Rayleigh scattering in fused silica samples for gravitational wave detectors

Laser interferometer gravitational wave detectors require very high optical quality test masses. We report the bulk Rayleigh scattering in high quality fused silica samples. Results show that the scattering of the high quality fused silica is similar for various grades of fused silica from Heraeus. The total integrated scattering is about 0.7 ppm cm^− 1at 1064 nm wavelength, which agrees with the theoretical value calculated using known fused silica parameters. All samples show Rayleigh scattering ratio inhomogeneity of ~ 4%.     

分层半空间表面非线性瑞利波的激发*

针对非线性瑞利波在均匀分层半空间结构中的激发和传播规律进行研究。根据摄动理论和模态分解将分层半空间结构中瑞利波的二次谐波声场表示为二倍频瑞利波模式的线性组合,经由互易关系得到各模式的展开系数表达式。对不同分层半空间结构中瑞利波二次谐波的激发和传播特性进行讨论,结果表明相速度匹配的瑞利波模式其二次谐波分量随传播距离线性增长,非匹配模式的二次谐波分量则沿传播方向周期震荡传播。此外,文中定义非线性参数表征瑞利波模式产生的非线性程度,这有利于选择出具有明显非线性效应的匹配点,为后续检测工作提供理论依据,具有指导意义。     

Experimental study on the surface stress measurement with Rayleigh wave detection technique

In this paper, experimental study on the surface stress measurement of a metallic material based on the Rayleigh wave acoustoelastic theory is introduced. A Rayleigh wave acoustoelastic formula deduced by Husson is optimized to estimate the surface stress of the material. Two micro Rayleigh wave transducers with 5 MHz frequency one of which is used for acoustic pulse emitter and another for receiver are used to determine the time of flight of Rayleigh wave propagating in a certain distance along the surface of the material. The difference in time of flight between two ultrasonic signals obtained in stressed and unstressed object surface is identified by the digital correlation method. A specimen made of Q235 steel and applied with tensile load is used for calibration to obtain the acoustoelastic coefficients of Q235 steel. Furthermore, some principal factors which may result in errors in the experiment are discussed and some measurements are proposed to prevent these errors. Finally the surface stress of a cantilever beam is detected by the Rayleigh wave acoustoelastic technique and the experimental result is well compared with the theoretical value.     

Analysis of Laser-generated Rayleigh wave on viscoelastic materials

In order to understand the viscoelasticity of material, this research has been conducted to study the propagation characteristics of viscoelastic Rayleigh wave theoretically. A model is presented for the pulsed laser generation of ultrasound on viscoelastic medium surface. Referred to the Kelvin model, the frequency equation and the normal displacement of viscoelastic Rayleigh wave were derived, the influence of the viscoelastic modulus on dispersion and attenuation was discussed. From the theoretical calculation, it is shown that the effect of viscoelasticity on the attenuation of Rayleigh wave is more than that on its dispersion. In the case of a weak viscosity, the attenuation of viscoelastic Rayleigh wave is directly proportional to viscosity modulus; the effect of shear viscosity on the attenuation is much more than that of bulk viscosity. The transient response of viscoelastic Rayleigh wave was also simulated using Laplace and Hankel inversion transform, which are showed in good agreement with the theoretic predictions. The model provides a useful tool for the determination of viscoelastic parameters of medium.     

有限振幅声波间的非线性相互作用对声源远场指向性的影响

根据Fenlon理论推导得到了多频声源的辐射声压.基于单频声源谐波指向性的求解方法,得到了二阶近似下的双频声源辐射出的声波相互作用时的远场指向性.分别研究和讨论了在初始辐射声压和频率不同情况下,两列波的相互作用对其中一列波的一阶波和二阶波远场指向性的影响.结果表明,声波间的相互作用对声源远场指向性的影响根据各波之间的相对初始辐射声压和相对频率的不同而有所变化. 关键词： 有限振幅声波 非线性相互作用 远场指向性     

Surface-energy-anisotropy-induced orientation effects on Rayleigh instabilities in sapphire

Arrays of controlled-geometry, semi-infinite pore channels of systematically varied crystallographic orientation were introduced into undoped m-plane sapphire substrates using microfabrication techniques and ion-beam etching and subsequently internalized by solid-state diffusion bonding. A series of anneals at 1700 °C caused the breakup of these channels into discrete pores via Rayleigh instabilities. In all cases, channels broke up with a characteristic wavelength larger than that expected for a material with isotropic surface energy, reflecting stabilization effects due to surface-energy anisotropy. The breakup wavelength and the time required for complete breakup varied significantly with channel orientation. For most orientations, the instability wavelength for channels of radius R was in the range of 13.2R-25R, and complete breakup occurred within 2-10 h. To first order, the anneal times for complete breakup scale with the square of the breakup wavelength. Channels oriented along a direction had a wavelength of ≈139R, and required 468 h for complete breakup. Cross-sectional analysis of channels oriented along a direction showed the channel to be completely bounded by stable c(0 0 0 1), , and facets.