Phenylboronic acid-functionalized cross-linked chitosan magnetic adsorbents for the magnetic solid-phase extraction of benzoylurea pesticides

In this study, a 4-formylphenylboronic acid-modified cross-linked chitosan magnetic nanoparticle (FPBA@CCHS@Fe₃O₄) was fabricated. The synthesized material was utilized as the magnetic solid-phase extraction adsorbent for the enrichment of six benzoylurea pesticides. In addition to B-N coordination, FPBA@CCHS@Fe₃O₄ interacts with benzoylureas through hydrogen bonds and π-π stacking interaction on account of rich active groups (amino and hydroxyl) and aromatic rings in structure. Compared to traditional extraction methods, less adsorbent (20 mg) and reduced extraction time (3 min) were achieved. The adsorbent also exhibited good reusability (no less than 10 times). Coupled with a high-performance liquid chromatography–diode array detector, satisfactory recoveries (89.1–103.9%) and an acceptable limit of detection (0.2–0.7 μg/L) were obtained. Under optimized conditions, the established method was successfully applied to the tea infusion samples from six major tea categories with acceptable recoveries ranging from 76.8 to 110%, indicating its application potential for the quantitative detection of pesticides in complex matrices.     

Metal-organic framework derived magnetic nanoporous carbon as an adsorbent for the magnetic solid-phase extraction of chlorophenols from mushroom sample

In this work, a metal-organic framework derived nanoporous carbon(MOF-5-C) was fabricated and modified with Fe_3O_4 magnetic nanoparticles. The resulting magnetic MOF-5-derived porous carbon(Fe_3O_4@MOF-5-C) was then used for the magnetic solid-phase extraction of chlorophenols(CPs) from mushroom samples prior to high performance liquid chromatography–ultraviolet detection. Scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and N_2 adsorption were used to characterize the adsorbent. After experimental optimization, the amount of the adsorbent was chosen as 8.0 mg, extraction time as 10 min, sample volume as 50 m L, desorption solvent as 0.4 m L(0.2 mL×2)of alkaline methanol, and sample p H as 6. Under the above optimized conditions, good linearity for the analytes was obtained in the range of 0.8–100.0 ng g~(-1)with the correlation coefficients between0.9923 and 0.9963. The limits of detection(S/N = 3) were in the range of 0.25–0.30 ng g~(-1), and the relative standard deviations were below 6.8%. The result showed that the Fe3O4@MOF-5-C has an excellent adsorption capacity for the analytes.     

Evaluation of a magnetic polysulfone microcapsule containing organic modified montmorillonite as a novel solid-phase extraction sorbent with chlorophenols as model compounds

A porous polysulfone microcapsule containing organic modified montmorillonite and magnetic nanoparticles (OMMT-Fe₃O₄@PSF) has been successfully prepared by a phase-inversion method and evaluated as a magnetic solid-phase extraction (MSPE) sorbent for clean-up and enrichment of 4-chlorophenol (4-CP) and 2-chlorophenol (2-CP) in aqueous samples. Compared with a microcapsule containing the conventional extraction sorbent C18 (C18-Fe₃O₄@PSF), OMMT-Fe₃O₄@PSF had much lower cost, a faster adsorption rate, and superior uptake amounts for the investigated analytes. The proposed microcapsule has been developed for the extraction of 4-CP and 2-CP from environmental water samples and their analysis by high-performance liquid chromatography with UV detection (HPLC-UV). Various parameters, such as pH, extraction time, the mass of sorbent, and the desorption conditions, have been evaluated and the calibration curves of the chlorophenols were linear (R² ≥ 0.9985) in the range from 1.01 to 104.5 ng mL⁻¹. The limits of detection at a signal-to-noise (S/N) ratio of 3 were 0.22 and 0.17 ng mL⁻¹ and the limits of quantification calculated at S/N = 10 were 1.52 and 1.07 ng mL⁻¹ for 2-CP and 4-CP, respectively. The recoveries of 2-CP and 4-CP from natural water and the treated wastewater samples were in the range of 84.4-115% with relative standard deviations (RSDs) lower than 7.0%. The results have demonstrated the suitability of the MSPE approach for the analysis of trace chlorophenols in aqueous samples.     

Sulfhydryl-functionalised magnetic nanoparticles as sorbent in dispersive solid-phase extraction for the rapid enrichment of mercury species from natural water samples

The sulfhydryl-functionalised core-shell Fe₃O₄@SiO₂ magnetic nanoparticles (Fe₃O₄@SiO₂–RSH MNPs)-based dispersive solid-phase extraction method was developed. The goal of this method is the extraction of mercury species from natural water samples. An interesting aspect of the method is that, thanks to the spontaneously aggregate, the MNPs with a sub-30-nm-size range could be fast and efficiently extracted by 0.45 μm pore size mixed cellulose esters membrane filter. Thus, the elution step can be conducted by passing small amounts eluent through the MNPs on the membrane. It is also found that addition of Ag⁺ to water sample could improve the elution efficiency, and furthermore, minimises the matrix effects during the extraction of mercury species from natural water samples. The feasibility of the method was studied, and extraction efficiency was evaluated. The results showed that, calculated at 5 ng/L spiked concentration levels, absolute recoveries were 89.4%, 91.9% and 64.2%, and enrichment factors (EFs) were 596, 613 and 428, for inorganic mercury, methylmercury and ethylmercury, respectively. The high EFs were achieved in 5 min of overall extraction time. The method was applied to groundwater and river water samples. The results showed that its suitability for use in fast extracting trace levels of mercury species from natural water samples.     

Magnetic polyethyleneimine functionalized reduced graphene oxide as a novel magnetic solid-phase extraction adsorbent for the determination of polar acidic herbicides in rice

A novel magnetic polyethyleneimine modified reduced graphene oxide (Fe₃O₄@PEI-RGO) had been fabricated based on a self-assemble approach between positive charged magnetic polyethyleneimine (Fe₃O₄@PEI) and negative charged GO sheets via electrostatic interaction followed by chemical reduction of GO to RGO. The as-prepared Fe₃O₄@PEI-RGO was characterized by transmission electron microscopy (TEM), Fourier transform infrared spectrometry (FT-IR), X-ray diffraction (XRD), thermal gravimetric analyzer (TGA), vibrating sample magnetometer (VSM) and zeta potential analysis, and then was successfully applied to determine four phenoxy acid herbicides and dicamba in rice coupled with high performance liquid chromatography (HPLC). As a surface modifier of RGO, PEI not only effectually affected the surface property of RGO (e.g. zeta potential), but also changed the polarity of RGO and offered anion exchange groups to polar acidic herbicides, which would directly influence the type of adsorbed analytes. Compared with Fe₃O₄@PEI, Fe₃O₄/RGO and Fe₃O₄@PEI-GO, the as-prepared Fe₃O₄@PEI-RGO, integrating the superiority of PEI and RGO, showed higher extraction efficiency for polar acidic herbicides. Besides, the adsorption mechanism was investigated as well. It turned out that electrostatic interaction and π-π interaction were considered to be two major driving force for the adsorption process. Response surface methodology (RSM), a multivariate experimental design technique, was used to optimize experimental parameters affecting the extraction efficiency in detail. Under the optimal conditions, a satisfactory performance was obtained. The calibration curves were linear over the concentration ranging from 2 to 300 ng g⁻¹ with correlation coefficients (r) between 0.9985 and 0.9994. The limits of detection (LODs) were in the range of 0.67–2 ng g⁻¹. The recoveries ranged from 87.41% to 102.52% with relative standard deviations (RSDs) less than 8.94%. Taken together, the proposed method was an efficient pretreatment and enrichment procedure and could be successfully applied for selective extraction and determination of polar acidic herbicides in complex matrices.     

Magnetic solid-phase extraction using Schiff base ligand supported on magnetic nanoparticles as sorbent combined with dispersive liquid-liquid microextraction for the extraction of phenols from water samples

ABSTRACT

In this work, the magnetic sorbent was developed by covalent binding of a Schiff base ligand, N,N’-bis(3-salicyliden aminopropyl)amine (salpr), on the surface of silica coated magnetic nanoparticles (Salpr@SCMNPs). The core-shell nanoparticle was applied for the magnetic solid-phase extraction (MSPE) combined with dispersive liquid-liquid microextraction (DLLME) of phenolic compounds from water samples prior to gas chromatography-flame ionisation detector (GC?FID). Characterisation of the Salpr@SCMNPs was performed with different physicochemical methods such as Fourier transform infrared (FT-IR), scanning electron microscopy (SEM) and vibrating sample magnetometer (VSM). Variables affecting the performance of both extraction steps such as pH of the water sample, the sorbent amount, the desorption conditions, the extraction time; and extraction solvent were studied. Under the optimised conditions, the analytical performances were determined with a linear range of 0.01–100 ng mL^?1 and a limit of detection at 0.003–0.02 ng mL^?1 for all of the analytes studied. The intra-day (n = 5) and inter-day (n = 3) relative standard deviations (RSD%) of three replicates were each demonstrated in the range of 6.9–8.9% and 7.3–10.1%, respectively. The proposed method was executed for the analysis of real water samples, whereby recoveries in the range of 92.9–99.0% and RSD% lower than 6.1% were attained.     

A novel polymeric ionic liquid-coated magnetic multiwalled carbon nanotubes for the solid-phase extraction of Cu,Zn-superoxide dismutase

A novel magnetic adsorbent, benzyl groups functionalized imidazolium-based polymeric ionic liquid (PIL)-coated magnetic multiwalled carbon nanotubes (MWCNTs) (m-MWCNTs@PIL), has been successfully synthesized and applied for the extraction of Cu, Zn-superoxide dismutase (Cu, Zn-SOD). The m-MWCNTs@PIL were characterized by X-ray diffraction (XRD), Fourier transform infrared spectrometry (FT-IR), thermal gravimetric analysis (TGA), field emission scanning electron microscopy (FESEM), vibrating sample magnetometer (VSM) and zeta-potential nanoparticles. In this method, the m-MWCNTs@PIL could interact with Cu, Zn-SOD through hydrogen bonding, π-π and electrostatic interactions. The extraction performance of the m-MWCNTs@PIL in the magnetic solid-phase extraction (MSPE) procedure was investigated, coupled with the determination by UV–vis spectrophotometer. Compared with m-MWCNTs@IL and m-MWCNTs, the m-MWCNTs@PIL exhibited the highest extraction capacity of 29.1 mg/g for Cu, Zn-SOD. The adsorbed Cu, Zn-SOD remained high specific activity after being eluted from m-MWCNTs@PIL by 1 moL/L NaCl solution. Besides, the m-MWCNTs@PIL could be easily recycled and successfully employed in the extraction of Cu, Zn-SOD from real samples. Under the optimal conditions, the precision, repeatability and stability of the proposed method were investigated and the RSDs were 0.29%, 1.68% and 0.54%, respectively. Recoveries were in the range of 82.7–102.3%, with the RSD between 3.47% and 5.35%. On the basis of these results, the developed method has great potential in the extraction of Cu, Zn-SOD or other analytes from biological samples.     

Preparation of magnetic chitosan and graphene oxide-functional guanidinium ionic liquid composite for the solid-phase extraction of protein

A series of novel cationic functional hexaalkylguanidinium ionic liquids and anionic functional tetraalkylguanidinium ionic liquids have been synthesized, and then magnetic chitosan graphene oxide (MCGO) composite has been prepared and coated with these functional guanidinium ionic liquids to extract protein by magnetic solid-phase extraction. MCGO-functional guanidinium ionic liquid has been characterized by vibrating sample magnetometer, field emission scanning electron microscopy, X-ray diffraction spectrometer and Fourier transform infrared spectrometer. After extraction, the concentrations of protein were determined by measuring the absorbance at 278 nm using an ultra violet visible spectrophotometer. The advantages of MCGO-functional guanidinium ionic liquid in protein extraction were compared with magnetic chitosan, graphene oxide, MCGO and MCGO-ordinary imidazolium ionic liquid. The proposed method has been applied to extract trypsin, lysozyme, ovalbumin and bovine serum albumin. A comprehensive study of the adsorption conditions such as the concentration of protein, the amount of MCGO-functional guanidinium ionic liquid, the pH, the temperature and the extraction time were also presented. Moreover, the MCGO-functional guanidinium ionic liquid can be easily regenerated, and the extraction capacity was about 94% of the initial one after being used three times.     

Magnetic graphene oxide modified with choline chloride-based deep eutectic solvent for the solid-phase extraction of protein

Four kinds of green deep eutectic solvents (DESs) based on choline chloride (ChCl) have been synthesized and coated on the surface of magnetic graphene oxide (Fe₃O₄@GO) to form Fe₃O₄@GO-DES for the magnetic solid-phase extraction of protein. X-ray diffraction (XRD), vibrating sample magnetometer (VSM), Fourier transform infrared spectrometry (FTIR), field emission scanning electron microscopy (FESEM) and thermal gravimetric analysis (TGA) were employed to characterize Fe₃O₄@GO-DES, and the results indicated the successful preparation of Fe₃O₄@GO-DES. The UV–vis spectrophotometer was used to measure the concentration of protein after extraction. Single factor experiments proved that the extraction amount was influenced by the types of DESs, solution temperature, solution ionic strength, extraction time, protein concentration and the amount of Fe₃O₄@GO-DES. Comparison of Fe₃O₄@GO and Fe₃O₄@GO-DES was carried out by extracting bovine serum albumin, ovalbumin, bovine hemoglobin and lysozyme. The experimental results showed that the proposed Fe₃O₄@GO-DES performs better than Fe₃O₄@GO in the extraction of acidic protein. Desorption of protein was carried out by eluting the solid extractant with 0.005 mol L⁻¹ Na₂HPO₄ contained 1 mol L⁻¹ NaCl. The obtained elution efficiency was about 90.9%. Attributed to the convenient magnetic separation, the solid extractant could be easily recycled.     

Polyaniline-coated Fe(3) O(4) nanoparticles: An anion exchange magnetic sorbent for solid-phase extraction

In this study, the capability of the prepared polyaniline-coated Fe(3) O(4) nanoparticles for magnetic solid-phase extraction of three parabens from environmental wastewater, cream, and toothpaste samples is presented. Synthesized Fe(3) O(4) nanoparticles were coated with sulfate-doped polyaniline via polymerization of aniline in the presence of Fe(3) O(4) nanoparticles and sulfuric acid. Here, polyaniline-coated Fe(3) O(4) nanoparticles are presented as anion exchange sorbent, which extract anionic form of parabens via anion exchange with dopant of polyaniline. The experimental conditions affecting extraction efficiency were further studied and optimized. The experimental results showed that maximum extraction efficiency can be obtained at 70 mL sample solution of pH 8, extraction and desorption times of 2 and 1 min, respectively, 100 μL of 3% (v/v) acetic acid in acetonitrile as eluent, and 100 mg of the adsorbent. Under these conditions, the linear dynamic ranges were 0.5-100 μg/L with good correlation coefficients (0.998-0.999). The detection limits were in the range of 0.3-0.4 μg/L and the relative standard deviations were less than 2.4 (n = 5) for the three parabens. Finally, this fast and efficient method was further employed for determination of target analytes in cream, toothpaste, and environmental wastewater samples and satisfactory results were obtained.     

Novel thionin-functionalised core shell magnetic nanoparticles for dispersive solid-phase extraction of Hg(II) in food and water samples

To develop an accurate and precise method for separation and pre-concentration of Hg(II), a novel thionin functionalised core shell structure magnetic material has been prepared and characterised. The extraction ability of the material was evaluated by magnetic solid-phase extraction coupled with inductively coupled plasma mass spectrometry determination of Hg(II) in food and water samples. Combining the advantages of magnetic separation with selective extraction of thionin towards Hg(II), the material exhibits enhanced enrich selectivity and efficiency for Hg(II). The experimental parameters influencing Hg(II) extraction efficiency, including pH of the aqueous solution, the dosage of the adsorbent, extraction time and sample volume, were systematically investigated. Under the optimised conditions, concentration of Hg(II) at 1.0 μg L^?1 can be successfully enriched by the material without the interference of the common co-existing ions. The enrichment factor and adsorption capacity were 250 and 75.2 mg g^?1, and precise of the method was confirmed by analysing the spiked food, water samples and standard water reference samples with the recoveries of 92.5–101.8%.     

Microwave‐assisted preparation of magnetic nanoparticles modified with graphene oxide for the extraction and analysis of phenolic compounds

Here in, magnetic nanoparticles combined with graphene oxide adsorbent were fabricated via a microwave‐assisted synthesis method, and used in the solid‐phase extraction of three phenolic compounds (phenol, 4‐nitrophenol, and m‐methylphenol) in environmental water samples. Various instrumental methods were employed to characterize the magnetic nanoparticles modified with graphene oxide. The influence of experimental parameters, such as desorption conditions, amount of adsorbent, extraction time, and pH, on the extraction efficiency was investigated. Owing to the high surface area and excellent adsorption capacity of the prepared material, satisfactory extraction was achieved. Under optimum conditions, a linear response was observed in the concentration range of 1.000–100.0 μg/L for phenol, 0.996–99.6 μg/L for 4‐nitrophenol, and 0.975–97.5 μg/L for m‐methylphenol, with correlation coefficients in the range of 0.9995–0.9997. The limit of detection (signal‐to‐noise ratio of 3) of the method varied between 0.5 and 0.8 μg/L. The relative standard deviations were <5.2%. The recovery percentages of the method were in the range of 89.1–104.3%. The results indicate that the graphene oxide‐modified magnetic nanoparticles possess high adsorptive abilities toward phenolic compounds in environmental water samples.     

Tuning of the vinyl groups’ spacing at surface of modified silica in preparation of high density imprinted layer-coated silica nanoparticles: A dispersive solid-phase extraction materials for chlorpyrifos

This paper reports the preparation of high density imprinted layer-coated silica nanoparticles toward selective recognition and fast enrichment of chlorpyrifos (CP) from complicated matrices. The molecularly imprinted polymers (MIPs) were successfully coated at the surface of modified silica through using the chemical immovable vinyl groups at the nanoparticles’ surface, followed by the graft copolymerization of methacrylic acid (MAA) and ethylene glycol dimethacrylate (EGDMA) in the presence of templates CP. It has been demonstrated that the space of end vinyl groups at the surface of silica can be controlled by changing the condition of chemical modification, regulating the thickness of imprinted shells and the density of efficient imprinted sites. After removal of templates by solvent extraction, the recognition sites of CP were created in the polymer coating layer. The CP-imprinted nanoparticles exhibited high recognition selectivity and binding affinity to CP analyte. When the CP-imprinted nanoparticles were used as dispersive solid-phase extraction (dSPE) materials, the high recovery yields of 76.1-93.5% from various spiked samples with only 1 μg/mL analyte were achieved by one-step extraction. These results reported herein provide the possibility for the separation and enrichment of CP from complicated matrices by the molecular imprinting modification at the surface of common silica nanoparticles.     

Fe3O4 nanoparticles as the adsorbent of magnetic solid-phase extraction for clean and preconcentration of maltol and ethyl maltol in food samples followed by HPLC analysis

In this work, a magnetic solid-phase extraction protocol followed with high-performance liquid chromatography analysis was developed for the determination of maltol and ethyl maltol in food samples. The Fe₃O₄ nanoparticles were prepared by one-step hydrothermal method and was used as adsorbent for clean and preconcentrated maltol and ethyl maltol in food samples. The as-prepared Fe₃O₄ nanoparticle was characterized by transmission electron microscope, Fourier transform infrared spectroscopy, X-ray diffraction, and vibrating sample magnetometer. The extraction conditions including the amount of material, extraction time, pH, temperature, and desorption solvents were investigated, respectively. Under the optimized conditions, the detection limits of 0.04 and 0.05?µg?mL^?1 could be achieved for maltol and ethyl maltol. The recoveries between 84.2 and 103.4% with RSDs lower than 2.30% were obtained for the analysis of spiked plum candy sample. The developed method was successfully applied to the analysis of real samples, such as juice, chocolate, and plum candy.     

Monodisperse silica nanoparticles coated with gold nanoparticles as a sorbent for the extraction of phenol and dihydroxybenzenes from water samples based on dispersive micro‐solid‐phase extraction: Response surface methodology

A selective and sensitive method was developed based on dispersive micro‐solid‐phase extraction for the extraction of hydroquinone, resorcinol, pyrocatechol and phenol from water samples prior to high‐performance liquid chromatography with UV detection. SiO₂, SiO₂@MPTES, and SiO₂@MPTES@Au nanoparticles (MPTES = 3‐mercaptopropyltriethoxysilane) were synthesized and characterized by scanning electronic microscopy, thermogravimetric analysis, differential thermogravimetric analysis, and infrared spectroscopy. Variables such as the amount of sorbent (mg), pH and ionic strength of sample the solution, the volume of eluent solvent (μL), vortex and ultrasonic times (min) were investigated by Plackett–Burman design. The significant variables optimized by a Box–Behnken design were combined by a desirability function. Under optimized conditions, the calibration graphs of phenol and dihydroxybenzenes were linear in a concentration range of 1–500 μg/L, and with correlation coefficients more than 0.995. The limits of detection for hydroquinone, resorcinol, pyrocatechol, and phenol were 0.54, 0.58, 0.46, and 1.24 μg/L, and the limits of quantification were 1.81, 1.93, 1.54, and 4.23 μg/L, respectively. This procedure was successfully employed to determine target analytes in spiked water samples; the relative mean recoveries ranged from 93.5 to 98.9%.     

Construction of a portable sample preparation device with a magnetic poly(methacrylic acid‐co‐ethylene dimethacrylate) monolith as the extraction medium and its application in the enrichment of UV filters in water samples

A portable sample preparation device with a magnetic polymer monolith as the extraction medium was constructed. The monolith was synthesized by polymerizing methacrylic acid and ethylene dimethacrylate around a cylindrical magnet. In this way, the monolith with a magnetic core could be readily attached to the extraction device by magnetism. The constructed device was evaluated for the enrichment of UV filters in water samples, followed by high‐performance liquid chromatographic analysis. The extraction efficiency for the targets was satisfactory with no matrix interference. Good linearities were obtained for the UV filters with the correlation coefficients >0.9986. The limits of detection and quantification for the UV filters were 0.3–0.8 and 1.0–2.4 ng/mL, respectively. The recoveries of the UV filters from the spiked water samples at the concentration of 100 ng/mL were 95.3–101.7%, with relative standard deviations <10%. Accordingly, the proposed portable device was demonstrated to be suitable for on‐site simultaneous sampling, purification, and preconcentration within a single step.     

Preparation of highly hydrophilic magnetic nanoparticles with anion‐exchange ability and their application for the extraction of non‐steroidal anti‐inflammatory drugs in environmental samples

Diallyldimethylammonium chloride modified magnetic nanoparticles were synthesized by the “thiol‐ene” click chemistry reaction. Diallyldimethylammonium chloride rendered the material plenty of quaternary ammonium groups, and thus the excellent aqueous dispersibility and anion‐exchange capability. The novel material was then used as the magnetic solid‐phase extraction sorbent to extract eight non‐steroidal anti‐inflammatory drugs from water samples. Combined with high‐performance liquid chromatography and ultraviolet detection, under the optimal conditions, the developed method exhibited wide linearity ranges (1–1000, 2–1000, and 5–1000 ng/mL) with recoveries of 88.0–108.6% and low limits of detection (0.3–1.5 ng/mL). Acceptable precision was obtained with satisfactory intra‐ and inter‐day relative standard deviations of 0.4–4.4% (n = 3) and 1.1–5.5% (n = 3), respectively. Batch‐to‐batch reproducibility was acceptable with relative standard deviations <9.7%. The hydrophilic magnetic nanoparticle featured with quaternary ammonium groups showed high analytical potential for acidic analytes in environmental water samples.     

Computational design and fabrication of core–shell magnetic molecularly imprinted polymer for dispersive micro‐solid‐phase extraction coupled with high‐performance liquid chromatography for the determination of rhodamine 6G

A novel core–shell magnetic nano‐adsorbent with surface molecularly imprinted polymer coating was fabricated and then applied to dispersive micro‐solid‐phase extraction followed by determination of rhodamine 6G using high‐performance liquid chromatography. The molecularly imprinted polymer coating was prepared by copolymerization of dopamine and m‐aminophenylboronic acid (functional monomers), in the presence of rhodamine 6G (template). The selection of the suitable functional monomers was based on the interaction between different monomers and the template using the density functional theory. The ratios of the monomers to template were further optimized by an OA₉ (3⁴) orthogonal array design. The binding performances of the adsorbent were evaluated by static, kinetic, and selective adsorption experiments. The results reveal that the adsorbent possesses remarkable affinity and binding specificity for rhodamine 6G because of the enhanced Lewis acid‐base interaction between the B(Ш) embedded in the imprinted cavities and the template. The nano‐adsorbent was successfully applied to dispersive micro‐solid‐phase extraction coupled to high‐performance liquid chromatography for the trace determination of rhodamine 6G in samples with a detection limit of 2.7 nmol/L. Spiked recoveries ranged from 93.0–99.1, 89.5–92.7, and 86.9–105% in river water, matrimony vine and paprika samples, respectively, with relative standard deviations of less than 4.3%.     

Ionic‐liquid‐modified magnetic nanoparticles as a solid‐phase extraction adsorbent coupled with high‐performance liquid chromatography for the determination of linear alkylbenzene sulfonates in water samples

Novel ionic‐liquid‐functionalized Fe₃O₄ magnetic nanoparticles were synthesized by the thiol‐ene click reaction. The prepared functionalized Fe₃O₄ nanoparticles possessed multiple interactions, such as electrostatic, hydrophobic, and π–π interactions. The functionalized Fe₃O₄ nanoparticles were characterized by using Fourier transform infrared spectroscopy, X‐ray diffraction, vibrating sample magnetometry, and transmission electron microscopy. Four kinds of linear alkylbenzene sulfonates, namely, sodium decylbenzenesulfonate, sodium undecylbenzene sulfonate, sodium dodecylbenzenesulfonate, and sodium tridecylbenzenesulfonate, were selected as model compounds to evaluate the applicability of adsorbents for extraction and subjected to high‐performance liquid chromatography analysis. In addition, the effects of various parameters, such as sorbent amount, pH value, ionic strength, sample volume, extraction time, and elution conditions on extraction efficiency were studied in detail. Under the optimum conditions, good linearities were attained, with correlation coefficients between 0.9912 and 0.9968. The proposed method exhibited limits of detection ranging from 0.061 to 0.099 μg/L for all the target analytes. The spiked recoveries of the target analytes in real water samples ranged from 86.3 to 107.5%, with relative standard deviations lower than 7.96%. The enrichment factors of the analytes ranged from 364 to 391, indicating that the obtained functionalized Fe₃O₄ nanoparticles can effectively extract trace target analytes from environmental water samples.