Nanocharacterization and nanofabrication of a Nafion thin film in liquids by atomic force microscopy

We demonstrated the nanocharacterization and nanofabrication of a Nafion thin film using atomic force microscopy (AFM). AFM images showed that the Nafion molecules form nanoclusters in water, in 5% methanol, and in acetic acid. Young's modulus E of a Nafion film was estimated by sequential force curve measurements in water and in 5% methanol on one sample surface. Ewater/E5% methanol was 1.75 +/- 0.40, so the film was much softer in 5% methanol than in water. Even when solvent was replaced from 5% methanol to water, Young's modulus was not recovered soon. We showed the first example of the mechanical properties of a Nafion film on the nanoscale. Furthermore, we succeeded in fabricating 3D nanostructures on a Nafion surface by AFM nanolithography in liquids. Our results showed the new potential of the AFM nanolithography of a polymer film by softening the molecules in liquids.     

Comparison of the Stability of Functionalized GaN and GaP

Surface functionalization via 1 H,1 H,2 H,2H‐perfluoro octanephosphonic acid was done in the presence of phosphoric acid to provide a simplified surface passivation technique for gallium nitride (GaN) and gallium phosphide (GaP). In an effort to identify the leading causes of surface instabilities, hydrogen peroxide was utilized as an additional chemical modification to cap unsatisfied bonds. The stability of the surfaces was studied in an aqueous environment and subsequently characterized. A physical characterization was carried out to evaluate the surface roughness and water hydrophobicity pre and post stability testing via atomic force microscopy and water goniometry. Surface‐chemistry changes and solution leaching were quantified by X‐ray photoelectron spectroscopy and inductively coupled plasma mass spectrometry. The results indicate a sensitivity to hydroxyl terminated species for both GaN and GaP under aqueous environments, as the increase of the degree of leaching was more significant for hydrogen peroxide treated samples. The results support the notion that hydroxyl species act as precursors to gallium oxide formation and lead to subsequent instability in aqueous solutions.     

Preparation and characterization of poly(l-histidine)/poly(l-glutamic acid) multilayer on silicon with nanometer-sized surface structures

The specific design and modification of surfaces is of great interest, especially for functional surfaces and medical applications. In order to obtain films on a surface, the layer-by-layer deposition of polyelectrolytes represents a well-established methodology. The alternating deposition of poly(l-histidine) and poly(l-glutamic acid) results in a defined, continuous surface coating that was thoroughly characterized using X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, ellipsometry, X-ray reflectometry, atomic force microscopy, scanning electron microscopy, contact angle, and electrokinetic measurements. Surface charge, film growth, and final thickness were measured and cross-validated. Additionally, the chemical composition and distribution of polyelectrolytes in the layerstack were determined. Finally, the optical parameters were specified and the surface topography was visualized by several methods. These characterizations revealed a coating with embedded spheroids forming from the bottom layers. This rough surface formed by (PLH/PGA)(8) was highly reproducible and might provide unique features for the design of tailored surfaces.     

Local probe and conduction distribution of proton exchange membranes

Proton exchange membranes (Nafion) have been studied using current sensing atomic force microscopy to examine the correlation between the surface morphology and the ionic domains, and to probe the local ionic conduction distribution in the membranes. It is found that the local ionic conduction generated from the current sensing images follows a Gaussian-like distribution, with the peak value and the width of the distribution increasing with the relative humidity in the sample chamber and, thus, the water content in the membranes. Two types of Nafion membranes, Nafion 112 and Nafion 117, were studied using the method. The implications of the distribution in relation to the ionic conducting channels in the membranes are discussed.     

Characterization of the novel ETFE-based membrane

Recently developed ETFE-SA membrane (sulphonated poly(ethylene-alt-tetrafluoroethylene)) has proved to be chemically stable in the direct methanol fuel cell (DMFC). According to methanol permeability measurements, the MeOH permeability through the ETFE-SA membrane is less than 2% of the corresponding value of the Nafion^® membranes. The characterization of the ETFE-SA membranes is done with sophisticated microscopy techniques. The electrochemical inhomogeneity of the membranes is investigated with the scanning electrochemical microscopy (SECM) by mapping proton distribution across the membrane surface. The atomic force microscopy (AFM) is used, when the surface morphology and morphology changes originating from swelling are investigated, while with the scanning electron microscopy (SEM), the composition and the structure of the membranes can be clarified in detail. The sulphur profile along the membrane cross-section gives information about the distribution of sulphonic acid groups and it is detected with the SEM combined with a energy dispersive X-ray spectrometer. Surface hydrophobicity is investigated by water contact angle (CA) measurement. Many remarkable structural differences between different samples are observed during the measurements, e.g. the surface roughness of the ETFE-SA membrane is much higher, when compared to the Nafion^® membranes. Altogether, the surface properties of the ETFE-SA and the Nafion^® membranes are found to differ significantly from each other and the properties of ETFE-SA vary also as a function of manufacturing parameters.     

Methanol vapor‐induced morphology and current–voltage characteristic changes in a cast‐coated nafion film/interdigitated microarray electrode

Methanol vapor‐induced membranous changes in a cast‐coated Nafion thin film were studied through current–voltage (I–V) characteristics with an interdigitated microarray (IDA) electrode and atomic force microscopy (AFM). The obtained I–V curves showed that the as‐prepared Nafion film was stable under humidified nitrogen gas; however, the I–V profile dramatically changed with exposure to methanol vapor. Next, the morphology of the film was compared before and after methanol exposure with AFM images. On the basis of our observations, we found that the as‐prepared film had an irregularly complicated microstructure, whereas the structure became homogeneous in appearance after 30 min of exposure to methanol gas. The alternating‐current conductivity data, showing almost the same magnitude before and after exposure, strongly suggested that the I–V profile shift was based on a change in an electrode reaction mechanism induced by a change in the junction at the Nafion/IDA electrode interface. Furthermore, the methanol vapor‐pre‐exposed Nafion was stable for further exposure to methanol vapor, water vapor, or both. With the stabilized film used in combination with the IDA electrode, a reversible change in the magnitude of the current was observed when the methanol/water vapor ratio was varied. This indicated that the electrode reaction had good reproducibility after the treatment. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1103–1109, 2002     

Atomic force microscopy imaging of hair: correlations between surface potential and wetting at the nanometer scale

We report investigations of hair surface potential under wetting at the nanometric scale by atomic force microscopy (AFM). Surface potential imaging was used to characterize the electrostatic properties of the hair samples. We found that the surface potential noticeably increases along the edges of the cuticles. These results are correlated with wetting behavior of different liquids performed using AFM in noncontact mode.     

Solvation of the N-(1-Phenylethyl)-N'-[3-(triethoxysilyl)propyl]-urea chiral stationary phase in mixed alcohol/water solvents

A theoretical and experimental study of alcohol/water and alcohol/alcohol solvent mixtures near a surface of N-(1-phenylethyl)-N'-[3-(triethoxysilyl)propyl]-urea (PEPU), a Pirkle-type chiral stationary phase, is presented. Molecular dynamics simulations are performed at room temperature for water/methanol, water/1-propanol, water/2-propanol, and methanol/1-propanol solvent mixtures confined between two PEPU surfaces. The interface was also prepared experimentally by attaching the PEPU molecules to atomic force microscopy tips and oxidized Si(111) substrates. Chemical force spectrometric measurements between such PEPU-terminated tips and samples were taken in the solvent mixtures, and the results are compared to the molecular dynamics study. We find that the extent of hydrogen bonding at the surface is the dominant contributor to the measured forces.     

Pd-gate MOS sensor for detection of methanol and propanol

The present paper focused on the detection of methanol and propanol using Pd-gate metal-oxide-semiconductor (MOS) sensor. Surface mor- phology and composition of the gate film were studied by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The response of the sensor for propanol and methanol was measured as shift in capacitance-voltage (C-V) and conductance-voltage (G-V) curves of the MOS structure. The sensitivity of the sensor towards methanol was found to be greater than that towards propanol. It was 58.2% for methanol and 32% for propanol (at 0.6 V, 1 MHz) in terms of capacitance measurements, while in terms of conductance results the sensitivity was found to be 57.2% for methanol and 38.9% for propanol at 1 kHz. The discontinuities or cracks present in the microstructure of the gate material are believed to be mainly responsible for the high sensitivity of the sensor, going with the decomposition of gas molecules and subsequent hydrogen permeation through Pd.     

A novel dual surface modification on titanium in dental use: Characterization and topography

This laboratory study aimed to compare, contrast, and evaluate the effect of a novel dual surface modification method on the adhesion strength of resin composite cement to titanium. C.p.-2 grade titanium samples were silica-coated, etched with HNO₃(69vol %) or a blend of HCl (35vol %) and H₃PO₄ (85vol %), for 1 h at 80°C. Surface roughness was measured by surface roughness profilometry, topographic analysis by scanning electron microscopy (SEM), atomic force microscopy (AFM), and surface analyses by energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS). Silanization of all specimens was carried out after SEM, EDX, and AFM analysis, before enclosed mold microshear bond strength testing (EM-μSBS). Adhesion strengths were measured after artificial ageing: 1 day, 1 week, 4 weeks, and 8 weeks by EM-μSBS testing and failure mode analysis by optical microscopy. Polished titanium was used as a control. The highest surface roughness was observed in titanium samples treated with silica-coating + HCl-H₃PO₄ etching. The elemental composition confirmed the presence of Ti, O, C, with Si and Al in samples treated with silica-coating. A gradual decrease in EM-μSBS values was observed in all titanium samples with adhesive and cohesive failure modes. The novel dual surface modification method applied in this study suggests that silica-coating + HCl-H₃PO₄etching strongly affects titanium surface topography and roughness. The presence of Si on silica-coated surface modified titanium before silanization with an experimental silane has a positive effect on the EM-μSBS of titanium samples treated with silica-coating only or silica-coating + HNO₃ etching.     

Super-hydrophobic, highly adhesive, polydimethylsiloxane (PDMS) surfaces

Super-hydrophobic surfaces have been fabricated by casting polydimethylsiloxane (PDMS) on a textured substrate of known surface topography, and were characterized using contact angle, atomic force microscopy, surface free energy calculations, and adhesion measurements. The resulting PDMS has a micro-textured surface with a static contact angle of 153.5° and a hysteresis of 27° when using de-ionized water. Unlike many super-hydrophobic materials, the textured PDMS is highly adhesive, allowing water drops as large as 25.0 μL to be inverted. This high adhesion, super-hydrophobic behavior is an illustration of the "petal effect". This rapid, reproducible technique has promising applications in transport and analysis of microvolume samples.     

Surface modification of titanium with thermally treated polydimethylsiloxane coating and the effect on resin to titanium adhesion

In this study, titanium surface modification by a thermal treatment using a polydimethylsiloxane (PDMS) coating was investigated. The surfaces of four titanium samples were surface treated by polishing, sandblasting, and coating with a PDMS with a thermal treatment at 800 and 1100 °C. The titanium surfaces were characterized by X‐ray photoelectron spectroscopy (XPS) and atomic force microscopy. The effect of the surface treatments on adhesion of resin to titanium was assessed by shear adhesion strength test. XPS analysis showed that there was a change of elemental composition of titanium surfaces after surface treatment. Binding energy shifts for Si2p and O1s were observed after sandblasting and thermally treated PDMS. Therefore, chemical states of Si and O were changed. Atomic force microscopy analysis revealed that the surface topography of the Ti samples was different, and surface roughness was increased after sandblasting and thermal treatment of PDMS coating. Shear adhesion strength test results showed that the adhesion between resin and titanium is affected by the treatment temperature of PDMS coating. The highest adhesion is obtained at 1100 °C (14.7 ± 1.57 MPa). Copyright © 2014 John Wiley & Sons, Ltd.     

Estimation of heterogeneous surface structure of submicron-sized,composite polymer particles consisting of hydrophobic and hydrophilic components by atomic force microscopy*

Surface structure of submicron-sized poly(styrene/2-hydroxyethyl methacrylate) [P(S/HEMA)] composite particles produced by emulsifier-free emulsion polymerization was estimated with atomic force microscopy (AFM). AFM force curves were measured in water at different points of the particle surface; it was clarified that the particle surface had a heterogeneous structure consisting of hard and soft parts, which must be, respectively, based on styrene-rich and 2-hydroxyethyl methacrylate-rich parts.     

Preparation,characterization and electrochemical properties of Nafion® doped poly(ortho-anisidine) Langmuir–Schaefer films

Langmuir–Schaefer (LS) films of poly(ortho-anisidine) (POAS) were fabricated by utilizing water and water acidified HCl as subphases, respectively. The uniformity of the films formation and the doping with Nafion were verified by UV–Vis spectroscopy. The morphology and the thickness of the POAS, HCl post-doping POAS and Nafion post-doping POAS LS films were investigated using atomic force microscopy. The electrochemical properties of POAS LS films, HCl post-doping POAS and Nafion post-doping POAS were investigated and compared with our previously published work. The electrochemical switching time of HCl post-doping POAS and Nafion post-doping POAS LS films were also estimated.     

XPS and atomic force microscopy of plasma-treated polysulfone

Surface treatment of polysulfone by O₂, H₂, He, Ne, Ar, and CF₄ nonisothermal glow discharges has been investigated by x-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The chemical and topographical modification of the surface is found to be strongly influenced by the type of feed gas employed. © 1996 John Wiley & Sons, Inc.     

Investigations of local electrical surface characteristics by dynamical scanning force microscopy

A technique is presented that allows to obtain information about sample surface topography and local electrical surface properties simultaneously. A scanning electrical force microscope is used for that purpose which is based on an atomic force microscope (AFM) working in the dynamical mode. Different information channels contained in the cantilever excitation spectrum are separated by a lock-in technique. The physical content of the technique is discussed in detail and the influence of surface topography on the non-topographic imaging is demonstrated. Finally, the real advantages of cross-sectional sample preparation (as known from electron microscopy) for this kind of scanning probe microscopy with respect to various applications is presented.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

TFC polyamide membranes modified by grafting of hydrophilic polymers: an FT-IR/AFM/TEM study

Surface modification using grafting of a hydrophilic polymer onto the membrane surface is a possible route to improving the fouling properties of polyamide thin-film composite membranes. The structure of nanofiltration (NF) and reverse osmosis (RO) membranes modified using graft polymerization of acrylic (AA) monomers was visualized and analyzed using attenuated total reflection–Fourier transform infrared spectroscopy, atomic force microscopy and transmission electron microscopy. The results show that a layer of AA polymer is indeed formed on the polyamide surface, which could be accompanied by a change of the surface morphology. It was observed that for the NF membranes studied polymerization could also take place inside the pores of the support as a result of penetration of the monomer through the active layer, particularly for high degrees of grafting. It suggests that the modification procedures should be optimized so that the latter effect is minimized.     

Characterization of SiO2 protective coatings on polycarbonate

SiO₂ protective coatings have been deposited on polycarbonate substrates by plasma ion assisted deposition. The influence of ion energy on the water permeability and the surface topography of the coatings was studied by infrared spectroscopy and atomic force microscopy. Coatings deposited at sufficiently high ion energies show a barrier effect against moisture uptake and considerably reduced film roughness. Both effects are attributed to an increase of the packing densities of the coatings.     

Cross-linking of polybutadiene at the air/water interface: toward an easy access to two-dimensional polymeric materials

A novel approach to two-dimensionally crosslink polydienes at the air/water interface is proposed. The acid-catalyzed condensation of the triethoxysilane pendant groups of triethoxysilane-functionalized polybutadiene chains at the air/water interface successfully led to the formation of an insoluble crosslinked material which could be directly removed from the water surface. The efficiency of the cross-linking reaction was demonstrated through surface pressure measurements such as surface pressure-mean molecular area isotherms recorded at different reaction times and isobar experiments for different subphase pH values. The evolution of the monolayer topography during cross-linking was studied by atomic force microscopy imaging of the Langmuir-Blodgett films.