Titrations using an apparatus for recording the antilogarithm of pH or pM

A titration apparatus plotting either the concentration of sample ion or the concentration of titrant ion has been tested. An antilog apparatus, converting measured e.m.f. values into concentrations is connected to ordinary titration equipment. The instrument has been tested by means of acid—base titrations (titrations of mixtures of weak acids and of a weak and a strong acid), precipitation titrations (determination of the chloride concentration in tap-water, titration of mixtures of halides), titrations with ion-selective electrodes (determination of the fluoride content of toothpaste) and complexometric titrations (determination of copper with EDTA, using mercuric ion as indicator ion and amalgamated silver rod as indicator electrode, or using a copper-selective indicator electrode). The method considerably simplifies the evaluation of the results as compared to conventional potentiometric titrations.     

Computer controlled titration with piston burette or peristaltic pump – a comparison

The advantages and problems of the use of piston burettes and peristaltic pumps for dosage of titrant solutions in automatic titrations are shown. For comparison, only the dosing devices were exchanged and all other components and conditions remained unchanged. The results of continuous acid base titration show good agreement and comparable reproducibility. Potentiometric sensors (glass electrodes) with different equilibration behaviour influence the results. The capability of such electrodes was tested. Conductometric measurements allow a much faster detection because there is no equilibration of electrodes. Piston burettes should be used for titration with very high precision, titration with organic solvents and slow titrations. Peristaltic pumps seem to be more suitable for continuous titrations and long time operation without service.     

Application of various electrodes in potentiometric titration of calcium

In complexometric titrations various indicator electrodes may be employed for monitoring the course of titration and for detection of the end-point. Several of them, including the silver, mercury, bivalent cation membrane, calcium membrane and manganese dioxide electrodes were investigated and compared in their usefulness. As titrant, EDTA was mostly used, but results with similar chelating titrants were also obtained. The practical utility of the electrodes in titrations depends on their selectivity, magnitude of the end-point break and precision in determination of the end-point. For the electrodes studied, in some instances there is good correlation between the theoretical and experimental titration curves, but it is not always possible to predict the electrode response in the low activity range. In other cases poor correlation does not mean that reasonably good analytical results may not be obtained.     

Acid-base titrations by stepwise addition of equal volumes of titrant with special reference to automatic titrations-IV Photometric titration of an acid

In Part I of this series, evaluation methods for potentiometric titrations of acids performed by stepwise addition of titrant were introduced. These methods are non-approximative and may therefore in principle be applied to titrations of acids of any strength. This paper demonstrates that photometric titrations performed by stepwise addition of titrant may also be evaluated by the proposed methods. The photometric method is compared with the potentiometric method of monitoring the course of a titration.     

Two-phase titration of organic ammonium ions with lauryl sulphate and methyl yellow as indicator

Conditions for determination of quaternary ammonium compounds and amines by two-phase titration have been calculated on the basis of extraction constants for the ion-pairs between the titrant (lauryl sulphate), the indicator (Methyl Yellow) and the sample. Methods for determination of extraction constants are presented. The precision and selectivity of the method are demonstrated by titrations of ammonium ions with different structures and degrees of substitution. The results are in agreement with the theoretical calculations.     

Potentiometric titrations using dual microband electrodes.

We present a novel method of analysis using potentiometric end-point detection and dual microband electrodes in generator-collector mode. The titrant is electrogenerated using either a constant current or a current that increases linearly with time, and the fluxes of reactive material rather than molar amounts are balanced. The advantage of the ramp current system over the constant current method is that all of the information needed for a full titration curve and a proper analysis can be obtained during a single scan. The method was applied to the determination of vitamin C with ferricyanide and to the determination of thiosulfate and sulfite with iodine using gold microband electrodes. As a new type of analysis, a potentiometric titration that uses dissolving silver microband electrodes in order to generate the titrant is demonstrated. The system was applied to the detection of chloride, iodide, thiosulfate and cyanide. The accuracy of the analysis is +/-10%, limited mainly by the present screen-printing process, and the method is well adapted for measurements on the millimolar scale.     

Optimization of the automatic microtitration of chlorides,bromides and iodides

Summary The most favourable conditions for performing the potentiometric micro-scale determination of chlorides, bromides and iodides by their automatic titration with silver nitrate have been investigated. For this purpose, an automatic device has been considered which is able to perform the titrant addition, either for preselected time intervals, or by adjusting them automatically so that the change of potential with time reaches a preselected value.The results obtained indicate that rapid (about two minutes) and accurate titrations can be performed for chlorides with almost all of the parameters chosen, while results affected by a large positive error are obtained for bromides and iodides when the operation modes adopted imply too frequent titrant additions.The weighed samples contain 1.5 to 4 mg halide.     

高精度散射光度滴定法测定诺氟沙星的含量

用四苯硼钠标准溶液作滴定剂,采用高精度散射光度滴定法测定了诺氟沙星的含量,并将测定结果与非水滴定法、非水电位滴定法和高效液相色谱法的测定结果进行比较。结果表明：用本方法测定诺氟沙星的含量具有较高的准确度、精密度和良好的线性,且不受其降解产物的干扰。     

Titrimetric analysis with adding the titrant by means of electrodialysis

A titration method is developed that titrant is added continuously to the analyte by electromigration through an ion exchange membrane. A constant rate of the titrant addition is achieved by keeping the electric current constant. Analyte amount then is proportional to the titration time. The method is applied to the most widely used titrations with a visual end point indication.     

In Process Citation

A first attempt to apply inorganic membranes made from parchment paper impregnated with alkaline earth precipitates, as indicating electrodes for potentiometric acid-base titrations in nonaqueous media, is presented. Mixtures of acids can be titrated and the course of the titration is a function of the nature of the solvent and the titrant.     

Robust flow-batch coulometric/biamperometric titration system: determination of bromine index and bromine number of petrochemicals

A flow–batch system was constructed and evaluated to perform coulometric titrations with biamperometric end point detection. The flow section of the system is employed for sampling by injecting a sample volume (50–300 μL) in a flow injection-like system. About 1.5 mL of a suitable carrier solution is delivered by a peristaltic pump in order to quantitatively transfer the sample to the system titration cell (2.0 mL total inner volume). The carrier contains the coulometric precursor for the titrant species. The cell contains two pairs of platinum electrodes used for coulometric generation of reagent and biamperometric detection and is actively stirred. The titrant species is generated and the titration is performed by the usual batch procedure with the excess of titrant being detected by biamperometry following the analysis of the titration curve. System operation is computer controlled and all operations are automated, including titration curve analysis and cell cleaning after the titration is ended. The system is characterized by its robustness because its operation does not depend on flow rates, and the work using coulometric methods which generate gases at the counter-electrode is not troublesome. The flow–batch system has been evaluated for determination of bromine index and bromine number (relative to the total reactive olefin content) in petrochemicals according to an ASTM procedure. Typical precision (R.S.D.) is between 0.5 and 6% for different petrochemicals whose bromine number/index vary from 1000 to 10 mg of bromine per 100 g of sample, respectively. Recoveries for standard additions are between 92 and 123% for 10 mg of Br₂ per 100 g increments and 98 to 101% for 100 mg per 100 g increments. Accuracy of the proposed system was evaluated against results obtained by the standard ASTM with no significant difference detected at 95% confidence level.     

Titration curves in complexometric titrations with the redox system Fe(III)/Fe(II)

Potentiometric titrations of metal ions with EDTA have been carried out with a platinum or graphite electrode and the Fe(III)/Fe(II) redox system. In the absence of oxygen and for pH < 2 the titration curves may be described by an equation similar to that given previously for titrations with silver and mercury electrodes. Titration curves for bismuth and indium, which are more strongly complexed than iron, are asymmetrical and useful for analytical purposes. When the titrated ions are complexed less strongly than iron(III) ions the kinetics of metal complexation have a pronounced effect. The titration curves of thorium and copper, which react more rapidly than iron, are analytically useful. The curves recorded rapidly after titrant additions have a better end-point break than those which correspond to thermodynamic equilibrium. When a metal, e.g., nickel, is weakly bound by EDTA, and reacts more slowly than iron, a very small end-point break or none at all is observed.     

PVC膜修饰电极上零电流示波电位滴定法测定硼的研究

以氯化十六烷基吡啶（ＣＰＣ）和氟硼酸钠形成的离子缔合物为活性物质，制成ＰＶＣ膜涂层石墨电极，提出了一个快速测定硼的零电流示波电位滴定法。以ＣＰＣ为滴定剂，用ＰＶＣ膜电极为指示电极，甘汞电极为参比电极，利用阴极射线示波器荧光屏上荧光点的突然位移来指示ＣＰＣ滴定硼的终点，具有灵敏、准确、快速等特点，用该法测定玻璃中的硼，结果良好。     

Development of algorithms for automated spectrophotometric titrations

A versatile method for evaluation of equilibrium constants from automated spectrophotometric titrations is described. General algorithms were derived for normalized titration curves of reactions having various stoichiometric ratios. Normalization of data involve converting it from absorption versus time to product formed (0 to 1) versus equivalents of titrant added. Relevance of derived algorithms was assessed by the quality of their fit to real data. The demonstration system chosen for this investigation was the 1:3 complexation reaction of Fe(II) and 1,10-phenantroline (o-Phen). Titrations were performed at three distinct infusion rates under controlled pH of 5.0 and at 25.0 °C, with sets produced using both Fe(II) and o-Phen as the titrant. Direct fitting of titration curves yielded values for overall equilibrium constants. Furthermore, resulting curves revealed reproducible initial deviation, consistent with step-wise reaction, when titrating Fe(II) with o-Phen. No unusual deviations were evident anywhere in the titration curves when Fe(II) was the titrant. Overall, our approach facilitates adoption of automated titrimetry and data analysis methodologies for the determination of stoichiometries and equilibrium constants of many UV/Vis active reactions.     

Metal oxide electrodes as sensors in complexometric titrations

EDTA titrations of lead and manganese, and of some other ions by using these as indicator ions, have been followed potentiometrically with PbO(2) and MnO(2) electrodes. Explanations are put forward for the anomalies observed in the titration curves. With the MnO(2) electrode, formation of an Mn(III)-EDTA complex is responsible for the diminished potential breaks. With the PbO(2) electrode the decrease in the potential break and the distortion of the curves in acid solution may be due to reaction between electrode coating and titrant. The MnO(2) electrode has been used for titrations of Ba(2+) Ca(2+), Cd(2+) and Cu(2+) with errors < 1%.     

The computerized determination of double-layer capacitance with the use of kalousek-type waveforms and its application in titrimetry

A method for the rapid determination of double-layer capacitance—potential curves of electrodes is described. An on-line computer is used to apply Kalousek-type waveforms to the electrochemical cell and to measure the accompanying current response. The capacitances are determined from the slope of the plots of log current against time. For 0.1 M KCl, the computerized method agrees well with the bridge method, except for the potential range of 0 to –0.15 V. The method is very useful for automating titrations with tensammetric detection of the end-point. The method is applied to the titration of barium with a macrocydic compound (kryptofix 222) and the titration of cetyl-trimethyl-ammonium bromide with bromocresol purple. The accuracy of the titrations is ±2%.     

Coulometric titration with air transported sample

Air transported samples of a mixture containing the analyte and a supporting electrolyte are consecutively propelled into a microconduit system through a titration cell, a coil and a detector cell. Different amounts of electrochemically generated titrant are obtained in the separate samples while they are passing through the titration cell. Various quantities of the titrant are achieved by changing the duration of the titrant generating process that is done by various time for the sample solution staying in the titration cell (different sample movement rate). The titrated sample is then homogenised in the coil and detected in an electrochemical detector cell that supplies necessary data for the analyte determination. The declared method is experimentally verified on coulometric titration of hydrochloric acid (HCl) with electrogenerated sodium hydroxide and a titration of aniline with bromine generated in a bromide solution.     

pH-stat techniques in titrimetric analysis: Part 3. The principles of pH-stat chelatometric titrations

Chelatometric titrations can be effectively monitored by means of the pH-stat technique. During the addition of the primary titrant (the chelating agent), the pH of the titrated solution is kept at a pre-selected value by adding a strong base as the auxiliary titrant. The equivalence point is characterised by a sudden change in the ratio between the added volumes of auxiliary and primary titrant solutions, i.e. in the slope of the linearly segmented titration plot representing the volume of the base against the volume of the chelating agent. The slope of the linear segments depends on the reactions involving proton exchange, which accompany the primary complexation reaction. The dependence of the shape of the plots on the imposed pH for typical titrations (magnesium(II) and copper(II)) is examined and the conditions for the feasibility of pH-stat chelatometric titrations are discussed.     

Tracer-monitored flow titrations

The feasibility of implementing tracer-monitored titrations in a flow system is demonstrated. A dye tracer is used to estimate the instant sample and titrant volumetric fractions without the need for volume, mass or peak width measurements. The approach was applied to spectrophotometric flow titrations involving variations of sample and titrant flow-rates (i.e. triangle programmed technique) or concentration gradients established along the sample zone (i.e. flow injection system). Both strategies required simultaneous monitoring of two absorbing species, namely the titration indicator and the dye tracer. Mixing conditions were improved by placing a chamber with mechanical stirring in the analytical path aiming at to minimize diffusional effects. Unlike most of flow-based titrations, the innovation is considered as a true titration, as it does not require a calibration curve thus complying with IUPAC definition. As an application, acidity evaluation in vinegars involving titration with sodium hydroxide was selected. Phenolphthalein and brilliant blue FCF were used as indicator and dye tracer, respectively. Effects of sample volume, titrand/titrant concentrations and flow rates were investigated aiming at improved accuracy and precision. Results were reliable and in agreement with those obtained by a reference titration procedure.     

多元校正流动注射电位滴定法同时测定苯甲酸和山梨酸

将流动注射应用于酸碱电位滴定分析,建立了一种可同时测定混合有机酸的电位滴定新方法。在该方法中,用氢氧化钠与氯化钾的混合溶液作为滴定剂,在流通池中同时插入pH指示电极和氯离子指示电极,在滴定过程中的任一滴定点,流出液的pH值和酸碱的混合比例可由两个电极的电位测定值同时获得,从而可应用多元校正法由相应的滴定曲线求得混合酸中每一种组分的含量。该方法不仅免去了体积和时间读数,而且减少了试剂和样品的消耗量,分析速度快。应用该方法对混合样品中的苯甲酸和水杨酸进行同时测定,其相对标准偏差分别为0．19％～0．37％,回收率分别为97．3％～102．6％。