Hydrophilic modification of poly(vinylidene fluoride) (PVDF) by in situ polymerization of methyl methacrylate (MMA) monomer

The hydrophilicity of poly(vinylidene fluoride) (PVDF) was first improved by in situ polymerization of polar monomer in PVDF solution. Methyl methacrylate was adopted as the reaction monomer, and the polymerization occurred in a solution of PVDF in N,N-dimethylformamide. PVDF/poly(methyl methacrylate) (PMMA) blend was obtained after in situ polymerization. The relative hydrophilicity of the in situ blend was characterized by contact angle measurement. At the same time, the hydrophilicity of the PVDF/PMMA blends prepared by solution blending was compared with that of the in situ blend. The contact angle measurements indicated that in situ polymerization has a stronger modifying effect on the hydrophilicity of PVDF than solution blending.     

Thermal and mechanical behavior of amorphous and semi-crystalline poly(vinylidene fluoride)/poly(methyl methacrylate) blends

Various PVDF/PMMA (poly(vinylidene fluoride)/poly(methyl methacrylate)) blends were selected for mechanical testing in compression. At low PVDF content (less than 50/50 w/w), the blends remain amorphous and PVDF and PMMA are fully miscible. In PVDF-richer blends, PVDF crystallizes in part, leading to a PMMA-enriched homogeneous amorphous phase. In this study, the degree of crystallinity was set at equilibrium by appropriate annealing of the samples before testing. Mechanical analysis was focused on the low deformation range, and especially on the yield region. Depending on the test temperature and blend composition, three types of response were identified, depending on whether plastic deformation is influenced: 1) by the PMMA secondary relaxation motions, 2) by the PVDF/PMMA glass transition motions, or 3) by the crystallite-constrained PVDF chains.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride) (PVDF)/poly(methylmethacrylate) (PMMA)/poly(styrene-<Emphasis Type="Italic">co</Emphasis>-acrylonitrile) (SAN) ternary blends

Compatibilization of the partially miscible poly(vinylidene fluoride) (PVDF)/poly(styrene-co-acrylonitrile) (SAN) pair by a third homopolymer, i.e., poly(methyl methacrylate) (PMMA), was investigated in relation to cross section morphology, crystallization behaviors and hydrophilicity of the polyblends. Scanning electron microscopy showed a more regular and homogeneous morphology when more than 15 wt.% PMMA was incorporated. The samples presented only α phase regardless of PMMA content in the blend. As the PMMA content increased in the blends, the interactions between each component were enhanced, and the crystallization of PVDF was limited, leading to a decreasing of the crystallinity and the crystallite thickness. Besides, the hydrophilicity of PVDF was further improved by PMMA addition. The sample containing 15 wt.% PMMA showed a more hydrophilic property due to the more polar part of surface tension induced by PMMA addition. Observed from the cross section of the blends, the miscibility of partially miscible PVDF/SAN blends were efficiently improved by PMMA incorporation.     

Thermorheological complexity of poly(methyl methacrylate)/poly(vinylidene fluoride) miscible polymer blend: Terminal and segmental levels

Oscillatory shear rheometry data for a miscible blend of 20 wt % poly(vinylidene fluoride) (PVDF) in poly(methyl methacrylate) (PMMA) shows breakdown of time–temperature superposition for this blend. A comparison between glass transition temperature which PMMA chains sense in the blend and effective glass transition temperature of this component indicates that, the Lodge–McLeish model can describe terminal dynamics of PMMA. In addition, terminal dynamics of PVDF chains in the blend is similar to that of its pure state in agreement with the mentioned model. At segmental level, dynamic mechanical thermal analysis of four wholly amorphous blends suggests that cooperativity of molecular motions decreases upon addition of 30 and 40 wt % PVDF to PMMA. This behavior has been confirmed via calculation of degree of fragility which presumably is attributed to strong tendency of PVDF chains to self‐association rather than inter‐association with PMMA chains according to the FTIR results. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2860–2870, 2007     

Miscibility and crystallization behavior in blends of poly(methyl methacrylate) and poly(vinylidene fluoride): Effect of star‐like topology of poly(methyl methacrylate) chain

A tetraarmed star‐shaped poly(methyl methacrylate) (s‐PMMA) was synthesized via atom transfer radical polymerization with 2‐bromoisobutyryl pentaerythritol as the initiator. For comparison, a linear PMMA with the identical molecular weight (l‐PMMA) was also prepared. The blends of the two PMMA samples with poly (vinylidene fluoride) (PVDF) were prepared to investigate the effect of macromolecular topological structure on miscibility and crystallization behavior of the binary blends. The behavior of single and composition‐dependent glass transition temperatures was found for the blends of s‐PMMA with PVDF, indicating that the s‐PMMA is miscible with PVDF in the amorphous state just like l‐PMMA. The miscibility was further evidenced by the depression of equilibrium melting points. It is found that the blends of s‐PMMA and PVDF displayed the larger k value of Gordon–Taylor equation than the blends of l‐PMMA and PVDF blends. According to the depression of equilibrium melting points, the intermolecular parameters for the two blends were estimated. It is noted that the s‐PMMA/PVDF blends displayed the lower interaction parameter than l‐PMMA/PVDF blends. The isothermal crystallization kinetics shows that the crystallization of PVDF in the blends containing s‐PMMA is faster than that in the blends containing the linear PMMA. The surface‐folding free energy of PVDF chains in the blends containing s‐PMMA is significantly lower than those in the blends containing l‐PMMA. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2580–2593, 2007     

Crystallization kinetics of poly(ethylene oxide) confined in semicrystalline poly(vinylidene) fluoride

Polymer blends based on poly(vinylidene fluoride) (PVDF) and poly(ethylene oxide) (PEO) have been prepared to analyze the crystallization kinetics of poly(ethylene oxide) confined in semicrystalline PVDF with different ratios of both polymers. Both blend components were dissolved in a common solvent, dimethyl formamide. Blend films were obtained by casting from the solution at 70 °C. Thus, PVDF crystals are formed by crystallization from the solution while PEO (which is in the liquid state during the whole process) is confined between PVDF crystallites. The kinetics of crystallization of the confined PEO phase was studied by isothermal and nonisothermal experiments. Fitting of Avrami model to the experimental DSC traces allows a quantitative comparison of the influence of the PVDF/PEO ratio in the blend on the crystallization behavior. The effect of melting and further recrystallization of the PVDF matrix on PEO confinement is also studied. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 588–597     

Structural studies of radiation-crosslinked poly(ethylene oxide)

The structure and thermal behavior of freeze-dried gels of radiation-crosslinked high molecular weight poly(ethylene oxide) (PEO) were investigated by optical and electron microscopy, wide-angle x-ray scattering (WAXS), DTA, TGA, and thermomechanical analysis. The gels are highly porous with thin crystalline walls. Small spherulite and hedrite structures are observed on the walls. A model for gel formation in solution is suggested. A statistically homogenous chemical network is formed as a result of intrachain and interchain crosslinking. Simultaneous grafting of macromolecular fragments formed by chain scission also occurs. On increasing the irradiation dose from 1 to 15 Mrad, the degree of crystallinity determined by x-ray diffraction and the total intensity of diffraction gradually decrease. The temperature and enthalpy of melting diminish steeply up to 5 Mrad, fall only slightly from 5 to 8 Mrad, and do not change from 8 to 15 Mrad. By comparing the x-ray and DTA crystallinity values, this is shown to be due not only to reduced crystallinity at higher network density but also to Tree energy changes of entropic origin in crystalline and amorphous regions. Radiation chemical yields, G(-units), for these dose ranges are 100, 38, and 0, respectively. Thermomechanical analysis was used to determine the elastic modulus of compression as a function of the dose absorbed, and the average molecular weight of network chains was estimated. decreases with doses up to 10 Mrad and does not change with further irradiation.     

Composition distributions within poly(vinylidene fluoride) spherulites as grown in blends with poly(methyl methacrylate)

Upon crystalline solidification of one component in a homogeneously molten polymer blend, composition profiles develop outside (i.e., in the rest melt) and behind (i.e., within the spherulites) the crystal growth front. The present article is devoted to the detailed verification and the interpretation of these distributions and their temporal development inside growing spherulites. To this end, the energy dispersive X‐ray emission (EDX) of suitable elements has been recorded locally resolved in a scanning electron microscope and evaluated correspondingly. The investigations were performed at the melt homogeneous blend of poly(vinylidene fluoride) (PVDF) as crystallizing and poly(methyl methacrylate) (PMMA) as steadily amorphous component. If the spherulites are not volume filling, the mean PMMA content 〈?_PMMA〉 inside the PVDF spherulites is for all blends about 0.2 below the starting composition. ?_PMMA increases however slightly from the center of a spherulite to its border. That increase reflects the PMMA concentration in front of the spherulite surface, which increases likewise with time, and is clearly above the initial composition. There is at the spherulite surface, consequently, a remarkable jump in composition from the spherulite internal to its amorphous surroundings. It may amount up to 0.5. With volume filling spherulites, a slight variation of the composition from the center of a spherulite to its border is observed, too. This proves that also at these conditions composition profiles develop in the spherulite's surroundings. They remain however so weak that they do not inhibit crystallization even in its later stages. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 338–346, 2006     

PMMA/PVDF共混对PVDF的β相构型影响的研究

采用溶液法制备了不同含量的聚甲基丙烯酸甲酯/聚偏二氟乙烯(PMMA/PVDF)共混薄膜,利用傅立叶变换红外光谱(FTIR)、X射线衍射谱(XRD)、和差热分析法(DSC)对共混薄膜的结晶行为进行了分析。结果表明,共混物中PMMA的含量对PVDF的β相构型有明显影响:PMMA/PVDF=30/70共混物中β相含量最高。为提高PVDF薄膜的铁电性能提供了新的研究方法。     

Effect of gamma-ray irradiation on the mechanical strength of polystyrene-ferrocene composite

Thin films of polystyrene-ferrocene (PS---Fe) composite were irradiated with various doses of gamma irradiation ranging from 4·1 to 25·3 Mrad. The Vickers hardness number (H_v) was calculated for pure and irradiated specimens. It was used to analyse mechanical strength at a saturation load of 100 g. The mechanical strength was found to increase with irradiation dose up to 12 Mrad. Brittleness of the composite PS-Fe was found to occur at a higher dose of 25 Mrad as compared to 15 Mrad for polystyrene. Further, fracture toughness, brittleness index and yield strength were calculated for various irradiated specimens consequent to crack propagation in the specimens.     

Modification of the polycarbonate/poly(vinylidene fluoride) interface by poly(methyl methacrylate). Effect on the interfacial adhesion and interfacial tension

Polycarbonate (PC) and poly(vinylidene fluoride) (PVDF) are two immiscible polymers which form two-phase blends with weak interfacial adhesion and high interfacial tension. This situation may be changed by the addition of poly(methyl methacrylate) (PMMA), which concentrates preferably in the PVDF-rich phase, but also at the PVDF/PC interface. The interfacial activity of PMMA was estimated by the measurement of the interfacial adhesion and interfacial tension in relation to the PMMA content in the PVDF/PC blends. The interfacial adhesion between PC and homogeneous PVDF/PMMA blends of various compositions was measured by the dual cantilever beam technique. The imbedded fiber retraction method was used for the measurement of the interfacial tension. A very beneficial effect was observed when PVDF was premixed with PMMA amounts increasing up to ca. 35 wt.-%. Beyond that content, the improvement tends to level off.     

Investigation on LCST behavior of a new amorphous/crystalline polymer blend: Poly(n‐methyl methacrylimide)/poly(vinylidene fluoride)

The liquid–liquid phase‐separation (LLPS) behavior of poly(n‐methyl methacrylimide)/poly(vinylidene fluoride) (PMMI/PVDF) blend was studied by using small‐angle laser light scattering (SALLS) and phase contrast microscopy (PCM). The cloud point (T_c) of PMMI/PVDF blend was obtained using SALLS at the heating rate of 1 °C min^?1 and it was found that PMMI/PVDF exhibited a low critical solution temperature (LCST) behavior similar to that of PMMA/PVDF. Moreover, T_c of PMMI/PVDF is higher than its melting temperature (T_m) and a large temperature gap between T_c and T_m exists. At the early phase‐separation stage, the apparent diffusion coefficient (D_app) and the product (2Mk) of the molecules mobility coefficient (M) and the energy gradient coefficient (k) arising from contributions of composition gradient to the energy for PMMI/PVDF (50/50 wt) blend were calculated on the basis of linearized Cahn‐Hilliard‐Cook theory. The kinetic results showed that LLPS of PMMI/PVDF blends followed the spinodal decomposition (SD) mechanism. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1923–1931, 2008     

Conformational changes of poly(ethylene oxide) in poly(ethylene oxide)/poly(methyl methacrylate) blends by supercritical carbon dioxide

The effects of supercritical carbon dioxide (SC CO₂) fluids on the morphology and/or conformation of poly(ethylene oxide) (PEO) in PEO/poly(methyl methacrylate) (PMMA) blends were investigated by means of differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and Fourier transform infrared (FTIR). According to DSC data for a given blend, the melting enthalpy and, therefore, degree of crystallinity of PEO were increased, whereas the melting temperature of PEO was decreased, with SC CO₂ treatment. The enhancement of PEO crystallization with SC CO₂ treatment, as demonstrated by DSC data, was supported by WAXD data. According to FTIR quantitative analyses, before SC CO₂ treatments, the conformation of PEO was transformed from helix to trans planar zigzag via blending with PMMA. This helix‐to‐trans transformation of PEO increased proportionally with increasing PMMA content, with around 0.7% helix‐to‐trans transformation per 1% PMMA incorporation into the blend. For a given blend upon SC CO₂ treatments, the conformation of PEO was transformed from trans to helix. This trans‐to‐helix transformation of PEO decreased with increasing PMMA contents in the blends because of the presence of interactions between the two polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2479–2489, 2004     

Effects of electron beam irradiation on poly(butylene adipate)diol

Effects of electron beam (EB) irradiation on poly(butylene adipate)diol (PBAD) were studied by means of GPC, DSC, and X-ray diffractometry. Below 5 Mrad, chain scission predominantly occurs, while above 10 Mrad, crosslinking and chain scission take place in parallel. Structure of EB-irradiated PBAD is mainly characterized by the main reactions, degradation and crosslinking. Crystallinity of PBAD increased by EB irradiation. This phenomenon was explained by reorganization due to high molecular mobility of EB-irradiated PBAD. But, increment of crystallinity decreased with increasing dose because of formation of crosslinking, excessive degradation and thermal effect of EB. As the result, the crystallinity of EB-irradiated PBAD with a high dose becomes lower than that of original PBAD by thermal treatment.     

High breakdown strength and low loss binary polymer blends of poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) and poly(methyl methacrylate)

Dielectric materials with high breakdown strength and low loss are of crucial importance in capacitive energy storage electronics. Herein, a kind of polymer blend composed of poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) ferroelectric terpolymer and linear dielectric poly(methyl methacrylate) (PMMA) is presented. The polymer blend shows a breakdown strength of 733 MV/m and a charge‐discharge efficiency over 90% at 200 MV/m with optimized PMMA content, which are 101% and 28% higher than that of neat terpolymer. Moreover, microsecond discharge time of 2.26 μs, along with a power density that is 3.6 times that of the current commercially available biaxially oriented polypropylene, as well as great cyclic performance, has been achieved under an electric field of 200 MV/m. The findings of this research demonstrate that the incorporation of linear dielectric PMMA into poly(vinylidene fluoride)‐based ferroelectric polymer provides a new strategy in designing high breakdown strength low loss dielectric materials for reliable compact flexible film capacitors.     

Increase in crystallinity in poly(vinylidene fluoride) by electron beam radiation

We examine the influence of high-energy radiation and subsequent aging and orientation on the degree of crystallinity of poly(vinylidene fluoride) (PVDF) films. In particular, PVDF films were exposed to electron beam radiation (doses up to 50 Mrad) and aged at room temperature for varying lengths of time followed by uniaxial orientation. The degree of crystallinity of these films was found to increase significantly with increasing radiation dose. In addition, a further substantial increase in the degree of crystallinity was observed upon subsequent aging of irradiated films at room temperature. Upon orientation, in addition to a further rise in the degree of crystallinity, the crystallites were observed to undergo the α form → β form transformation, the latter phase being the polar phase effective for piezo-electric/pyroelectric activity.     

Fabrication of superhydrophilic poly(styrene-alt-maleic anhydride)/silica hybrid surfaces on poly(vinylidene fluoride) membranes

Superhydrophilic organic/inorganic hybrid surfaces have been fabricated on blend membranes of poly(vinylidene fluoride) (PVDF) and poly(styrene-alt-maleic anhydride) (SMA). The blend membranes were prepared from PVDF/SMA mixed solution with N,N-dimethylacetamide (DMAc) as solvent by immersion-precipitation phase inversion process. The gained blend membranes were immersed into γ-aminopropyltriethoxysilane (APTS) solution to generate SMA/silica hybrid surfaces by the reaction between anhydrides and APTS. The hybrid surfaces chemical compositions, morphologies and hydrophilicity were investigated in detail. It demonstrates that the hybrid surfaces possess micro-nano hierarchical structure and display superhydrophilicity property and good stability. Finally, the reaction and formation mechanism of the superhydrophilicity hybrid surface was discussed.     

Carbon nanotubes induced poly(vinylidene fluoride) crystallization from a miscible poly(vinylidene fluoride)/poly(methyl methacrylate) blend

Different contents of carbon nanotubes (CNTs) were introduced into a miscible poly(vinylidene fluoride) (PVDF)/poly(methyl methacrylate) (PMMA) blend. The interfacial affinity between CNTs and components of the blend was evaluated by calculating the interfacial tension. The dispersion and microstructure of CNTs in the nanocomposites were investigated through scanning electron microscope and rheological measurement. The effect of CNTs on the crystallization of PVDF was comparatively investigated through nonisothermal and isothermal crystallization processes. The results showed that CNTs exhibited stronger interfacial affinity to PMMA. Homogeneous dispersion of CNTs in the nanocomposites was achieved. Largely enhanced crystallization temperature and increased crystallinity of PVDF were obtained by adding CNTs during the nonisothermal crystallization process. The results obtained from the isothermal crystallization process proved that CNTs induced the concentration fluctuation in the sample, which resulted in the formation of spherulites with different types, i.e., the banded spherulites and compact spherulites. Furthermore, both the crystallization temperature and the content of CNTs exhibited great influence on the crystalline morphology of PVDF.     

Polymer blend/organoclay nanocomposite with poly(ethylene oxide) and poly(methyl methacrylate)

A series of polymer blend/organoclay nanocomposite at a fixed blending ratio was prepared using equal ratio of poly(ethylene oxide) (PEO) and poly(methyl methacrylate) (PMMA) via solvent casting method. With respect to nanoscale internal structure, we found that PMMA chains have better affinity with organoclay than PEO, based on the results from X-ray diffraction. Direct visualization via transmission electron microscopy (TEM) also supported the better affinity of PMMA with organoclay by indicating the existence of hybrid structures of mainly intercalated but with some exfoliated forms. The miscible nature of the blend and homogeneous dispersion state of layered silicate in the blend system were investigated via the microscopic fractured surface morphologies. From rheological measurements (storage and loss modulus), we discovered the role of the physical network structure between polymer and organoclay to be a main factor for the enhancement of elastic properties.     

Preparation and characterization of PVDF‐based blend membranes as polymer electrolyte membranes in fuel cells: Study of factor affecting the proton conductivity behavior

There is a huge demand especially for polyvinylidene fluoride (PVDF) and its copolymers to provide high performance solid polymer electrolytes for use as an electrolyte in energy supply systems. In this regard, the blending approach was used to prepare PVDF‐based proton exchange membranes and focused on the study of factor affecting the ir proton conductivity behavior. Thus, a series of copolymers consisting of poly (methyl methacrylate) (PMMA), polyacrylonitrile (PAN), and poly(2‐acrylamido‐2‐methyl‐l‐propanesulfonic acid) (PAMPS) as sulfonated segments were synthesized and blended with PVDF matrix in order to create proton transport sites in PVDF matrix. It was found that addition of PMMA‐co‐PAMPS and PAN‐co‐PAMPS copolymers resulted in a significant increase in porosity, which favored the water uptake and proton transport at ambient temperature. Furthermore, crystallinity degree of the PVDF‐based blend membranes was increased by addition of the related copolymers, which is mainly attributed to formation of hydrogen bonding interaction between PVDF matrix and the synthesized copolymers, and led to a slight decrease in proton conductivity behavior of blend membranes. From impedance data, the proton conductivity of the PVDF/PMMA‐co‐PAMPS and PVDF/PAN‐co‐PAMPS blend membranes increases to 10 and 8.4 mS cm⁻¹ by adding only 50% of the related copolymer (at 25°C), respectively. Also, the blend membranes containing 30% sulfonated copolymers showed a power density as high as 34.30 and 30.10 mW cm⁻² at peak current density of 140 and 79.45 mA cm⁻² for the PVDF/PMMA‐co‐PAMPS and PVDF/PAN‐co‐PAMPS blend membranes, respectively. A reduction in the tensile strength was observed by the addition of amphiphilic copolymer, whereas the elongation at break of all blend membranes was raised.