Analysis of polychlorinated dibenzo-p-dioxins, dibenzofurans and dioxin-like polychlorinated biphenyls in vegetable oil samples by gas chromatography-ion trap tandem mass spectrometry

Gas chromatography coupled to ion trap tandem mass spectrometry (CG-MS-MS) has been evaluated for the analysis of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (dl-PCBs) in vegetable oil samples containing different concentration levels (0.2-6 pg WHO-TEQ g(-1) for both PCDD/Fs and dl-PCBs) of the 29 toxic congeners of PCDD/F and dioxin-like PCBs. The effect of potential interfering compounds such as polychlorinated naphthalenes (PCNs), polychlorinated biphenyls (PCBs) and polychlorinated diphenylethers (PCDEs) on the quantification of mono-ortho PCBs has been investigated. In addition, the influence of the clean-up procedure on the final determination by CG-MS-MS was studied, showing that the quality of the results depends to a great extent on this analytical step. Quality parameters have been established and good precisions (CV: 3-19%) and low limits of detection for PCDD/Fs (0.04-0.20 pg g(-1) oil) and dl-PCBs (0.08-0.64 pg g(-1) oil) were obtained. The method was validated by a comparison of the CG-MS-MS results with those obtained by GC-HRMS.     

Validation of the CALUX bioassay for the screening of PCDD/Fs and dioxin-like PCBs in retail fish

The chemical-activated luciferase expression (CALUX) assay is a reporter gene assay that detects dioxin-like compounds based on their ability to activate the aryl hydrocarbon receptor (AhR) and thus expression of the reporter gene. In this paper, the CALUX assay was examined for its application in the screening of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs) and dioxin-like polychlorinated biphenyls (dioxin-like PCBs) in retail fish. The sample extracts were cleaned up on a sulfuric acid-silica gel column followed by an activated carbon column, and the AhR activity of the separated PCDD/F and dioxin-like PCB fractions was determined using the assay. The quantitative limit for 2,3,7,8-tetrachlorodibenzo-p-dioxin (2,3,7,8-TCDD) was 0.98 pg ml(-1) (0.19 pg assay(-1) in the standard curve, corresponding to 0.16 pg g(-1) of CALUX-based toxic equivalency (2,3,7,8-TCDD equivalents) in the tested sample. Recovery tests in which dioxins were added to fish samples resulted in acceptable recoveries (77-117%). The CALUX assay performed well in the analysis of dioxins in fish samples and a comparative study revealed a strong correlation between the CALUX assay and high-resolution gas chromatography-high-resolution mass spectrometry analysis for the determination of PCDD/Fs (r = 0.89) and dioxin-like PCBs (r = 0.91) in retail fish (n = 22). These data revealed that the CALUX assay would be a useful screening method for PCDD/Fs and dioxin-like PCBs in retail fish.     

Selective pressurized liquid extraction of polychlorinated dibenzo-p-dioxins, dibenzofurans and dioxin-like polychlorinated biphenyls from food and feed samples

Selective pressurized liquid extraction (PLE) of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (dl-PCBs) from various food and feed samples was performed with a selective PLE method previously developed for bulk PCBs. The method utilizes sulfuric acid impregnated silica inside the extraction cell to oxidize coextracted fat. Extractions were performed at 100 degrees C with n-heptane for 5 min in two cycles. Data obtained by selective PLE combined with gas chromatography/high-resolution mass spectrometry (GC-HRMS) were compared to concentrations derived from reference laboratories applying conventional sample preparation and GC-HRMS. Experiments performed on spiked vegetable oil, naturally contaminated crude fish oil and oil containing compound feed samples showed good results for these relatively simple matrices. The accuracy was generally +/-20% as compared to spiked levels or to values obtained by the reference laboratories. The precision, measured as the relative standard deviation (RSD) for 2,3,7,8-tetrachlorodibenzo-p-dioxin toxic equivalency values (TEQs), was below 10% in all cases. The method was also tested on naturally contaminated herring tissue, chicken tissue, pork tissue and sepiolitic clay, which all caused some trouble. It was observed that sufficient amounts of sodium sulfate should be used for dehydration of tissue samples and additionally, the cells should not be packed too dense in order to avoid suppressed extraction efficiency. Once this was attended to, satisfactory data could be obtained, except for sepiolithic clay. This study demonstrates that selective PLE can be applied with success to a number of food and feed matrices in analysis of PCDD/Fs and dl-PCBs. Since the fat removal step is on-line, the selective PLE method will reduce time and solvent consumption for sample preparation as compared to traditional clean-up.     

气相色谱/高分辨质谱联用测定环境样品中的二噁英和类二噁英多氯联苯

样品采用索氏抽提,抽提液依次经酸性硅胶床、多段混合硅胶柱和凝胶渗透色谱柱(GPC)净化后,用Florisil硅藻土柱分离出样品中的二噁英(PCDD/Fs)和类二噁英多氯联苯(dioxin-like PCBs),采用同位素稀释法和气相色谱/高分辨质谱联用仪(GC/HRMS)测定了其中的17个2,3,7,8-氯取代二噁英类化合物和12个类二噁英多氯联苯。结果表明,用该法分析二噁英和多氯联苯标准溶液,平行4次的分析结果为:RSD(PCDD/Fs)<8.9%,RSD(PCBs)<11.4%;回收率可达60%-105%。PCDD/Fs和PCBs的检出限分别为0.1-0.8 pg/g和0.05-0.6 pg/g。应用本方法成功测定了沉积物、淤泥、土壤和飞灰中的二噁英和类二噁英多氯联苯,并计算出它们的毒性当量。     

Uncertainty assessment of polychlorinated dibenzo-p-dioxins and dibenzofuran and dioxin-like polychlorinated biphenyl analysis in stationary source sample emissions in accordance with the impending European standard EN-1948 using fly ashes

The analysis of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (dl-PCBs) present in stack gas emissions and solid residues from incinerators will be mandatory in the foreseeable future. European standard EN-1948 is in the process of being updated through the addition of a new Part 4 related to the analysis of the 12 dl-PCBs. Therefore, either a comprehensive and reliable method capable of analyzing all of these 29 compounds (12 dl-PCBs and 17 2,3,7,8-PCDD/Fs) needs to be developed, or the existing PCDD/F analytical procedure must be adapted to include the dl-PCBs. This study has taken the latter approach of modifying PCDD/F methodology and in particular the fractionation step, by isolating dioxins and dl-PCBs into separate fractions ready for high resolution gas chromatography coupled to high resolution mass spectrometry (HRGC/HRMS) analysis. Results obtained from the analysis of Certified Reference Materials (CRM-490 and CRM-615) and fly ashes from the European Committee for Standardization (CEN) intercalibration study demonstrated that the proposed methodology is appropriate to determine the dl-PCBs in accordance with the impending European standard EN-1948. Uncertainty values obtained during the validation of the analytical methodology were 13% total I-TEQ (International Toxic Equivalent) for PCDD/Fs and 31% total WHO-TEQ (World Health Organization Toxic Equivalent) in the case of dl-PCBs. In addition, ‘real’ samples such as emissions and fly ashes were successfully analyzed following the proposed analytical method.     

Triple quadrupole tandem mass spectrometry: A real alternative to high resolution magnetic sector instrument for the analysis of polychlorinated dibenzo-p-dioxins,furans and dioxin-like polychlorinated biphenyls

This paper reports on the optimisation, characterisation, validation and applicability of gas chromatography coupled to triple quadrupole mass spectrometry in its tandem operation mode (GC-QqQ(MS/MS) for the quantification of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs, dioxins) and dioxin-like polychlorinated biphenyls (DL-PCBs) in environmental and food matrices. MS/MS parameters were selected to achieve the high sensitivity and selectivity required for the analysis of this type of compounds and samples. Good repeatability for areas (RSD = 1–10%, for PCDD/Fs and DL-PCBs) and for ion transition ratios (RSD = 0.3–10%, for PCDD/Fs, and 0.2–15%, for DL-PCBs) and low instrumental limits of detection, 0.07–0.75 pg μL⁻¹ (for dioxins) and 0.05–0.63 pg μL⁻¹ (for DL-PCBs), were obtained. A comparative study of the congener specific determination using both GC-QqQ(MS/MS) and gas chromatography-high resolution mass spectrometry (GC-HRMS) was also performed by analysing several fortified samples and certified reference materials (CRMs) with low (feed and foodstuffs), median (sewage sludge) and high (fly ash) toxic equivalency (TEQ) concentration levels, i.e. 0.60, 1.83, 72.9 and 3609 pg WHO-TEQ(PCDD/Fs) g⁻¹. The agreement between the results obtained for the total TEQs (dioxins) on GC-QqQ(MS/MS) and GC-HRMS in all the investigated samples were within the range of ±4%, and that of DL-PCBs at concentration levels of 0.84 pg WHO-TEQs (DL-PCBs) g⁻¹, in the case of feedstuffs, was 0.11%. Both instrumental methods have similar and comparable linearity, precision and accuracy. The GC-QqQ(MS/MS) sensitivity, lower than that of GC-HRMS, is good enough (iLODs in the down to low pg levels) to detect the normal concentrations of these compounds in food and environmental samples. These results make GC-QqQ(MS/MS) suitable for the quantitative analysis of dioxins and DL-PCBs and a real alternative tool to the reference sector HRMS instruments.     

Method development for the analysis of polybrominated diphenyl ethers, polychlorinated biphenyls, polychlorinated dibenzo-p-dioxins and dibenzo-furans in single extract of sediment samples

A comprehensive method was developed for quantitative analysis of polybrominated diphenyl ethers (PBDEs), polychlorinated biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins and dibenzo-furans (PCDD/Fs) in one single extract of environmental samples. The sample preparation procedure included two fractionation steps using silver nitrate silica chromatography to separate PBDEs from PCBs and PCDD/Fs and florisil column to separate PCBs from PCDD/Fs. Acidic silica, acidic alumina and gel permeation chromatography (GPC, for PCBs) or activated carbon column (for PCDD/Fs) were used for further clean-up. The sample extracts were analyzed by using high-resolution gas chromatography/high-resolution mass spectrometry. The entire method was validated from the analysis of mixed standards of PBDEs, PCBs and PCDD/Fs (n = 3); the analysis of certified reference biota (WMF-01). The method was applied for the analysis of 10 sediment samples collected from Haihe River and Dagu Drainage River in Tianjin City. No significant PBDEs pollution was found in the areas.     

GC×GC-ECD: a promising method for the determination of dioxins and dioxin-like PCBs in food and feed

There is a need for cost-efficient alternatives to gas chromatography (GC)–high-resolution mass spectrometry (HRMS) for the analysis of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (PCBs) in food and feed. Comprehensive two-dimensional GC–micro electron capture detection (GC×GC-μECD) was tested and all relevant (according to the World Health Organisation, WHO) PCDD/Fs and PCBs could be separated when using a DB-XLB/LC-50 column combination. Validation tests by two laboratories showed that detectability, repeatability, reproducibility and accuracy of GC×GC-μECD are all statistically consistent with GC-HRMS results. A limit of detection of 0.5 pg WHO PCDD/F tetrachlorodibenzo-p-dioxin equivalency concentration per gram of fish oil was established. The reproducibility was less than 10%, which is below the recommended EU value for reference methods (less than 15%). Injections of vegetable oil extracts spiked with PCBs, polychlorinated naphthalenes and diphenyl ethers at concentrations of 200 ng/g showed no significant impact on the dioxin results, confirming in that way the robustness of the method. The use of GC×GC-μECD as a routine method for food and feed analysis is therefore recommended. However, the data evaluation of low dioxin concentrations is still laborious owing to the need for manual integration. This makes the overall analysis costs higher than those of GC-HRMS. Further developments of software are needed (and expected) to reduce the data evaluation time. Combination of the current method with pressurised liquid extraction with in-cell cleanup will result in further reduction of analysis costs. Electronic supplementary material The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Comparison of gas chromatography-ion-trap tandem mass spectrometry systems for the determination of polychlorinated dibenzo-p-dioxins, dibenzofurans and dioxin-like polychlorinated biphenyls

Two gas chromatography-mass spectrometry systems equipped with an ion-trap mass analyzer working in tandem mode (GC-MS-MS) were evaluated for the determination of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (PCBs) in food samples. The performance of the two ion-trap instruments, which dispose of an external ion source (ThermoFinnigan GCQ/Polaris) and internal ionization (Varian Saturn 2,200), have been compared in terms of linearity, repeatability, limit of detection and long-term precision. Both instruments provided similar run-to-run and day-to-day precisions, ranging from 2% to 8% and between 2% and 13%, and instrumental limits of detection between 0.09 and 0.36 pg injected for PCDD/Fs and from 0.03 to 0.09 pg injected for dioxin-like PCBs. Although both instruments seem to be suitable for food analysis, only the use of external ionization allowed to achieve reliable results for PCDD/F determination at concentrations close to the maximum residue levels established by the EU for foods. Internal ionization provides high limits of detection (from 10- to 30-fold higher) and worse precision (RSD, 14-43%). In contrast, for dioxin-like PCBs both instruments allowed to obtain excellent results with precisions lower than 15%.     

Importance of clean-up for comparison of TEQ-values obtained by CALUX and chemo-analysis

This paper presents Chemically Activated LUciferine gene eXpression (CALUX) TEQ-values obtained for nine plasma samples following two different purification procedures, one of them involving fractionation. CALUX results obtained for the dioxin (DX) and dioxin + PCB (DX + PCB) fractions were then compared to the GC-HRMS TEQ-values calculated for the 17 polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (17 PCDD/F) and 17 PCDD/F + 4 cPCB congeners, respectively. The overestimation of the CALUX (DX fraction) TEQ-values in comparison with the chemo-analyses of the 17 PCDD/F is mainly explained by the presence of other AhR agonists, like brominated compounds. Otherwise, the constancy of the CALUX (DX + PCB fraction) TEQ-value which compares to increasing the GC-HRMS (17 PCDD/F + 4 cPCB) TEQ results raises questions concerning (1) the significance of CALUX results obtained without fractionation as well as (2) the toxicological effect of a cocktail of contaminants on the human health.     

Separation of polychlorinated dibenzo-p-dioxins/furans,non-ortho/mono/di/tri/tetra-ortho-polychlorinated biphenyls,and polybrominated diphenyl ethers groups of compounds prior to their determination with large volume injection gas chromatography—Quadrupole ion storage tandem mass spectrometry

Polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) are important environmental contaminants. Their maximum legally allowable levels in food and environment are in the low pg g⁻¹ range. Therefore some highly selective and sensitive analytical methods must be used to determine them. Prior to final determination by GC/MS the cleaned-up samples have to be split into some fractions in view of large differences in concentrations of various analytes and existence of numerous chromatographic co-elutions (which in any case cannot be fully avoided). The aim of this study was to: (i) develop a robust, time-saving analytical method to isolate, clean-up and fractionate PCBs, PBDEs and PCDD/Fs prior to their determination with gas chromatography/ion trap mass spectrometry; (ii) assess method performance using laboratory validation data and some certified reference materials; (iii) use the developed method to assess PCB/PBDE/PCDD/F levels in samples of commercially available food. A combination of alumina, florisil, modified silica gel and two carbon columns were used for sample cleanup and fractionation. Separate fractions containing dioxins/furans, PBDE, non-ortho, mono-ortho and di-/tri-/tetra-ortho PCBs were obtained. The method statistical parameters were compatible with 1883/2006 EC Regulation (80–120%, RSD below 15%). The method performance was successfully used to evaluation of some real life food samples.     

DR-CALUX((R)) screening of food samples: evaluation of the quantitative approach to measure dioxin, furans and dioxin-like PCBs

European legislation laid down maximum tolerable levels of dioxin in feed and food as well as analytical method requirements. In order to face with large monitoring programs, it was foreseen in the EU strategy to integrate screening methods, using either a qualitative (screening) approach, or a quantitative approach. In this study, dioxin results obtained using the Dioxin Responsive Chemical-Activated LUciferase gene eXpression (DR-CALUX^®) cell-based assay (quantitative approach), were compared with gas chromatography–high resolution mass spectrometry (GC–HRMS) analyses data. Instead of using World Health Organization–toxic equivalent factor (WHO–TEF), the comparison was based on the assessment of relative effective potencies (REPs) for each congener of the 17 toxic 2,3,7,8-polychlorodibenzo-p-dioxins/furans (PCDD/Fs) and 12 dioxin-like polychlorobiphenyls (DL-PCBs). According to published data, DR-CALUX^®-REP evaluated here appear similar to WHO–TEF for PCDD/Fs while lower values were observed for DL-PCBs.

We analyzed two “home made” contaminated fat samples, displaying both the same WHO–toxic equivalent quantities (WHO–TEQ) concentration (12 pg WHO–TEQ g⁻¹). They were spiked with either a low or a high amount of DL-PCBs. In both cases, the DR-CALUX^® measured concentration (picogram 2,3,7,8 tetrachlorodibenzo-p-dioxin (TCDD) eq. g⁻¹) corresponded to the PCDD/Fs WHO–TEQ concentration only. A good agreement was nevertheless found between the DR-CALUX^® measurements and the recalculated DR-CALUX^®-TEQ contents (using DR-CALUX^®-REP instead of WHO–TEF), demonstrating that the observed response was due, in both cases, to the addition of the responses of the standards added to the fat. By contrast, in real contaminated samples (feed or cod liver samples), DR-CALUX^® measured concentrations were similar to WHO–TEQ GC–HRMS measured concentrations. But, depending on the PCDD/Fs and DL-PCBs congener content, the DR-CALUX^® measured concentrations were either lower or higher than calculated DR-CALUX^®-TEQ contents, demonstrating that possible co-extracted contaminants contributed to the CALUX response.

Owing to these divergences, the quantitative determination of dioxin-like content in food and feed using CALUX as screening method is questionable, except for samples displaying constant congener patterns, in which cases, correction factors could be applied.     

Considerations for potency equivalent calculations in the Ah receptor-based CALUX bioassay: normalization of superinduction results for improved sample potency estimation

The chemically activated luciferase expression (CALUX) system is a mechanistically based recombinant luciferase reporter gene cell bioassay used in combination with chemical extraction and clean-up methods for the detection and relative quantitation of 2,3,7,8-tetrachlorodibenzo-p-dioxin and related dioxin-like halogenated aromatic hydrocarbons in a wide variety of sample matrices. While sample extracts containing complex mixtures of chemicals can produce a variety of distinct concentration-dependent luciferase induction responses in CALUX cells, these effects are produced through a common mechanism of action (i.e. the Ah receptor (AhR)) allowing normalization of results and sample potency determination. Here we describe the diversity in CALUX response to PCDD/Fs from sediment and soil extracts and not only report the occurrence of superinduction of the CALUX bioassay, but we describe a mechanistically based approach for normalization of superinduction data that results in a more accurate estimation of the relative potency of such sample extracts.     

Comparison of Three Techniques for Lipid Removal from Seal Blubber: Gel Permeation,Acid Treatment,and Dialysis with Semipermeable Membrane

Abstract

Harbor seal blubber samples were analyzed for PCDD/Fs and PCBs by splitting the initial extract into three aliquots and applying three different techniques for lipid removal (the first step of sample cleanup methodology for GC-HRMS analysis): gel permeation chromatography (GPC), sulfuric acid treatment, and dialysis through semipermeable membrane. Correlation coefficients of analyte concentrations obtained from three sets of replicate samples ranged from 0.965 to 0.994. In addition, a number of seal blubber samples were processed without pre-extraction using only the dialysis technique. The analyte concentrations in these samples correlated well with the analyte concentrations obtained from dialyzed blubber extracts (correlation higher than 0.998). For all analyses (PCDD/Fs, NO- and MO-PCBs) the average surrogate standard recoveries for the GPC and dialysis techniques varied from 68 to 111%. The recoveries for PCDD/Fs and MO-PCBs standards ranged from 61 to 89% and 36 to 43% for the NO-PCBs when the acid treatment technique was used. Dialysis was proven to be an efficient technique for lipid removal of biological samples in comparison with the GPC and acid treatment techniques.     

自动样品前处理在乳品中二恶英和共平面多氯联苯同时测定中的应用

采用索氏提取及自动净化处理系统对乳品进行提取和净化,在高分辨气相色谱-高分辨双聚焦质谱仪(HRGC/HRMS)上进行定性和定量检测。在3种不同残留水平的奶粉样品中,17种多氯代二苯并-对二恶英和多氯代二苯并呋喃（PCDD/Fs）的测定结果与给定值具有很好的一致性,且所有具有保证值的二恶英同系物测定结果的相对标准偏差（RSD）均小于20%;12种共平面多氯联苯（PCBs）测定结果的RSD均在15%以内,内标物的回收率为44%～133%,完全符合国际标准方法的要求。母乳样品的国际考核结果表明本方法在不同实验室间具有良好的准确度和精密度。本方法定量准确可靠,适用于乳品中二恶英及共平面PCBs的同时检测。     

Rapid aryl hydrocarbon receptor based polymerase chain reaction screening assay for polychlorinated dibenzo-p-dioxins and furans in soil and sediment

A method for the estimation of polychlorinated dibenzo-p-dioxin and furan (PCCD/F) toxicity equivalent quotient (TEQ) of soil and sediment matrices is described. The method includes extraction, isolation of the PCDD/Fs from interfering compounds, such as polychlorinated biphenyls (PCBs) and polycyclic aromatic hydrocarbons (PAHs), and measurement of PCDD/F using the PROCEPT aryl hydrocarbon (AhR) receptor based polymerase chain reaction (PCR) assay. The values obtained using the PROCEPT assay correlate well with reference TEQ values generated from gas chromatography-high resolution mass spectrometry (GC-HRMS), with a linearity coefficient (R(2)) of 0.94. Applied in a screening mode at 50pg/g PCDD/F TEQ, the PROCEPT assay yielded five false positive results (2.6%) and no false negative results for 196 analyses of spiked soils and environmental samples obtained from US EPA Superfund sites.     

CALUX measurements: statistical inferences for the dose-response curve

Chemical Activated LUciferase gene eXpression [CALUX] is a reporter gene mammalian cell bioassay used for detection and semi-quantitative analyses of dioxin-like compounds. CALUX dose-response curves for 2,3,7,8-tetrachlorodibenzo-p-dioxin [TCDD] are typically smooth and sigmoidal when the dose is portrayed on a logarithmic scale. Non-linear regression models are used to calibrate the CALUX response versus TCDD standards and to convert the sample response into Bioanalytical EQuivalents (BEQs). Several complications may arise in terms of statistical inference, specifically and most important is the uncertainty assessment of the predicted BEQ. This paper presents the use of linear calibration functions based on Box-Cox transformations to overcome the issue of uncertainty assessment. Main issues being addressed are (i) confidence and prediction intervals for the CALUX response, (ii) confidence and prediction intervals for the predicted BEQ-value, and (iii) detection/estimation capabilities for the sigmoid and linearized models. Statistical comparisons between different calculation methods involving inverse prediction, effective concentration ratios (ECR_20-50-80) and slope ratio were achieved with example datasets in order to provide guidance for optimizing BEQ determinations and expand assay performance with the recombinant mouse hepatoma CALUX cell line H1L6.1c3.     

Evaluation of automated direct sample introduction with comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry for the screening analysis of dioxins in fish oil

An automated direct sample introduction technique coupled to comprehensive two-dimensional gas chromatography-time of flight mass spectrometry (DSI-GC x GC/TOF-MS) was applied for the development of a relatively fast and easy analytical screening method for 17 polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs) and 4 non-ortho polychlorinated biphenyls (PCBs) in fish oil. Comparison of instrumental performance between DSI-GC x GC/TOF-MS and the traditional gas chromatographic high resolution mass spectrometric (GC-HRMS) method showed good agreement of results for standard solutions analyzed in blind fashion. Relatively high tolerance of the DSI technique for lipids in the final extracts enabled a streamlined sample preparation procedure that only required gel permeation chromatography (GPC) and solid-phase extraction (SPE) cleanup with graphitized carbon black. The sample size for the method was 2g of cod liver oil, which achieved limits of quantitation (LOQs) of 0.019-7.8 pg/g toxic equivalent quotients for the individual PCDD/Fs. Lower detection limits can be achieved by using larger sample size and scaling up the sample preparation procedure, but this adds to the labor, time, solvent consumption, and expense of the approach. However, the streamlined method yielded 0.94 pg/g and 2.3 pg/g LOQs for 2,3,7,8-tetrachloro dibenzofuran (TCDF) and 3,3',4,4',5-pentachloro biphenyl (CB126), which were sufficiently low for regulatory monitoring of 2g samples. Therefore, instead of congener specific analysis, this streamlined analytical screening method for TCDF and CB126 has the potential to monitor fish oil contaminated with dioxin and dioxin-like PCBs at or above current food safety limits. Acceptable recoveries for nearly all analytes at three different spiking levels in fish oil samples were achieved with good repeatability.     

杭州市冬季大气气溶胶PM2.5中二恶英和多氯联苯的污染特征

2014年1月在杭州市选择5个点位采集大气颗粒物PM_2.5样品,采用同位素稀释高分辨气相色谱/高分辨质谱测定PM_2.5中的二恶英（PCDD/Fs）和多氯联苯（PCBs）,对PM_2.5的污染状况以及PM_2.5中PCDD/Fs和PCBs的污染水平及分布特征进行了研究。PM_2.5的质量浓度范围为85~168 μg/m³,PM_2.5污染较重,但与2004年同期相比明显降低。PM_2.5中PCDD/Fs的毒性当量（TEQ）为0.277~0.488 pg I-TEQ/m³,明显高于2004年同期采集样品。颗粒物中PCDD/Fs以八氯代二苯并-对-二恶英（OCDD）为主,毒性当量主要贡献者为2,3,4,7,8-五氯代二苯并呋喃（2,3,4,7,8-PeCDF）。PM_2.5中PCBs的质量浓度范围为2.9~8.1 pg/m³,二恶英类多氯联苯（DL-PCBs）的毒性当量范围为2.6~6.1 fg WHO-TEQ/m³,污染较低。PCBs在颗粒物中分布以PCB-28为主,但对毒性当量贡献最大的为PCB-126。PCDD/Fs和PCBs的气-固分配特征表现为PCDD/Fs主要分布于颗粒物中,而PCBs主要分布于气相中。     

Optimized determination of polybrominated diphenyl ethers and polychlorinated biphenyls in sheep serum by solid-phase extraction-gas chromatography-mass spectrometry

We describe a solid-phase extraction (SPE) method, followed by gas chromatography-mass spectrometry (GC-MS), for the simultaneous determination of polybrominated diphenyl ethers (PBDEs) and polychlorinated biphenyls (PCBs) in sheep serum samples. The denaturation of serum proteins by formic acid, water-1-propanol and water-2-propanol were compared and optimized. Seven different solid-phase sorbents were tested and it was found that Strata-X cartridge (200 mg, 6 mL) gave the best recoveries (92-106%, SD < 6%, n = 3) for all the target analytes. The different extraction solvents (iso-hexane and dichloromethane), either alone or in combination, were used to extract these persistent organic compounds from spiked serum samples by SPE. Removal of co-extracted biogenic materials was achieved using adsorption chromatography with acid modified silica and activated silica. Iso-hexane was found to be the most appropriate solvent for clean-up providing good recoveries and clear chromatographic separation; its use is preferable to that of DCM because it is less environmentally toxic. The limits of detection (LOD) of the proposed method were 47-105 pg g⁻¹ and 16-24 pg g⁻¹ for the different PBDEs and PCBs studied, respectively. The developed method was linear over the range from 0.05 to 30 ng g⁻¹, for all PBDEs except PBDE 183 (0.10-30 ng g⁻¹), and from 0.02 to 30 ng g⁻¹ for all tested PCB congeners. The established method was successfully applied to sheep serum samples from Scotland, UK, for the determination of the target PBDEs and PCBs.