Determination of total nitrogen in food by flow injection analysis (FIA) with a potentiometric differential detection system

A flow injection set-up based on potentiometric detection and gas diffusion device for the determination of total nitrogen in food is described. The detection system consisted of two ammonium-sensitive electrodes placed sequentially and each alternately operating as reference electrode. Tubular electrodes without an inner reference solution were prepared with a PVC membrane composed of nonactin in Tris (2-ethylhexyl) phosphate and potassium tetrakis (4-chlorophenyl) borate to reduce the membrane resistance. The food sample digests were inserted into the system, and the ammonium present was converted into ammonia gas. The gas diffused through a gas-permeable membrane to a buffer acceptor stream with a pH that ensured transformation to the ammonium cation, which was potentiometrically detected. Good agreement between FIA results and those provided by the reference procedure was obtained, with relative deviation errors below 5%. Using the proposed system, low reagent consumption is possible, a sampling rate of about 30 samples/h was achieved, as well as a good reproducibility for consecutive injections of the same sample (variation coefficient < 2%).     

微流控芯片流动注射气体扩散分离光度测定系统的研究

提出了纳升级进样量的微流控芯片流动注射气体扩散分离光度检测系统. 制作三层结构微流控芯片, 在玻璃片上加工微反应通道, 用聚二甲基硅氧烷[Poly(dimethylsiloxane), PDMS]加工气体渗透膜和具有接收气体微通道的底片, 实现了生成气体的化学反应、气-液分离和检测在同一微芯片上的集成化. 采用缝管阵列纳升流动注射进样系统连续进样, 用吸光度法测定NH+4以验证系统性能. 结果表明， 该系统对NH+4的检出限为140 μmol/L(3σ), 峰高精度为3.7%(n=9). 在进样时间12 s、注入载流48 s和每次进样消耗200 nL试样条件下, 系统分析通量可达60样/h. 若加大样品量到800 nL, 使接收溶液停流1 min, 该系统对NH+4的检出限可达到35 μmol/L(3σ), 但分析通量降低到20样/h.     

Flow injection colorimetric method using acidic ceric nitrate as reagent for determination of ethanol

Ceric ammonium nitrate has been used for qualitative analysis of ethanol. It forms an intensely colored unstable complex with alcohol. In this work, a simple flow injection (FI) colorimetric method was developed for the determination of ethanol, based on the reaction of ethanol with ceric ion in acidic medium to produce a red colored product having maximum absorption at 415 nm. Absorbance of this complex could be precisely measured in the FI system. A standard or sample solution was injected into a deionized water donor stream and flowed to a gas diffusion unit, where the ethanol diffused through a gas permeable membrane made of plumbing PTFE tape into an acceptor stream to react with ceric ammonium nitrate in nitric acid. Color intensity of the reddish product was monitored by a laboratory made LED based colorimeter and the signal was recorded on a computer as a peak. Peak height obtained was linearly proportional to the concentration of ethanol originally presented in the injected solution in the range of 0.1-10.0% (v/v) (r² = 0.9993), with detection limit of 0.03% (v/v). With the use of gas diffusion membrane, most of the interferences could be eliminated. The proposed method was successfully applied for determination of ethanol in some alcoholic beverages, validating by gas chromatographic method.     

Multielement analysis of whole blood by high resolution inductively coupled plasma mass spectrometry

An analytical method using double focusing sector field inductively coupled plasma mass spectrometry (ICP-SMS) for rapid simultaneous determination of 50 elements in digested human blood is described. Sample preparation consisted of microwave digestion with nitric acid followed by dilution with ultrapure water. The importance of controlling possible contamination sources at different sample preparation and analysis stages in order to achieve adequate method detection limits (MDL) is emphasised. Correction for matrix effects was made using scandium, indium and lutecium as internal standards. Accuracy of the data for elements suffering from spectral interferences was improved by applying either a high resolution capability of the ICP-SMS or mathematical corrections. Different approaches for accuracy assessment in blood analysis are evaluated. Additional information on trace elements concentration in selected blood reference materials is given. The between-batch precision was assessed from replicate analysis (including sample preparation) of reference materials and was better than 10% RSD for 21 elements and better than 30% RSD for 36 elements under consideration. A statistical summary for results obtained for 31 blood samples from non-exposed subjects is presented. The majority of elements tested was found in the samples at concentrations higher than MDL. Received: 23 November 1998 / Revised: 6 January 1999 / Accepted: 12 January 1999     

The synthesis and membrane transport characteristics of macrocyclic polyether ligands composed of 1,10-phenanthroline as carriers for primary amine species

Four macrocyclic polyether derivatives of o-phenanthroline were synthesized and used as neutral carriers for preparing poly(vinyl chloride) (PVC) membrane electrodes to sense primary amine species. The potentiometric response characteristics of the electrodes prepared were investigated. The electrode sensitive to benzyl amine as model analyte showed a linear response range of 8.0 x 10(-6)-0.1 mol/l with a detection limit of 8.9 x 10(-7) mol/l and a slope of 56.5 mV/decade. The linear potentiometric response of the mexiletine-sensitive electrode was 4.7 x 10(-6)-0.1 mol/l, and the detection limit was 5.0 x 10(-7)1 mol/l with a slope of 59.0 mV/decade. The transfer behavior of amines and ammonium ions through an organic phase was investigated by means of the bulk liquid membrane transport experiment. The effects of pH, counter anions and other factors on the transfer of the amine and ammonium species were studied. The mass transfer rates of the test species facilitated by macrocyclic polyether derivatives of o-phenanthroline were determined and the following sequence was found: benzyl amine > ethyl amine > tetramethyl ammonium > triethyl amine > diethyl amine > K(+) > ammonium > Na(+) > Ca(2+) > Mg(2+). This was exactly the potentiometric selectivity sequence of the membrane electrodes prepared by using these carriers. The mechanism of transfer of benzyl amine through a membrane phase induced by the carriers has been elucidated on the basis of experimental observations.     

HPLC online reductive scanning voltammetric detection of diquat, paraquat and difenzoquat with mercury electrodes

To establish an electrochemical HPLC detection system which is suitable for the voltammetric characterisation of unknown contaminants and food components at working potentials lower than –1 V, a modified flow-through cell for the use of a hanging mercury drop electrode (HMDE) is described. The introduction of silanised glass capillaries and a new flow-channel design provide a high HMDE lifetime, which is recommended in HPLC detection. As test system the herbicides diquat, paraquat and difenzoquat and ethylviologen as internal standard were measured using differential pulse voltammetry (DPV) detection to improve selectivity. Spiked water samples were analysed with voltammetric and UV-detection and results agreed well. Received: 12 November 1998 / Revised: 21 January 1999 / Accepted: 26 January 1999     

Conductometric determination of ammonium by a multisyringe flow injection system applying gas diffusion

A multisyringe flow injection system (MSFIA) coupled to a gas-diffusion cell has been developed for the conductometric determination of ammonium in different water samples. Operation strategies, membrane, reagent concentrations, and flow rates have been studied to optimize the sensitivity of detection and to fit the required working range. The proposed MSFIA system has been compared with former FIA and SIA systems using gas diffusion. The system was applied to the determination of ammonium in water samples of different matrices in order to evaluate its performance. These samples were coastal waters, pond waters, and compost aqueous extracts. Good recoveries of 102?±?13% were obtained and no significant differences with the reference methods were found. The system can be used for a wide concentration range of ammonia, from 0.075 to 360?mg?L^?1, without sample dilution and with a precision better than 2% of RSD. The throughput of the method was 32 injections per hour.     

A direct comparison of amperometric gas sensors with gas-diffusion and ion-exchange membrane based electrodes

The effect of the nature of the working electrode used in amperometric gas sensors on the performance criteria of sensitivity, detection limit, gas flow rate and humidity dependence was evaluated. The arrangement based on metallized ion-exchange membranes (Nafion) was compared with gas-diffusion electrodes based on porous poly(tetrafluoroethylene) (PTFE) with metallic electrodes deposited on the rear side. Two representative analyte gases were chosen: SO2, which has fast reaction kinetics, and NO, which has slow reaction kinetics. It was found that both types of electrodes showed a similar performance. A dependence on the flow rate of the sample gas was found in both cases. The sensitivities were higher for the ion-exchange membrane-backed electrodes; however, the 3sigma detection limits were all in the lower ppb range and for NO were significantly lower on the Nafion membrane than on the PTFE membrane. The Nafion electrode was found to show a dependence on the relative humidity of the gas stream, but not the PTFE-based electrode.     

Investigation of the analytical performance of gliding spark source mass spectrometry (GSSMS) for the trace analysis of nonconducting materials

A radiofrequency (rf) spark discharge in vacuum developing across the surface of dielectrics – a so-called gliding spark – has been applied to the direct mass spectrometric trace analysis of nonconducting materials. The special configuration of the electrodes strengthened the electric field over the surface of a nonconducting sample and created optimum conditions for the sputtering and ionization of the sample material. Mass spectrometric investigations of the charge composition of atomic ion and molecular ion formation in radiofrequency gliding spark plasma showed a significant difference to that of the original rf spark discharge between two conducting electrodes. The analytical figures of merit (reproducibility, relative sensitivity factors and detection limits of chemical elements) of gliding spark source mass spectrometry have been studied by using the glass standard reference materials NIST SRM 610 and 611 for the determination of trace elements in glass matrix. Received: 31 March 1999 / Revised: 10 May 1999 / Accepted: 13 May 1999     

Flow injection system with gas diffusion for the sequential determination of total nitrogen and phosphorus in vegetables

 A flow injection system was developed for the sequential determination of total nitrogen and phosphorus in digests of vegetables using potentiometric and spectrophotometric detection systems, respectively. A tubular ammonium selective electrode with a sensor system composed of nonactin/monactin in tris(2-ethylhexyl) phosphate was used. The selectivity limitations of this electrode were overcome by the inclusion of a gas-diffusion unit in the system that separated ammonium from the rest of the sample matrix and allowed the determination of total nitrogen and phosphorus by the partition of the sample plug between two streams. The results obtained with the developed FIA system were in good agreement with those of the reference methods. Sampling rates from 40 to 60 samples per hour and relative standard deviations below 3.5% were achieved. Received: 17 October 1996/Revised: 21 November 1996/Accepted: 27 November 1996     

Flow injection system with gas diffusion for the sequential determination of total nitrogen and phosphorus in vegetables

 A flow injection system was developed for the sequential determination of total nitrogen and phosphorus in digests of vegetables using potentiometric and spectrophotometric detection systems, respectively. A tubular ammonium selective electrode with a sensor system composed of nonactin/monactin in tris(2-ethylhexyl) phosphate was used. The selectivity limitations of this electrode were overcome by the inclusion of a gas-diffusion unit in the system that separated ammonium from the rest of the sample matrix and allowed the determination of total nitrogen and phosphorus by the partition of the sample plug between two streams. The results obtained with the developed FIA system were in good agreement with those of the reference methods. Sampling rates from 40 to 60 samples per hour and relative standard deviations below 3.5% were achieved. Received: 17 October 1996/Revised: 21 November 1996/Accepted: 27 November 1996     

Simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional ion-selective electrodes in series

An on-line automated system for the simultaneous flow injection determination of calcium and fluoride in natural and borehole water with conventional calcium-selective and fluoride-selective membrane electrodes as sensors in series is described. Samples (30 μl) are injected into a TISAB II (pH=5.50) carrier solution as an ionic strength adjustment buffer. The sample-buffer zone formed is first channeled to a fluoride-selective membrane electrode and then via the calcium-selective membrane electrode to the reference electrodes. The system is suitable for the simultaneous on-site monitoring of calcium (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 1.94×10⁻⁶ mol l⁻¹ recovery 99.22%, RSD<0.5%) and fluoride (linear range 10⁻⁵–10⁻² mol l⁻¹ detection limit 4.83×10⁻⁶ mol l⁻¹ recovery 98.63%, RSD=0.3%) at a sampling rate of 60 samples h⁻¹.     

Determination of palladium in deoxo catalysts by differential pulse voltammetry

A differential pulse voltammetric (DPV) method is proposed for the determination of palladium in deoxo catalysts, which are used in recombination units of the cover gas system of nuclear reactors. The electrode system consists of hanging mercury drop electrode (HMDE)/ platinum auxillary/ Ag-AgCl reference electrode. The supporting electrolyte consists of 0.02 M diammonium tartrate + 0.08 M ammonia-ammonium chloride buffer at pH 9.0. Fe, Cu, Pb, Ni, Co and Zn did not interfere. The interference by Cd could be eliminated using 0.005 M EDTA. The relative standard deviation of the proposed method was about 4.0% at ∼ 0.5% palladium content in the catalyst. The method is simple, rapid and free from any possible interferences. Received: 8 December 1998 / Revised: 11 January 1999 / Accepted: 18 January 1999     

Flow injection conductometric system with gas diffusion separation for the determination of Kjeldahl nitrogen in milk and chicken meat

A simple flow injection (FI) conductometric system with gas diffusion separation was developed for the determination of Kjeldahl nitrogen (or proteins) in milk and chicken meat. The sample was digested according to the Kjeldahl standard method and the digest was diluted and directly injected into the donor stream consisting of 4 M NaOH. In alkaline medium, ammonium was converted to ammonia, which diffused through the PTFE membrane to dissolve in an acceptor stream (water). Dissociation of ammonia caused a change in conductance of the acceptor solution, which was linearly proportional to the concentration of ammonium originally present in the injected solution. A conductometric flow through cell and an amplifier circuit was fabricated, which helped improve sensitivity of the conductometric detection system. With using a plumbing Teflon tape as a gas diffusion membrane and without thermostating control of the system, a linear calibration graph in range of 10-100 mg L⁻¹ N-NH₄ was obtained, with detection limit of 1 mg L⁻¹ and good precision (relative standard deviation of 0.3% for 11 replicate injections of 50 mg L⁻¹ N-NH₄). The developed method was validated by the standard Kjeldahl distillation/titration method for the analysis of milk and chicken meat samples. The proposed system had sample throughput of 35 h⁻¹ and consumed much smaller amounts of chemical than the standard method (275 mg vs 17.5 g of NaOH per analysis, respectively).     

Microband Sensor for As(III) Analysis: Reduced Matrix Interference

A portable sensor based on a microband design for arsenic detection in drinking water is presented. The work was focused to minimize interference encountered with a standard screen‐printed electrodes featuring an onboard gold working electrode, carbon counter and silver−silver chloride pseudo‐reference electrodes as composite coatings on plastic surface. The interference effect was identified as chloride ions interacting with the silver surface of the reference electrode and formation of soluble silver chloride complexes such as AgCl₄³⁻. By modification of the reference electrodes with Nafion membrane (5 % in alcohols), the interference was entirely eliminated. However, membrane coverage and uniformity can impact the electrodes reproducibility and performance. Hence, the sensor design was further considered and a microband format was produced lending favorable diffusive to capacitive current characteristics. Using the microband electrodes allowed As(III) detection with limit of detection of 0.8 ppb (in 4 M HCl electrolyte), inherently avoiding the problems of electrode fouling and maximizing analyte signal in river water samples. This is below the World Health Organization limit of 10 μg L⁻¹ (ppb). The electrolyte system was chosen so as to avoid problems from other common metal ions, most notably Cu(II). The presented electrode system is cost effective and offers a viable alternative to the colorimetric test kits presently employed for arsenic analysis in drinking water.     

Flow methodology for methanol determination in biodiesel exploiting membrane-based extraction

A methodology based in flow analysis and membrane-based extraction has been applied to the determination of methanol in biodiesel samples. A hydrophilic membrane was used to perform the liquid-liquid extraction in the system with the organic sample fed to the donor side of the membrane and the methanol transfer to an aqueous acceptor buffer solution. The quantification of the methanol was then achieved in aqueous solution by the combined use of immobilised alcohol oxidase (AOD), soluble peroxidase and 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS). The optimization of parameters such as the type of membrane, the groove volume and configuration of the membrane unit, the appropriate organic solvent, sample injection volume, as well as immobilised packed AOD reactor was performed. Two dynamic analytical working ranges were achieved, up to 0.015% and up to 0.200% (m/m) methanol concentrations, just by changing the volume of acceptor aqueous solution. Detection limits of 0.0002% (m/m) and 0.007% (m/m) methanol were estimated, respectively. The decision limit (CCα) and the detection capacity (CCβ) were 0.206 and 0.211% (m/m), respectively. The developed methodology showed good precision, with a relative standard deviation (R.S.D.) <5.0% (n = 10). Biodiesel samples from different sources were then directly analyzed without any sample pre-treatment. Statistical evaluation showed good compliance, for a 95% confidence level, between the results obtained with the flow system and those furnished by the gas chromatography reference method. The proposed methodology turns out to be more environmental friendly and cost-effective than the reference method.     

Analytical procedure for the simultaneous voltammetric determination of trace metals in food and environmental matrices. Critical comparison with atomic absorption spectroscopic measurements

An analytical procedure fit for the simultaneous determination of copper (II), chromium(VI), thallium(I), lead(II), tin(II), antimony(III), and zinc(II) by square wave anodic stripping voltammetry (SWASV) in three interdependent environmental matrices involved in foods and food chain as meals, cereal plants and soils is described. The digestion of each matrix was carried out using a concentrated HCl-HNO3-H2SO4 (meals and cereal plants) and HCl-HNO3 (soils) acidic attack mixtures. 0.1 mol/L dibasic ammonium citrate pH 8.5 was employed as the supporting electrolyte. The voltammetric measurements were carried out using, as working electrode, a stationary hanging mercury drop electrode (HMDE) and a platinum electrode and an Ag/AgCl/KClsat electrode as auxiliary and reference electrodes, respectively. The analytical procedure was verified by the analyses of the standard reference materials: Wholemeal BCR-CRM 189, Tomato Leaves NIST-SRM 1573a and Montana Soil Moderately Elevated Traces NIST-SRM 2711. For all the elements in the certified matrix, the precision as repeatability, expressed as relative standard deviation (Sr %) was lower than 5%. The accuracy, expressed as percentage relative error (e %) was of the order of 3-7%, while the detection limits were in the range 0.015-0.103 microg/g. Once set up on the standard reference materials, the analytical procedure was transferred and applied to commercial meal samples, cereal plants and soils samples drawn in sites devoted to agricultural practice. A critical comparison with spectroscopic measurements is also discussed.     

邻菲咯啉冠醚衍生物为载体的伯胺药物电极及机理研究

合成了邻菲咯啉-18-冠-6等四种含邻菲咯啉结构的冠醚化合物, 并用作载体制备伯胺电极, 以苄胺为模型化合物, 研究了电极特性, 并制备了测试美西律药物的选择性电极。研究了实验条件对电极性能的影响。用正交多项式回归法优化电极的膜组成。苄胺电极的线性范围1.0×10^-5~0.1mol/L, 斜率55.6mV/pc, 检测下限2.0×10^-6mol/L。美西律电极的线性范围6.0×10^-6~0.1mol/L, 检测下限8.0×10^-7mol, 斜率58.0mV/pc。同时研究了冠醚推动伯胺穿透大块液膜的传输行为。     

Solid-phase microextraction for the assay of clozapine in human plasma

Solid-phase microextraction (SPME) was investigated as sample preparation for the assay of the neuroleptic drug clozapine in human plasma. A mixture of human plasma, water, loxapine as internal standard and aqueous NaOH was extracted with a 100 μm-polydimethylsiloxane-(PDMS)-fiber for 30 min. The analyte and internal standard were well separated in the gas chromatogram. The calibration was linear and passed the origin. Accuracy and precision as well as the influence of changes of the matrix were investigated. No interfering drug was found. It is concluded that the method can be used in the therapeutic drug monitoring of clozapine. Received: 23 December 1998 / Revised: 27 January 1999 / Accepted: 31 January 1999     

Evaluation of Water Ammonium Ion Test Kit and Its Feasibility for the Analysis of Protein in Food

The traditional method for the determination of protein in food needs the operations of digestion, distillation, absorption, and titration; therefore, it is complicated and time-consuming and requires professional personnel. Is there a more convenient and faster detection method that can directly determine the ammonium ions in protein digestion solution to obtain the protein content of food and avoid the distillation–absorption–titration process? The feasibility of water ammonium ion test kits for food protein rapid detection was discussed here. After digestion, the protein in food transforms into ammonium ions in the digestion solution. Because of the variety of food, there are many different inorganic ions left in the food digestion solution, and at the same time, digestion agents are added in the digestion process and become potential interference factors in ammonium determination. Therefore, the detection accuracy of ammonium test kits needs to be evaluated first, including their anti-interference ability. The standard curve of ammonium was established by the test kit. When the ammonium concentration was 0.00–2.50 mg/L, the absorbance at 620 nm was linearly related to the ammonium concentration, the determination coefficient R² was 0.9995, and the detection limit of this method was 0.01 mg/L. The influences of temperature, pH value, and reaction time on the test kit method were discussed. The precision was 0.90–3.33%; the repeatability was 1.71–4.86%; and the recovery rate of tap water, river water, and sea water was controlled within 90–103%. The anti-interference ability of the evaluated test kit was better than that of the national standard detection method. The test kit, combined with sample pretreatment and protein conversion formula, was used to detect protein in different types of food (milk powder, rice flour, wheat flour, soy, banana, milk, fish food, chicken food, and dog food). The results showed that there were no significant differences (ρ > 0.05) between the national method and the test kit method. The ammonium ion test kit method shortened the determination time and had higher sensitivity, showing its potential for the rapid determination of food protein.