苯乙烯－乙烯共聚物的合成及其结构性能的研究

用负载型钛系催化剂ＭｇＣｌ_２／ＴｉＣｌ_４，ＮｄＣｌ_３／ＡｌＥｔ_３（ＳＮ－１催化剂）制备出组份比例变化的苯乙烯－乙烯共聚产物．共聚产物通过溶剂萃取分离、~１３Ｃ－ＮＭＲ、ＩＲ、动态粘弹谱进行表征，并初步进行了与聚苯乙烯（ａＰＳ）共混作用的研究．结果表明，ＳＮ－１催化剂能有效地催化苯乙烯与乙烯共聚合．共聚产物为含有均聚聚苯乙烯的共聚物复合物，其中的２５ｍｏｌ％的苯乙烯参加了共聚．共聚产物与ａＰＳ共混可明显提高ａＰＳ的冲击强度和断裂伸长率．     

苯乙烯－乙烯共聚物的合成及其结构性能的研究

用负载型钛系催化剂ＭｇＣｌ２／ＴｉＣｌ４，ＮｄＣｌ３／ＡｌＥｔ３（ＳＮ－１催化剂）制备出组份比例变化的苯乙烯－乙烯共聚产物，共聚产物通过溶剂萃取分离，＾１３Ｃ－ＮＭＲ，ＩＲ，动态粘弹谱进行表征，并初步进行了与聚苯乙烯共混作用的研究。结果表明，ＳＮ－１催化剂能有效地催化苯乙烯与乙烯共聚合，共聚产物为含有均聚聚苯乙烯的共聚复合物，其中约２５ｍｏｌ％的苯乙烯参加了共聚。共聚产物与ａＰＳ共混可明显提高ａＰ     

高密度聚乙烯与乙烯丙烯辛烯－1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性．     

高密度聚乙烯与乙烯丙烯辛烯—1共聚物共混体系的相容性

用ＤＳＣ和ＷＡＸＤ方法研究了高密度聚乙烯／聚（乙烯丙烯辛烯－１）（ＨＤＰＥ／ＥＰＯ）共混体系的结晶性能。共混物的ＤＳＣ曲线皆呈单峰，表明共混体系形成了共晶。晶胞参数ａ及结晶度随共混物组成而变，进一步证明ＨＤＰＥ／ＥＰＯ共混体系的相容性。     

负载型贵金属催化剂的制备化学－载体等电点对Pd／A1_2O_3催化剂结构与催化性能的影响

本文通过化学修饰的方法改变了γ－Ａｌ_２Ｏ_３载体等电点（ＩＥＰＳ），并用具有不同等电点的Ａｌ_２Ｏ_３作载体，以（ＮＨ_４）_２ＰｄＣｌ４为活性组分前身制备了一系列Ｐｄ／Ａｌ_２Ｏ_３催化剂，在固定床微反色谱装置上考察了其对ＣＯ氧化的催化活性，用Ｈｉ—Ｏ_２滴定、紫外漫反射光谱（ＤＲＳ）、透射电子显微镜（ＴＥＭ）中的能量色散谱（ＥＤＸＳ）等方法对上述催化剂进行了表征，结果表明：Ａｌ_２Ｏ_３的等电点（ＩＥＰＳ）对所得催化剂中金属分散度和浓度分布都有明显影响，ＩＥＰＳ越高。活性组分越靠近外表面，在相同担载量下，其分散度也越高。这主要是由于载体ＩＥＰＳ的改变，导致了（ＮＨ_４）_２ＰｄＣｌ_４在γ－Ａｌ_２Ｏ_３上吸附机理的变化，并使所得催化剂对ＣＯ氧化的催化活性发生了规律性的变化。     

二苯醚—对苯二甲酰氯—4,4‘—二苯氧基二苯砜三元共聚物的合成与性能

以无水ＡｌＣｌ３／ＣｌＣＨ２ＣＨ２Ｃｌ／ＮＭＰ为催化剂／溶剂体系，通过缩聚反应，由二苯醚，对苯二甲酰氯和４，４－二苯氧基二苯砜合成了聚醚酮酮和聚醚砜醚酮酮共聚物（ＰＥＫＫ／ＰＥＳＥＫＫ）．考察了单体浓度、反应时间对聚合物分子量的影响，并对其进行了ＩＲ、ＤＳＣ、ＷＡＸＤ等分析表征．结果表明，共聚物具有优异的耐热性，随着共聚物中ＰＥＳＥＫＫ单元含量的增加，其玻璃化温度逐渐升高，而熔融温度和结晶度逐渐降低．与聚醚酮酮（ＰＥＫＫ）相比，共聚物的断裂伸长率明显提高，而拉伸强度和拉伸模量却有所下降，但仍具有良好的力学性能．     

CS_2在Cu－S键中插入产物（Ph_3P）_2Cu（S_2CSR）与溶剂反应的

ＣＳ_２在Ｃｕ－Ｓ键中插入产物（Ｐｈ_３Ｐ）_２Ｃｕ（Ｓ_２ＣＳＰｈ）与ＣＨ_２Ｃｌ_２－Ｃ_２Ｈ_５ＯＨ混合溶剂反应，获得单核铜配合物（Ｐｈ_３Ｐ）_２Ｃｕ（Ｓ_２ＣＯＯＣ_２Ｈ_５）和双核铜配合物（Ｐｈ_３Ｐ）_３Ｃｕ_２Ｃｌ_２等化合物晶体，用Ｘ－射线单晶衍射法测定前者的晶体结构。晶体的化学式为Ｃ_（３９）Ｈ_（３５）ＣｕＯＰ_２Ｓ_２，分子量为７０９．３，空间群Ｐ２１／ｎ，ａ＝９．３２９（６），ｂ＝１８．６６４（１１），ｃ＝２０，３４１（１３），β＝９５．５９（５）°，Ｖ＝３５２５（４）~３，Ｄ_ｃ＝１．３３７ｇ／ｃｍ~３，Ｚ＝４，Ｆ（０００）＝１４９２，μ＝０．８５２ｍｍ~（－１），Ｒ＝０．０４５。     

AlCl_3／SbCl_3复合体系引发α－蒎烯／苯乙烯阳离子共聚合

比较了ＡｌＣｌ_３和ＡｌＣｌ_３／ＳｂＣｌ_３复合体系的α－蒎烯／苯乙烯阳离子共聚反应及产物的摩尔质量分布。结果表明，由于用ＡｌＣｌ_３体系两种单体活性差大而难以共聚，用ＡｌＣｌ_３／ＳｂＣｌ_３复合体系，苯乙烯聚合速率相对减小，而α－蒎烯聚合速率增大，加之苯乙烯的共催化剂作用，加速α－蒎烯聚合，可使α－蒎烯与苯乙烯进行有效共聚。考察了［Ｓｂ］／［Ａｌ］比、催化剂浓度、单体投料比等对共聚体系α－蒎烯、苯乙烯转化速率及产物Ｍ_ｎ的影响。     

聚氧化乙烯梳状聚合物共混物的非等温结晶动力学

用ＤＳＣ方法对乙烯基甲醚／马来酸酐交替共聚物多缩乙二醇酯（ＣＢＰ） 聚氧化乙烯（ＰＥＯ）共混体系的非等温结晶动力学进行了研究，用Ｍａｎｄｅｌｋｅｒｎ、Ｚ Ｊ（Ｚｉａｂｉｋｉ Ｊｅｚｉｏｒｎｙ）、Ｏｚａｗａ和对Ｏｚａｗａ方法的一种修正方法对该体系进行了处理．结果表明：得到了一种既没有结晶又有较多ＥＯ单元含量的共混物，ＣＢＰ对ＰＥＯ的结晶有抑制作用．Ａｖｒａｍｉ指数随冷却速率的加快在３８～５７之间波动．Ｍａｎｄｅｌｋｅｒｎ方法求得的结晶动力学参数Ｚｃ随冷却速率的增加而增加，共混物的Ｇｃ值不随冷却速率的变化而变化，随ＰＥＯ含量增加而减少，处理结果表明而Ｚ Ｊ理论能较好地解释本体系的非等温结晶过程和机理．     

与甲醇合成铜基催化剂研究有关的ZnO和ZnO－Al_2O_3体系的ESR及XPS表征

本文用ＥＳＲ谱和ＸＰＳ谱对这类催化剂作了表征研究。结果表明，在经Ａｌ￣（３＋）掺杂的ＺｎＯ－Ａｌ_２Ｏ_３体系上，观测到ｇ＝１．９６０６±０．０００２，△Ｈ_（ｐｐ）＝（２．８±０．１）×１０￣（－４）Ｔ的顺磁信号，该信号强度（以自旋数／克表示）随ＺｎＯ中Ａｌ_２Ｏ_３掺杂量增加而增长；当Ａｌ／Ｚｎ达２／１００（原子比）时，逐渐趋于平稳。相关体系的ＥＳＲ和ＸＡＥＳ比较研究结果排除了该顺磁信号系产生于顺磁氧物种（诸如，Ｏ_２－、Ｏ－或Ｏ_３－）或Ｚｎ＋的可能性，而有利于关于三价金属离子（ＡＬ￣（３＋））掺杂在ＺｎＯ晶格中诱导生成正一价缺位的推断。这类Ｓｈｏｔｔｋｙ缺位在催化剂表面富集，有利于表面Ｃｕ￣＋物种的稳定，从而促进了ＣＯ加氢活性的提高。     

Drawing by solid-state coextrusion of blends of atactic and isotactic polystyrene with poly(2,6-dimethyl-1,4-phenylene oxide)

Atactic polystyrene (aPS)/poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) and isotactic polystyrene (iPS)/PPO compatible blends of varied composition were subjected to solid-state coextrusion. The efficiency of drawing, orientation, and crystallinity development were studied as a function of composition and draw ratio. The efficiency of drawing, as measured by elastic recovery, is high for coextrusion at temperatures ?40°C above the glass transition temperature of the particular blend. The maximum attainable draw ratio for the blends decreased with increasing PPO concentration; the highest blend draw ratio attained was 6.5 for 25 wt % PPO. The orientation on drawing, as measured by birefringence, increased with draw but decreased with increasing PPO component at the same draw ratio. When PPO was <50% in iPS/PPO blends, iPS crystallized on draw. The morphology of drawn blends was studied by electron microscopy and wide-angle x-ray scattering.     

Morphology and thermal properties of a PC/PE blend with reactive compatibilization

Reactive compatibilization of immiscible polymers is becoming increasingly important and hence a representative study of a polycarbonate/high density polyethylene (PC/HDPE) system is the focus of this paper. A grafted copolymer PC‐graft‐ethylene‐co‐acrylic acid (PC‐graft‐EAA) was generated as a compatibilizer in situ during processing operation by ester and acid reaction between PC and ethylene‐acrylic acid (EAA) in the presence of the catalyst dibutyl tin oxide (DBTO). As the polyethylene (PE) matrix does not play any part during the synthesis of the copolymer and since PC and EAA are also immiscible, to simplify the system, the influence of this copolymer formation at the interface between PC and EAA on rheological properties, phase morphology, and crystallization behavior for EAA/PC binary blends was first studied. The equilibrium torque increased with the DBTO content increasing in EAA/PC blends on Haake torque rheometer, indicating the in situ formation of the graft copolymer. Scanning electron microscopy (SEM) studies of cryogenically fractured surfaces showed a significant change at the distribution and dispersion of the dispersed phase in the presence of DBTO, compared with the EAA/PC blend without the catalyst. Differential scanning calorimetry (DSC) studies suggested that the heat of fusion of the EAA phase in PC/EAA blends with or without DBTO reduced with the formation of the copolymer compared with pure EAA. Then morphological studies and crystallization behavior of the uncompatibilized and compatibilized blends of PC/PE were studied as functions of EAA phase concentration and DBTO content. Morphological observations in PC/PE blends also revealed that on increasing the EAA content or adding the catalyst DBTO, the number of microvoids was reduced and the interface was intensive as compared to the uncompatibilized PC/PE blends. Crystallization studies indicated that PE crystallized at its bulk crystallization temperature. The degree of crystallinity of PE phase in PC/PE/EAA blends was also reduced with the addition of EAA and DBTO compared to the uncompatibilized blends of PC/PE, indicating the decrease in the degree of crystallinity was more in the presence of PC‐graft‐EAA. Copyright © 2007 John Wiley & Sons, Ltd.     

Thermal expansion of ultradrawn polystyrene

Measurements on the linear thermal expansivities α∥ and α⊥ parallel and perpendicular to the extrusion direction, respectively, have been carried out between ?160 and 30°C for atactic polystyrene (aPS) with extrusion ratio 1 ≤λ≤ 15 and isotactic polystyrene (iPS) with 1 ≤λ≤ 7.5. For both aPS and iPS, α∥ decreases sharply with increasing λ whereas α⊥ shows only a slight increase. Below λ = 5 the anisotropy α⊥/α∥ is nearly the same for both, but α⊥/α∥ for iPS becomes much larger at higher λ. This is accompanied by an abrupt rise in crystallinity and probably results from the increase in the number and tautness of intercrystalline tie molecules. The birefringences of aPS and iPS increase with λ and have nearly the same values for λ < 5. At higher λ, however, there is a sharp rise in the birefringence of iPS which is probably associated with the sudden increase in crystallinity. With an aggregate model, the chain orientation function for aPS calculated from thermal expansivity is found to be in reasonable agreement with the corresponding value obtained from birefringence.     

Morphological and Structural Studies of sPS/aPS Blends

Inrecentyears,thenewsedricrystallinepolymersyndiotacticp0lystyrene(sPS)hasat-ITactedmuchattentionduetoitsg0odchendcalresistanceandenhancedmechanicalperformanceatelevatedtemPeratUre.'H0wever,itexhibitshighbrittlenessandpoorimPact-resistanceandtCar-resistance.2Therefore,itisnecessarytomodifyitwithtougheningpolyIners.AsimPlemeth0dto0verc0methedriscibilityofatwo-phaseblendofsPSandatougheningpolymristotwrovetheinterfacialaffmity,wheretheadditionofablockcoP0lymerisconsideredtobemosteffective.3…     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Phase morphology of iPP/aPS/SEP blends

Supermolecular structure and phase morphology of the ternary isotactic polypropylene/atactic polystyrene/poly(styrene-b-ethylene-co-propylene) (iPP/aPS/SEP) compression molded blends with 100/0, 90/10, 70/30, and 50/50 iPP/aPS weight ratios and with different amounts of added SEP compatibilizer were studied by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), small-angle X-ray scattering (SAXS) and wide-angle X-ray diffraction (WAXD). SEP significantly reduced the size of dispersed aPS particles that enabled better spherulitization in the iPP matrix. Furthermore, iPP spherulites in ternary blends with 90/10 iPP/aPS weight ratio became larger in comparison with the pure iPP. TEM revealed that the SEP formed continuous interface layer around the dispersed aPS particles even when only 2.5 wt.% of SEP was added. Particle size distribution was distinctly bimodal. When the SEP content was increased to 10 wt.%, joining together smaller and bigger aPS and SEP particles formed dispersed aggregates. Additionally, both amorphous components (aPS and SEP) influenced crystallization process of iPP matrix and so modified, to some extent, its final supermolecular structure. SEP compatibilizer did not significantly affect crystallite orientation. The increase of crystallite sizes, which was more affected by the addition of aPS than by the addition of SEP, seemed to be influenced by the solidification effect rather than by the phase morphology of the blends.     

PC/ABS及PC/ABS/PE-g-MAH共混体系相容性的研究

研究了聚碳酸酯与ＡＢＳ（ＰＣ／ＡＢＳ）及ＰＣ／ＡＢＳ与马来酸酐接枝聚乙烯共聚物（ＰＣ／ＡＢＳ／ＰＥ－ｇ－ＭＡＨ）共混体系的力学性能和应力开裂性能。用ＤＳＣ和ＳＥＭ研究了共混体系的相容性。结果表明：ＡＢＳ的加入能提高ＰＣ的冲击强度,ＡＢＳ的含量及品种影响ＰＣ／ＡＢＳ合金的力学性能,ＡＢＳ能提高ＰＣ的耐溶剂应力开裂性能。ＰＣ／ＡＢＳ／ＰＥ－ｇ－ＭＡＨ共混体系的力学性能和相容性优于ＰＣ／ＡＢＳ共混体系,     

Thermal properties and crystalline structure of syndiotactic polystyrene‐based miscible blends

This work examined the effect of the pre‐melting temperature (T_max) on the thermal properties and crystalline structure of four miscible syndiotactic polystyrene (sPS)‐based blends containing 80 wt % sPS. The counterparts for sPS included a high‐molecular‐weight atactic polystyrene [aPS(H)], a medium‐molecular‐weight atactic polystyrene [aPS(M)], a low‐molecular‐weight atactic polystyrene [aPS(L)], and a low‐molecular‐weight poly(styrene‐co‐α‐methyl styrene) [P(S‐co‐αMS)]. According to differential scanning calorimetry measurements, upon nonisothermal melt crystallization, the crystallization of sPS shifted to lower temperatures in the blends, and the shift followed this order of counterpart addition: P(S‐co‐αMS) > aPS(L) > aPS(M) > aPS(H). The change in T_max (from 285 to 315 °C) influenced the crystallization of sPS in the blends to different degrees, depending on the counterpart's molecular weight and cooling rate. The change in T_max also affected the complex melting behaviors of pure sPS and an sPS/aPS(H) blend, but it affected those of the other blends to a lesser extent. Microscopy investigations demonstrated that changing T_max slightly affected the blends' crystalline morphology, but it apparently altered that of pure sPS. Furthermore, the X‐ray diffraction results revealed that the α‐form sPS crystal content in the blends generally decreased with an increase in T_max, and it decreased with a decrease in the cooling rate as well. The blends showed a lower α‐form content than pure sPS; a counterpart of a lower molecular weight more effectively reduced the formation of α‐form crystals. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2798–2810, 2006     

聚(3-羟基丁酸酯)/聚氧化乙烯共混物非晶区相容性的固体核磁共振研究

用固体高分辨核磁共振碳谱方法研究了不同组成比的聚 (3 羟基丁酸酯 ) 聚氧化乙烯共混物的结晶度、非晶区的相容性和分子运动能力 .结果表明聚 (3 羟基丁酸酯 )的结晶度几乎不随组成比变化 ,而聚氧化乙烯的结晶度则随其在共混物中含量的降低而显著降低 .聚氧化乙烯的加入使得聚 (3 羟基丁酸酯 )非晶区的分子运动能力有所增强 .共混物的非晶区表现出一定的相容性 ,相容程度与共混物的组成比有关     

Blends of polycarbonate and ethylene-1-octylene copolymer

The mechanical properties and morphology of polycarbonate/ethylene-1-octylene copolymer (PC/POE) binary blends and PC/POE/ionomer ternary blends were investigated. The tensile strength and elongation at break of the PC/POE blends decreased with increasing the POE content. The impact strength of the PC/POE blends showed less dependence on thickness than that of PC. And the low-temperature impact strength of PC was modified effectively by addition of POE. The morphology of the PC/POE blends was observed by scanning electron microscope. The PC/POE weight ratio had a great effect on the morphology of the PC/POE blends. For the PC/POE (80/20)/ionomer ternary blends, low content (0.25 and 0.5 phr) of ionomer could increase the tensile properties of PC/POE (80/20) blend and had little effect on the impact strength. And 0.5 phr ionomer made the dispersed domain distribute more uniformly and finely than the blend without it. But with high content of ionomer, the degradation of PC made the mechanical properties of the blends deteriorate. Blending PC and ionomer proved the degradation of PC, and the molecular weight decreased with increasing the ionomer content.