La substitution in four-layers Aurivillius phase SrBi4Ti4O15

Ceramics with the nominal composition of SrBi_4−xLa_xTi₄O₁₅ have been prepared within the range of 0≤x≤1.8, and the dielectric properties are investigated. Single phase SrBi_4−xLa_xTi₄O₁₅ solid solution exists until the secondary phase of La_2/3TiO₃ appears at x=1.6. The Curie temperature is 520 °C for pure SrBi₄Ti₄O₁₅, and it shifts to low temperature with increasing x, which is due to the smaller structural distortion caused by La³⁺ substitution. In addition, the dielectric constant anomaly is suppressed with the substitution. No dielectric relaxation behavior is observed. When x≥1.2, the paraelectric state is attained in the present ceramics. La³⁺ substitution effects on the SrBi₄Ti₄O₁₅ ceramics are also compared with the previous work on Bi_4−xLa_xTi₃O₁₂.     

Ferroelectric properties of Bi3.25−x/3La0.75Ti3−xNbxO12 films prepared by pulsed laser deposition

Bi₄Ti₃O₁₂ (BiT), Bi_3.25La_0.75Ti₃O₁₂ (BLT), Bi_4−x/3Ti_3−xNb_xO₁₂ (BTN) and Bi_3.25−x/3La_0.75Ti_3−xNb_xO₁₂ (BLTN) thin films have been prepared by pulsed laser deposition. BTN and BLTN films exhibit a maximum in the remanent polarization P_r at a Nb content x=0.018. At this Nb content, the BLTN film has a P_r value (25 μC/cm²) that is much higher than that of BiT and a coercive field similar to that of BiT. The polarization of this BLTN film is fatigue-free up to 10⁹ switching cycles. The high fatigue resistance is mainly due to the substitution of Bi³⁺ ions by La³⁺ ions at the A site and the enhanced P_r arises largely from the replacement of Ti⁴⁺ ions by Nb⁵⁺ ions at the B site. The mechanisms behind the effects of the substitution at the two sites are discussed.     

Synthesis and structure refinement of layered perovskites Ba5−xLaxNb4−xTixO15 (x=0, 1, 2, 3 and 4) solid solutions

Ba_5−xLa_xNb_4−xTi_xO₁₅ solid solutions were prepared by solid state reaction method. Structural analysis for the stoichiometric phases was performed for x=0, 1, 2 and 3 by Rietveld analysis of neutron powder diffraction data. The x=0, 1 and 2 members could be refined in the space group P-3m1 (stacking sequence chhcc, polytypoid 5 H). There is a decrease in cell volume as x increases. La³⁺ occupies preferentially the A2 site (Wyckoff site 2d) and Ti⁴⁺ the B2 site (Wyckoff site 2c). As x increases there is an increase of the global instability index (GII) (which is a measure of the extent to which the BVS rule is violated over the whole structure) indicating the presence of intrinsic strains large enough to cause instability at room temperature. This strain is responsible for a structural change for the member with x=3, which could be refined in the space group P-3c1 (stacking sequence (chhcc)₂, polytypoid 2×5H=10H). This change in space group is associated with a cooperative rotation of (Nb/Ti)O₆ octahedra around the c-axis, necessary to accommodate the smaller La³⁺ ion in the cuboctahedral cavity.     

Synthesis and electrochemical performances of Li4Ti4.95Al0.05O12/C as anode material for lithium-ion batteries

Spinel compounds Li₄Ti_5−xAl_xO₁₂/C (x=0, 0.05) were synthesized via solid state reaction in an Ar atmosphere, and the electrochemical properties were investigated by means of electronic conductivity, cyclic voltammetry, and charge-discharge tests at different discharge voltage ranges (0-2.5 V and 1-2.5 V). The results indicated that Al³⁺ doping of the compound did not affect the spinel structure but considerably improved the initial capacity and cycling performance, implying the spinel structure of Li₄Ti₅O₁₂ was more stable when Ti⁴⁺ was substituted by Al³⁺, and Al³⁺ doping was beneficial to the reversible intercalation and deintercalation of Li⁺. Al³⁺ doping improved the reversible capacity and cycling performance effectively especially when it was discharged to 0 V.     

Critical current density and flux pinning in La2−xPrxCa2x Ba2Cu4+2xOz (x=0.1-0.5) superconductors

Polycrystalline La_2−xPr_xCa_2xBa₂Cu_4+2xO_z (LPCaBCO) compounds with x=0.1-0.5 were synthesized by solid-state reaction method and studied by room temperature X-ray diffraction, dc resistivity, dc magnetization and iodometry. The superconducting transition temperatures in these tetragonal triple perovskite compounds increases from 32 to 62 K (T_c^onset values) with increasing dopant concentration. The mixing of rare earth La³⁺ and Pr^3+/4+ ions at rare earth site (La³⁺) along with substitution of divalent Ca²⁺ results in the shrinkage of unit cell volume. The contraction of unit cell volume due to larger ion being substituted by smaller ions, gives rise to creation of pinning centres in the unit cell leading to increase in critical current density and flux pinning.     

Influence of mobile space charges on electrical properties of ferroelectric Bi3.5La0.5Ti3O12 thin films

Lanthanum-substituted bismuth titanate, Bi_3.5La_0.5Ti₃O₁₂ (i.e., x=0.5 in Bi_4−xLa_xTi₃O₁₂), thin films have been grown on Pt/Ti/SiO₂/Si substrates using pulsed laser deposition. The frequency dependence of the real part ε′(ω) and the imaginary part ε″(ω) of the dielectric constant has been studied. The ε′(ω) does not show any sudden change within the frequency range of 10²-10⁶ Hz. In contrast, the ε″(ω) shows a large dispersion as frequency decreases. The observed relaxation behavior in ε″(ω) can be explained in terms of a migration of oxygen vacancies in (Bi₂O₂)²⁺ layers, not in Bi₂Ti₃O₁₀ perovskite layers.     

Effect of interface states associated with transitional nanophase precipitates in the enhancement of red emission from SrAl12O19:Pr by Ti incorporation

SrAl₁₂O₁₉:Pr³⁺, Ti⁴⁺ phosphor suitable for field emission displays is prepared by the wet chemical gel-carbonate method and the mechanism of enhancement in red photoluminescence (PL) intensity with Ti⁴⁺ therein has been investigated. The PL spectra of Pr³⁺ show both ¹D₂-³H₄ and ³P₀-³H₆ emission in the red region with very weak intensity when excited at 355 nm. The emission intensity has increased by about 100 times at room temperature in the compositional range SrAl_12−xTi_xO_19+x/2:Pr³⁺, with 0.1≤x≤0.3 in comparison to Ti-free SrAl₁₂O₁₉:Pr³⁺. TEM investigations show the presence of exsolved nanophase of SrAl₈Ti₃O₁₉, the precipitation of which is preceded by the presence of defect centers at the interfacial regions between the semicoherent transient phase and the parent SrAl₁₂O₁₉ matrix. The presence of transitional nanophase and the associated defects modify the excitation-emission process by way of formation of electronic sub-levels at lower energy (3.5 eV) than the band gap of SrAl₁₂O₁₉ (∼7 eV) followed by non-resonance energy transfer to Pr³⁺ level, leading to magnetic-dipole related red emission with enhanced intensity. The PL intensity of Pr³⁺ decreases at high Ti⁴⁺ concentrations (x>0.3) due to higher extent of segregation of non-emissive SrAl₈Ti₃O₁₉:Pr³⁺ phase.     

Magnetic phase diagram of double-layered La2−2xCa1+2xMn2O7 manganite

Double-layered manganite La_2−2xCa_1+2xMn₂O₇ have been synthesized for compositions ‘x’=0.0, 0.1, 0.2, 0.3, 0.4 and 0.5 by solid state reaction method. From X-ray diffraction study, their crystal structures were found to be tetragonal perovskite with lattice parameters decreasing with increasing ‘x’. The decreasing lattice parameters affect the balance between in-plane, intra-bilayer and inter-bilayer exchange interactions, which is reflected on magnetotransport properties. The metal-to-insulator transition temperature is found to vary with composition and peaked around ‘x’=0.3. From ac-susceptibility study, 2D-ferromagnetic ordering was observed at higher temperatures for all compositions whereas 3D-ferromagnetic ordering was observed at quite low temperatures. In low-temperature region, decreasing susceptibility shows antiferromagnetic state for all compositions. On the basis of electrical and magnetic properties, a magnetic phase diagram is given.     

Influence of sintering conditions and doping on the dielectric relaxation originating from the surface layer effects in CaCu3Ti4O12 ceramics

Detailed investigations into the dielectric dispersion phenomenon in the giant dielectric constant material CaCu₃Ti₄O₁₂ (CCTO) around room temperature revealed the existence of two successive dielectric relaxations. In the temperature domain, a new dielectric relaxation was clearly observed around 250 K, in addition to the well-investigated dielectric relaxation close to 100 K. The effect of sintering and doping (La³⁺) on the strength of these dielectric relaxations were studied in detail. The sintering temperature as well as its duration was found to have tremendous influence on the dielectric relaxation that was encountered around 250 K. This Maxwell-Wagner (M-W) type of relaxation was found to be originating from the surface layer containing the Cu-rich phase, which was ascribed to the difference in the oxygen content between the surface and the interior of the sample. Interestingly, this particular additional relaxation was not observed in La_2/3Cu₃Ti₄O₁₂, a low dielectric constant member of the CCTO family, in which the segregation of Cu-rich phase on the surface was absent. Indeed the correlation between the new relaxation and the presence of Cu-rich phase in CCTO ceramics was further corroborated by the absence of the same after removing the top and bottom layers.     

Ferroelectric properties of highly c-axis oriented Bi4−xLaxTi3O12 film-based capacitors

Highly c-axis oriented lanthanum-modified bismuth titanate (Bi_4−xLa_xTi₃O₁₂) films having a variety of lanthanum (La) contents were grown on Pt/TiO₂/SiO₂/Si(100) substrates using metal-organic sol deposition and subsequent annealing at 650 °C for 1 h. After systematically examining the ferroelectric properties of Bi_4−xLa_xTi₃O₁₂ films as a function of the La-content, it was concluded that the film with x=0.85 had the largest remanent polarization in the direction parallel to the c-axis. The Pt/Bi_3.15La_0.85Ti₃O₁₂/Pt capacitor showed a well-saturated polarization-electric field (P-E) switching curve with the switching remanent polarization (2P_r) value of 33 μC/cm² and the coercive field (E_c) of 68 kV/cm at an applied voltage of 10 V. More importantly, the capacitor exhibited fatigue-free behavior up to 6.5×10¹⁰ read/write switching cycles at a frequency of 1 MHz. The capacitor also demonstrated an excellent charge-retaining ability and a strong resistance against the imprinting failure.     

Room temperature magnetoresistance in Ln2/3A1/3MnO3 manganites

The investigation of the manganites La_2/3−xPr_xSr_1/3MnO₃, La_2/3Sr_1/3−xCa_xMnO₃ and La_2/3+xCa_1/3−2xAg_xMnO₃, which all exhibit Mn³⁺:Mn⁴⁺=2, shows that it is possible to reach high magnetoresistance at room temperature, up to 21% under 1.2 T. These materials are compared to La_5/6Ag_1/6MnO₃ which corresponds to the same Mn³⁺:Mn⁴⁺ ratio and exhibits a magnetoresistance of 25% in this field. An interesting feature deals with the value of the insulator-metal transition temperature T_IM, often higher than T_C, especially for Ag-based compounds. It is suggested that the latter results either from a better oxygenation of the surface of the grains or from a migration of silver toward the surface.     

Structure and magnetic properties of Ca1−x−yMgxCu2+yO3 influenced by isoelectronic substitution x

Phases of the composition Ca_1−x−yMg_xCu_2+yO₃ have been prepared for the first time. The compounds are isostructural with the known end-members CaCu₂O₃ and MgCu₂O₃ showing a two-leg spin-ladder-like connection of copper and oxygen atoms within the Cu₂O₃-layer. Opposite the spin ladders this layer is folded, which results in a long-range antiferromagnetic ordering of these phases. The Néel temperature can be adapted by variation of x in Ca_1−x−yMg_xCu_2+yO₃ between 24 and 80 K. Several structural features, which influence the magnetic ordering, are discussed.     

Dielectric properties and temperature stability of BaTiO3 co-doped La2O3 and Tm2O3

The influence of La₂O₃ and Tm₂O₃ co-doping on the dielectric properties and the temperature stability of BaTiO₃ was investigated. BaTiO₃ ceramics were prepared with the compositional formula of (Ba_1−xLa_x)(Ti_1-x/4−yTm_y)O₃. La₂O₃ and Tm₂O₃ co-doping in BaTiO₃ mainly had effects on an increase in the dielectric constant and the temperature stability, respectively. The increase of La₂O₃ concentration and the decrease of Tm₂O₃ concentration in BaTiO₃ resulted in a decrease of lattice parameter and tetragonality because La³⁺ ion substituting for Ba site is smaller than Ba²⁺ ion and Tm³⁺ ion substituting for Ti site is larger than Ti⁴⁺ ion. With the increase of La₂O₃ and the decrease of Tm₂O₃, the dielectric constant of BaTiO₃ was enhanced in spite of the reduction of tetragonality. P-E hysteresis measurements revealed that this phenomenon was based on the improvement of remanent polarization with the increase of La₂O₃ concentration. The introduction of excess Tm₂O₃ in BaTiO₃ suppressed the grain growth and BaTiO₃ ceramics showed higher temperature stability due to the stable tetragonal structure and the small grain size with the increase of Tm₂O₃ concentration.     

The correlation between structure and magnetic properties in the manganites La0.7Ca0.3−xTexMnO3 (0≤x≤0.15)

The effect of Te-doping at La-site on structural, magnetic and transport properties in the manganites La_0.7Ca_0.3−xTe_xMnO₃ (0≤x≤0.15) has been investigated. All samples show an orthorhombic structure (O′-Pbnm) at room temperature. It shows that the Mn-O-Mn bond angle decreases and the Mn-O bond length increases with the increase in the Te content. All samples exhibit an insulator-metal (I-M) transition and the resistivity increases with the increase in the Te-doping level. Additionally, the Curie temperature T_c decreases and the transition becomes broader with increasing Te-doping level, in contrast, the magnetization of Te-doping samples at low temperatures decrease with increasing x as x≤0.10 and then increase with further increasing x to 0.15. The results are discussed in terms of Jahn-Teller (JT) vibrational anisotropy Q₃/Q₂ and the opening of the new DE channel between Mn²⁺-O-Mn³⁺ due to the introduction of Mn²⁺ ions because of the substitution of Te⁴⁺ ions for Ca²⁺ ions.     

Effect of Mn-site vacancies on the magnetic entropy change and the Curie temperature of La0.67Ca0.33Mn1−xO3 perovskite

Single-phase polycrystalline samples of La_0.67Ca_0.33Mn_1−xO₃ (x=0.00, 0.02, 0.04, 0.06) have been prepared using the sol-gel method. The structure, magnetocaloric properties and the Curie temperature of the samples with different Mn vacancy concentrations have been investigated. The experimental results show that vacancy doping at the Mn-sites has a significant influence on the magnetic properties of La_0.67Ca_0.33Mn_1−xO₃. The Curie temperature decreases monotonically with increasing the Mn-site vacancy concentration x. A remarkable enhancement of the magnetic entropy change has been obtained in the La_0.67Ca_0.33Mn_0.98O₃ sample. The entropy change reaches |ΔS_M|=3.10 J kg⁻¹ K⁻¹ at its Curie temperature (264 K) under an applied magnetic field H=10 kOe, which is almost the same value as that of pure Gd.     

Electrical and electrochemical properties of molten salt-synthesized Li4Ti5−xSnxO12 (x=0.0, 0.05 and 0.1) as anodes for Li-ion batteries

Submicron-sized polyhedral Li₄Ti_5−xSn_xO₁₂ (x=0.0, 0.05, and 0.1) materials were successfully prepared by a single-step molten salt method. The structural, morphological, transport and electrochemical properties of the Li₄Ti_5−xSn_xO₁₂ were studied. X-ray diffraction patterns showed the formation of a cubic structure with a lattice constant of 8.31 Å, and the addition of dopants follows Vegard's law. Furthermore, FT-IR spectra revealed symmetric stretching vibrations of octahedral groups of MO₆ lattice in Li₄Ti₅O₁₂. The formation of polyhedral submicron Li₄Ti_5−xSn_xO₁₂ particles was inferred from FE-SEM images, and a particle size reduction was observed for Sn-doped Li₄Ti₅O₁₂. The chemical composition of Ti, O and Sn was verified by EDAX. The DC electrical conductivity was found to increase with increasing temperature, and a maximum conductivity of 8.96×10⁻⁶ S cm⁻¹ was observed at 200 °C for Li₄Ti₅O₁₂. The galvanostatic charge–discharge behavior indicates that the Sn-doped Li₄Ti₅O₁₂ could be used as an anode for Li-ion batteries due to its enhanced electrochemical properties.     

Synthesis, structural and electrical properties of La and Nb modified Bi4Ti3O12 ferroelectric ceramics

Polycrystalline ceramic samples of Bi_4−xLa_xTi₃O₁₂ (x=0.0, 0.5 and 1) and Bi_3.5La_0.5Ti_3−yNb_yO₁₂ (y=0.02 and 0.04) have been synthesized by standard high temperature solid state reaction method using high purity oxides and carbonates. The effect of lanthanum doping on Bi-site and Nb doping on Ti-site on the structural and electrical properties of Bi₄Ti₃O₁₂ powders was investigated by X-ray diffraction, scanning electron microscopy, dc conductivity and dielectric studies. A better agreement between the observed and calculated X-ray diffraction pattern was obtained by performing the Rietveld refinement with a structural model using the non-centrosymmetric space group Fmmm in all the cases. A better agreement between observed and calculated d-values also shows that the lattice parameters calculated using the Rietveld refinement analysis are better. The increase in lanthanum and niobium contents does not lead to any secondary phases. It is found that La³⁺ doping reduces the material grain size and changes its morphology from the plate-like form to a spherical staking like form. The substitution of Nb for Ti ions affected the degree of disorder and modified the dielectric properties leading to more resistive ceramic compounds. The shape and size of the grains are strongly influenced by the addition of niobium to the system. The activation energies of all the compounds were calculated by measuring their dc electrical conductivities. The frequency and temperature dependent dielectric behavior of all the compounds have also been studied and the results are discussed in detail. The substitution of La and Nb on the Bi and Ti sites decreased the T_c and improved the dielectric and ferroelectric behavior.     

Ti deficiency effect on the dielectric response of CaCu3Ti4O12 ceramics

Single phase ceramics CaCu₃Ti_4.0O₁₂ and CaCu₃Ti_3.9O₁₂ have been prepared using the traditional solid-state reaction method. Compared with the stoichiometric ceramics CaCu₃Ti_4.0O₁₂, Ti-deficient ceramics CaCu₃Ti_3.9O₁₂ have the larger lattice parameter, the higher force constant, and smaller dielectric constant and the lower dissipation factor, although their fundamental characters of dielectric response are similar. Their characteristic relaxation frequencies are not well fitted with the Arrhenius Law but a tentatively supposed relation. With the Cole-Cole Law, the fitted broadened factors of dissipation peaks are 0.5433 and 0.8651 for CaCu₃Ti_3.9O₁₂ and CaCu₃Ti_4.0O₁₂, respectively. All facts mentioned above imply that mutually correlated motion of Ti ions or defects may be expected to be responsible for the giant dielectric constant and high dissipation factor of CaCu₃Ti_4.0O₁₂.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

Power factors of late rare earth-doped Ca3Co2O6 oxides

Polycrystalline samples of (Ca_1−xR_x)₃Co₂O₆ with R = Gd, Tb, Dy and Ho at x=0-0.1 were synthesized and the effects of rare earth substitution on their thermoelectric properties were investigated. In the high-temperature region, the rare earth substitution resulted in an increase in the Seebeck coefficients (S), and the S values increased with decreasing ionic radius of rare earth elements in the order Gd³⁺>Tb³⁺>Dy³⁺>Ho³⁺. In contrast, the influence of rare earth substitution on the electrical resistivity was small. The high-temperature power factor was thereby improved by the late rare earth substitutions, particularly those with Ho³⁺ for Ca²⁺. For the Ho-doped samples (x≤0.05), the power factor was significantly improved by increasing Ho concentration.