Pressurized liquid extraction of pharmaceuticals from sewage-sludge

A method for the quantitative determination of ten pharmaceuticals in sewage sludge was developed by using pressurized liquid extraction (PLE) and HPLC-MS with ESI (HPLC-(ESI)MS). The PLE was optimized with regard to solvents and operational parameters, such as temperature, pressure, extraction time, and purge time. The optimum conditions were: 50 mM phosphoric acid/methanol (1:1 v/v) as the extraction solvent, temperature of 100 degrees C, pressure of 100 bar, extraction time 15 min, 2 cycles, flush volume 150% and purge time 300 s. All recoveries for pharmaceuticals were over 68% except for salicylic acid. The repetitivity and reproducibility between days expressed as RSD was lower than 8% for repetitivity and 10% for reproducibility. The LOD of all compounds was lower than 10 microg/kg of dry weight of sewage sludge. The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants (STPs). The samples were collected every three months between February 2004 and June 2005. Some pharmaceuticals were determined in the samples and naproxen showed the highest value (242 microg/kg of dry weight).     

Selective extraction of sulfonamides, macrolides and other pharmaceuticals from sewage sludge by pressurized liquid extraction

A method for the quantitative determination of three macrolides, five sulfonamides, ranitidine, omeprazole and trimethoprim in sewage sludge samples was developed by using pressurized liquid extraction and high-performance liquid chromatography-electrospray ionization mass spectrometry. The extraction solvent and such operational parameters as temperature, pressure, extraction time and purge time were optimized in pressurized liquid extraction. The experimental conditions were: an extraction solvent of water (pH 3):methanol (1:1, v/v), a temperature of 80 degrees C, a pressure of 1500 psi, a sample weight of 5 g, an extraction time of 5 min, one cycle, a flush volume of 60% and a purge time of 120 s. All recoveries were over 74%, except those for ranitidine whose value was 54%. The repeatability and reproducibility between days expressed as relative standard deviation (n = 3) were lower than 11% and 15%, respectively. The limit of detection values ranged from 2 to 11 microg/kg dry weight (d.w.). The method was applied to determine the pharmaceuticals in sewage sludge from two domestic sewage treatment plants. Roxithromycin and tylosin were determined in the samples and tylosin showed the highest value (4.0 mg/kg d.w.).     

Multi-class determination of antimicrobials in meat by pressurized liquid extraction and liquid chromatography-tandem mass spectrometry

A multi-residue method using pressurized liquid extraction (PLE) and liquid chromatography-tandem mass spectrometry (LC-MS/MS) has been developed for determining trace levels of 31 antimicrobials, including beta-lactams, lincosamides, macrolides, quinolones, sulfonamides, tetracyclines, nitroimidazoles and trimethoprim. The extraction method required pre-homogeneization of the meat with EDTA-washed sand and subsequent one-static-cycle extraction for 10 min with 40 ml of water at 1500 psi and 70 degrees C. The effect of operation temperature, pressure, flush volume, and static cycles on PLE performance was studied. Average recoveries ranged from 75 to 99% with relative standard deviations <18%. The method was validated according to the European Union requirements (2002/657/EC). In addition to the quality parameters included in that decision, the limits of detection (LODs) and quantification (LOQs) were determined. The use of LC-MS/MS provided LODs (between 3 and 15 microg kg(-1)) and LOQs (between 10 and 50 microg kg(-1)), by far lower than half of their maximum residue limits (MRLs) (between 50 and 1200 microg kg(-1)). Confirmation of the presence of any of the studied compounds was accomplished in 1h after sample receipt. This methodology has been successfully applied to the analysis of cattle and pig tissue samples from local markets and slaughterhouses of the Valencian Community (Spain). The results showed the presence of some antimicrobials at different concentrations. Quinolones and tetracyclines were the antimicrobials most detected in cattle and pig samples, respectively. Sulfonamides were also frequently detected in both types of samples.     

Determination of pharmaceuticals in biosolids using accelerated solvent extraction and liquid chromatography/tandem mass spectrometry

An analytical method was developed to quantitatively determine pharmaceuticals in biosolid (treated sewage sludge) from wastewater treatment plants (WWTPs). The collected biosolid samples were initially freeze dried, and grounded to obtain relatively homogenized powders. Pharmaceuticals were extracted using accelerated solvent extraction (ASE) under the optimized conditions. The optimal operation parameters, including extraction solvent, temperature, pressure, extraction time and cycles, were identified to be acetonitrile/water mixture (v/v 7:3) as extraction solvent with 3 extraction cycles (15 min for each cycle) at 100 °C and 100 bars. The extracts were cleaned up using solid-phase extraction followed by determination by liquid chromatography coupled with tandem mass spectrometry. For the 15 target pharmaceuticals commonly found in the environment, the overall method recoveries ranged from 49% to 68% for tetracyclines, 64% to 95% for sulfonamides, and 77% to 88% for other pharmaceuticals (i.e. acetaminophen, caffeine, carbamazepine, erythromycin, lincomycin and tylosin). The developed method was successfully validated and applied to the biosolid samples collected from WWTPs located in six cities in Michigan. Among the 15 target pharmaceuticals, 14 pharmaceuticals were detected in the collected biosolid samples. The average concentrations ranged from 2.6 μg/kg for lincomycin to 743.6 μg/kg for oxytetracycline. These results indicated that pharmaceuticals could survive wastewater treatment processes, and accumulate in sewage sludge and biosolids. Subsequent land application of the contaminated biosolids could lead to the dissemination of pharmaceuticals in soil and water environment, which poses potential threats to at-risk populations in the receiving ecosystems.     

Determination of pharmaceuticals, iodinated contrast media and musk fragrances in sludge by LC/tandem MS and GC/MS

Analytical methods have been developed that allow for the determination of antiphlogistics, lipid regulators, the antiepileptic carbamazepine, cytostatic agents, the psychiatric drug diazepam and iodinated contrast media (ICM) as well as two major polycyclic musk fragrances HHCB (galaxolide) and AHTN (tonalide) in activated and digested sludge. The procedures consist of ultrasonic solvent extraction (USE) using methanol/acetone or pressurized liquid extraction (PLE) using 100% methanol. Clean-up was performed with C18ec material and silica gel followed by LC tandem MS (electrospray or atmospheric pressure chemical ionization) detection for pharmaceuticals and iodinated contrast media as well as GC/MS in the SIM mode for musk fragrances. Absolute recoveries from spiked activated sludge in general ranged from 88+/-4 to 119+/-20% for ICM and were 78+/-15 and 87+/-10% for the AHTN and HHCB, respectively. For the pharmaceuticals, absolute recoveries in activated sludge ranged between 43 and 78%. Subsequently, compensation of losses was carried out by using surrogate standards (acidic pharmaceuticals: fenoprop, neutral pharmaceuticals: dihydro-carbamazepine, musk fragrances: AHTN-D3). With one exception the recoveries were also adequate in digested sludge ranging from 43% to 120%.     

Determination of bisphenol A in sewage effluent and sludge by solid-phase and supercritical fluid extraction and gas chromatography/mass spectrometry

Methods have been developed for the determination of bisphenol A (BPA) residues in municipal sewage and sludge samples. BPA in wastewater samples was enriched with a C18 solid-phase extraction cartridge, eluted with acetone, and converted to the pentafluoropropionyl derivative. For sludge samples, BPA was acetylated and extracted with supercritical carbon dioxide. In both cases, BPA-d16 was used as a surrogate to monitor extraction efficiency. Final analyses of derivatized sample extracts were performed by gas chromatography/mass spectrometry operating in the electron impact mode. For water samples, mean recoveries and standard deviations were 89 +/- 6, 94 +/- 4, and 85 +/- 7% at fortification levels of 1, 0.1, and 0.025 microg/L, respectively, with a method detection limit of 0.006 microg/L. For solid waste samples, mean recoveries and standard deviations were 93 +/- 5 and 92 +/- 6% at fortification levels of 2.5 and 0.25 microg/g, respectively, and the method detection limit was 0.05 microg/g. For the Canadian samples under investigation, concentrations of BPA ranged from 49.9 to 0.031 microg/L in sewage influent and effluent, and from 36.7 to 0.104 microg/g in sludge.     

A new sample preparation method for determination of acidic drugs in sewage sludge applying microwave assisted solvent extraction followed by gas chromatography-mass spectrometry

This paper presents a new sample preparation procedure for determination of selected acidic pharmaceuticals (ibuprofen, naproxen, ketoprofen, and diclofenac) in sewage sludge using microwave assisted solvent extraction, dispersive matrix extraction (DME) followed by the conventionally applied solid phase extraction (SPE), derivatization, and gas chromatography-mass spectrometry. The recoveries calculated from analytical data of spiked sludge samples changed in the range of 80-105% ± 15% for the four pharmaceuticals in mixed and activated sludge depending on the efficiency of the clean-up procedure. The measured concentration values of ibuprofen and naproxen were identical in the mixed and the activated sludge samples. However, ketoprofen and diclofenac showed about twice as high concentration in activated sludge than in the mixed one independently of the applied extraction method. The typical concentration ranges of ibuprofen, naproxen, ketoprofen and diclofenac in sewage sludge were 10-30 ng/g, 30-50 ng/g, 50-130 ng/g, and 50-140 ng/g respectively.     

Simultaneous determination of macrolides, sulfonamides, and other pharmaceuticals in water samples by solid-phase extraction and LC-(ESI) MS

This paper describes a method for determining 11 pharmaceuticals in various water sources by SPE followed by LC-(ESI) MS. SPE was carried out with Oasis HLB and the recoveries were 33-67% for 250 and 100 mL sewage water, 55-77% for 500 mL river water and 72-98% for 1 L tap water, with the exception of sulfamethoxazole and omeprazole which showed lower recoveries in all kinds of sample. The LODs in river water were of 5 ng/L for sulfadiazine, trimethoprim, sulfamethazine, sulfamethoxazole, and ranitidine and 10 ng/L for the other compounds. The highest concentrations found in river waters were for sulfamethoxazole (50 ng/L). In influent sewage waters, ranitidine was the most commonly detected compound with a maximum value of 0.24 microg/L.     

Determination of natural and synthetic estrogens and their conjugates in sewage sludge by pressurized liquid extraction and liquid chromatography-tandem mass spectrometry

In this study we present a pressurized liquid extraction/liquid chromatography-tandem mass spectrometry (PLE/LC-MS-MS) method to determine a group of estrogens and conjugated estrogens in sewage sludge. Parameters that affect the extraction step such as extraction solvent, temperature, pressure, static extraction time, number of cycles, purge time and flush volume have been optimized. In the LC-MS-MS system, electrospray ionization and a triple quadrupole analyzer have been used, and the multiple reaction monitoring mode has enabled low levels of target analytes to be detected. All recoveries were higher than 81% except for estrone 3-glucoronide and estradiol 17-glucoronide which were not extracted and consequently, they were not considered in the present study. The repeatability and reproducibility between days expressed as %RSD (n=3), were lower than 6% and 9%, respectively. The method developed allowed the target analytes to be quantified at low levels of microg/kg. The limits of detection were lower than 26 microg/kg of dry weight (d.w.) of sewage sludge, except for 17 alpha-estradiol, 17beta-estradiol, 17 alpha-ethinylestradiol and estradiol 17-acetate whose values were between 150 and 175 microg/kg (d.w.). The method was applied to determine these compounds in sewage sludge from two domestic sewage treatment plants. Estrone 3-sulfate, estradiol 3-sulfate, diethylstilbestrol, estrone and estriol were determined in some samples and estriol showed the highest value (406 microg/kg d.w.).     

Mixed aggregate-based acid-induced cloud-point extraction and ion-trap liquid chromatography-mass spectrometry for the determination of cationic surfactants in sewage sludge

Alkyl ammonium surfactants were extracted and concentrated from sludge samples using the acid-induced cloud-point extraction (ACPE) technique. Reversed-phase liquid chromatography-electrospray ionization in positive ion mode ion-trap mass spectrometry was then used for the separation, quantitation and identification of single homologues of the cationic surfactants. Variables affecting the ACPE efficiency were optimized using a spiked activated sludge. Total method recoveries ranged from 91 to nearly 100%. Detection limits for cationics in the sludge were between 40 and 75 ng/g. The analysis of cationic surfactants in activated and dehydrated sludge collected from two different sewage treatment plants revealed the presence of dialkyldimethyl, alkylbenzyldimethyl and alkyltrimethyl ammonium in the concentration range from 0.1 to 34 mg/kg. Alkylpyridinium surfactants were not detected. The persistence of alkyl ammonium surfactants in sewage sludge after treatments applied at municipal sewage plants was confirmed.     

GC-MS analysis of organic compounds in wastewater and sewage sludge

A multimethod based on liquid-liquid extraction and solid-liquid extraction for the analysis of persistent organic pollutants in water and sludge from sewage treatment plants has been established. Traces of 22 organic compounds used in industry and personal care products (PCPs) were analyzed by GC/MS. The LODs for the analytes were less than 2.3 ng/L for wastewater and 31 microg/kg (dry weight matter) for sewage sludge. Satisfactory recoveries (70-130%) were achieved. The validated method permits the analysis of water and sludge samples at various stages of the treatment from different sewage treatment plants. Thus, the distribution between water and sludge as well as the dissipation of the compounds analyzed were balanced. By this means, the efficiency of different wastewater treatment plants (WWTPs) can be evaluated and measures can be taken to optimize the treatment process at different stages.     

气相色谱-质谱法分析蜂蜜中的多种农药残留

开展了蜂蜜中23种农药残留的气相色谱-电子轰击离子源质谱(GC-EI/MS)分析方法的研究,并对其中3种农药的EI/MS碎片离子的断裂机理与结构进行了初步解析。探讨了蜂蜜试样前处理条件的优化与选择。将蜂蜜试样用乙酸乙酯提取剂超声提取、Florisil硅藻土色谱柱净化和正己烷-乙酸乙酯(体积比为7∶3)混合洗脱剂洗脱后,以PCB103为内标物,采用选择离子监测(SIM)方式下的GC-EI/MS分析。当试样的加标浓度为50,100和200 μg/kg时,加标回收率为82%～120%,相对标准偏差小于11.0%。23种农药的检测限都小于10.0 μg/kg,线性范围为10～500 μg/kg,相关系数都大于0.995。此分析方法已成功地应用于蜂蜜中23种痕量农药残留的分析。     

Determination of chlormequat and mepiquat in pear,tomato, and wheat flour using on-line solid-phase extraction (Prospekt) coupled with liquid chromatography-electrospray ionization tandem mass spectrometry

A new methodology based on pressurized liquid extraction (PLE) followed by LC-MS is presented for the simultaneous and unequivocal determination of alkylphenol ethoxylates (APEOs) and their degradation products, alkylphenols (APs) and alkylphenoxy carboxylates (APECs), in sediment samples. The protocol, applicable to a full range of APEO oligomers and degradation products, permits the sensitive and selective determination of APEOs (nEO = 1-15), APECs (nEO = 0-1) and APs at low ppb levels (LODs = 1-5 microg/kg) in sediment samples. Optimization of the operational parameters of PLE clearly demonstrates that significant thermal losses of APs occur during extraction at elevated temperatures. The loss of octylphenol (OP) at 100 degrees C was 61.2% and of nonylphenol (NP) 40.0%, whereas other compounds were completely recovered. Thus, to avoid losses due to the volatility of alkylphenols, a low extraction temperature should be applied. The conditions that gave the best results for all target compounds were as follows: extraction solvent mixture, methanol-acetone (1:1, v/v); temperature, 50 degrees C; pressure, 1500 p.s.i.; two static cycles. Using PLE and a subsequent clean-up with solid-phase extraction (SPE), the simultaneous extraction of APEOs, APs and APECs from sediment samples was achieved yielding recoveries >70% and producing low MS background noise. The developed methodology was applied on a routine basis to the analysis of alkylphenolic compounds in sediment samples. APEOs and their persistent degradation products were detected in significant concentrations in sediments from Portuguese rivers, especially at sites situated in the proximity of industrial plants (mainly the textile industry). The total concentration of alkylphenolic compounds (APEOs+APs+APECs) ranged from 155 to 2400 microg/kg. Of all the alkylphenolic compounds, NP comprised 40 to 50% with concentrations up to 1172 microg/kg.     

Determination of pharmaceuticals from various therapeutic classes in dewatered sludge by pressurized liquid extraction and high performance liquid chromatography and tandem mass spectrometry (HPLC-MS/MS)

Pharmaceuticals are released to the environment after human and animal consumption, which partly comes from accumulation in sewage sludge during wastewater treatment. This paper developed a method for the determination of N,N-diethyl-meta-toluamide (DEET) and 14 pharmaceuticals belonging to multiple therapeutic classes such as antibiotic, anti-inflammatory, antilipidemic, anti-hypertensive, and anticonvulsant in dewatered sludge. Pressurized liquid extraction using methanol/McIlvaine buffer (volume ratio, 1?:?1), associated with HPLC-MS/MS was proven to be effective for extraction and quantification of pharmaceuticals and DEET in dewatered sludge. Optimization procedures, including extraction method, extraction solvents and clean-up treatment, were carried out by simulating naturally aged samples to provide a more realistic extraction than previous methods, which were often done by spiking the standard solution before extraction without any aging procedures. The internal standard quantification method using six isotopically labelled compounds was applied to improve the poor absolute recoveries induced by severe matrix effects to obtain better relative recoveries (70–120%). Good relative standard deviations (lower than 19.0% for 7 repeats) and the limit of quantification (0.6–19.4?µg/kg) indicated that the developed method was reliable and sensitive to extract and quantify the studied pharmaceuticals in dewatered sludge. For samples collected from eight sewage treatment plants in Beijing, China, it was found that trimethoprim, caffeine, ketoprofen and ibuprofen were the most prominent contaminants, with the median concentrations reaching 97.6, 179.4, 268.0 and 153.0?µg/kg, respectively. The level of ketoprofen, ibuprofen, mefenamic acid, cabamazepine and diclofenac were similar to results reported from Spain, whilst the levels of other compounds were similar to those found in Germany, Canada and the US.     

Dispersive solid‐phase extraction followed by vortex‐assisted dispersive liquid–liquid microextraction based on the solidification of a floating organic droplet for the determination of benzoylurea insecticides in soil and sewage sludge

A novel dispersive solid‐phase extraction combined with vortex‐assisted dispersive liquid–liquid microextraction based on solidification of floating organic droplet was developed for the determination of eight benzoylurea insecticides in soil and sewage sludge samples before high‐performance liquid chromatography with ultraviolet detection. The analytes were first extracted from the soil and sludge samples into acetone under optimized pretreatment conditions. Clean‐up of the extract was conducted by dispersive solid‐phase extraction using activated carbon as the sorbent. The vortex‐assisted dispersive liquid–liquid microextraction based on solidification of floating organic droplet procedure was performed by using 1‐undecanol with lower density than water as the extraction solvent, and the acetone contained in the solution also acted as dispersive solvent. Under the optimum conditions, the linearity of the method was in the range 2–500 ng/g with correlation coefficients (r) of 0.9993–0.9999. The limits of detection were in the range of 0.08–0.56 ng/g. The relative standard deviations varied from 2.16 to 6.26% (n = 5). The enrichment factors ranged from 104 to 118. The extraction recoveries ranged from 81.05 to 97.82% for all of the analytes. The good performance has demonstrated that the proposed methodology has a strong potential for application in the multiresidue analysis of complex matrices.     

Simultaneous determination of the endocrine disrupting compounds nonylphenol, nonylphenol ethoxylates, triclosan and bisphenol A in wastewater and sewage sludge by gas chromatography-mass spectrometry

An integrated analytical method for the simultaneous determination of 4-n-nonylphenol (4-n-NP), nonylphenol monoethoxylate (NP1EO), nonylphenol diethoxylate (NP2EO), bisphenol A (BPA) and triclosan (TCS) in wastewater (dissolved and particulate phase) and sewage sludge was developed based on gas chromatography-mass spectrometry. Chromatographic analysis was achieved after derivatization with bis(trimethylsilyl)trifluoroacetamide (BSTFA). Extraction from water samples was performed by solid-phase extraction (SPE). The optimization of SPE procedure included the type of sorbent and the type of the organic solvent used for the elution. Referred to solid samples, the target compounds were extracted by sonication. In this case the optimization of the extraction procedure included the variation of the amount of the extracted biomass, the duration and the temperature of sonication and the type of the extraction organic solvent. The developed extraction procedures resulted in good repeatability and reproducibility with relative standard deviations (RSDs) less than 13% for all the tested compounds for both types of samples. Satisfactory recoveries were obtained (>60%) for all the compounds in both liquid and solid samples, except for 4-n-NP, which gave recoveries up to 35% in wastewater samples and up to 63% in sludge samples. The limits of detection (LODs) of the target compounds varied from 0.03 (4-n-NP) to 0.41 microg l(-1) (NP2EO) and from 0.04 (4-n-NP) to 0.96 microg kg(-1) (NP2EO) for liquid and solid samples, respectively. The developed methods were successfully applied to the analysis of the target compounds in real samples.     

Comparison of two extraction methods for the analysis of per- and polyfluorinated chemicals in digested sewage sludge

A rapid and reliable analytical method, based on ion-pair extraction, clean-up on Envicarb cartridge and detection by liquid chromatography–tandem mass spectrometry (LC–MS/MS), was developed for determination of 17 per- and polyfluorinated chemicals (PFCs) in digested sewage sludge. Envicarb cartridge and six labeled internal standards were selected for the elimination/reduction and correction of matrix effects, respectively. As a result, the matrix effect for perfluorooctane sulfonamides (FOSAs) and perfluorocarboxylic acids (PFCAs) with carbon chain length from C6 to C14 was lowered to a range of −14% to +28%. However, the matrix effect for other analytes was still great mainly due to the absence of appropriate internal standard. Mean recoveries of the target analytes based on matrix spikes, at different spike levels (10–300 ng/g), ranged from 70% to 169%. Relative standard deviations (RSDs) were in the range of 2–20% at different spike levels. The limit of quantification (LOQ) ranged between 0.6 and 30 ng/g. The method was successfully applied to several sewage sludge samples from wastewater treatment plants nearby Zürich, Switzerland. In addition, by comparing the accuracy and precision of ion-pair extraction method and methanol extraction method, we further demonstrated that the ion-pair extraction method can be used for the analysis of PFCs in sludge samples. To our knowledge, this is the first study to extract the PFCs in sewage sludge with ion-pair method and to find unsaturated fluorotelomer carboxylic acids (FTUCAs) in sewage sludge.     

Concurrent extraction,clean‐up,and analysis of polybrominated diphenyl ethers,hexabromocyclododecane isomers,and tetrabromobisphenol A in human milk and serum

A method has been developed and validated for the concurrent extraction, clean‐up, and analysis of polybrominated diphenyl ethers (PBDEs), α‐, β‐, and γ‐hexabromocyclododecane (HBCD), and tetrabromobisphenol A (TBBPA) in human milk and serum. Milk and serum samples were extracted using accelerated solvent extraction with acetone/hexane 1:1, v/v and liquid–liquid extraction with methyl‐tert‐butyl ether/hexane 1:1, v/v, respectively. The removal of co‐extracted biogenic materials was achieved by gel permeation chromatography followed by sulfuric acid treatment. The fractionation of the PBDEs and HBCD/TBBPA was performed using a Supelco LC‐Si SPE cartridge. The detection of the PBDEs was then performed by GC–MS and that of the HBCDs and the TBBPA was performed using UPLC–MS/MS. The pretreatment procedure was optimized, and the characteristic ions and fragmentation of the analytes were studied by MS or MS/MS. A recovery test was performed using a matrix spiking test at concentrations of 0.05–10 ng/g. The recoveries ranged from 78.6–108.8% with RSDs equal to or lower than 14.04%. The LODs were 1.8–60 pg/g. The usefulness of the developed method was tested by the analysis of real human samples, and several brominated flame retardants in different samples were detected and analyzed.     

Active single-drop microextraction for the determination of gaseous diisocyanates

Heterocyclic amines (HAs) were analysed in meat extract samples using a new method based on pressurised liquid extraction (PLE) and liquid chromatography-tandem mass spectrometry. This method combines the use of a pressurised fluid with a triple quadrupole MS/MS system, resulting in benefits from both systems: high extraction efficiency and sensitivity. The effects of solvent type and PLE operational parameters, such as temperature and extraction time, were studied to obtain maximum recovery of the analytes with minimum contamination. HA extraction was best achieved using dichloromethane/acetone (50/50, v/v) at 80 degrees C for 10 min. Recoveries ranged from 45% to 79% with good quality parameters: limit of detection values between 0.02 and 1 ng g(-1), linearity (r(2)>0.997), and run-to-run and day-to-day precisions with relative standard deviations lower than 13% achieved at both low (0.20 microg g(-1)) and medium (1.0 microg g(-1)) concentrations. This method reduces sample manipulation and total extraction time by nearly four-fold compared to conventional solid phase extraction. The optimised method was validated using laboratory reference material based on a meat extract, and was successfully applied to HA analysis in several cooked beef samples.     

Semiquantitative determination of residues of amphetamine in sewage sludge samples

A procedure based on HPLC and mass spectrometric detection has been developed for screening of residues of the illicit drug amphetamine in sewage sludge. Sample pretreatment consisted in extraction by 50 mM formic acid and methanol (80:20 v/v), followed by adjustment of the pH to 10 and preconcentration by SPE at poly(di-vinylbenzene)-N-vinylpyrrolidone. HPLC separation of the extract was done on a C18 RP with a mixture of 50 mM formic acid and methanol (80:20 v/v) as mobile phase. The mass spectrometer was operated in the MS2 and MS3 mode using the transition from m/z 136 to 119 and from m/z 119 to 91. Due to the complex matrix, ionization suppression effects as well as shifts in the sensitivity of the detector within a series of runs could not be fully excluded. Therefore, quantitation was done by standard addition together with external standards, so that semiquantitative results could be obtained down to concentrations of 2 microg/kg sewage sludge. Samples taken from various municipal sewage treatment plants indicate that amphetamine residues are ubiquitous in urban areas.