Improving rate performance of cathode material Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Co<Subscript>0.13</Subscript>Ni<Subscript>0.13</Subscript>O<Subscript>2</Subscript> via niobium doping

As a promising Li-ion battery cathode active material, lithium-rich manganese-based layer-structured oxides suffer from inferior cycle performance and poor rate capability. Herein, Nb-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ is prepared by a sol-gel method, and the effects of Nb doping on its electrochemical performance are investigated. It is concluded that the Nb-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂, has a good layered structure along c-axis independent on the amount of Nb dopant and little cationic mixing. Nb doping for Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has no obvious influence on its morphology. It is found that Nb doping can enhance the electrochemical activity of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂, such as improved rate performance and cycle performance under high rate conditions. Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ doped with 0.015 Nb shows the best cycle performance under the high rate with the capacity maintenance of 95.4% after 100 cycles under 5 C rate, which is higher than that of the undoped one by 10.5%.

Open image in new window

Graphical abstract Rate performance of Li_1.2Mn_0.54-xCo_0.13Ni_0.13Nb _x O₂ materials

     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Porous,hollow Li<Subscript>1.2</Subscript>Mn<Subscript>0.53</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> microspheres as a positive electrode material for Li-ion batteries

A porous, hollow, microspherical composite of Li₂MnO₃ and LiMn_1/3Co_1/3Ni_1/3O₂ (composition: Li_1.2Mn_0.53Ni_0.13Co_0.13O₂) was prepared using hollow MnO₂ as the sacrificial template. The resulting composite was found to be mesoporous; its pores were about 20 nm in diameter. It also delivered a reversible discharge capacity value of 220 mAh g^?1 at a specific current of 25 mA g^?1 with excellent cycling stability and a high rate capability. A discharge capacity of 100 mAh g^?1 was obtained for this composite at a specific current of 1000 mA g^?1. The high rate capability of this hollow microspherical composite can be attributed to its porous nature.

Open image in new window

Graphical Abstract ?

     

Synthesis and electrochemical performance of the Li-rich cathode material Li<Subscript>1.17</Subscript>Ni<Subscript>0.12</Subscript>Co<Subscript>0.13</Subscript>Mn<Subscript>0.58</Subscript>O<Subscript>2</Subscript> for lithium-ion batteries

Lithium-riched cathode material for lithium-ion batteries, Li_1.17Ni_0.12Co_0.13Mn_0.58O₂, was synthesized via crystallization from a solution of metal acetates, followed by a thermal treatment of the material obtained as a powder. The phase, elemental, and granulometric compositions of the material were examined, as well as the morphology of the powder particles obtained. The discharge capacity of the material in relation to the charging voltage was found from the results of electrochemical tests, and endurance tests were performed. The discharge capacity upon 85 charge/discharge cycles at voltages in the range 2.8–4.8 and a current of 0.1C was about 180 mA h g^–1.     

Synthesis and electrochemical properties of Li-rich Li[Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>]O<Subscript>2</Subscript> for pouch-typed cell

Layered transition metal oxide LiNi _x Co _y MnzO₂ cathode materials with different Li amount were successfully synthesized via co-precipitation method. Monodispersed Li[Ni_0.5Co_0.2Mn_0.3]O₂ and Li-rich Li_1.1[Ni_0.5Co_0.2Mn_0.3]O₂ spherical agglomeration consisted of secondary particles, which is favorable for the higher tap-density of materials, can be easily obtained. The pouch-typed cells with obtained materials were assembled to investigate electrochemical performance at level of full-cell. The results show that the assembled pouch-typed full-cells with Li-rich sample present higher capacity, better rate capability and cycle life.     

Ammonium tungstate modified Li-rich Li<Subscript>1+x</Subscript>Ni<Subscript>0.35</Subscript>Co<Subscript>0.35</Subscript>Mn<Subscript>0.30</Subscript>O<Subscript>2</Subscript> to improve rate capability and productivity of lithium-ion batteries

LiNi_1-x-yCo_xMn_yO₂ (NCM) with excessive lithium is known to exhibit high rate capability and charge–discharge cycling durability. However, the practical usage of NCM is difficult, because the positive electrode slurry is unstable and battery cells swell due to the alkaline residual lithium compound generated on the surface of NCM particles. To reduce the residual lithium compound, ammonium metatungstate (AMT) added to NCM is studied, and the effect is investigated by scanning electron microscopy, aberration-corrected scanning transmission electron microscopy, X-ray diffractometry, synchrotron X-ray diffractometry, and several electrochemical measurements. It is found that the AMT modification reduces the amount of alkaline residual lithium compound and improves the rate capability due to the ~1-nm-thick W-rich layer generated on the NCM surface.

Open image in new window

Graphical abstract ?

     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Correlation between the structural,electrical and electrochemical performance of layered Li(Ni<Subscript>0.33</Subscript>Co<Subscript>0.33</Subscript>Mn<Subscript>0.33</Subscript>)O<Subscript>2</Subscript> for lithium ion battery

The Li(Ni_0.33Co_0.33Mn_0.33)O₂ (LNCMO) cathode material is prepared by poly(vinyl pyrrolidone) (PVP)-assisted sol-gel/hydrothermal and poly(ethylene glycol)-block-poly(propylene glycol)-block-poly (ethylene glycol) (Pluronic-P123)-assisted hydrothermal methods. The compound prepared by PVP-assisted hydrothermal method shows a comparatively higher electrical conductivity of ~2?×?10^?5 S cm^?1 and exhibits a discharge capacity of 152 mAh g^?1 in the voltage range of 2.5 to 4.4 V, for a C-rate of 0.2 C, whereas the compounds prepared by P123-assisted hydrothermal method and PVP-assisted sol-gel method show a total electrical conductivity in the order of 10^?6 S cm^?1 and result in poor electrochemical performance. The structural and electrical properties of LNCMO (active material) and its electrochemical performance are correlated. The difference in percentage of ionic and electronic conductivity contribution to the total electrical conductivity is compared by transference number studies. The cation disorder is found to be the limiting factor for the lithium ion diffusion as determined from ionic conductivity values.     

Preparation and adsorption of magnetic Co<Subscript>0.5</Subscript>Ni<Subscript>0.5</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>-chitosan nanoparticles

In this paper, magnetic chitosan microspheres were prepared by the emulsification cross-linking technique, with glutaraldehyde as the cross-linking agent, liquid paraffin as the dispersant, and the Span-80 as emulsifier. The time of cross-linking and the ratio of Co_0.5Ni_0.5Fe₂O₄/chitosan were investigated. The morphology was studied by different instruments. The adsorption performance was investigated and the effects of initial concentration of methyl orange, the time of cross-linking, and the amount of adsorbent were discussed. It is found that the product has uniform morphology when the ratio of magnetic Co_0.5Ni_0.5Fe₂O₄/chitosan is 1 : 2 and the time of cross-linking is 5 h; At room temperature, magnetic Co_0.5Ni_0.5Fe₂O₄–chitosan has a good adsorption toward methyl orange when the magnetic Co_0.5Ni_0.5Fe₂O₄/chitosan dosage is 20 mg.     

Synthesis and Electrocatalytic Properties of Co<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanocrystallites with Various Morphologies

Co₃O₄ crystallites with particle, plate-, tube-, rod- and sheet-like morphologies were successfully prepared by the calcination of the corresponding precursors synthesized via a precipitation or hydrothermal procedure. The morphologies of the precursors and Co₃O₄ nano-tubes were detected by field emission scanning electron microscopy (FE-SEM). The as-obtained Co₃O₄ samples were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and special surface area measurement (BET). The electrocatalytic activity of p-nitrophenol reduction with the Co₃O₄ products decorated on a glassy carbon electrode (GCE) was tested, respectively, using cyclic voltammetry (CV) in a basic solution. The results indicated that p-nitrophenol was reduced with higher current density but almost at a constant potential on the Co₃O₄/GCE in contrast with that on a bare GCE at the same conditions. The highly catalytic activity of the as-prepared Co₃O₄ in a basic solution suggested their wide applications in environmental treatment or organic synthesis.     

Kinetics of the uninhibited and ethanol-inhibited CoO,Co<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyzed autoxidation of sulfur(IV) in alkaline medium

For getting an insight into the mechanism of atmospheric autoxidation of sulfur(IV), the kinetics of this autoxidation reaction catalyzed by CoO, Co₂O₃ and Ni₂O₃ in buffered alkaline medium has been studied, and found to be defined by Eqs. I and II for catalysis by cobalt oxides and Ni₂O₃, respectively.

Ammonia gas sensor based on a spinel semiconductor,Co<Subscript>0.8</Subscript>Ni<Subscript>0.2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanomaterial

Thick film of nanocrystalline Co_0.8Ni_0.2Fe₂O₄ was obtained by sol–gel citrate method for gas sensing application. The synthesized powder was characterized by X-ray diffraction (XRD) and transmission electron microscopy. The XRD pattern shows spinel type structure of Co_0.8Ni_0.2Fe₂O₄. XRD of Co_0.8Ni_0.2Fe₂O₄ revels formation of solid solution with average grain size of about 30 nm. From gas sensing properties it observed that nickel doping improves the sensor response and selectivity towards ammonia gas and very low response to LPG, CO, and H₂S at 280 °C. Furthermore, incorporation of Pd improves the sensor response and stability of ammonia gas and reduced the operating temperature upto 210 °C. The sensor is a promising candidate for practical detector of ammonia.     

Phase equilibria in the system Li<Subscript>2</Subscript>O-MgO-B<Subscript>2</Subscript>O<Subscript>3</Subscript>

The subsolidus region of the Li₂O-MgO-B₂O₃ system has been studied by X-ray powder diffraction and differential thermal analysis. Isothermal sections at 500–550 and 650–700°C have been designed. The following complex borates have been found to form: at 500–550°C, Li₂MgB₂O₅ and LiMgBO₃ are formed; at 650–700°C, a new phase Li₄MgB₂O₅ is formed along with LiMgBO₃; and at 5500–600°, Li₂MgB₂O₅ is formed.     

Effect of the preparation method of the cathode material LiNi<Subscript>0.33</Subscript>Mn<Subscript>0.33</Subscript>Co<Subscript>0.33</Subscript>O<Subscript>2</Subscript> on the electrochemical characteristics of a lithium ion cell

Complex metal oxides with the composition LiNi_0.33Mn_0.33Co_0.33O₂ prepared by various methods: sol–gel method, solid-phase method, and thermal destruction of metal-containing compounds in oil were studied. The results of elemental analysis, TGA/DSC, powder X-ray diffraction, SEM, TEM, as well as the results of electrochemical testing of the cathodes based on the obtained materials are presented. The complex metal oxides LiNi_0.33Mn_0.33Co_0.33O₂ prepared by sol–gel processes and thermal destruction of metal-containing compounds in oil consist of primary nanosized crystallites with an average size of 90 nm covered by a nanometer carbon layer, which improves the electrochemical characteristics of lithium ion batteries.     

Effects of Mg,Al Co-doping into Mn site on electrochemical performance of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript>

In order to study the influence of multiple ions doping into single-site on the structure and electrochemical properties of Ni-rich layered-structure cathode material LiNi_0.5Co_0.2Mn_0.3O₂, the coprecipitation of hydroxides was applied to synthesize Mg, Al co-doped cathode material LiNi_0.5Co_0.2Mn_0.3–x Mg_1/2x Al_1/2x O₂ (x = 0.00, 0.01, 0.02, 0.04) in this paper. Morphology and structure, kinetic parameter, impedance and electrochemical performance of the material were respectively characterized by SEM, XRD, CV, EIS and galvanostatic charge/discharge test. The results of comprehensive analysis showed that the properties of material were improved obviously when the amount of doping was 0.02. At this amount of doping, the corresponding material has smaller cation mixing, higher hexagonal ordering of layered-structure, larger Li⁺ ion diffusion coefficients which are 2.444 × 10^–10 and 4.186 × 10^–10 cm² s^–1 for Li+ intercalation and deintercalation respectively, smaller impedance which is 33.93 Ω, higher specific capacity of first-discharge which is 168.01 mA h g^–1 and higher capacity retention rate which is up to 95.06% after 20 cycles at 0.5 C (100 mA g^–1).     

Rational design of double-confined Mn<Subscript>2</Subscript>O<Subscript>3</Subscript>/S@Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocube cathodes for lithium-sulfur batteries

Due to the high specific capacities and environmental benignity, lithium-sulfur (Li-S) batteries have shown fascinating potential to replace the currently dominant Li-ion batteries to power portable electronics and electric vehicles. However, the shuttling effect caused by the dissolution of polysulfides seriously degrades their electrochemical performance. In this paper, Mn₂O₃ microcubes are fabricated to serve as the sulfur host, on top of which Al₂O₃ layers of 2 nm in thickness are deposited via atomic layer deposition (ALD) to form Mn₂O₃/S (MOS) @Al₂O₃ composite electrodes. The MOS@Al₂O₃ electrode delivers an excellent initial capacity of 1012.1 mAh g^?1 and a capacity retention of 78.6% after 200 cycles at 0.5 C, and its coulombic efficiency reaches nearly 99%, giving rise to much better performance than the neat MOS electrode. These findings demonstrate the double confinement effect of the composite electrode in that both the porous Mn₂O₃ structure and the atomic Al₂O₃ layer serve as the spacious host and the protection layer of sulfur active materials, respectively, for significantly improved electrochemical performance of the Li-S battery.     

2-pyrrolidone - capped Mn<Subscript>3</Subscript>O<Subscript>4</Subscript> nanocrystals

Water-soluble Mn₃O₄ nanocrystals have been prepared through thermal decomposition in a high temperature boiling solvent, 2-pyrrolidone. The final product was characterized with XRD, SEM, TEM, FTIR and Zeta Potential measurements. Average crystallite size was calculated as ∼15 nm using XRD peak broadening. TEM analysis revealed spherical nanoparticles with an average diameter of 14±0.4 nm. FTIR analysis indicated that 2-pyrrolidone coordinates with the Mn₃O₄ nanocrystals only via O from the carbonyl group, thus confining their growth and protecting their surfaces from interaction with neighboring particles.      

Synthesis and characterization of Co<Subscript>0.8</Subscript>Zn<Subscript>0.2</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles

Cobalt zinc ferrite, Co_0.8Zn_0.2Fe₂O₄, nanoparticles have been synthesized via autocatalytic decomposition of the precursor, cobalt zinc ferrous fumarato hydrazinate. The X-ray powder diffraction of the ‘as prepared’ oxide confirms the formation of single phase nanocrystalline cobalt zinc ferrite nanoparticles. The thermal decomposition of the precursor has been studied by isothermal, thermogravimetric and differential thermal analysis. The precursor has also been characterized by FTIR, and chemical analysis and its chemical composition has been determined as Co_0.8Zn_0.2Fe₂(C₄H₂O₄)₃·6N₂H_4. The Curie temperature of the ‘as-prepared oxide’ was determined by AC susceptibility measurements.     

Effect of nucleating agents on the crystallization of Li<Subscript>2</Subscript>O-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> system glass

The processes of nucleation of Li₂O-Al₂O₃-SiO₂ glasses with TiO₂ and TiO₂+ZrO₂ as nucleating agents were discussed. The DTA peak temperature and DTA peak height shown a strong dependence on the nucleation temperature in the glass with TiO₂, while in the glass with TiO₂+ZrO₂ this tendency was small. The optimum nucleation temperatures were 745 and 760°C for two glasses. It suggested that with TiO₂+ZrO₂ as nucleating agents, the crystallization had lower sensitivity for nucleation temperature, and the glass had higher nucleation efficiency than with TiO₂.     

Synthesis and magnetic properties of a new layered oxide La<Subscript>1.5</Subscript>Sr<Subscript>1.5</Subscript>Mn<Subscript>1.25</Subscript>Ni<Subscript>0.75</Subscript>O<Subscript>6.67</Subscript>

A new oxide phase La_1.5Sr_1.5 Mn_1.25Ni_0.75O_{6.67 ± 0.05}, a member of the A_{n + 1} BnO_3n+1(n=2) Rad-dlesden—Popper homologue series, was synthesized, and its structure and magnetic properties characterized. Magnetic anomalies associated with the competition between antiferromagnetic and ferromagnetic orders are observed in the range of the temperatures studied (2-400 K). The ESR spectra of the compound feature the constriction of a magnetic signal and a shift toward g(Mn⁴⁺).