Dielectric and conductivity processes in poly(ethylene terephthalate) and poly(ethylene naphthalate) homopolymers and copolymers

Electrical relaxation and conductivity processes in amorphous and semicrystalline poly(ethylene terephthalate) (PET) and poly(ethylene naphthalate) (PEN) homopolymers and certain PET/PEN copolymers have been studied by means of dielectric spectroscopy. Homopolymers and copolymers able to crystallize were subjected to successive thermal runs to investigate the influence of the thermal history upon the morphology and the electrical behavior of the polymeric systems. The morphology of the untreated as well as the heat‐treated specimens was determined by means of Differential Scanning Calorimetry (DSC). All samples exhibit β‐relaxation process, due to local motions of the C?O polar side groups, and α‐relaxation process associated to the glass/rubber transition. In the PEN spectrum an additional, subglass, mode was recorded, most probably attributed to cooperative motions of the naphthalene groups. Finally, the dynamic nature of the crystallization process is expressed via the over glass transition mode and the temperature dependence of dc conductivity recorded in amorphous PET, PEN, and PET/PEN (85/15) (wt/wt) samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3078–3092, 2006     

Electrical Properties Investigation in PA12/PANI Composites

Summary: Volume conducting PA-12 based composites powders were chemically prepared by in situ polymerization and aniline doping at room temperature. These kinds of polyamide / PANI composites were investigated regarding their electrical properties. Their ac and dc electrical properties measured in the frequency range of 10⁻²–10⁷ Hz are reported and the frequency dependence of electrical conductivity was investigated as a function of PANI concentration leading to the determination of the conductivity. The experimental conductivity was found to increase continuously with PANI content and explained by percolation theory with a relatively low percolation threshold of about 0.4 wt.%. The dielectric behavior of various PANI polymer composites has been characterized by the critical frequency ω_c (denoting the crossover from the dc plateau of the conductivity to its frequency dependent ac behaviour). Modelling the conductivity behavior versus volume fraction using Slupkowski approach has revealed that the considered parameters are not sufficient to describe the electrical conductivity behavior.     

Neopenthyl glycol containing poly(propylene terephthalate)s: structure–properties relationships

Poly(propylene/neopenthyl terephthalate) random copolymers (PPT‐PNT) and poly(neopenthyl terephthalate) (PNT) were synthesized and subjected to molecular characterization. Afterwards, the polyesters were examined by TGA, DSC, andX‐ray. The copolymers, which displayed a good thermal stability, at room temperature appeared as semicrystalline materials: the main effect of copolymerization was a lowering in the amount of crystallinity and a decrease of the melting temperature with respect to homopolymer PPT. XRD measurements allowed the identification of the PPT crystalline structure in all cases. Amorphous samples were obtained after melt quenching, with the exception of PPT‐PNT5, and an increment of T_g as the content of NT units is increased was observed due to the effect of the side methylene groups in the polymeric chain. The Wood equation described well T_g‐composition data. Lastly, the presence of a rigid‐amorphous phase was evidenced in the copolymers, whose amount depended on composition and on thermal treatment. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 170–181, 2008     

Ab-initio study of electronic,optical, thermal,and transport properties of Cr4AlB6

Theoretical investigation of different physical parameters of Cr₄AlB₆ have been done within the framework of density functional theory. Cr₄AlB₆ is a no band gap material. Its Cr-3d states contributes the most at the Fermi level. Thermal properties are investigated using quasi-harmonic Debye model as implemented in Gibbs code for different values of pressure and temperature. Study of transport property suggests that its electrical conductivity increases nonlinearly with increase in temperature but the relative change in its value is very low whereas its thermal conductivity increases linearly with the increase in temperature and relative increase in thermal conductivity is very high. The behavior of Cr₄AlB₆ is anisotropic and property is ceramic. It has potential applications in making ceramic capacitors. Its reflectivity is high in low energy region. It suggests that material can be used as coating material for far-infrared radiation. Study of the transport property suggests that because of very high value of thermal conductivity, it can be used for heat sink applications.     

The Effect of Temperature Conditions During Graphene Oxide Synthesis on Humidity Dependence of Conductivity in Thermally Reduced Graphene Oxide

In this work, we study the effect of temperature conditions during graphene oxide (OG) synthesis on the conductivity dependence viewed as a function of ambient humidity after thermal reduction of initial GO. GO samples obtained at various temperatures by the modified Hummers’ method were found to contain different quantitative ratios of oxide groups. The relative content of carboxyl groups in the initial GO suspension is shown to affect the humidity dependence of conductivity after GO reduction 150 °С. A humidity dependence mechanism is proposed to explain the obtained characteristics.     

Electrical properties of carbon black‐filled polymer composites

This work deals with the dielectric properties of conductive composite materials, which consist of thermoplastic polypropylene (PP) matrix filled with carbon black (CB). The CB concentration was systematically varied in a wide range. Our main interest is focused on the investigation of electrical conductivity mechanism and related percolation phenomena in these materials. To study the electrical and dielectric properties of composites we used broadband ac dielectric relaxation spectroscopy (DRS) techniques in a wide temperature range. By measurements of complex dielectric permittivity, ϵ*, the dependence of ac conductivity, σ_ac, and dc conductivity, σ_dc, on the frequency, the temperature and the concentration of the conductive filler was investigated. The behavior of this system is described by means of percolation theory. The percolation threshold, P_C, value was calculated to be 6.2 wt.% CB. Both, dielectric constant and dc conductivity follow power‐law behavior, yielding values for the critical exponents, which are in good agreement with the theoretical ones. Indications for tunneling effect in the charge carriers transport through the composites are presented. The temperature dependence of dc conductivity gives evidence for the presence of positive temperature coefficient (PTC) effect.     

Effects of processing conditions on rheological,thermal, and electrical properties of multiwall carbon nanotube/epoxy resin composites

We report on the effect of processing conditions on rheology, thermal and electrical properties of nanocomposites containing 0.02–0.3 wt % multiwall carbon nanotubes in an epoxy resin. The influence of the sonication, the surface functionalization during mixing, as well as the application of external magnetic field (EMF) throughout the curing process was examined. Rheological tests combined with optical microscopy visualization are proved as a very useful methodology to determine the optimal processing conditions for the preparation of the nanocomposites. The Raman spectra provide evidence for more pronounced effect on the functionalized with hardener compositions, particularly by curing upon application of EMF. Different chain morphology of CNTs is created depending of the preparation conditions, which induced different effects on the thermal and electrical properties of the nanocomposites. The thermal degradation peak is significantly shifted towards higher temperatures by increasing the nanotube content, this confirming that even the small amount of carbon nanotubes produces a strong barrier effect for the volatile products during the degradation. The ac conductivity measurements revealed lower values of the percolation threshold (pc) in the range of 0.03–0.05 wt %. CNTs for the nanocomposites produced by preliminary dispersing of nanotubes in the epoxy resin, compared to those prepared by preliminary functionalization of the nanotubes in the amine hardener. This is attributed to the higher viscosity and stronger interfacial interactions of the amine hardener/CNT dispersion which restricts the reorganization of the nanotubes. The application of the EMF does not influence the pc value but the dc conductivity values (σ_dc) of the nanocomposites increased at about one order of magnitude due to the development of the aforementioned chain structure. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

New double negative and positive temperature coefficients of conductive EPDM rubber TiC ceramic composites

In this paper, we have successfully prepared ethylene-propylene-diene monomer (EPDM)/TiC composites as thermistors, with new double negative and positive temperature coefficients of conductivity (NTCC/PTCC). EPDM composites loaded with 50 phr HAF carbon black and different concentrations of TiC were prepared. This study focuses on the effect of TiC content on the vulcanization process, the network structure and the electrical and thermal properties of EPDM/TiC composites. The effect of TiC on the network structure was evaluated e.g. the curing process, the characteristic time constant during vulcanization, the volume fraction of rubber, gel fraction, interparticle distance between conductive particles, the extent of TiC reinforcement in the rubber matrix and molecular weight between cross-linking through experimental and affine-phantom models. The effects of TiC content on the percolation theory, electrical conductivity, conducting mechanism of conductivity, conducting hysteresis and I-V characteristics were also studied, as well as its TiC on the (NTCC/PTCC), thermoelectric power, dielectric constant and thermal conductivity. Stability and reproducibility of the thermal cycles for heating element applications was tested. Specific heat and the amount of heat transfer by radiation and convection as a function of TiC content was calculated using both the calorimetric technique and a theoretical model. It was proved that TiC improves the network structure, electrical and thermal properties of EPDM composites for practical applications.     

D.C. electrical conductivity and conduction mechanism of some azo sulfonyl quinoline ligands and uranyl complexes

Supramolecular coordination of dioxouranium(VI) heterochelates 5-sulphono-7-(4'-X phenylazo)-8-hydroxyquinoline HL(n) (n=1, X=CH(3); n=2, X=H; n=3, X=Cl; n=4, X=NO(2)) have been prepared and characterized with various physico-chemical techniques. The infrared spectral studies showed a monobasic bidentate behavior with the oxygen and azonitrogen donor system. The temperature dependence of the D.C. electrical conductivity of HL(n) ligands and their uranyl complexes has been studied in the temperature range 305-415 K. The thermal activation energies E(a) for HL(n) compounds were found to be in the range 0.44-0.9 eV depending on the nature of the substituent X. The complexation process decreased E(a) values to the range 0.043-045 eV. The electrical conduction mechanism has been investigated for all samples under investigation. It was found to obey the variable range hopping mechanism (VRH).     

LaSrMnCoO6: a new cubic double perovskite oxide

Single-phase polycrystalline powder samples of the double perovskite oxide LaSrMnCoO₆ were synthesized by the Pechini (citrate-gel) technique. The structural, magnetic and electrical properties of the obtained powders were investigated by X-ray diffraction, electron microscopy, dc magnetization, ac susceptibility and dc resistivity measurements. The crystal structure of the new compound was found to be cubic of space group at room temperature. Below 225 K, the samples exhibit ferrimagnetic behavior with a spin-glass-like character. Resistivity measurements indicate semiconducting behavior with two different conductivity mechanisms: thermally activated behavior below 190 K and variable range hopping above 190 K.     

Effect of water release on thermal properties of polyaniline

Conducting polyaniline (PANI) was studied by thermal expansion measurement, thermogravimetric analysis and by electrical conductivity measurement. Relative elongation and coefficient of thermal expansion (CTE) were determined from room temperature to 60 °C. Various temperature profiles were used. During heating, the treatment of samples at a constant temperature higher than the room temperature, or evacuation, water was released from the samples. Water release was detected by mass and thermogravimetric analysis. Water release was connected with shrinkage of the PANI samples and apparent negative CTE in the first thermal cycle. In the following thermal cycles, it increased and reached a positive value. CTE of PANI attained values in the range of ?30 × 10^?6 K^?1 up to 20 × 10^?6 K^?1 in dependence on water content in the sample before measurement and on experimental conditions of measurement. Irreversible shrinkage of the polymer was the largest in the first thermal cycle. Water release exhibited a strong time and temperature dependence, and it was only partially reversible. The electrical conductivity was measured by a four-point van der Pauw method. Relative electrical conductivity decreased with amounts of water release. Relative decrease of electrical conductivity reached as far as 20% after evacuation 7 h at the room temperature.     

Simulation of Electrical and Thermal Behavior of Poly(propylene) / Carbon Filler Conductive Polymer Composites

PP-carbon CPC show interesting thermo-electrical properties, smooth resistivity increase with temperature up to 150°C and consequently high power dissipation on a wide temperature range. The addition of short carbon fibers to PP already formulated with carbon black increases sharply the electrical conductivity of the CPC but does not have much influence on thermal conductivity as it could have been expected from the favorable aspect ratio of the fibers. The simulations of the thermo-electrical behavior of the CPC under tension put into evidence a temperature gradient at high heat flux due to the low thermal conductivity, which may damage the material itself.     

Conducting polymers VIII: Optical and electrical conductivity of poly(bis-m-phenylenediaminosulphoxide)

Poly(bis-m-phenylenediaminosulphoxide) (PPDS) was prepared from Michael addition of N,N′-bis-sulphinyl-m-phenylenediamine and m-phenylenediamine. The prepared PPDS was then doped with iodine. PPDS was characterized by FTIR, ¹H-NMR, elemental microanalysis, thermogravimetric analysis (TGA), UV-visible absorption and fluorescence emission spectra. Thermal gravimetric analysis TGA showed that PPDS is thermally stable up to 179 °C. Electronic transitions showed main absorption peak at λ = 340 nm and two emission peaks at 460 and 490 nm. The behavior of both dc and ac electrical conductivities of PPDS were studied. The direct current electrical conductivity (σ_dc) and the alternating current electrical conductivity (σ_ac) were enhanced by the physical doping of I₂ in the polymer matrix. The conduction mechanisms for dc and ac electrical conductivities have been investigated.     

Significant enhancement of electrical and thermal conductivities of polyethylene carbon nanotube composites by the addition of a low amount of silver nanoparticles

Electrically and thermally conductive high‐density polyethylene composites filled with hybrid fillers, multiwall carbon nanotubes (MWCNTs) and silver nanoparticles (Ag‐NPs), have been prepared in the melt state. The investigation of their electrical and thermal conductivities while comparing with high‐density polyethylene/MWCNT binary composites shows that the addition of only 3 vol% of Ag‐NPs does not reduce the electrical percolation threshold (P_c) that remains as low as 0.40 vol% of MWCNTs but leads to an increase in the maximum dc electrical conductivity of PE/MWCNT composites by two orders of magnitudes. Moreover, the association of both Ag‐NPs and carbon nanotube particles improved our composite's thermal conductivity. Copyright © 2014 John Wiley & Sons, Ltd.     

Physical properties of CdS-poly (vinyl alcohol) nanoconducting composite synthesized by organosol techniques and novel application potential

A nanocomposite of poly (vinyl alcohol) (PVA) reinforced with various contents of CdS was synthesized by organosols reaction with particle size in the range of nanoscale. The influence of CdS content on the network structure of PVA matrix such as particle size distribution, gel fraction (GF), equilibrium water content (EWC), water absorption (WA), extent of filler reinforcement (γ), volume fraction of polymer (V_s) number of elastically effective chains (NEC), and X-ray diffraction (XRD) were investigated. The affine and phantom models for physical crosslinks were used to predict the nature of crosslinks. The thermal behavior of PVA-CdS composites has been studied by differential thermal analysis (DTA), Thermogravimetry (TG) and differential scanning calorimetry (DSC). The dc conductivity of the PVA system reinforced with CdS as a function of concentration and temperature has been presented. The PVA composite exhibits considerably high electronic conductivity which increases linearly with the increase of CdS content. The conduction mechanism in PVA-CdS composites is governing by hopping mechanism. The effects of CdS loading and temperature on the thermal conductivity (λ) and specific heats (C_p) were investigated. The antistatic properties and electromagnetic wave shielding effectiveness (EMI) of PVA-CdS composites has been also investigated. The optical properties such as absorbance and transient photo current under applied voltage of PVA-CdS composites were tested. The mechanical properties of PVA-CdS composites were investigated in details. It is proved that the PVA-CdS composites can be effectively used for linear thermistors, antistatic charge dissipation, EMI in the encapsulation of electronic devices, in woven texturing, optical switch and solar cell fabrication.     

Effects of organic-inorganic hybrid coatings on durability of cross-linked polyethylene

Cross-linked polyethylene (XLPE) films have been coated with nanostructured hybrid organic-inorganic coatings in order to improve their durability. For this purpose, bi- and mono-layer coatings containing different amount of silica and different organic polymers have been prepared through sol-gel reactions and applied to XLPE commercial films. The thermo-oxidative stability, electrical strength and conductivity of XLPE coated films have been investigated after ageing in air at temperatures above the on-service conditions, i.e. at 105 and 120 °C for 1900 and 600 h, respectively. The performed investigations (FT-IR, DSC, TGA and electrical properties) showed that all the coatings tested were able to strongly protect XLPE against oxidation, and that the coating with a PVOH/SiO₂ layer gave the best protection. The increase of thermal resistance induced by the coatings reflects on the electrical strength after ageing, which is higher for coated samples than for uncoated ones. Moreover, while ageing has only a slight effect on electrical conductivity in different coated samples, a strong increase of conductivity was observed after ageing for highly oxidated uncoated samples.     

Effects of omega-functional groups on pH-dependent reductive desorption of alkanethiol self-assembled monolayers

Self-assembled monolayers (SAMs) of alkanethiols having various terminal groups on their omega-positions were formed on a Au111 electrode, and their reductive desorption was studied by linear sweep voltammetry, focusing on effects of solution pH on the desorption behavior. The peak potentials (Ep) of cathodic waves representing reductive desorption were found to be reflected by the pKa value of the thiol group and were negatively shifted with an increase in pH of the electrolyte solution. The magnitude of the pH dependency of Ep was greatly influenced by the hydrophobicity of the terminal groups. In the cases of alkanethiol SAMs having pH-sensitive terminal groups such as carboxyl and amino groups, their basicity was estimated from bending points appearing in the pH titration profile of Ep. This method allows direct determination of not only the pKa value of the arrayed groups but also that of the groups dissolved in solution simultaneously. The pKa values of the arrayed carboxyl groups in SAMs were larger by ca. 3 pH units than their original ones, while those for amino groups were smaller by ca. 2 pH units.     

Amphiphilic protic anionic oligomeric ionic liquids of hyperbranched structure

The method of synthesizing anionic amphiphilic protic hyperbranched ionic liquids with the controlled ratio between hydrophilic ionic-liquid groups and hydrophobic alkyl urethane fragments in the oligoester nucleus shell is developed. These compounds are synthesized by the interaction of excess hyperbranched polyesterpolyol containing 32 terminal hydroxyl groups with n-octadecyl isocynate followed by the acylation of hydroxyl groups by phthalic anhydride or 2-sulfobenzoic anhydride and the neutralization of the formed carboxyl or sulfonic groups by N-methylimidazole or 1,2,4-1H-triazole. With a rise in the content of alkyl urethane fragments, the synthesized compounds form the crystalline phase. Structuring of the system leads to different effects of the degree of ionicity of ionic-liquid groups on proton conductivity, which is within 10^–7–10^–4 S/cm at 100–120°C under anhydrous conditions. The thermal stability of the hyperbranched ionic liquids is determined by the nature of ionic-liquid groups and the amount of the introduced alkyl urethane fragments; it is in the range of 170–270°C.     

Requirements of amount of carbon nanotubes for damage detection in large polymer composite structures

Due to their very high electrical conductivity, the addition of carbon nanotubes (CNTs) into polymers such as epoxies makes these materials conductive. This conductivity has been utilized to provide damage sensing in composite structures. Usually, the amount of CNTs needs to be more than the percolation threshold to assure electrical conductivity. The percolation threshold is usually determined using small samples. For large samples, the amount of CNTs needs to be higher to take into account some non-uniformity of the dispersion. More CNTs would provide better conductivity. One normally expects that more CNTs would also provide better damage detection. However, it was found that this is not the case. Certainly, the amount of CNTs needs to be more than a certain lower limit to assure conductivity throughout the large structures. Once this condition is met, adding more CNTs would reduce the sensitivity for damage detection. The sensitivity of damage detection can be measured by the change in electrical resistance (due to the occurrence of damage) between grid points that are attached on the surface of the composite structure. Higher sensitivity in damage detection would enable coarse grids (larger distance between grid points). Coarse grid points would mean lower number of grid points, less space, less wiring and less weight. This paper describes this phenomenon in detail. It provides models that simulate the conductivity configurations. It also introduces a new term call “Aggregately Conductive Materials” to distinguish the particular conductive characteristics of materials that are made conductive by the addition of nano-particles.     

Magnetic,Electrical and Thermal Studies of Polypyrrole-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocomposites

This research paper comprises of the synthesis of polypyrrole (PPy)-Fe₂O₃ nanocomposites by employing the in situ chemical oxidative polymerization method. The concentration of the filler material was adjusted between 10–50 wt % of PPy. The synthesized nanocomposites were characterized by using X-ray diffraction (XRD). Magnetic analysis and DC electrical conductivity of the samples were carried out using vibrating sample magnetometer (VSM) and two probe DC conductivity method, point towards magnetically active and electrically conductive samples. The magnetic parameters under applied magnetic field demonstrated that the values of coercivity (H _c ), saturation magnetization (M _s ) and remanence (M _r ) can be tailored by carefully controlling the amount of dopant material into the nanocomposites indicating their suitability for controllable switching devices and microwave absorption applications. The DC electrical conductivity showed an increase up to 20 wt % of filler material and thereafter a decrease in the conductivity of nanocomposites with increase in filler content is observed. Thermogravimetric analysis (TGA) showed an increase in thermal stability with an increase in ferrite content in nanocomposites.