Jump rate and linear distance of vacancy on the structure and electrical conductivity of Ni0.65Zn0.35CuxFe2−xO4 ferrites

Ferrite compositions of Ni_0.65Zn_0.35Cu_xFe_2−xO₄ (0⩽x<1) were examined using X-ray analysis. The effect of the linear distance of vacancy jumping on the lattice parameter was studied. The jump rate of vacancy increased with increasing Cu concentration. The increase of jump rate of vacancy enhanced the linear distance which increased the conductivity and mobility of the charge carriers. The majority of charge carriers of our systems are holes. The estimated linear distance of each jump was 2.86×10⁻⁷ m. The decrease of thermal conductivity was attributed to the increase of the jump rate and also the linear distance. The formation of oxygen vacancies during the substitution of Cu²⁺ ions for Fe³⁺ ions helped the internal stress to decrease the lattice parameter. Because the ionic radius of O²⁻ (0.136 nm) is larger than that of Fe³⁺ (0.067 nm) ion.     

Al3+掺杂的CuZn铁氧体的结构，电学和磁学特性

采用固相合成反应技术制备纳米Cu_0.5Zn_0.5Fe_2-xAl_xO₂(x=0.0,0.1,0.2,0.3,0.4和0.5)铁氧体材料,研究Al³⁺含量对结构,电学和磁学性质的影响. 采用X射线衍射研究单相立方尖晶石结构. 利用Scherrer公式估算晶粒尺寸. 测定了温度依赖的直流电阻率.结果表明随Al³⁺含量的增加,晶格常数减小,孔隙度增加,饱和磁化强度值降低,Al³⁺对铁氧体的介电常数、介电损耗角的正切值和介质损耗因子等介电性能有明显影响,这可能与空间电荷极化有关.     

Remarkable influence on the dielectric and magnetic properties of lithium ferrite by Ti and Zn substitution

The effect of Zn and Ti substitution on the magnetic and electrical properties of Li_0.5Zn_xTi_xMn_0.05Fe_2.45−2xO₄ ferrites (x=0.0 to 0.30 in steps of 0.05) +0.5wt% Bi₂O₃ prepared by a standard ceramic technique has been investigated. Electrical conductivity and dielectric measurements at different temperatures from 300 K to 700 K in the frequency range from 100 Hz to 2 MHz have been analysed. The variation of the real part of dielectric constant (ε^′) and loss tangent (tanδ) with frequency and temperature has been studied; it follows the Maxwell–Wagner model based on the interfacial polarization in consonance with the Koops phenomenological theory. It is found that the permittivity of zinc and titanium substituted lithium ferrite improves and shows a maximum value ( 1.5×10⁵) at 100 Hz for the x=0.25 sample. The dielectric transition temperature (T_d) depends on the concentration of Ti and Zn in Li_0.5Zn_xTi_xMn_0.05Fe_2.45−2xO₄. The saturation magnetization and Curie temperature both decrease with increase in the concentration of Ti and Zn in the ferrite.     

Defect structure and dielectric properties of Bi-based pyrochlores probed by positron annihilation

Positron annihilation lifetime (PAL) and Doppler broadening (DB) techniques have been performed to identify structural defects of the bismuth based pyrochlore systems with generic formula (Bi_1.5Zn_0.5)(Zn_0.5−x/3Ti_xNb_1.5−2x/3)O₇ (x = 0, 0.25, 0.5,1.0, 1.5). We found that all studied compounds contain substantial amount of the lattice vacancy defects, the variation of the annihilation lifetime suggests that the defects structure undergoes significant changes. The complex defects could be produced with increasing content of Ti, resulting in a drop in the intensity I₂ in the Ti-rich sample. At 1 MHz their dielectric constant (?′) varies from 150 for Ti-poor system to 210 for Ti-rich system and loss tangent (tan δ) remains rather low level. The high dielectric constant response of the BZTN ceramics is attributed to loosening state of cations located in the center of octahedral, so favor off-center displacement. The occurrence of complex defects help to enhance the dielectric constant.     

Effects of Fe2+ and Zn2+ substitution on the structure and high-pressure stability of MgAl2O4 spinel from DFT calculations

Using density functional theory we show the effects of transition (Fe²⁺) and non-transition (Zn²⁺) divalent cationic substitutions on the following structural parameters: lattice parameters, bond lengths and polyhedral volumes under varying hydrostatic pressures. Fe²⁺ and Zn²⁺ substitutions lead to contrasting modifications of tetrahedral Mg–O bond lengths. Fe²⁺ (50%)increase the tetrahedral Mg–O bond lengths by 0.21%, whereas Zn²⁺ (50%) reduce it by 0.06%.We present the equations of state of Mg spinel with 50% Fe and Zn substitutions as a function of pressure. This study presents the decomposition pressure (P_T) of spinel to periclase (MgO) and corundum (α-Al₂O₃) as a function of Fe and Zn concentrations (x). For pure spinel, P_T=12.1 GPa. Fe²⁺substitution lowers P_T linearly with its concentration as P_T=?12.56x+12.02. But, Zn²⁺ increases P_T non-linearly along a quadratic relation: P_T=42.057x²+14.171x+12.174. We calculated the C₄₄ elastic constant to explain the contrasting effects of Fe and Zn on the decomposition pressure of spinel phase.     

Dielectric behavior of spin-deposited nanocrystalline nickel-zinc ferrite thin films processed by citrate-route

Nanocrystalline nickel-zinc ferrite thin films with the general formula Ni_1−xZn_xFe₂O₄, where x=0.0, 0.2, 0.4 and 0.6 were fabricated via a chemical route known as the citrate precursor route. These films were spin-deposited on indium-tin oxide coated glass, fused quartz and amorphous Si-wafer substrates, and annealed at various temperatures up to 650 °C. The films annealed below 400 °C were found to be X-ray amorphous, while the films annealed at and above 400 °C were polycrystalline exhibiting a single-phase spinel structure. The average grain size of the films evaluated by transmission electron microscopy, is found to be in the range 4-8.5 nm. The room temperature DC resistivity of the films is in the range 10³-10⁷ Ω m. Dielectric constant and dielectric loss were measured in the frequency range 100 Hz-1 MHz. Dielectric constant of the films is found to lie between 25 and 44, while the loss factor is if the order of 10⁻². The higher values of the dielectric constant for films having higher zinc concentration are attributable to the enhanced hopping between Fe²⁺ and Fe³⁺ ions in these samples. The M-H hysteresis measurement of the nickel ferrite thin films annealed at 650 °C showed narrow hysteresis loop—a characteristic of soft ferromagnetic material.     

Infrared and structural studies of Mg1-xZnxFe2O4 ferrites

Compositions of polycrystalline Mg-Zn mixed ferrites with the general formula Mg_1−xZn_xFe₂O₄ (0≤x≤1) were prepared by the standard double sintering ceramic method. The structural properties of these ferrites have been investigated using X-ray diffraction and infrared absorption spectroscopy. The lattice parameter, particle size, bonds length, force constants, density, porosity, shrinkage and cation distribution of these samples have been estimated and compared with those predicted theoretically. Most of these values were found to increase with increasing Zn content. The energy dispersive (EDS) analysis confirmed the proposed sample composition. The scanning electron microscope (SEM) and transmission electron microscope (TEM) micrographs showed aggregates of stacked crystallites of about 200-800 nm in diameter. Far infrared absorption spectra showed two significant absorption bands. The wave number of the first band, ν₁, decreases with increasing Zn content, while the band, ν₂ shifts linearly towards higher wave numbers with Zn contents, over the whole composition range. The room temperature electrical resistivity was found to decrease as Zn-content increases. Values of the vacancy model parameters showed that the packing factors P_a and P_b decrease, the fulfillment coefficient, α, remains almost constant and the vacancy parameter, β, strongly increases with increasing Zn content in the sample. The small values of P_a, P_b, α and the strong increase of the vacancy parameter, β, indicate the presence of cation or anion vacancies and the partial participation of the Zn²⁺ vacancies in the improvement of the electrical conductivity in the Mg-Zn ferrites.     

Effect of Cd on the structural, magnetic and electrical properties of nanostructured Mn-Zn ferrite

Nanoparticles of Mn_0.5Zn_0.5−xCd_xFe₂O₄ (x=0.0, 0.1, 0.2 and 0.3) have been synthesized by a chemical co-precipitation method. The lattice constant increases with increasing Cd content. X-ray calculations indicate that there is deviation in the cation distribution in the nanostructured spinel ferrite. The dielectric constant and dielectric loss decrease for the samples with Cd content up to x=0.2. However the dielectric constant rises for x=0.3. This is due to an increase in the hopping process at the octahedral (B sites). The dielectric constant increases with increase in temperature, indicating a thermally activated hopping process. The DC resistivity increases with Cd content up to x=0.2 and decreases for Cd content x=0.3. The maximum magnetization of all the samples decreases with increase in Cd content.     

Structural and electrical properties of nanometric Ni-Cu ferrites synthesized by citrate precursor method

Nanometric nickel copper ferrites Ni_1−xCu_xFe₂O₄, 0≤x≤0.45 were prepared by the citrate precursor method. X-ray diffraction measurements confirm the formation of single phase cubic spinel structure. The lattice parameter (a) is increased with increasing Cu²⁺ ion substitution. The crystallite size was calculated from XRD data and compared with that obtained from TEM micrographs. A significant increase in the density is observed with increasing Cu content. The IR absorption spectra were used for the detection and confirmation of the chemical bonds in spinel ferrites. The dielectric constant ε′ and dielectric loss showed a decrease with increasing frequency for all samples. The decrease in the ac conductivity was ascribed to the increase in hopping length.     

Effect of Y2O3 doping on the electrical transport properties of Sr2MnNiFe12O22 Y-type hexaferrite

Y₂O₃ doped Y-type composite hexa-ferrites Sr₂MnNiFe₁₂O₂₂ + xY₂O₃ (x = 0 wt%, 1 wt%, 2 wt%, 3 wt%, 4 wt%, 5 wt%) were synthesized successfully using sol-gel auto combustion technique. X-ray diffraction analysis reveals Y-type hexagonal structure with few traces of secondary phases. The decrease in grain size as a function of Yttrium content is attributed to the fact that Yttrium acts as a grain inhibitor. The DC resistivity was observed to increase with increasing Yttrium-contents due to the unavailability of Fe³⁺ ions at octahedral sites. Activation energy showed that the samples with high resistivity have high value of activation energy and vice versa. Permittivity decreases with the increase of frequency following Maxwell Wagner Model. In addition, the doped samples exhibit very low dielectric constant and low loss tangent in frequency range 20 Hz–1 MHz. The sample x = 5 wt% exhibit the lowest value of dielectric constant. The variation in imaginary part of dielectric constant and loss tangent with frequency show normal dielectric behavior for all the samples. The frequency dependent ac conductivity increases with increase in frequency and decrease with Y₂O₃ doping. These characteristics may be suitable for their potential applications in electromagnetic attenuation materials and microwave devices. The conductivity mechanism so determined was hopping mechanism. The dc resistivity of the doped ferrites measured in our case is about 10¹⁰ Ω-cm that meets the requirement for fabrication of components by electroplating.     

Effect of Sm,Co codoping on the dielectric and magnetoelectric properties of BiFeO3 polycrystalline ceramics

Multiferroic Bi_0.95Sm_0.05Fe_1−xCo_xO₃ (x=0−0.1) ceramics were prepared by the rapid liquid phase sintering method. For all the samples studied, the dielectric constant and dielectric loss decrease with increasing frequency in the range from 1 kHz to 1 MHz. It shows that the dielectric constant of Bi_0.95Sm_0.05FeO₃ at 10 kHz is about forty times larger than that of pure BiFeO₃. This dramatic change in the dielectric properties of Bi_0.95Sm_0.05Fe_1−xCo_xO₃ (x=0−0.1) samples can be understood in terms of the space charge limited conduction associated with crystal defects, which was indicated by the increase of magnetoelectric effect with doping Co³⁺ under applied magnetic field from 1 to 8 kOe. It was believed that the ferroelectric polarization enhancement comes from the exchange interaction between the Sm³⁺ and Fe³⁺ or Co³⁺ ions for Bi_0.95Sm_0.05Fe_0.95Co_0.05O₃ at room temperature.     

Influence of frequency, temperature and composition on electrical properties of polycrystalline Co0.5CdxFe2.5−xO4 ferrites

Polycrystalline ferrites with general formula Co_0.5Cd_xFe_2.5−xO₄ (0.0?x?0.5) were prepared by sol-gel method. The dielectric properties ε′, ε″, loss tangent tan δ and ac conductivity σ_ac have been studied as a function of frequency, temperature and composition. The experimental results indicate that ε′, ε″, tan δ and σ_ac decrease as the frequency increases; whereas they increase as the temperature increases. These parameters are found to increase by increasing the concentration of Cd content up to x=0.2, after which they start to decrease with further increase in concentration of Cd ion. The dielectric properties and ac conductivity in studied samples have been explained on the basis of space charge polarization according to Maxwell and Wagner's two-layer model and the hoping between adjacent Fe²⁺ and Fe³⁺ as well as the hole hopping between Co³⁺and Co²⁺ ions at B-sites. The values of activation energies E_f for conduction process are determined from Arrhenius plots, and the variations in these activation energies as a function of Cd content are discussed. The complex impedance analysis is used to separate the grain and grain boundary of the system Co_0.5Cd_xFe_2.5−xO₄. The variations of both grain boundary and grain resistances with temperature and composition are evaluated in the frequency range 42 Hz-5 MHz.     

Finite size effect and influence of temperature on electrical properties of nanocrystalline Ni–Cd ferrites

Electrical conductivity and dielectric measurements have been investigated for four different average grain sizes ranging from 3 to 7 nm of nanocrystalline Ni_0.2Cd_0.3Fe_2.5−xAl_xO₄ (0.0 ⩽ x ⩽ 0.5) ferrites. The impedance spectroscopy technique has been used to study the effect of grain and grain boundary on the electrical properties of the Al doped Ni–Cd ferrites. The analysis of data shows only one semi-circle corresponding to the grain boundary volume suggesting that the conduction mechanism takes place predominantly through grain boundary volume in the studied samples. The variation of impedance properties with temperature and composition has been studied in the frequency range of 120 Hz–5 MHz between the temperatures 300–473 K. The hopping of electrons between Fe³⁺ and Fe²⁺ as well as hole hopping between Ni³⁺ and Ni²⁺ ions at octahedral sites are found to be responsible for conduction mechanism. The dielectric constant and loss tangent (tan δ) are found to decrease with increasing frequency, whereas they increase with increasing temperature. The dielectric constant shows an anomalous behavior at selected frequencies, while the temperature increases, which is expected due to the generation of more electrons and holes as the temperature increases. The behavior has been explained in the light of Rezlescu model.     

Effect of Zn and Mg doping on structural,dielectric and magnetic properties of tetragonal CuFe2O4

The Cu_1?xA_xFe₂O₄ (A = Zn, Mg; x = 0.0, 0.5) ferrites were successfully synthesized by chemical co-precipitation method. X-ray diffraction and Raman spectroscopy reveals that all the ferrite samples are in single-phase with tetragonal structure for CFO and cubic spinel structure for CZFO and CMFO samples. SEM micrograph shows the variation of grain size with Zn and Mg doping in parent CFO sample. Frequency dependent dielectric response confirms the dielectric polarization and electrical conduction mechanism in the present series with a maximum value of dielectric constant and loss tangent for CZFO sample. The anomaly ～493 K in temperature dependent dielectric constant and dielectric loss is assigned to tetragonal to cubic phase transition in CFO sample. The magnetic measurement explored that the saturation value (M_s) is maximum for CZFO as compared to CFO and CMFO ferrites samples.     

A comparative study of different concentrations of pure Zn powder effects on synthesis,structure, magnetic and microwave-absorbing properties in mechanically-alloyed Ni–Zn ferrite

In this study, a powder mixture of Zn, Fe₂O₃ and NiO was used to produce different compositions of Ni_1−xZn_xFe₂O₄ (x=0.36, 0.5 and 0.64) nanopowders. High-energy ball milling with a subsequent heat treatment method was carried out. The XRD results indicated that for the content of Zn, x=0.64 a single phase of Ni–Zn ferrite was produced after 30 h milling while for the contents of Zn, x=0.36 and 0.5, the desired ferrite was formed after sintering the 30 h-milled powders at 500 °C. The average crystallite size decreased with increase in the Zn content. A DC electrical resistivity of the Ni–Zn ferrite, however, decreased with increase in the Zn content, its value was much higher than those samples prepared by the conventional ceramic route by using ZnO instead of Zn. This is attributed to smaller grains size which were obtained by using Zn. The FT-IR results suggested two absorption bands for octahedral and tetrahedral sites in the range of 350–700 cm⁻¹. The VSM results revealed that by increasing the Zn content from 0.36 to 0.5, a saturation magnetization reached its maximum value; afterwards, a decrease was observed for Zn with x=0.64. Finally, magnetic permeability and dielectric permittivity were studied by using vector network analyzer to explore microwave-absorbing properties in X-band frequency. The minimum reflection loss value obtained for Ni_0.5Zn_0.5Fe₂O₄ samples, about −34 dB at 9.7 GHz, making them the best candidates for high frequency applications.     

Study of dielectric and ac impedance properties of Ti doped Mn ferrites

We have reported dielectric and ac impedance properties of Ti doped Mn_1+xFe_2−2xO₄ (0x0.5) ferrites prepared by solid-state reaction method, using dielectric and impedance spectroscopy in the frequency range of 42 Hz–5 MHz, between the temperatures (300K–473K). The dielectric constant and dielectric loss (tan δ) decreases with increasing frequency but these parameters increase with increasing temperature. The dielectric loss tangent curves exhibit dielectric relaxation peaks at high frequencies (3.6 kHz–5 MHz), which are attributed to the coincidence of the frequency of charge hopping between the localized charge states and the external field. The dielectric properties have been explained on the basis of space charge polarization according to Maxwell–Wagner’s two-layer model and the hopping of charge between Fe²⁺ and Fe³⁺ as well as between Mn³⁺ and Mn²⁺ ions at B-sites. The complex impedance analysis has been used to separate grain and grain boundary in studied samples. Two semicircles corresponding to grain and grain boundary have been observed at low temperature, while only one semicircle has been seen at high temperatures. The resistance of grain and grain boundary both increase with Ti⁴⁺ doping.     

Magnetic studies of Li-Zn ferrites prepared by citrate precursor method

Ferrites having the general formula Li_0.5−0.5xZn_xFe_2.5−0.5xO₄ where 0≤x≤0.6 in steps of 0.2 were prepared by the citrate precursor method. The Curie temperature measured shows a decrease with increasing Zn concentration. Experimental results show that the room temperature initial permeability increases with the increase in the concentration of zinc. The initial permeability has also been studied as a function of frequency in the range of 100 Hz-1 MHz. The real part of initial permeability referred as initial permeability and the imaginary part of initial permeability better known as permeability loss show dispersion with frequency. Possible mechanism contributing to the above processes is discussed.     

Effect of Pr doping on magnetic and dielectric properties of Ni-Zn ferrites by “one-step synthesis”

Pr³⁺-doped Ni-Zn ferrites with a nominal composition of Ni_0.5Zn_0.5Pr_xFe_2−xO₄ (where x=0-0.08) were prepared by a one-step synthesis. The magnetic and dielectric properties of the as-prepared Ni-Zn ferrites were investigated. X-ray diffraction data indicated that, after doping, all samples consisted of the main spinel phase in combination of a small amount of a foreign PrFeO₃ phase. The lattice constants of the ferrites initially increased after Pr³⁺ doping, but then became smaller with additional Pr³⁺ doping. The addition of Pr³⁺ resulted in a reduction of grain size and an increase of density and densification of the as-prepared samples. Magnetic measurement revealed that the saturation magnetization of the as-prepared ferrites, M_s, decreased, while the coercivity, H_c, increased with increasing substitution level, x, and the Curie temperature, T_c, kept a rather high value, fluctuating between 308 and 320 °C. Both the real and imaginary parts of permeability of the ferrites decreased slightly after Pr³⁺ doping. However, the natural resonance frequency shifted towards higher frequency from 13.07 to 36.17 MHz after the addition of Pr³⁺, driving the magnetic permeability to much higher frequency, reaching the highest value (36.17 MHz) when x=0.04. Introduction of Pr³⁺ ions into the Ni-Zn ferrite reduced the values of the dielectric loss tangent, especially in the frequency range of 1-400 MHz. However, the magnitude of dielectric loss of the samples doped with different amounts of Pr³⁺ raised little.     

Sol–gel auto-combustion synthesis,structural and enhanced magnetic properties of Ni substituted nanocrystalline Mg–Zn spinel ferrite

Nanocrystalline arrays of Ni²⁺ substituted Mg–Zn spinel ferrite having a generic formula Mg_0.7−xNi_xZn_0.3Fe₂O₄ (x=0.0, 0.2, 0.4 and 0.6) were successfully synthesized by sol–gel auto-combustion technique. The fuel used in the synthesis process was citric acid and the metal nitrate-to-citric acid ratio was taken as 1:3. The phase, crystal structure and morphology of Mg–Ni–Zn ferrites were investigated by X-ray diffraction, scanning electron microscopy, and Fourier transformer infrared spectroscopy techniques. The lattice constant, crystallite size, porosity and cation distribution were determined from the X-ray diffraction data method. The FTIR spectroscopy is used to deduce the structural investigation and redistribution of cations between octahedral and tetrahedral sites of Mg–Ni–Zn spinel structured material. Morphological investigation suggests the formation of grain growth as the Ni²⁺ content x increases. The saturation magnetization and magneton number were determined from hysteresis loop technique. The saturation magnetization increases with increasing Ni²⁺ concentration ‘x’ in Mg–Zn ferrite.     

Effect of Nd substitution on structural and electrical properties of nanocrystalline zinc ferrite

Polycrystalline soft ferrite samples with general formula ZnNd_xFe_2−xO₄ (where x=0, 0.01, 0.02 and 0.03) were synthesized by oxalate co-precipitation method. The samples were characterized by XRD and SEM techniques. The single phase cubic spinel structure of all the samples was confirmed by XRD. The lattice constant and grain size of the samples are found to decrease with increase in Nd³⁺ content. Room temperature DC resistivity of the Nd³⁺ substituted zinc ferrites is 10² times higher than that of zinc ferrite. The dielectric constant (ε′) and dielectric loss (tan δ) of all the samples were measured in the frequency range 20 Hz-1 MHz. The dielectric behaviour is attributed to the Maxwell-Wagner type interfacial polarization. The dielectric loss of the samples is found to decrease with increase in Nd³⁺ content. High resistivity and low dielectric loss makes these ferrites particularly suitable for high frequency applications.