Synthesis and characterization of Pr<Superscript>3+</Superscript>-doped glass scintillators prepared by the sol–gel method

Transparent and crack-free Pr-doped silica glass scintillators were successfully synthesized using the sol–gel method. A peak found at 301 nm in the photoluminescence spectrum was ascribed to a radiative transition of the Pr³⁺ emission center. The associated excitation peak was located at 276 nm. The energy of the excitation peak (4.50 eV) was significantly lower than the energy gap (5.83 eV) of the ¹S₀ to ³H₄ f–f transition. Therefore, the f–f transition was excluded as the origin, and the transition was attributed to 5d–4f. In the absorption spectrum, several bands of the f–f transition were observed. Fourier transform infrared spectroscopy was employed to understand the microstructural features and OH group concentration in the Pr³⁺-doped silica glass. It was revealed that a Si–O network had been successfully formed, and that the OH group concentration decreased with increasing thermal treatment temperature reaching a saturation value for temperatures higher than 750 °C. The absence of praseodymium oxide nanocrystalline clusters was confirmed by transmission electron microscopy (TEM), even in the sample with the highest Pr ion concentration. Scintillation properties of the Pr³⁺-doped silica glass were also characterized. The scintillation decay time constants were estimated to be approximately 1.3 and 14 ns, which supports the assignment of the luminescence to the 5d–4f transition. The scintillation light yield of the Pr³⁺-doped silica glass was estimated to be approximately 130 photons/MeV.     

Synthesis and characterization of tellurium-doped CdO nanoparticles thin films by sol–gel method

In this work, tellurium (Te) doped CdO nanoparticles thin films with different Te concentrations (1, 3, 5, 7 and 10 %) were prepared by sol–gel method. The effects of Te doping on the structural, morphological and optical properties of the CdO thin films were systematically studied. From X-ray diffraction spectra, it has seen that all of thin films were formed polycrystalline and cubic structure having (111), (200) and (311) orientations. The structure of CdO thin films with Te-dopant was formed the unstable CdTeO₃ monoclinic structure crystal plane ( $ {\bar{\text{1}}\text{22}} $ 1 ¯ 22 ), however, the intensity of this unstable peak of the crystalline phase decreased with the increase of Te-doping ratio. The strain in the structure is also studied by using Williamson-Hall method. From FE-SEM images, it has seen that particles have homogeneously distributed and well hold onto the substrate surface. Additionally, grain size increases from 27 to 121 nm with the increase of Te-doping ratio. Optical results indicate that 1 % Te-doped CdO thin film has the maximum transmittance of about 87 %, and the values of optical energy band gap increases from 2.50 to 2.64 eV with the increase of Te-doping ratio. These results make Te-doped CdO thin films an attractive candidate for thin film material applications.     

Synthesis and characterization of nitrogen-doped TiO2 nanoparticles prepared by sol–gel method

The N-doped TiO₂ has been synthesized by sol?Cgel method, using titanium isopropoxide, isopropanol and an aqueous solution of ammonia with ratio 2:1:10. The concentrations used for the NH₃ aqueous solution were 3, 7, 10 and 15?%. The samples have been analysed by X-ray diffraction, electron microscopy (SEM and TEM) thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), micro-Raman spectroscopy and diffuse reflectivity. TEM, SEM, DSC and TGA showed that the morphology is influenced by the presence of N^3? ions but not by the concentration of the solution. Instead reflectance gave us a relation between values of the energy gap and the concentration of N^3? ions: the gap between valence and conduction band lowers as the concentration of NH₃ in the starting solution increases. From these results we can say that the properties of the material have been tuned by doping with nitrogen ions because the particles absorb more light in the visible range, and this is important for photovoltaic and photocatalytic applications.     

Luminescence and long-lasting afterglow in Mn<Superscript>2+</Superscript> and Eu<Superscript>3+</Superscript> co-doped ZnO–GeO<Subscript>2</Subscript> glasses and glass ceramics prepared by sol–gel method

To develop new fluorescent and afterglow materials, Mn²⁺ and Eu³⁺ co-doped ZnO–GeO₂ glasses and glass ceramics were prepared by a sol–gel method and their optical properties were investigated by measuring luminescence, excitation and afterglow spectra, and luminescence quantum yield (QY). Under UV irradiation at 254 nm, some glasses and all of the glass ceramics showed green luminescence peaking at 534 nm due to the ⁴T₁ → ⁶A₁ transition of tetrahedrally coordinated Mn²⁺ ions. The strongest luminescence was observed in a glass ceramic of 0.1MnO–0.3Eu₂O₃–25ZnO–75GeO₂ heat treated at 900 °C, with QY of 49.8%. All of the green-luminescent glasses and glass ceramics showed green afterglow, and the afterglow lasting for more than 60 min was obtained in a glass ceramic heat treated at 900 °C. It is considered that the Eu³⁺ ions may behave as electron trapping centers to be associated with the occurrence of the green afterglow due to the Mn²⁺ ions in the co-doped system.     

Colour tuneability and white light generation in Yb<Superscript>3+</Superscript>–Ho<Superscript>3+</Superscript>–Tm<Superscript>3+</Superscript> co-doped SiO<Subscript>2</Subscript>–LaF<Subscript>3</Subscript> nano-glass-ceramics prepared by sol–gel method

Nanostructured transparent glass-ceramics with composition of 95SiO₂–5LaF₃ co-doped with 0.3Yb³⁺, 0.1Ho³⁺ and 0.1Tm³⁺ (mol%) were synthesized by thermal treatment of precursor sol–gel derived glasses. X-ray diffraction and transmission electron microscopy analysis point out the precipitation of hexagonal LaF₃ nanocrystals with diameter ranging from 11 to 20 nm in these nano-glass-ceramics. White light generation by means of efficient blue, green and red up-conversion luminescence under infrared excitation at 980 nm was observed and involved mechanisms were analyzed. Colour tuneability is achieved by varying the up-conversion emission ratios as a function of pump power.     

Synthesis of fluorine doped tin oxide nanoparticles by sol–gel technique and their characterization

This article presents novel attempt to synthesis of fluorine doped tin oxide (FTO) nanoparticles by sol–gel technique. The synthesized FTO nanoparticles were obtained after calcination. Temperatures of calcination were 600 and 700 °C due to identify changes in the particles size growth. A DG/DTA and FTIR study identifies the oxide and formation of the nanopowders. The XRD studies confirm the tetragonal crystallite structure of fluorine doped tin oxide. The TEM image confirms the size of FTO particles in nanoscale. The electrical studies on FTO nanopowders results the decrease in resistivity profile with increasing calcinations. The optical band gap studies for sol–gel synthesis FTO nanoparticles is found to be in the range of 4.11–3.84 eV conforming decreasing optical band gap with increasing calcinating temperatures.     

Photoluminescence and photocatalytic properties of Er<Superscript>3+</Superscript>-doped In<Subscript>2</Subscript>O<Subscript>3</Subscript> thin films prepared by sol–gel: application to Rhodamine B degradation under solar light

The effect of Er³⁺ doping (1%) on the structural, optical and photocatalytic properties of In₂O₃ thin films deposited on quartz substrates by spin coating was investigated. The In₂O₃:1% Er³⁺ films, annealed in the temperature range 800–1000 °C, were characterized by X-ray diffraction, scanning electron microscopy (SEM), atomic force microscopy, UV–Vis spectroscopy, ellipsometry and photoluminescence (PL). The films are polycrystalline with a cubic structure and the lattice parameter increases with the incorporation of Er³⁺ owing to its larger radius. The SEM images of the film show a granular morphology with large grains (~ 200 nm). The doped In₂O₃ film exhibits less transparency than In₂O₃ in the UV–visible region with band gaps of 3.42 and 3.60 eV, respectively. PL shows strong lines at 548 and 567 nm, assigned to Er³⁺ under direct excitation at 532 nm. The energy diagram of the junction In₂O₃:1% Er³⁺/Na₂SO₄ (0.1 M) solution plotted from physical and photoelectrochemical characterizations shows the feasibility of the films for Rhodamine B (RhB) degradation under solar light. The conduction band at 2.22 V deriving from the In³⁺:5s orbital is suitably positioned with respect to the O₂/O ₂ ^· level (~ 1.40 V_SCE), leading to oxidation of 32% of 10 ppm RhB within 40 min of solar irradiation.     

Strong visible up-conversion emissions and thermometric applications of Er<Superscript>3+</Superscript>–Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> prepared by the sol–gel method

The Er³⁺–Yb³⁺ codoped Al₂O₃ has been prepared by the sol–gel method using the aluminium isopropoxide [Al(OC₃H₇)₃]-derived Al₂O₃ sols with addition of the erbium nitrate [Er(NO₃)₃ · 5H₂O] and ytterbium nitrate [Yb(NO₃)₃ · 5H₂O]. The phase structure, including only two crystalline types of doped Al₂O₃ phases, θ and γ, was obtained for the 1 mol% Er³⁺ and 5 mol% Yb³⁺ codoped Al₂O₃ at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300–825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er³⁺–Yb³⁺ codoped Al₂O₃ plays an important role in the application of high temperature sensor.     

Structural and optical characterization of Zn doped TiO<Subscript>2</Subscript> nanoparticles prepared by sol–gel method

Undoped and zinc-doped TiO₂ nanoparticles (Ti_1−xZn_xO₂ where x = 0.00–0.10) were synthesized by a sol–gel method. The synthesized products were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM) and UV–VIS spectrometer. XRD pattern confirmed the tetragonal structure of synthesized samples. Average grain size was determined from X-ray line broadening using the Debye–Scherrer relation. The crystallite size was varied from 10 to 40 nm as the calcination temperature was increased from 350 to 800 °C. The incorporation of 3–5 mol% Zn²⁺ in place of the Ti⁴⁺ provoked a slight decrease in the size of nanocrystals as compared to undoped TiO₂. The SEM and TEM micrographs revealed the agglomerated spherical-like morphology with a diameter of about 10–30 nm and length of several nanometers, which is in agreement with XRD results. Optical absorption measurements indicated a blue shift in the absorption band edge upon 3–5 mol% zinc doping. Direct allowed band gap of undoped and Zn-doped TiO₂ nanoparticles measured by UV–VIS spectrometer were 2.95 and 3.00 eV at 550 °C, respectively.     

Preparation of LiTaO<Subscript>3</Subscript> nanoparticles by a sol–gel route

A sol–gel route was developed to prepare pure ultrafine LiTaO₃ powders using Ta₂O₅, Li₂CO₃, citric acid (CA) as chelating agent, ethylene glycol (EG) as esterification agent and polyethylene glycol (PEG) as dispersant. The effects of pH value and heat treatment temperature of powder precursor on the synthesis of LiTaO₃ powders were investigated. The phase content and morphology of the final product were evaluated by XRD, SEM and TEM. A transparent gel was produced when heating a mixed-solution of CA, EG, Li and Ta ions with a molar ratio of [CA]:[EG]:[Li]:[Ta] = 3.0:6.0:1.0:1.0 and 2‰ PEG additions with a pH value of 7 at water bath temperature of 80 °C. The results showed that single phase LiTaO₃ powders with average particle sizes of nanometers were produced after heat treatment of the powder precursor at 650, 700, 800, and 900 °C respectively for 2 h.     

IR Luminescence of Nd<Superscript>3+</Superscript>, Sm<Superscript>3+</Superscript>, and Yb<Superscript>3+</Superscript> β-Diketonates in Different Aggregate States

The influence of the aggregate state on the IR luminescence is studied for the Nd(III), Sm(III), and Yb(III) complexes with the thienyl, phenyl, and alkyl derivatives of acetylacetone in solutions and as sorbates on the polymer matrix. It is found that the luminescence intensity of the sorbates of the complexes is 2–3 orders of magnitude higher than that in solutions due to the elimination of diffusion and respective intermolecular nonradiative losses of the excitation energy.     

Synthesis of CeO<Subscript>2</Subscript> or α–Mn<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles via sol–gel process and their optical properties

Nanocrystalline cubic fluorite/bixbyite CeO₂ or α–Mn₂O₃ has been successfully synthesized by using methanol as a solvent via sol–gel method calcined at 400 °C. The obtained products were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), Transmission electron microscopy (TEM), UV–vis absorption and Photoluminescence (PL) spectroscopy. TEM reveals that the as-synthesized ultra-fine samples consist of elliptical/spherical and sheet-like morphology of crystalline particles of 8/30 nm, which are weakly aggregated. Optical absorbance spectra reveal that the absorption of ceria in the UV region originates from the charge- transfer transition between the O²⁻ (2p) and Ce⁴⁺ (4f) orbit in CeO₂. However, α–Mn₂O₃ nanostructures with nearly pure band gap emission should be of importance for their applications as UV emitters.     

Synthesis and characterization of TiO<Subscript>2</Subscript> doping with rare earths by sol–gel method: photocatalytic activity for phenol degradation

The enhancement of TiO₂ photocatalyst activity will lead to more practical applications of this technology. In this work we studied the effect of rare earth doping of sol–gel synthesized TiO₂ for phenol degradation and we compared the performance with commercial catalyst. Photocatalysts were characterized by nitrogen adsorption to determine textural properties, ultraviolet visible light diffuse reflectance spectrometry (UV-Vis DRS), X-ray diffraction, STEM-EDS (scanning transmission electronic microscopy-energy dispersive X-ray spectroscopy) and XPS (X-ray photoelectron spectroscopy). Main phase for materials calcined at 500 °C was anatase. Residual nitrogen from NH₄OH used in the sol–gel synthesis was identified by XPS analysis. Ti³⁺/Ti⁴⁺ ratio increased when TiO₂ was doped with 0.5 wt% of Ce. Anatase phase was stabilized in photocatalysts doped with La even after calcination at 800 °C, for Pr and Nd a mixture of anatase-rutile phases was obtained, whereas for Ce doping only rutile phase was found. For the photocatalytic oxidation of phenol, the best results were obtained for Ce doped TiO₂, which could be related to the ability of Ce^IV/Ce^III oxidation/reduction cycle.     

Synthesis of a dysprosium aluminum garnet nanopowder via sol–gel method

A dysprosium aluminum garnet (DAG) nanopowder was synthesized by aqueous sol–gel method using Al powder, HCl and Dy(CH₃COO)₃·4H₂O as raw materials. The dried amorphous gel was heat treated in the range of 800–1,200 °C. The influence of heat treatment on crystallization and phase transformation of the dried gel was investigated using X-ray diffractometery, scanning electron microscopy, thermogravimetry and differential thermal analysis and Fourier transform infrared spectroscopy. It was shown that the gel calcined from 900 to 1,200 °C resulted in the formation of a crystalline DAG nanopowder with particle size distribution ranges from 26 to 98 nm.     

Synthesis and characterization of lead oxide nano-powders by sol–gel method

Our goal in this research was to obtain lead oxide nano-powders by sol–gel method. In this method, lead oxide nano-powders were synthesized through the reaction of citric acid (C₆H₇O₈·H₂O) solution and lead acetate [Pb(C₂H₃O₂)₂] solution as stabilizer and precursor, respectively. The effect of different parameters including calcination temperature, (molar ratio of citric acid to lead acetate) and drying conditions were investigated. The prepared lead oxide nano-powders were characterized by FT-IR spectroscopy, X-ray diffraction, thermogravimetric analysis and scanning electron microscopy. The prepared PbO samples consist of the particles in the range of 50–120 nm or the thick plate like structures with thickness of 53 nm depending on the drying conditions.     

Synthesis and characterization of nanocrystalline tin oxide by sol–gel method

Nanocrystalline SnO₂ particles have been synthesized by a sol–gel method from the very simple starting material granulated tin. The synthesis leads a sol–gel process when citric acid is introduced in the solution obtained by dissolving granulated tin in HNO₃. Citric acid has a great effect on stabilizing the precursor solution, and slows down the hydrolysis and condensation processes. The obtained SnO₂ particles range from 2.8 to 5.1 nm in size and 289–143 m² g⁻¹ in specific surface area when the gel is heat treated at different temperatures. The particles show a lattice expansion with the reduction in particle size. With the absence of citric acid, the precursor hydrolyzes and condenses in an uncontrollable manner and the obtained SnO₂ nanocrystallites are comparatively larger in size and broader in size distribution. The nanocrystallites have been characterized by means of TG-DSC, FT-IR, XRD, BET and TEM.     

Synthesis and characterization of nanostructured aluminum borate by sol–gel method

Nanostructured aluminum borate was synthesized using sol?Cgel technique. X-ray diffraction study revealed that the synthesized aluminum borate was single crystal. These nanorods have very uniform diameter. High-resolution transmission electron microscope images indicate that aluminum borate is well crystallized. The alternating current (AC) conductivity of the aluminum borate was studied as a function of temperature and frequency. The AC conductivity mechanism of the aluminum borate was found to be proportional to ??^s. The exponent s is almost independent with temperature. This suggests that AC conductivity mechanism of the aluminum borate can be interpreted by localized hopping model.     

Different morphologies of ZnO nanostructures via polymeric complex sol–gel method: synthesis and characterization

Various morphologies of ZnO nanostructures, such as nanoparticles, nanorods and nanoflowers have been achieved controllably by polymeric sol–gel method. In this approach, zinc nitrate Zn(NO₃)₂·6H₂O, citric acid and ethylene glycol were used as the source of Zn²⁺, the chelating agent and the solvent agent, respectively. The microstructure of the ZnO nanostructures was characterized by X-ray diffractometry, scanning electron microscopy with the energy dispersive X-ray spectroscopy, transmission electron microscopy, thermogravimetric analysis and Fourier transform infrared spectroscopy. The effect of ethylene glycol to citric acid mole ratio on the morphology and structure of the products was discussed. The ZnO nanoparticles with diameter between 24 ± 2 nm was obtained with EG:CA mole ratio equal to 2:1. The optical properties of as-obtained power were investigated by ultraviolet–visible spectroscopy.