Electro-optical features of antiferroelectric liquid crystal material (S)-(+)-4-(1-methylheptyloxycarbonyl) phenyl 4′-(6-octanoyloxyhex-1-oxy) biphenyl-4-carboxylate in its ferro and antiferroelectric phases

A detailed investigation of the electro-optical switching parameters of an antiferroelectric liquid crystal (S)-(+)-4-(1-methylheptyloxycarbonyl) phenyl 4′-(6-octanoyloxyhex-1-oxy) biphenyl-4-carboxylate (abbreviated as S-7H6Bi) has been carried out. S-7H6Bi has paraelectric (SmA^?) and ferroelectric (SmC^?) phases in addition to antiferroelectric (SmC^?_A) phase. Switching parameters viz. spontaneous polarization and switching time were determined by polarization reversal method. The spontaneous polarization (P_s) is found to be highly temperature dependent and decreases with temperature. The maximum value of P_s is found to be ∼90 nC/cm² whereas the switching time (t_s) is found to be of the order 1-2 ms. The temperature dependent torsional viscosity (γ_t) is of the order 10 Pa sec. It increases with decrease in temperature.     

Dielectric, thermal and optical study of an unusually shaped liquid crystal

Dielectric measurements have been carried out for the determination of real and imaginary parts of the permittivity of a newly synthesized, unusually shaped liquid crystal. The sample has been investigated in the frequency range from 100 Hz to 10 MHz within a temperature range 80-130 °C. The dielectric measurements in the smectic A phase indicate a Cole-Cole type of dispersion, and the activation energy was found to be 5.5 meV by using the Arrhenius plot of relaxation time. In addition to this, thermal and optical transmittance studies have also been conducted in the above mentioned temperature range, and the temperature dependence of these parameters has been discussed in detail. The phase transition temperature obtained from a differential scanning calorimetry (DSC) study matches within 2 °C that was obtained from an optical transmittance study. The dielectric and optical behavior of the unusually shaped liquid crystal has been explained on the basis of a proposed theoretical model in which a sample possesses two different conformers having induced polarizations in opposite directions.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

Optical, thermal, dielectric and ferroelectric behaviour of sodium acid phthalate (SAP) single crystals

Sodium acid phthalate (SAP), an efficient semi-organic crystal having dimensions 17×8×2 mm³ has been grown from aqueous solution by slow evaporation technique at room temperature within the period of 2 weeks. The lattice parameters of the grown crystals were determined using single-crystal X-ray diffraction analysis. The presence of functional groups was estimated qualitatively by Fourier transform infrared (FTIR) analysis. The band gap energy was determined using optical absorption studies. The TG/DTA analysis reveals that the SAP crystal is thermally stable up to 141.6 °C. The dielectric constant and dielectric loss was studied as a function of frequency and the corresponding activation energy (E_a) has been calculated for the grown crystal. Scanning electron microscope studies enunciate the ferroelectric domain patterns of the SAP crystal. Ferroelectric property of the grown crystal was confirmed by hysteresis loop studies.     

Heats of solution/substitution and of fusion of Cs(1−x)KxCl compositions 0<x<0.57 by differential scanning calorimetry

Measurements of the change in heat (enthalpy) of solid-solid transition ΔH_t and of fusion ΔH_fus in crystalline CsCl effected by the presence of guest ion K⁺ up to 56.5 mol% using differential scanning calorimetry are reported. The range of K⁺ solubility is found to be higher and at variance with the subsolidus region described in earlier reports. Novel features of ΔH_t and ΔH_fus dependence on solute composition are in contrast to parallel binary systems, viz. CsNO₃-RbNO₃, CsNO₃-TlNO₃ and RbNO₃-TlNO₃. Some fundamental solution quantities are calculated from heat of transition, viz. slope ΔH_t/x or and χ-apparent partial molar heat of solution and partial molar heat of solution at infinite dilution, respectively.     

Molecular alloys as phase change materials (MAPCM) for energy storage and thermal protection at temperatures from 70 to 85 °C

Molecular alloys, that combine a relatively high heat of melting with a suitable melting temperature adapted to the application temperature, are excellent materials for thermal protection and for thermal energy storage. Of special interest is the fact that, by making alloys of molecular materials; the range of melting can be adjusted over a range of temperatures. The present paper reports on the design of MAPCMs to be used for energy storage and thermal protection at temperatures from 70 to 85 °C. The aim is to use these materials for thermal protection in the catering sector in order to avoid proliferation of micro organisms; the minimal temperature required is higher than 65 °C. The work illustrates how some fundamental studies are helpful in choosing the right composition that is able to work at the temperature required for an application. Several molecular alloys using the n-alkanes are elaborated and characterized. The preparation of mixed crystals, their crystallographic and thermodynamic properties and stability, phase change behaviour, and their use in practical applications are reported.     

Dielectric and AC ionic conductivity investigations in K3H(SeO4)2 single crystal

Optical observation under the polarizing microscope and DSC measurements on K₃H(SeO₄)₂ single crystal have been carried out in the temperature range 25-200 °C. It reveals a high-temperature structural phase transition at around 110 °C. The crystal system transformed from monoclinic to trigonal. Electrical impedance measurements of K₃H(SeO₄)₂ were performed as a function of both temperature and frequency. The electrical conduction and dielectric relaxation have been studied. The temperature dependence of electrical conductivity indicates that the sample crystal became a fast ionic conductor in the high-temperature phase. The frequency dependence of conductivity follows the Jonscher's universal dynamic law with the relation σ(ω)=σ(0)+Aωⁿ, where ω is the frequency of the AC field, and n is the exponent. The obtained n values decrease from 1.2 to 0.1 from the room temperature phase to fast ionic phase. The high ionic conductivity in the high-temperature phase is explained by the dynamical disordering of protons between the neighboring SeO₄ groups, which provide more vacant sites in the crystal.     

The nonlinear refraction and nonlinear absorption in 4-(4,6-diaminopyrimidin-2-ylthio) substituted double-decker Lu(III) phthalocyanine

A 4-(4,6-diaminopyrimidin-2-ylthio) substituted double-decker Lu(III) phthalocyanines (4) have been prepared and characterized by elemental analysis, IR, UV-vis and ¹H NMR spectroscopies. The nonlinear refractive index, nonlinear absorption and the optical limiting (OL) performance of the compound 4 in a 0.5 mm spectroscopic cell in DMF solution were investigated by using 4 ns pulse laser at 532 nm. Z-scan experiments have been conducted between 0.24 and 2.39 GW/cm² peak intensities for 10 Hz repetition rate and also between 2.39 and 23.89 GW/cm² peak intensities for 1 Hz repetition rate. The thermal effect contributes to the nonlinear response of the material higher than 0.72 GW/cm² peak intensity at 10 Hz. We measured the effective nonlinear refractive index of the material as 1.2×10⁻¹¹ esu at 3.5×10⁻⁴ M concentration with the peak intensity less than 0.72 GW/cm² and we found that nonlinear absorption was very small. On the other hand, when concentration is increased to 2.4×10⁻³ M material's nonlinear absorption becomes dominant mechanism for the nonlinear response and the compound 4 indicates OL behavior at 2.4×10⁻³ M concentration.     

Improved dielectric properties of (Pb,Ca)TiO3 thin films prepared by metal-organic decomposition method

(Pb,Ca)TiO₃ (PCT) thin films have been deposited on Pt/Ti/SiO₂/Si substrate by metal-organic decomposition (MOD) technique. The film processing parameters such as drying and annealing temperatures have been optimized to obtain good-quality PCT films. Compositional analysis of the film has been studied by X-ray photoelectron spectroscopy (XPS). The effect of the annealing temperature on the crystalline structure, microstructure and electrical properties have been investigated by X-ray diffraction, atomic force microscopy (AFM) and impedance analyzer, respectively. Amorphous PCT films form at 350 °C and crystallize in the perovskite phase following the isothermal annealing at ?650 °C for 3 h in oxygen ambient. Typical tetragonal structure of the PCT film is evidenced from X-ray diffraction pattern. The grain size in the PCT films increases with an increase in annealing temperature. Significant improvement in the dielectric constant value is observed as compared to other reported work on PCT films. The observed dielectric constant and dissipation factor at 100 kHz for 650 °C annealed PCT films are 308 and 0.015, respectively. The correlation of the film microstructural features and electrical behaviors is described.     

Metastable phases in Gallium-Indium eutectic alloy particles and their size dependence

In this paper, submicrometer-sized Ga-In eutectic alloy particles were dispersed into polymethylmethacrylate (PMMA) matrix by ultrasonic vibration and sedimentation method. The solidification and melting processes of Ga-In eutectic alloy particles were studied by differential scanning calorimeter (DSC). Four endothermal peaks with the onset temperature located at 16, −11, −22, and −27 °C were observed in DSC heating curves, which corresponded to the melting process of the stable Ga-In phase α-Ga(In) and three metastable phases of β-Ga(In), δ-Ga(In) and γ-Ga(In), respectively. The stable phase α-Ga(In) can only be formed when the size of alloy particle was larger than 0.58 μm. Conversely, metastable phases β-Ga(In), δ-Ga(In) and γ-Ga(In) are mainly formed. The result shows that phase structures in Ga-In eutectic alloy are size dependent.     

Sr2CeO4:Eu and Sr2CeO4:5 mol% Eu, 3 mol% Dy microphosphors: Wet chemistry synthesis from hybrid precursor and photoluminescence properties

In this article, Sr₂CeO₄:x mol% Eu³⁺ and Sr₂CeO₄:5 mol%Eu³⁺, 3 mol% Dy³⁺ phosphors were synthesized from assembling hybrid precursors by wet chemical method. As-prepared samples present uniform grain-like morphology and the particle size is about 0.2 μm. The luminescence spectra of Sr₂CeO₄:x mol% Eu³⁺ have been measured to examine the influence of the intensity of red emission lines for Eu³⁺ on the concentration of Eu³⁺, showing that the intensity of the red emission increases with an increase of the concentration from 1 to 5 mol%. Additionally, from the emission spectra of Sr₂CeO₄:5 mol%Eu³⁺, 3 mol% Dy³⁺ phosphors, the characteristic lines of Dy³⁺ have also been observed. This result indicates that there also exists an energy transfer process between Sr₂CeO₄ and Dy³⁺.     

An integral fitting method for analyzing the isochronal transformation kinetics: Application to the crystallization of a Ti-based amorphous alloy

An integral fitting method has been developed to determine the phase transformation mechanism and to extract the kinetic parameters during the crystallization of amorphous alloys. The proper kinetic function of the phase transformation was firstly deduced. Theoretical differential scanning calorimetry curves were then calculated. All the kinetic parameters can be extracted by fitting the calculated differential scanning calorimetry curves to experimental data. We applied the integral fitting method to analyze the isochronal crystallization of the Ti₅₀Cu₄₂Ni₈ amorphous alloy. Results indicate that a transformation process considering impingement is more suitable to describe the crystallization kinetics of this alloy than using the traditional Johnson-Mehl-Avrami model. Mean values of the obtained kinetic parameters show strong heating rate dependence.     

Nanoparticles of the giant dielectric material, CaCu3Ti4O12 from a precursor route

A method of preparing the nanoparticles of CaCu₃Ti₄O₁₂ (CCTO) with the crystallite size varying from 30 to 200 nm is optimized at a temperature as low as 680 °C from the exothermic thermal decomposition of an oxalate precursor, CaCu₃(TiO)₄(C₂O₄)₈·9H₂O. The phase singularity of the complex oxalate precursor is confirmed by the wet chemical analyses, X-ray diffraction, FT-IR and TGA/DTA analyses. The UV-vis reflectance and ESR spectra of CCTO powders indicate that the Cu(II) coordination changes from distorted octahedra to nearly flattened tetrahedra (squashed) to square-planar geometry with increasing annealing temperature. The HRTEM images have revealed that the evolution of the microstructure in nanoscale is related to the change in Cu(II) coordination around the surface regions for the chemically prepared powder specimens. The nearly flattened tetrahedral geometry prevails for CuO₄ in the near surface regions of the particles, whereas square-planar CuO₄ groups are dominant in the interior regions of the nanoparticles. The powders derived from the oxalate precursor have excellent sinterability, resulting in high-density ceramics which exhibited giant dielectric constants upto 40,000 (1 kHz) at 25 °C, accompanied by low dielectric loss <0.07.     

Specific heat measurements in pure and in (Cu, Mn, Fe, Ni)-doped single-crystals of l-arginine phosphate monohydrate

The influence of highly diluted impurities (Cu, Mn, Fe, Ni) on the temperature (T) dependence of the specific heat (c_p) of l-arginine phosphate monohydrate (LAP) was investigated in the temperature range 1.8-300 K. The doped samples yielded values for c_p in excess to those obtained for a pure LAP sample. The melting temperatures (T_m≈420 K) obtained by differential scanning calorimetry for pure and doped LAP samples were found not to be significantly affected by the impurities. The T-dependence of c_p was fully accounted for by taking into consideration the Debye contribution, an Einstein term and a contribution due to both Frenkel and Schottky defects. The model fit all c_p versus T data using a single value for both the Debye (θ_D=160 K) and the Einstein (T_E=376.8 K) temperatures, and for the energy (ε_d=157.9 meV) required to create the defects.     

Polystyrene-co-maleic acid/CdS nanocomposites: Preparation and properties

Composites of CdS nanoparticles confined in a polystyrene-co-maleic acid (PS-co-MAc) matrix have been prepared and characterized. It was shown that the acid groups of the co-polymer could be successfully used to control the aggregation of the nanoparticles, because they act as coordinate sites for Cd ions. UV-VIS measurements showed a blue shift of the absorption threshold, proving the presence of nanoparticles. An average size of the nanoparticles of about 4 nm is estimated from the change in band gap energy. Although the FTIR spectrum of the nanocomposite showed the presence of C-S bonds, a broad emission originating from surface recombination sites are noticed. DSC and TGA measurements revealed changes in thermal properties upon incorporation of nanoparticles. No thermal transition was observed in the nanocomposite, while the pure co-polymer exhibits a glass transition at 190 °C. In the presence of nanoparticles the onset of the thermal decomposition of the matrix is also shifted by 50 °C towards a higher temperature.     

Microwave dielectric properties of high quality factor La(Mg0.5−xCaxSn0.5)O3 ceramics

The microwave dielectric properties of La(Mg_0.5−xCa_xSn_0.5)O₃ ceramics were examined with a view to their exploitation for wireless communications. The La(Mg_0.5−xCa_xSn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The La(Mg_0.5−xCa_xSn_0.5)O₃ ceramics contained Ca₂SnO_4, CaSnO₃, and La₂O₃. The amount of Ca₂SnO₄ increased with increasing sintering temperature. However, the relative amount of CaSnO₃ decreased with increasing sintering temperature. An apparent density of 6.52 g/cm³, a dielectric constant (ε_r) of 20.2, a quality factor (Q×f) of 80,500 GHz, and a temperature coefficient of resonant frequency (τ_f) of −79 ppm/°C were obtained for La(Mg_0.4Ca_0.1Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h.     

Phase evolution and microwave dielectric properties of Bi3SbO7 ceramic

The Bi₃SbO₇ ceramic was prepared by the solid state reaction method and its phase evolution at different temperatures was studied. Low temperature phase α-Bi₃SbO₇ was formed at about 890 °C and it started to transform to high temperature phase β-Bi₃SbO₇ at about 960 °C. Microwave dielectric constants of α-Bi₃SbO₇ ceramic and β-Bi₃SbO₇ ceramic were 43.2 and 37.6, Qf value were 2080 and 5080 GHz, respectively. TCF of α-Bi₃SbO₇ ceramic was near zero and TCF of β-Bi₃SbO₇ ceramic was about −120 ppm/°C. The Bi₃SbO₇ ceramic is a promising candidate for low temperature co-fired ceramic (LTCC) technology due to its large dielectric constant, low dielectric loss at microwave region, low sintering temperature and simple composition.