Study on the Gas Permeability of Nickel(II) Polyurethane Complexes

Ionic polyurethanes (PUs) were prepared from hydroxyl‐terminated polybutadiene (HTPB) and 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI) by a two‐stage method. The ionic group was introduced by adding 4,8‐diazaundecanediamide (L‐2,3,2) as the chain extender of which the tertiary amines and carbonyl groups were complexed with nickel ions. It was found that the binding of hard segments and the flexibility of soft segments had subtle effects on the gas permeability. The effects of hard segment content and the amount of nickel ion on the gas permeability and morphological properties were investigated. Fourier transform infrared (FTIR) spectroscopy was utilized to identify the segregation between hard and soft segments and structure change, which affect the transport properties. The hydrogen bonding index (HBI), frequency difference, and shift as a measure of the phase segregation and the average strength of the interpolymer hydrogen bonds were utilized to study the intermolecular interaction and transport property of the prepared PUs. The oxygen and nitrogen permeabilities of membranes were determined by using gas permeability analyzer. The results of FTIR, differential scanning calorimetry and thermogravimetric analysis measurements explain the complexation and, hence, the gas permeability.     

丁苯、丁腈基聚氨酯的形态与性能

用示差扫描量热法 (DSC)、红外分光光度计 (FTIR)和原子力显微镜 (AFM)研究了端羟基聚丁二烯 苯乙烯共聚物 (HTBS)、端羟基聚丁二烯 丙烯腈共聚物 (HTBN)和端羟基聚丁二烯 (HTPB)与甲苯二异氰酸酯、1 ,4 丁二醇构成的溶液法聚二烯烃基聚氨酯 (PU)的形态结构 .结果表明HTPB和HTBS基PU的相分离程度很大 ,而HTBN基PU的相分离程度小 .这可能归因于HTBS软段的极性低 ,不能与硬段形成氢键 ,而HTBN软段中的腈基具有很强的极性 ,且可以与硬段形成氢键作用 ,增加了软硬段间的相容性 ,相分离程度明显降低 .AFM表明HTBN PU随着硬段含量提高 ,表面粗糙度增大 ,由软段为连续相逐渐过渡到双连续结构 .在硬段含量 6 3%时 ,HTBN和HTPB基PU均呈双连续结构 ,而HTBS PU中硬段为连续相 .HTBN PU软段的相区尺寸在1 2nm左右 ,表面粗糙度较大 ,HPBS PU软段的相区尺寸在 1 1nm左右 ,表面粗糙度最小 ,HTPB PU存在 1 4nm和 5 0nm大小不等的软段相区尺寸 .力学性能表明 ,在软段中引入苯乙烯和丙烯腈结构 ,可使聚氨酯抗张强度分别提高 1 5和 2倍 ,模量和断裂伸长率也明显提高     

Gas permeability of cupric ion containing HTPB based polyurethane membranes

For the purpose of oxygen enrichment from air, the gas permeability and selectivity of an ionic polyurethane membrane was under investigation. Membranes of ionic polyurethane were prepared by step-growth polymerization of hydroxyl terminated polybutadiene (HTPB) and 4,4′-dicyclohexylmethane diisocyanate (H₁₂MDI). The ionic group was introduced by adding N-methyldiethanolamine (MDEA) as the chain extender of which the tertiary amines were complexed with cupric ions. The effect of hard segment content, polymerization method, peroxide introduction, and the amount of cupric ion on gas permeability were investigated. It was found that the binding of hard segment and the flexibility of soft segments had subtle effects on gas permeability. Membranes of the same composition were synthesized through two different procedures, one- and two-stage polymerization. The former contains large hard segment of cluster aggregation and flexible soft segments had a higher gas permeation rate. When a crosslinker, benzoyl peroxide, was added, the crosslinkage within soft segments hindered cluster formation by hard segment aggregation, the permeability increased. Furthermore, CuCl₂ addition enhanced hard segment aggregation, more hard segments formed cluster aggregates and less dispersed in soft segment region, which also increased permeability. However, excess CuCl₂ addition resulted in CuCl₂ piling up in the soft segment region, which restricted the movement of soft segments and therefore reduced the gas permeability.     

Sorption and diffusion of ethanol vapor in polybutadiene/acrylonitrile, polybutadiene/styrene and polybutadiene based polyurethanes

The sorption and diffusion behavior of ethanol vapor in series of polyolefine based polyurethanes (PU) made from hydroxyl-terminated polybutadiene/acrylonitrile (HTBN), hydroxyl-terminated polybutadiene/styrene (HTBS) and hydroxyl-terminated polybutadiene (HTPB) were investigated by using the quartz-spring, DSC, FTIR and AFM. The equilibrium absorption reduced with increasing content of hard segments for all the three types of PUs. The values of the maximum absorption were in the order of HTBN > HTBS > HTPB based PU and related to their composition. The non-Fickian diffusion was confirmed and the sorption was discovered mainly in the hard segments. The HTBN based PU revealed different sorption and diffusion behavior from the other two, which was resulted from its hydrogen bonding not only between ethanol and hard segments but also soft segments. The morphologies of PUs before and after ethanol absorption were also compared. The HTBN based PU showed the most evident phase re-congregation after ethanol absorption.     

Epoxidized HTPB‐based Polyurethane Membranes for Pervaporation Separation

Polyurethane (PU) solutions were synthesized with hydroxyl‐terminated polybutadiene (HTPB), 4,4′‐dicyclohexylmethane diisocyanate (H₁₂MDI) and 1,4‐butanediol (1,4‐BD). PU membranes were prepared by dry/wet method from PU solutions, while epoxidized membranes were prepared by dipping the dried PU membranes into a mixture of formic acid and hydrogen peroxide for the reaction with C=C double bonds of HTPB soft segments. The extent of epoxidized reaction, which forms epoxide or ether groups, on the PU membranes was quantified by the absorbance ratio of the epoxide group to the butadiene group (A_epoxide/A_C=C ratio). Effect of epoxidized time on the polymer composition, morphology, and polarity of these HTPB‐based PUs was investigated by FTIR‐ATR, DMA and contact angle meter. Both permeabilities and permselectivity of a water/ethanol mixture, which is measured by pervaporation method, were improved through the epoxidation of PU membranes.     

正电子湮没谱研究聚烯烃聚氨酯的自由体积、微观结构和溶剂的扩散行为

用正电子湮没技术(PAS)结合示差扫描量热法(DSC)研究了聚烯烃聚氨酯的自由体积特征和微相分离结构的关系.结果表明,硬段含量增加,自由体积孔洞平均半径和自由体积分数减小;丁腈聚氨酯相分离程度小,相应自由体积孔洞平均半径和自由体积分数小,而丁羟聚氨酯的情况正好相反.石英弹簧法对苯和乙醇蒸气的溶解和扩散行为的研究表明,聚烯烃聚氨酯的自由体积孔洞平均半径和自由体积分数与苯和乙醇溶剂蒸气的无限稀释扩散系数呈正相关,但它们的无限稀释扩散系数和自由体积分数关系无法用Fujita的自由体积模型描述,可能归因于它们对聚烯烃聚氨酯复杂的溶胀行为.     

HTPB‐based polyurethanes. II. SINs with PMMA

Simultaneous interpenetrating networks from poly(methyl methacrylate‐co‐ethyleneglycol dimethacrylate) (PA) and a hydroxyl‐terminated polybutadiene‐based polyurethane (PU) were prepared with various hard‐segment contents (X) in the PU and different ratios (PU/PA) between the components. The level of the reinforcement, the mechanism of molecular failure, and the phase inversion depended strongly on X. Dynamic mechanical results indicated that the interpenetration occurred in the rigid blocks of the PU. The improved thermal and mechanical properties observed with higher values of X were interpreted in terms of the molecular weight and polydispersity of the hard blocks in the PU. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2861–2872, 2000     

Synthesis of poly(vinyl ether)‐based,ABA triblock‐type thermoplastic elastomers with functionalized soft segments and their gas permeability

The ABA‐type triblock copolymers consisting of poly(2‐adamantyl vinyl ether) [poly(2‐AdVE)] as outer hard segments and poly(6‐acetoxyhexyl vinyl ether) [poly(AcHVE)], poly(6‐hydroxyhexyl vinyl ether) [poly(HHVE)], or poly(2‐(2‐methoxyethoxy)ethyl vinyl ether) [poly(MOEOVE)] as inner soft segments were synthesized by sequential living cationic polymerization. Despite the presence of polar functional groups such as ester, hydroxyl, and oxyethylene units in their soft segments, the block copolymers formed elastomeric films. The thermal and mechanical properties and morphology of the block copolymers showed that the two polymer segments of these triblock copolymers were segregated into microphase‐separated structure. Effect of the functional groups in the soft segments on gas permeability was investigated as one of the characteristics of the new functional thermoplastic elastomers composed solely of poly(vinyl ether) backbones. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1114–1124     

丁羟胶型聚氨酯弹性体的水解稳定性

丁羟胶型聚氨酯弹性体的水解稳定性;弹性体;扩链剂     

聚酯聚氨酯透气性的正电子研究

用正电子湮没寿命谱(PALS)研究了温度和PEG含量对以聚己二酸丁二醇酯(PBA)为软段的聚酯聚氨酯的自由体积特性和透气性的影响.实验结果表明,自由体积空洞的体积随着温度的升高而增加,分布变宽,导致透气性增大.不同PEG含量的聚酯聚氨酯PBA-10,PBA-15和PBA-20的水汽渗透系数(WVP)基本相同.结果表明,在这类聚氨酯中,影响透气性的主要因素不仅是自由体积,而且与材料的亲水性有关.     

The gas transport properties of amine-containing polyurethane and poly(urethane-urea) membranes

A series of amine-containing polyurethanes and poly(urethane-urea)s based on 4,4′-diphenylmethane diisocyanate and either poly(ethylene glycol) of molecular weights 400 or 600 were prepared as gas separation membranes. The amine functional groups of N-methyldiethanolamine (MDEA) and/or tetraethylenepentamine (TEPA) were introduced into the hard segment as a chain extender. The gas transport data of He, H₂, O₂, N₂, CH₄ and CO₂ in these polymer membranes were determined by using the Barrer's high-vacuum technique and the time-lag method. The restriction of chain mobility has been shown by the formation of hydrogen bonding in the soft segment and hard-segment domains, resulting in the increase in the density, glass transition temperature of soft segments (T_gs). The separation mechanism of various gas pairs used in industrial processes is also discussed. Effect of pressure on permeability of the gases above and below T_gs was studied. It was found that the gas permeability increased or decreased with upstream pressure above T_gs, and should be described by a modified free-volume model. On the other hand, the condensable CO₂ exhibits a minimum permeability at a certain upstream pressure below T_gs. The permeability of He and H₂ were pressure independent above and below the T_gs.     

Positron studies of the temperature-dependence of free volumes in Polydimethylsiloxane/poly(propylene oxide) urethane/urea membranes

Free-volume parameters in polyurethane/urea membranes have been studied by positron annihilation lifetime and Doppler broadening measurements. The bi-soft segment membranes were obtained by varying the ratio of the structural constituents, polypropylene oxide and polydimethylsiloxane (PU/PDMS), with PDMS content from 25 to 75 wt%. The free-volume holes determined by PALS are correlated with gas permeation features. The phase separation of the various soft and hard segments in the membranes is mirrored in both lifetime and Doppler results.     

Free-volume study of ethylene - vinyl alcohol copolymer evaluated through positronium lifetime measurement

The free-volume, of size ranging from 0.2 to 0.4 nm in radius, in an ethylene-vinyl alcohol copolymer was estimated using positronium lifetime measurement to elucidate the dependence of oxygen permeability on the free-volume size and fraction, on the ethylene content and on the crystallinity. The permeability and the free-volume fraction with varying the ethylene content were well related and the relation was interpreted based on the free-volume theory near below and above the glass transition temperature. On the other hand, the crystallinity significantly influenced the fraction of the amorphous region, where the free-volume hole exists, along with a slight change of the free-volume size. The variation of the permeability with the crystalline degree cannot be explained from the averaged free-volume fraction estimated by the whole volume of the polymer, but the permeability correlated with the free-volume size apparently.     

Effect of top layer swelling on the oxygen/nitrogen separation by surface modified polyurethane membranes

Cobalt(II) was chelated on the surface of a hydroxyl terminated polybutadiene (HTPB) based polyurethane (PU) membrane. The surface of a HTPB based PU membrane was first modified by ethylenediamine (EA) plasma. The cobalt chelated membrane was prepared by immersing the plasma treated membrane into a cobalt(II)/formamide solution for various length of time. For a fair comparison, the untreated and plasma treated membranes were also immersed in formamide solution. The gas transport properties of all three membranes were compared. Without solvent immersion, the O₂/N₂ selectivity increased from 2.6 to 3.1 after EA plasma treatment. But the permeability decreased from 0.88 GPU to 0.35 GPU. The selectivity was further improved to 4.4 by immersing the plasma treated membrane in a solution of CoCl₂·6H₂O/formamide for 1 h, but the permeability decreased to 0.23 GPU. The solvent immersion had little effect on the transport properties of the untreated membrane. But the transport properties of the plasma treated and cobalt chelated membranes were greatly affected by the formamide immersion. The oxygen and nitrogen permeabilities of the modified top layers could be calculated from a series model for composite membranes. It was found that both the permeability and selectivity of the top layer of the plasma treated membrane increased with the solvent immersing time. For the top layer of the cobalt chelated membrane, the gas permeability first decreased after 1 h immersion and then increased after further immersion in CoCl₂·6H₂O/formamide solution. The selectivity of cobalt chelated membrane increased as the gas permeability decreased and vice versa. These results implied that the EA grafting enhanced the O₂/N₂ selectivity by increasing its oxygen affinity but the cobalt chelating increased the O₂/N₂ selectivity by enhancing the size sieving effect.     

High performance UV cured polyurethane dispersion

Imide groups were introduced in the hard segment of UV cured polyurethane dispersion (UV-PUD) by extending the NCO terminated prepolymers with pyromellitic dianhydride (PMDA) where the soft segments were prepared from PTMG, H₁₂MDI, HDI and DMBA. It was found that imide hard segment, as compared with conventional urethane hard segment gave remarkably high mechanical properties as well as thermal stability in terms of decomposition temperature and dynamic mechanical properties at elevated temperatures, and the results were interpreted based on the partial mixing of soft segments and imide hard segments.     

不饱和聚酯／聚氨酯复合体系的研究

以端羟基不饱和聚酯（ＨＵＰ）与聚氨酯（ＰＵ）浇注型复合网络聚合物（ＣＰＮｓ）为基材，考察了化学动力学及相分离对ＣＰＮ聚合物物理机械性能的影响．数据揭示了不饱和聚酯／聚附聚氨酯（ＨＵＰ／ＰＵ－ｅｓ）ＣＰＮ，当ｒ＝ＮＣＯ／ＯＨ＝０．４时，它的物理力学性能优于不饱和聚酯／聚醚聚氨酯（ＨＵＰ／ＰＵ－ｅｔ）ＣＰＮ或ＨＵＰ／ＰＡＰＩＣＰＮ组成物．最佳ＣＰＮ可通过调整聚氨酯中软段和硬段组分及网络组成而设计与制备．     

BARRIER PROPERTY AND STRUCTURE OF ACRYLONITRILE/ACRYLIC COPOLYMERS

A series of acrylonitrile (AN) copolymers with methyl acrylate (MA) or ethyl acrylate(EA) as comonomer (5--23 wt%) was prepared by free-radical copolymerization. The per-meability coefficients of the copolymers to oxygen and carbon dioxide were measured at1.0 MPa and at 30℃, and those to water vapor also measured at 100% relative humidityand at 30℃. All the AN/acrylic copolymers are semicrystalline. As the acrylate contentincrease, the permeability coefficients of the copolymers to oxygen and carbon dioxide areincreased progressively but those to water vapor are decreased progressively The gas per-meability coefficients of the polymers were correlated with free-volume fractions or the ratioof free volume to cohesive energy.     

Gas Permeation Properties of Organic-Inorganic Hybrid Membranes Prepared from Hydroxyl-Terminated Polyether and 3-isocyanatopropyltriethoxysilane

Organic-inorganic hybrid materials were prepared by reacting 3-isocyanatopropyltriethoxysilane (IPTS) with hydroxyl terminated poly(ethylene glycol) (PEG), poly(propylene glycol) (PPG) and poly(propylene glycol)-block-poly(ethylene glycol)-block-poly(propylene glycol) (PEPG), followed by hydrolysis and condensation with acid catalysis. Composite membranes have been obtained by casting hybrid sol on the microporous polysulfone substrate. The membranes were characterized by Fourier transform infrared (FT-IR), ¹³C NMR and ²⁹Si NMR. The permeability coefficients of N₂, O₂, CH₄ and CO₂ were measured by variable volume method. The gas permeability coefficients increase with increasing molecular weight of the polyethers. For the membranes containing PEG and PEPG, the higher values of CO₂ permeability coefficients and CO₂/N₂ separation factors are due to the presence of ethylene oxide segments. In case of PEPG membranes, molecular weight has more influence on CO₂ permeability than the effect of facilitation by ethylene oxide. The addition of TEOS into hybrid sol results in the decrease of all the gas permeability and does not affect the gas selectivity. PEG2000 membrane display the most performance among the hybrid membranes investigated here. The best values observed are CO₂ permeability of 94.2 Barrer with selectivity of 38.3 for CO₂/N₂ and 15.6 for CO₂/CH₄.     

聚硅氧烷聚脲多嵌段共聚物中氢键的研究

采用多种手段研究了聚硅氧烷与聚脲嵌段共聚物中所存在的各类氢键．特别探讨在聚硅氧烷软段中引入极性氰丙基对体系成氢键能力的影响和两相间相互作用力的情况结果表明，在软段分子中引入极性氰丙基有利于增加聚硅氧烷分子与聚脲链段的相互作用，这一相间作用力使两相间界面层厚度随着硬段分子量的增加而加宽，并发现在聚硅氧烷聚脲嵌段共聚物中硬段的聚集形态随溶液浓度改变变化不大，其中氢键随着温度升高而下降．     

Hydrolytic stability of oligoesters: comparison of steric with anchimeric effects

A comparison of steric and anchimeric effects on the hydrolytic stability of polyesters was studied. Twelve monomers were selected based on their propensity toward steric and anchimeric interactions: adipic acid, isophthalic acid, phthalic anhydride, hexahydrophthalic anhydride, 1,4-cyclohexanedicarboxylic acid, maleic anhydride, ethylene glycol, 1,2-propanediol, 1,3-propanediol 1,4-butanediol, 1,5-pentanediol, and neopentyl glycol. Hydroxyl terminated oligoesters consisting of one diacid and one diol and one hydroxyl terminated oligoester consisting of two diacids and one diol were prepared. The hydrolytic stability was evaluated in an acetone/water solution. The acid number was monitored as a function of time. It was found that telechelic groups favor anchimeric interactions, while steric groups determine the rate of hydrolysis for the main chain.