

An aminopropyl silica gel-immobilized calix[6]arene (C[6]APS) containing both amide and acid moieties was prepared from p-tert-butylcalix[6]arene hexacarboxylate derivative and aminopropyl silica gel in the presence of N,N′-diisopropyl carbodiimide coupling reagent. C[6]APS was used to evaluate the sorption properties of Cr(VI) as a sorbent material. In sorption studies, it was observed that C[6]APS was highly effective at pH 1.5 for Cr(VI). The effect of parameters such as pH, sorbent dosage, contact time, initial Cr(VI) concentration and temperature on Cr(VI) sorption; the sorption isotherms were also studied. Maximum sorption capacity was obtained as 3.1 mg g^?1 at pH 1.5 and 25 °C for 1 h and 10.4 mg L^?1 initial Cr(VI) concentration. Thermodynamic parameters such as change in free energy, enthalpy, and entropy were also determined. In the isotherm studies, Langmuir and Freundlich isotherm models were applied and it was found that the experimental data confirmed to Freundlich isotherm model, and the batch sorption capacity of C[6]APS was calculated as 37.66 mg g^?1.     

Preparation of calix[4]arene-based sporopollenin and examination of its dichromate sorption ability

The present study describes the preparation of a new calix[4]arene-based sporopollenin material and its application for the removal of Na₂Cr₂O₇ from aqueous solution. The novel calix[4]arene-based sporopollenin material was prepared via the immobilization of dihydrazine amide derivative of p-tert-butylcalix[4]arene (3) onto the modified sporopollenin. The newly prepared calix[4]arene-based sporopollenin is characterized by using different analytical techniques such as FT-IR spectroscopy, scanning electron microscope and Elemental analysis. The batch wise sorption study was carried out to optimize various experimental parameters such as the effect of sorbent dosage, pH, temperature and Cr(VI) anion concentration. It has been found that the sorption of Cr(VI) anion on calix[4]arene-based sporopollenin was highly pH dependent and maximum sorption was achieved at pH 1.5. The sorption behavior was also evaluated by Langmuir, Freundlich and Dubinin Radushkevich isotherms. The value of correlation coefficient (R ²) showed a good agreement with Freundlich isotherm model. Result of study demonstrated that calix[4]arene-based sporopollenin proved to be highly effective for the removal of Cr(VI).     

杯芳烃接枝超细SiO2的制备及其对Cu2+、Ag+萃取性能的研究

通过对杯[4]芳烃以及杯[6]芳烃上缘进行烯丙基化和硅氢加成2步衍生化反应得到硅氢化杯[4]芳烃以及硅氢化杯[6]芳烃,再将这2种硅氢化杯芳烃衍生物分别接枝到超细SiO₂上。在不同的pH值条件下,就2种杯芳烃接枝超细SiO₂衍生物对水合Cu²⁺及Ag⁺的萃取性能进行了研究。结果表明,与对叔丁基杯芳烃相比较,杯芳烃接枝超细SiO₂衍生物对Cu²⁺和Ag⁺的萃取率都有所提高,其中杯[4]芳烃接枝超细SiO₂对Ag⁺的最高萃取率达到98.78%,杯[6]芳烃接枝超细SiO₂对Cu²⁺的最高萃取率达到67.74%。     

Extraction properties of 25,27-bis(carbonylmethoxy)calix[4]arenes towards Sr2+: competitive extraction and extraction in a synthetic groundwater

The Sr²⁺ extraction properties of some 25,27-bis(carbonylmethoxy)calix[4]arenes, in which ester (–CH₂CO₂Et), keto (–CH₂COCH₃) and acid functionalities (–CH₂CO₂H) have been attached to the lower rim, are reported. Strontium ion extraction experiments were performed in a chloroform/water system, and the extraction performance analyzed by radiotracing using the short-lived radio nuclide ⁸⁵Sr. Effects of pH value, ligand to metal ratio, temperature, extraction time and strontium species on the extraction behavior were examined. It was observed that the 25,27-bis(carboxymethoxy)calix[4]arene derivatives are potent extracting agents towards the strontium ion, showing remarkable extraction performance in competition with a series of organic and inorganic impurities and in a synthetic groundwater. The crystal structure of 25,27-bis(acetonyloxy)calix[4]arene is also reported.     

Synthesis and extraction studies of polymeric phthalimido functionalized calix[4]arene

The article comprises synthesis and extraction studies of polymeric calix[4]arene having phthalimide groups at the lower rim. The polymeric phthalimido functionalized calix[4]arene was synthesized via radical initiated reactions involving a vinylic monomer 5,11,17,23-tetra-tert-butyl-25-[4-(acrylamido)benzyloxy]-26,28-bis-(2-phthalimido-ethoxy)-27-hydroxycalix[4]arene (5) with styrene. A five atom spacer group was incorporated between the bulky calixarene core and the acrylate moiety in order to minimize steric interactions which proved to impede the polymerization. From the liquid–liquid and solid–liquid extraction studies it has been concluded that the precursor 3 (5,11,17,23-tetra-tert-butyl-25-(4-nitro benzyloxy)-26,28-bis-(3-phthalimidoethoxy)-27-hydroxy-calix[4]arene) is selective for metal cations. The order of extractability of metal cations by the ligand 3 decreases in the sequence: Hg²⁺ > Cd²⁺ > Cu²⁺ > K⁺ > Co²⁺ whereas its polymeric derivative is selective in the sequence: Hg²⁺ > Cd²⁺ > K⁺ > Co²⁺ > Cu²⁺ for the metal cations used in the experiments.     

Determination of Tryptophan using a p-Sulfonated Calix [4,6,8]arene Modified Gold Electrode

The ability of p-sulfonated calix[n]arenes (n = 4, 6, 8) to form complexes with tryptophan was studied. The electrochemical properties of these complexes immobilized on gold surfaces were examined by cyclic voltammetry. Parameters affecting the performance of the modified electrodes including the arene concentration, scan rate, applied potential, and pH were optimized. Under the optimal conditions, the method had a linear response to tryptophan between 1 × 10^?7 M and 1 × 10^?5 M with a detection limit of 3 × 10^?8 M. The interaction of the tryptophan–p-sulfonated calix[4]arene complex was more stable than the tryptophan–p-sulfonated calix[6]arene and p-sulfonated calix[8]arene complexes. Molecular modeling calculations indicated that electrostatic interactions and structural matching effects were predominant stabilizing factors. The modified electrodes demonstrated good reproducibility and high selectivity, illustrating their effectiveness for analytical measurements.     

Carrier‐Mediated Transport of Hg(II) through Bulk and Supported Liquid Membranes

The transport of Hg (II) ions from an aqueous solution into an aqueous receiving solution through bulk and supported liquid membranes containing a calix[4]arene derivative 1 as a carrier was examined. The kinetic parameters of bulk liquid membrane studies were analyzed assuming two consecutive, irreversible first‐order reactions. The influence of temperature, stirring rate, carrier concentration and solvent on the kinetic parameters (k₁, k₂, R_m ^max, t_max, J_d ^max, J_a ^max) has also been investigated. The membrane entrance rate, k₁, and the membrane exit rate, k₂, increased with increasing temperature and stirring rate. The activation energy values are calculated as 4.87 and 48.63 kj mol^?1 for extraction and reextraction, respectively. The values of calculated activation energy indicate that the process is diffusionally controlled by species. Also, the transport behavior of Hg²⁺ from aqueous solution through a flat‐sheet supported liquid membrane has been investigated by the use of calix[4]arene derivative 1 as carrier and Celgard 2500 as the solid support. A Danesi mass transfer model was used to calculate the permeability coefficients for each parameter studied. The highest values of permeability were obtained with 2‐nitrophenyloctyl‐ether (NPOE) solvent and the influence was found to be in the order of NPOE>chloroform>xylene.     

Sorption of Cu(II) onto silica gel immobilized calix[4]arene derivative with tripodal structure

This study contains the synthesis of silica gel-immobilized calix[4]arene derivative (TR-CL[4]P) as a new sorbent and its sorption studies towards Cu (II) ion in aqueous solution. The aldehyde pointed calix[4]arene derivative 5 was synthesized and then it was immobilized onto 3-aminopropilsilica gel (APS). In batch sorption experiments, the experimental results showed that TR-CL[4]P is effective sorbent towards Cu (II) ion. Therefore, the effect of solution pH, sorption time, temperature and initial metal ion concentration onto Cu (II) sorption was investigated. Maximum Cu(II) removal was obtained at 30?°C, 30?min and pH 6.0 for TR-CL[4]P and the batch sorption capacity was found as 17.8?mg/g. The characteristics of the sorption process for Cu (II) ion were evaluated by using the Langmuir, Freundlich and Dubinin–Radushkevich (D–R) adsorption isotherms. Also, thermodynamic parameters, i.e., ΔG, ΔS, and ΔH were calculated for the system.     

Scavenging of UO2 2+ using 4-sulfonic calix[6]arene in the presence of goethite

The scavenging of UO₂ ²⁺ using 4-sulfonic calix[6]arene in the presence of a strong adsorbent was studied as a function of pH. The adsorbent selected was goethite because of its strong affinity for UO₂ ²⁺ and its abundance in natural soils. In order to understand the underlying chemistry of the scavenging process, the adsorption of UO₂ ²⁺ and 4-sulfonic calix[6]arene onto goethite, respectively, and the extraction of adsorbed UO₂ ²⁺ from goethite surface were modeled using the triple-layer model. The model well explained the pH dependence of the adsorption and extraction processes. This work showed that maximum extraction was obtained around pH 10.5 in the presence of 12g/l goethite in the case of a 1:3T _U(VI):T _calixareneratio.     

Flip–flop Motion of Circular Hydrogen Bond Array in Thiacalix[4]arene

Thiacalix[4]arene contains a circular array of four equivalent hydrogen bonds on its lower rim. The array undergoes a flip–flop motion between two possible directions. The rate of this motion in the temperature range 223–313 K is assessed by means of measurements of the nuclear spin relaxation. The values of the activation enthalpy (38.7 kJ mol^? 1) and of the activation entropy ( ? 15 J mol^? 1 K^? 1) were determined. In addition, correlation times of molecular tumbling have been determined in the same temperature range. The measured properties of thiacalix[4]arene are compared to those of the “classical” calix[4]arene in order to utilize them for fine tuning of the building blocks in supramolecular chemistry.     

Preparation of 4-sulfonylcalix[6]arene modified Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> as adsorbent for adsorption of U(VI) from aqueous solution

The 4-sulfonylcalix[6]arene modified Fe₃O₄ (MFS) was characterized by FT-IR, SEM, VSM, TGA, etc., which showed that its saturation magnetization was 64.99 emu g^?1 with the particle size 10–40 nm. The maximum adsorption efficiency by MFS for 2.5 mg L^?1 U(VI) solution amounted to 94.39%, which was higher than that by Fe₃O₄ (65.22%) under its optimum adsorption conditions. The adsorption of MFS and Fe₃O₄ were both followed the pseudo-second order model and the Langmuir isotherm model. The Gibbs free energy change and enthalpy change revealed that the adsorption of U(VI) by MFS was a spontaneous and endothermic process.     

Extraction of uranium and transuranium elements with <Emphasis Type="Italic">tert</Emphasis>-butylthiacalix[4]arene from carbonate-alkaline solutions

Extraction efficiency of uranium and transuranium elements (Np, Pu, Am and Cm) with tert-butylthiacalix[4]arene TCA from carbonate-alkaline solutions is studied and compared with that of europium (III). Plutonium (III, IV) extraction efficiency with TCA is found to be lower comparing with that of trivalent americium and europium. Extraction efficiency of studied radionuclides decreases as following: Am ? Eu ? Pu (III), U(VI), Np (V) > Pu (IV) at pH 12. Carbonate concentration increase in aqueous phase suppresses significantly extraction of all studied radionuclides, except americium. This condition can be used for americium individual recovery from complex radioactive carbonate-alkaline solutions.     

Interaction of U(VI) with Na-attapulgite in the presence and absence of humic acid as a function of pH, ionic strength and temperature

The interaction of U(VI) with Na-attapulgite was studied by using batch technique at different experimental conditions. The effect of contact time, solid content, pH, ionic strength and temperature on the sorption of U(VI) onto Na-attapulgite in the presence and absence of humic acid was also investigated. The results showed that the sorption of U(VI) on Na-attapulgite achieved sorption equilibrium quickly. Sorption of U(VI) on Na-attapulgite increased quickly with increasing pH at pH < 6.5, and then decreased with pH increasing at pH > 6.5. The sorption curves were shifted to left in low NaClO₄ solutions as compared those in high NaClO₄ solutions. The sorption was strongly dependent on pH and ionic strength. The sorption was dominated by ion exchange or outer-sphere surface complexation at low pH values, and by inner-sphere surface complexation or surface precipitation at high pH values. The thermodynamic parameters (i.e., ΔH ⁰, ΔS ⁰, and ΔG ⁰) for the sorption of U(VI) were calculated from the temperature dependent sorption isotherms, and the results suggested that the sorption reaction was an endothermic and spontaneous process. The Na-attapulgite is a suitable material in the removal and preconcentration of U(VI) from large volumes of aqueous solutions in nuclear waste management.     

The inhibitory properties of acidic functionalised calix[4]arenes on human papillomavirus pentamer formation

ABSTRACT

Human Papillomavirus (HPV) is the leading cause of cervical cancer, with only some HPV types prevented with vaccines and no treatments for the viral infection itself. One way to target viral infection is by inhibiting the assembly of the L1 monomer into a pentamer, which forms the viral capsid. Four calix[4]arene compounds functionalised with D- and L-aspartic and glutamic acid and an iminodiacetic functionalised calix[4]arene were synthesised and tested for L1 pentamer formation inhibition. The amino acid functionalised calix[4]arene derivatives showed millimolar inhibition (IC₅₀ = 0.72 to 2.67 mM) of pentamer formation, with little difference between the stereoisomers. The iminodiacetic acid calix[4]arene derivative showed no inhibitory properties, despite sharing structural similarities with the four other calix[4]arenes. Confirmation of binding the negatively charged compounds to the positive residues of the L1 protein was achieved by trypsin digestion. This study is helpful in the development of cost-effective inhibitors to prevent HPV assembly.     

Determination of 90Sr in environmental samples using solid phase extraction chromatography

The p-tert-butyl calix[4]arene thiophenol derivative was successfully synthesized with reflux condition and was characterized by FT-IR and ¹H-NMR. This work mainly adopted the method of controlling variables. The results showed that the optimum pH value, temperature and extraction time were respectively 4.5, 25 °C and 90 min. By calculating the data of the enthalpy change and gibbs free energy, indicating that the process of reaction was an exothermic and spontaneous process, and it demonstrated a close agreement with pseudo-second-order kinetic model. It is also found that the coexisting cations on the extraction of uranium had greater influence.

     

Removal of Chromium Anions with Nanofiltration-Complexation by Using p-Sulfonated Calix[4]arene

This article describes the removal of chromium anions from aqueous solutions by using nanofiltration-complexation consisting of pilot-scale nanofiltration equipment (Osmonics Sepa CF Membrane Cell) and water-soluble p-sulfonated calix[4]arene ligand. For the determination of optimum removal conditions of the chromium anions, the effect of pH, ligand cavity size, and foreign anions on the retention of the chromium anions in nanofiltration-complexation system was also evaluated. The results showed that water-soluble p-sulfonated calix[4]arene was an effective and selective ligand for the chromium anions over Cl^? , SO₄ ^2 ?  and NO₃ ^?  anions in nanofiltration-complexation system at pH 9.4.     

Proparacaine complexation with β‐cyclodextrin and p‐sulfonic acid calix[6]arene,as evaluated by varied 1H‐NMR approaches

This study focused on the use of NMR techniques as a tool for the investigation of complex formation between proparacaine and cyclodextrins (CDs) or p‐sulfonic acid calix[6]arene. The pH dependence of the complexation of proparacaine with β‐CD and p‐sulfonic acid calix[6]arene was studied and binding constants were determined by ¹H NMR spectroscopy [diffusion‐ordered spectroscopy (DOSY)] for the charged and uncharged forms of the local anesthetic in β‐CD and p‐sulfonic acid calix[6]arene. The stoichiometries of the complexes was determined and rotating frame Overhauser enhancement spectroscopy (ROESY) 1D experiments revealed details of the molecular insertion of proparacaine into the β‐CD and p‐sulfonic acid calix[6]arene cavities. The results unambiguously demonstrate that pH is an important factor for the development of supramolecular architectures based on β‐CD and p‐sulfonic acid calix[6]arene as the host molecules. Such host–guest complexes were investigated in view of their potential use as new therapeutic formulations, designed to increase the bioavailability and/or to decrease the systemic toxicity of proparacaine in anesthesia procedures. Copyright © 2009 John Wiley & Sons, Ltd.     

Effect of the glutaraldehyde derivatives of Calix[n]arene as cross-linker reagents on lipase immobilization

Synthesis of the glutaraldehyde derivatives calix[n]arene (n = 4,6,8) (Calix[n]-GA) and using as cross-linkers for immobilization of Candida rugosa lipase (CRL) have been discussed in this paper. The amino functional calix[n]arene derivatives (Calix[n]-NH ₂) were synthesized via reduction of dinitrile, hexanitrile and octanitrile derivatives of calix[n]arenes. These amino functional calix[n]arene derivatives (Calix[n]-NH ₂) were converted to their aldehyde derivativatives with glutaraldehyde. The calix[n]arene derivatives were used in lipase immobilization in order to see the role of calix[n]arene binding site on the lipase activitiy and stability. The activity recovery of calix[n]arene-supported lipases (Calix[n]-CRL) based on the Calix[4]-CRL, Calix[6]-CRL and Calix[8]-CRL reaches to 53.5, 66.1 and 76.4%, respectively.     

Interaction of water-soluble calix[4]arene with l-tryptophan studied by fluorescence spectroscopy

The complexing ability of water-soluble calix[4]arene for l-tryptophan (l-try) was investigated by a variety of techniques. The spectrofluorometry titrations were performed at different temperatures to determine stability constants, as well as to evaluate the thermodynamic parameters of the obtained complex. The effect of pH on the complexation process was quantitatively assessed. Moreover, to obtain information about the binding mechanism of the interaction, ¹H NMR studies were carried out. Molecular modeling showed that water-soluble calix[4]arene accommodated part of l-amino acid in its cavity meanwhile the aliphatic chain of l-tryptophan stuck out of the cavity. Based on the experiment data, the association process of complexes was established. The water-soluble calix[4]arene was found to be able to adjust its conformation to fit the size of aromatic l-tryptophan, and the benzene ring of amino acid penetrated into the hydrophobic cavity of calix[4]arene.     

单氧代-二硒烷基-1, w-二氧取代杯[4]衍生物的合成,结构及萃取性能研究

Novel macrocyclic monooxa-diselkylene-1,ω-dioxy substituted calix[4]arene derivatives 1a-5a were synthesized by the reaction of calix[4]arene dibromides 1-5 with the disodium salt of bis（2-selenylethyl）ether in the yields between 28% and 64%. Their structures were characterized by proton and carbon NMR spectra. X-Ray structure analysis of la further confirmed the cone conformation of compounds 1a-5a. An interesting host-guest complex of la with dichloromethane via CH/π and C1/π interactions was elucidated. Extraction experiments showed that these novel monooxa-diselkylene-1,ω-dioxy substituted calix[4]arene derivatives 1a-5a had strong extraction ability towards mercury ion. The interaction of Hg^2＋with the calix ligand has also been investigated by 1^H NMR titration.