Structural anisotropy in unstretched and uniaxially stretched poly(p‐phenylene vinylene)

Poly(p‐phenylene vinylene) or PPV is gaining increasing importance because of its superior electroluminescent efficiency and electrical conductivity. The most widely followed synthetic route for PPV involves synthesis of a precursor polymer using a sulfonium monomer salt. Previous studies have proven that the monomer salt which contains cyclic sulfonium groups yields better quality PPV than when the monomer containing dialkyl sulfonium groups is used. The structure of PPV synthesized using cyclic sulfonium precursor has not been as widely reported as that synthesized using dialkyl sulfonium monomer. In the current work, the structure of PPV, synthesized using a cyclic viz. tetrahydrothiophenium monomer salt, has been studied in detail using the wide angle X‐ray diffraction (WAXD) technique. The study reveals that even in the cast (unstretched) form, PPV shows considerable biaxial orientation in the plane of the film. This preferred orientation is found to occur during the casting process and is independent of the solvent used and casting substrate. On stretching these films to a final draw ratio of 7 : 1, this biaxial orientation is transformed into uniaxial orientation with nematic ordering of PPV chains along the stretch direction and PPV chains assuming three preferred orientations in the plane of the film. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 605–614, 1999     

Structure and electrical properties of undoped oriented poly(phenylene vinylene) films

The influence of anisotropic structure on the electrical properties of undoped oriented poly(phenylene vinylene) (PPV) films was investigated with impedance spectroscopy and structural characterization. The oriented structure of the stretched PPV films was studied with wave-guide coupling and infrared dichroism. It was found that the unstretched PPV film had a highly planar structure, and one-way stretching converted the planar structure into a uniaxial structure. The impedance of undoped PPV thin films was measured along three different directions: through the film thickness direction, parallel to the stretch direction in the film plane, and perpendicular to the stretch direction in the film plane. Two relaxations were observed, one corresponding to the bulk behavior in the high-frequency range and the other to an interfacial contact polarization in the low-frequency range. From equivalent circuit modeling, it was found that the bulk conductivity through the film thickness direction decreased with increasing orientation, whereas the high-frequency dielectric constant through the film direction remained constant. In addition, the conductivities measured in the film plane were at least two orders of magnitude higher than the conductivity in the direction normal to the film surface. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 98–116, 2004     

Syntheses and electroluminescence properties of conjugated poly(p‐phenylene vinylene) derivatives bearing dendritic pendants

A series of new poly(p‐phenylene vinylene) derivatives with different dendritic pendants—poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE–PPV), poly{2‐[3′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBE–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBD–PPV), and poly[(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)‐co‐(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)] (BBE‐co‐BBD–PPV; 1:1)—were successfully synthesized according to the Gilch route. The structures and properties of the monomers and the resulting conjugated polymers were characterized with ¹H and ¹³C NMR, elemental analysis, gel permeation chromatography, thermogravimetric analysis, ultraviolet–visible absorption spectroscopy, photoluminescence, and electroluminescence spectroscopy. The obtained polymers possessed excellent solubility in common solvents and good thermal stability, with a 5% weight loss temperature of more than 328 °C. The weight‐average molecular weights and polydispersity indices of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were in the range of 1.33–2.28 × 10⁵ and 1.35–1.53, respectively. Double‐layer light‐emitting diodes (LEDs) with the configuration of indium tin oxide/polymer/tris(8‐hydroxyquinoline) aluminum/Mg:Ag/Ag devices were fabricated, and they emitted green‐yellow light. The turn‐on voltages of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were approximately 5.6, 5.9, 5.5, 5.2, and 4.8 V, respectively. The LED devices of BE–PPV and BD–PPV possessed the highest electroluminescent performance; they exhibited maximum luminance with about 860 cd/m² at 12.8 V and 651 cd/m² at 13 V, respectively. The maximum luminescence efficiency of BE–PPV and BD–PPV was in the range of 0.37–0.40 cd/A. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3126–3140, 2005     

Synthesis and optical properties of a poly(2′,5′-dioctyloxy-4,4′,4″- terphenylenevinylene) with high content of (Z) vinylene units

Poly(2′,5′-dioctyloxy-4,4′,4″-terphenylenevinylene) with (E) configuration of the vinylene double bonds was prepared by Suzuki-Miyaura polymerization of (E)-4,4′-dibromostilbene and 2,5-dioctyloxy-1,4-benzenediboronic acid. Attempts to extend this simple procedure to the synthesis of the polymer with (Z) configuration, starting from (Z)-4,4′-dibromostilbene, were unsuccessful. However, the use of (Z)-4,4′-diiodostilbene and a careful choice of Pd catalyst and experimental conditions, lead to a material with a >95/<5 (Z)/(E) ratio of vinylene units. The investigation of optical properties of both the (E) and (Z) polymers evidenced that (Z) linkages act as defects which reduce the effective conjugation length in the polymer backbone.     

Properties of single‐walled carbon nanotube‐based poly(phenylene vinylene) electroluminescent nanocomposites

Devices with varying concentrations of single‐walled carbon nanotubes (SWNTs) dispersed in three derivatives of poly(p‐phenylene vinylene) are prepared, and their electroluminescent properties evaluated. Increasing the concentration of SWNTs improves the electrical conductivity of the nanocomposites. However, an undesired increase in the electroluminescence (EL) turn‐on voltage is observed for the hybrids, possibly due to photoluminescence quenching of excitons by the SWNTs. At relatively low concentrations of SWNTs, there is an increase in the EL lifetime; in contrast, at relatively high concentrations of SWNTs, due to photoluminescence quenching by the nanotubes, significant reduction in brightness and faster degradation of the EL performance of the devices is observed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Nanotubes of poly(phenylene vinylene) derivative at the air/water interface

Different sizes of nanotubes of poly(2-methoxy-5-(n-hexadecyloxy)-p-phenylene vinylene)(MH-PPV) have been fabricated at the air/water interface by compressing a monolayer of MH-PPV beyond its collapse point, and their structural characteristics were studied by means of TEM, AFM, SAXRD, IRRAS.     

Syntheses of new poly (arylene vinylene) analogues: Poly (4,7-benzofuran vinylene) and poly (4,7-benzothiophene vinylene)

The reaction of bis(4,7-tetrahydrothiopheniomethyl) benzofuran dibromide with aqueous tetramethylammonium hydroxide leads to a water-soluble polyelectrolyte which can be film cast and thermolytically eliminated to give poly(4,7-benzofuran vinylene) (PBFV). Subjection of bis(4,7-tetrahydrothiopheniomethyl) benzothiophene dibromide to the same reaction sequence gives poly(4,7-benzothiophene vinylene) (PBTV). UV-VIS studies show that PBFV has a band gap of 2.76 eV, while PBTV has a band gap of 2.92 eV. These polymers are members of a new class of conjugated poly (arylene vinylene)s, in which heterocyclic pseudoaromatic rings are fused onto a poly(1,4-phenylene vinylene) backbone. © 1994 John Wiley & Sons, Inc.     

Comparative study of the optical,electrochemical, electrolumiscent,and photovoltaic properties of dendritic pendants modified poly(p‐phenylene vinylene)s

In this study, the optical, electrochemical, electrolumiscent, and photovoltaic properties of a series of poly(p‐phenylene vinylene) (PPV) derivatives bearing different dendritic pendants, poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE‐PPV), poly{2‐[2′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD‐PPV), poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (MEH‐PPV), poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene}‐co‐poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1,4‐phenylenevinylene] (BE‐co‐MEH‐PPV), and poly{2‐[2′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene}‐co‐poly[2‐methoxy‐5‐(3′,7′‐dimethyloctyloxy)‐1,4‐phenylenevinylene] (BD‐co‐MDMO‐PPV), were investigated. The steric pendants strongly affect the absorption spectra, photoluminescence (PL) sepctra, the onset oxidation/reduction potentials, and further affect the electrolumiscent and photovoltaic properties. Copolymerization can reduce the steric effect and improve the electrolumiscent and photovoltaic properties. The brightness of light‐emitting diodes base on copolymer BE‐co‐MEH‐PPV and BD‐co‐MDMO‐PPV reached 3988 and 3864 cd/m², respectively, much higher than that based on homopolymer BE‐PPV (523 cd/m²) and BD‐PPV (333 cd/m²), also higher than that based on MEH‐PPV (3788 cd/m²). The power conversion efficiency (PCE) of solar cells based on BE‐co‐MEH‐PPV and BD‐co‐MDMO‐PPV reached 1.41, 0.76%, respectively, much higher than that based on BE‐PPV (0.24%) and BD‐PPV (0.14%). Copyright © 2010 John Wiley & Sons, Ltd.     

Density functional crystal orbital study of cyano‐substituted poly(para‐phenylene‐vinylene) and poly(quinoxaline‐vinylene)

We have calculated the optical and electronic properties of several conjugated organic polymers: poly(p‐phenylene‐vinylene) (PPV) and its derivatives. Cyano substitutions on the phenylene ring: poly(2,5‐dicyano‐p‐phenylene‐vinylene) (2,5‐DCN‐PPV) and on the vinylene linkage: poly(p‐phenylene‐7(,8)‐(di)cyano‐vinylene) are considered. In addition, poly(quinoxaline‐vinylene) (PQV) is studied. The infinite isolated quasi‐1D chains are treated with periodic boundary conditions, using atomic basis sets. In a comparative study of PPV, some issues regarding the selection of the functionals and basis sets are discussed and excitation energies derived from time‐dependent and from ordinary methods are compared. It is concluded that for these polymers the calculations are informative at the B3LYP/6‐31G** density functional theory (DFT) level. The absolute values might change with improved methods, but the similarity of the polymers suggests that the relative characterization is adequate. Band structures are communicated along with characteristics of the highest occupied and the lowest unoccupied crystal orbitals (HOCO and LUCO). Electron affinities, ionization potentials, valence and conduction bandwidths, and effective masses at the bandgap are given. © 2006 Wiley Periodicals, Inc. Int J Quantum Chem, 2006     

Pyrolysis of poly(phenylene vinylene)s with polycaprolactone side chains

The thermal degradation characteristics of a new macromonomer poly(-caprolactone) with central 4,4′-dicarbaldehyde terphenyl moieties and poly(phenylene vinylene)s with well defined (-caprolactone), (PPV/PCL) as lateral substituents were investigated via direct pyrolysis mass spectrometry. The unexpectedly high thermal stability of the macromonomer was attributed to intermolecular acetylation of benzaldehyde yielding a hemiacetal and causing a crosslinked structure during the pyrolysis. Increased thermal stability of the PCL chains was detected for all samples. The increase in stability of PCL chains was much more pronounced than was detected for poly(p-phenylene)-graft-poly(-caprolactone) copolymer (PPP/PCL); the upward temperature shift was about 100 °C for PPV/PCL and only 20 °C for PPP/CL. This pronounced effect may be due to higher thermal stability of PPV compared to PPP and the decrease in steric hindrance for PPV with PCL side chains.     

Oligo(phenylene vinylene)-poly(methylstyrene) hybrids: controlled step-wise molecular wiring of oligo(phenylene vinylene)

Well defined oligo(phenylene vinylene) grafted polymers known as oligo(phenylene vinylene)-poly(methylstyrene) hybrids have been developed using a step-wise synthetic protocol, where the length of the OPV can be controlled systematically to achieve specific optoelectronic properties. The process allows the structural modification of attached OPV at a molecular level either by varying the chain length or by changing functionalities. The step-wise generation of OPV chains on the backbone of a highly soluble polymer ensures solubilization in a variety of solvents and also the exhibition of interesting optical properties.     

Electroluminescent properties of a partially‐conjugated hyperbranched poly(p‐phenylene vinylene)

In this paper, the electroluminescent properties of a new partially‐conjugated hyperbranched poly (p‐phenylene vinylene) (HPPV) were studied. The single layer light‐emitting device with HPPV as the emitting layer emits blue‐green light at 496 nm, with a luminance of 160 cd/m² at 9 V, a turn‐on voltage of 4.3 V and an electroluminescent efficiency of 0.028 cd/A. By doping an electron‐transport material [2‐(4‐biphenylyl)‐5‐phenyl‐1,3,4‐oxadiazole, PBD] into the emitting layer and inserting a thin layer of tris(8‐hydroxy‐quinoline)aluminum (Alq₃) as electron transporting/hole blocking layer for the devices, the electroluminescent efficiency of 1.42 cd/A and luminance of 1700 cd/m² were achieved. The results demonstrate that the devices with the hyperbranched polymers as emitting material can achieve high efficiency through optimization of device structures. Copyright © 2006 John Wiley & Sons, Ltd.     

Preparation of poly(phenylene vinylene) from cycloalkylene sulfonium salt monomers and polymers

Two new types of p-xylene bis-sulfonium chloride monomers were prepared from cycloalkylene sulfides. The polymerization characteristics of these monomers to form poly(p-xylene sulfonium chlorides), and the thermal elimination reactions of their polymers to poly(p-phenylene vinylene), were compared with those of two monomers prepared from dialkyl sulfides. The cycloalkylene sulfonium chloride monomer polymerized to higher yields and to higher molecular weight polymers, which showed more efficient elimination reactions.     

Photoluminescent properties of poly(p‐phenylene vinylene thiophene‐co‐siloxane)

A new p‐phenylene–vinylene–thiophene‐based siloxane block copolymer has been synthesized. The copolymer consists of alternating rigid and flexible blocks. The rigid blocks are composed of phenylene–vinylene–thiophene‐based units, and the flexible blocks are derived from 1,3‐dialkyldisiloxane units. The former component acts as the chromophore, and allows fine tuning of band gap for blue‐light emission, while the latter imparts good solubility of the copolymer in organic solvents, and thus, should enhance processibility of the resulting copolymer. The thermal properties of the copolymer have been characterized by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The photoluminescence (PL) of the copolymer in solution and in cast film has been studied. The effects of concentration on the PL intensity of the new copolymer in polymer blends with poly(methyl methacrylate) (PMMA) and poly(vinyl carbazole) (PVK) have also been described. Efficient energy transfer from PVK to the new block copolymer in the blended film was observed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1450–1456, 2000     

Synthesis of some new pyrazolyl-thiazolidinone derivatives starting from 1-(3-chlorophenyl)-3-(4-methoxyphenyl)-1H-pyrazole-4-carboxaldehyde

Russian Journal of General Chemistry - A novel synthetic approach to (E)-1-{[1-(3-chlorophenyl)-3-[(4-methoxyphenyl-1H-pyrazol-4-yl)- methylene]hydrazono}-3-phenylthiazolidin-4-one starting from...     

Synthesis and structures of new metallocene derivatives of lanthanides. Molecular structures of the complexes (C13H9)2Eu(THF)2 and (C5Me4H)2YbI(THF)

The divalent europium bis-fluorenyl complex (C₁₃H₉)₂Eu(THF)₂ was synthesized by the metathesis reaction of EuI₂(THF)₂ with two equivalents of fluorenylpotassium and by the protolytic substitution of the naphthalene ligand in the (C₁₀H₈)Eu(THF)₂ complex using the reaction with fluorene. According to X-ray diffraction data, the complex displays a skewed sandwich structure, in which one fluorenyl ligand is η⁵-coordinated to the metal atom, whereas the η³-coordination mode makes a great contribution to the coordination of another ligand. The (C₅Me₄H)₂YbI(THF) complex was synthesized by the reaction of YbI₃(THF)₂ with two equivalents of (C₅Me₄H)K. The structure of the complex was established by X-ray diffraction. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 530–534, March, 2008.     

Synthesis and characterisation of poly(arylene sulphides)—Part 1: Poly(phenylene sulphide), poly(2-methyl phenylene sulphide) and poly(2,6-dimethyl phenylene sulphide)

A facile synthesis of poly(phenylene sulphide) (PPS), poly(2-methyl phenylene sulphide) (PMPS) and poly(2,6-dimethyl phenylene sulphide) (PDMPS) by solution polymerisation of the respective copper(I)-4-bromothiophenoxides at atmospheric pressure is described. Conditions have been optimised for the preparation of high molecular weight materials and these have been characterised prior to studies of their curing behaviour and thermal-oxidative degradation.     

Bipolar poly(p‐phenylene vinylene)s bearing electron‐donating triphenylamine or carbazole and electron‐accepting quinoxaline moieties

Two new poly(phenylene vinylene)s (PPVs) carrying electron‐donating triphenylamine or carbazole and electron‐deficient quinoxaline units were synthesized and characterized. Their properties were compared with those of PPV containing only quinoxaline unit. The two polymers showed PL maximum at 501–510 in solution and 533–540 in thin film. Because of the presence of electron donor and acceptor units they displayed strong intramolecular charge transfer (ICT) effects; hence, low‐photoluminescence quantum yields. The polymers showed reversible electrochemical reduction with electron affinity of 2.75 eV and irreversible oxidation with ionization potential of 5.10–5.24 eV. Single‐layer LED of configuration ITO/PEDOT/polymer/Al showed low turn‐on voltage at 5 V, but limited brightness of 50–60 cdm^?2. The electroluminescence maximum was voltage‐tunable varying from 500 to 542 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2367–2378, 2008     

Synthesis, structural characterization and reactivity of the amino borane 1-(NPh2)-2-[B(C6F5)2]C6H4

The bright red title compound 1 was synthesized from (2-lithiophenyl)diphenylamine and bis(pentafluorophenyl)boron chloride. Its reactions with small acids like H₂O and HCl proceeded easily giving zwitterionic compounds. For 1 and its water adduct 2 the crystal structures were determined, the latter featuring an ammonium borate structure containing a short intramolecular hydrogen bond bridge. Treatment of 1 with Jutzi's acid, [H(OEt₂)₂][B(C₆F₅)₄], did not result in protonation of the nitrogen, but reaction of 1 with LiH in the presence of 12-crown-4, led to the isolation of the aminoborate [1-(Ph₂N)-2-{B(H)(C₆F₅)₂}C₆H₄][Li(12-crown-4)] (3). Borohydride 3 reacted with Jutzi's acid to regenerate 1 and liberate hydrogen.