Structural and electrochemical properties of Nd-doped LiFePO4/C prepared without using inert gas

To further improve the electrochemical performance of LiFePO₄/C, Nd doping has been adopted for cathode material of the lithium ion batteries. The Nd-doped LiFePO₄/C cathode was synthesized by a novel solid-state reaction method at 750 °C without using inert gas. The Li_0.99Nd_0.01FePO₄/C composite has been systematically characterized by X-ray diffraction, EDS, SEM, TEM, charge/discharge test, electrochemical impedance spectroscopy and cyclic stability. The results indicate that the prepared sample has olivine structure and the Nd³⁺ and carbon modification do not affect the structure of the sample but improve its kinetics in terms of discharge capacity and rate capability. The Li_0.99Nd_0.01FePO₄/C powder exhibited a specific initial discharge capacity of about 161 mAh g^− 1 at 0.1 C rate, as compared to 143 mAh g^− 1 of LiFePO₄/C. At a high rate of 2 C, the discharge capacity of Li_0.99Nd_0.01FePO₄/C still attained to 115 mAh g^− 1 at the end of 20 cycles. EIS results indicate that the charge transfer resistance of LiFePO₄/C decreases greatly after Nd doping.     

Stable cycle-life properties of Ti-doped LiFePO4 compounds synthesized by co-precipitation and normal temperature reduction method

Submicron-sized LiFePO₄ and Ti-doped LiFePO₄ cathode materials were synthesized by a reformative co-precipitation and normal temperature reduction method, for which Ti ions were added in the process of preparing precursors to pursue a kind of sufficient and homogenous doping way. ICP and XRD analyses indicate that Ti ions were sufficiently doped in LiFePO₄ and did not alter its crystal structure. It is noted that higher Ti ions doping levels are conducive to electrochemical performance of LiFePO₄, especially on the aspect of stable cycle-life at higher C rates. The sample doped with 3 at% Ti shows the most impressive cycling performance, even after 100 cycles, discharge capacity of 133 mAh g⁻¹ was obtained (102.3% of its initial value) at 1C rate, and the discharge decreased little from 124 to 120 mAh g⁻¹ (96.8% of its initial value) at 2C rate.     

Silver-coated LiVPO4F composite with improved electrochemical performance as cathode material for lithium-ion batteries

Nano-structured LiVPO₄F/Ag composite cathode material has been successfully synthesized via a sol–gel route. The structural and physical properties, as well as the electrochemical performance of the material are compared with those of the pristine LiVPO₄F. X-ray diffraction (XRD) and scanning electron microscopy (SEM) reveal that Ag particles are uniformly dispersed on the surface of LiVPO₄F without destroying the crystal structure of the bulk material. An analysis of the electrochemical measurements show that the Ag-modified LiVPO₄F material exhibits high discharge capacity, good cycle performance (108.5 mAh g⁻¹ after 50th cycles at 0.1 C, 93% of initial discharge capacity) and excellent rate behavior (81.8 mAh g⁻¹ for initial discharge capacity at 5 C). The electrochemical impedance spectroscopy (EIS) results reveal that the adding of Ag decreases the charge-transfer resistance (R_ct) of LiVPO₄F cathode. This study demonstrates that Ag-coating is a promising way to improve the electrochemical performance of the pristine LiVPO₄F for lithium-ion batteries cathode material.     

Facile synthesis of Nb2O5 nanorod array films and their electrochemical properties

Nb₂O₅ nanorod array films were synthesized by a facile hydrothermal process using niobium metal foil and NH₄F as precursors. The Nb₂O₅ nanorods stand on the niobium metal foil substrate and are less than 100 nm in diameter and about 1 μm in length. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) characterizations indicate that these nanorods have orthorhombic structure and grew longitudinally along 〈0 0 1〉 direction. The nanorod growth mechanism was discussed. Thermal annealing at a temperature below 500 °C did not change the microstructure of nanorods but improve the crystallinity. The Nb₂O₅ nanorod array films have been tested as cathode material for lithium battery, which showed a good specific capacity up to 380 mAh g⁻¹ even after 50 charge/discharge cycles.     

Synthesis and electrochemical properties of nanostructured Li2FeSiO4/C cathode material for Li-ion batteries

Nanostructured Li₂FeSiO₄/C was synthesized by high-energy ball-milling and the amorphous citrate-assisted techniques. Similar redox behaviour is observed for samples prepared by the amorphous citrate-assisted route followed by a 4 h heat treatment: 0.3 V polarization and more sloping behaviour was observed when cycling between 2.0 V and 3.7 V at 60 °C; lower capacity fade is also observed compared to Li₂FeSiO₄/C prepared by the solid-state reaction technique. A discharge capacity of 102 mA h g^− 1 is obtained for samples prepared by the high-energy ball-milling method, while capacities decrease from 95 to 77 mA h g^− 1 using the amorphous citrate method for heat-treatment times increasing successively from 4 h to 18 h.     

Preparation, structure and oxide ion conductivity in Ce6−xYxMoO15−δ (x=0.1-1.4) solid solutions

The Ce_6−xY_xMoO_15−δ solid solution with fluorite-related structure have been characterized by differential thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), IR, Raman, scanning electric microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) methods. The electric conductivity of samples is investigated by Ac impedance spectroscopy. An essentially pure oxide-ion conductivity of the oxygen-deficiency was observed in pure argon, oxygen and air. The highest oxygen-ion conductivity was found in Ce_5.5Y_0.5MoO_15−δ ranging from 5.9×10⁻⁵ (S cm⁻¹) at 300 °C to 1.3×10⁻² (S cm⁻¹) at 650 °C, respectively. The oxide-ion conductivities remained stable over 80 h-long test at 800 °C. These properties suggested that significant oxide-ionic conductivity exists in these materials at moderately elevated temperatures.     

Porous LiNi0.75Co0.25O2 microspheres prepared via a hydrothermal process as cathode material for lithium ion batteries

Porous LiNi_0.75Co_0.25O₂ microspheres are successfully prepared by a simple hydrothermal process by using H[Ni_0.75Co_0.25OOH]₃ and LiOH as starting materials in the presence of urea for the first time. The synthesized samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), specific surface area (S_BET), and electrochemical performance. The synthesized LiNi_0.75Co_0.25O₂ has a good electrochemical performance with an initial discharge capacity of 169.3 mA g⁻¹ and good capacity retention of 96.7% after 50 cycles at 0.2 C (25 mA g⁻¹). The electrochemical lithium ion insertion/extraction process is quite reversible even at 5 C. Furthermore, the structure in the charge-discharge process is stable and the impedance increased slowly during cycling.     

Highly active Ce1−xCuxO2 nanocomposite catalysts for the low temperature oxidation of CO

A series of Ce_1−xCu_xO₂ nanocomposite catalysts with various copper contents were synthesized by a simple hydrothermal method at low temperature without any surfactants, using mixed solutions of Cu(II) and Ce(III) nitrates as metal sources. These bimetal oxide nanocomposites were characterized by means of XRD, TEM, HRTEM, EDS, N₂ adsorption, H₂-TPR and XPS. The influence of Cu loading (5-25 mol%) and calcination temperature on the surface area, particle size and catalytic behavior of the nanocomposites have been discussed. The catalytic activity of Ce_1−xCu_xO₂ nanocomposites was investigated using the test of CO oxidation reaction. The optimized performance was achieved for the Ce_0.80Cu_0.20O₂ nanocomposite catalyst, which exhibited superior reaction rate of 11.2 × 10⁻⁴ mmol g⁻¹ s⁻¹ and high turnover frequency of 7.53 × 10⁻² s⁻¹ (1% CO balanced with air at a rate of 40 mL min⁻¹, at 90 °C). No obvious deactivation was observed after six times of catalytic reactions for Ce_0.80Cu_0.20O₂ nanocomposite catalyst.     

Molten salt synthesis of Li1 + x (Ni0.5Mn0.5)1 − xO2 as cathode material for Li-ion batteries

Li_1 + x(Ni_0.5Mn_0.5)_1 − xO₂ cathode material for Li-ion batteries has been prepared by a molten salt method using Li₂CO₃ salt. The influences of synthetic temperature and time have been intensively investigated. It is easy to obtain materials with a hexagonal α-NaFeO₂ structure except broad peaks between 20° and 25°. Nickel in Li_1 + x(Ni_0.5Mn_0.5)_1 − xO₂ is oxidized to a trivalent state while manganese maintained a tetravalent state. It is found that the discharge capacities of all samples increase with cycling. The sample prepared at 850 °C for 5 h has a discharge capacity of 130 mAh g^− 1 between 2.5 and 4.5 V versus V_Li+/Li at a specific current of 0.13 mA cm^− 2 after 50 cycles at 25 °C.     

Advanced electrochemical performance of LiMn1.4Cr0.2Ni0.4O4 as 5 V cathode material by citric-acid-assisted method

Spinel LiMn₂O₄ and LiMn_1.4Cr_0.2Ni_0.4O₄ cathode materials were successfully synthesized by the citric-acid-assisted sol-gel method with ultrasonic irradiation stirring. The structure and electrochemical performance of the as-prepared powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometer, cyclic voltamogram (CV) and the galvanostatic charge-discharge test in detail. XRD shows that all the samples have high phase purity, and the powders are well crystallized. SEM exhibits that LiMn_1.4Cr_0.2Ni_0.4O₄ has more uniform cubic-structure morphology than that of LiMn₂O₄. EDX reveals that a small amount of Mn³⁺ still exists in LiMn_1.4Cr_0.2Ni_0.4O₄. The galvanostatic charge-discharge test indicates that the initial discharge capacities for the LiMn_1.4Cr_0.2Ni_0.4O₄ and LiMn₂O₄ at 0.15 C discharge rates are 130.8 and 130.2 mAh g⁻¹, respectively. After 50 cycles, their capacity are 94.1% and 85.1%, respectively. The CV curve implies that Ni and Cr dual substitutions are beneficial to the reversible intercalation and deintercalation of Li⁺, and suppress Mn³⁺ generation at high temperatures and provide improved structural stability.     

Study of a novel porous gel polymer electrolyte based on TPU/PVdF by electrospinning technique

Investigation on a new electrospun gel polymer electrolyte consisting of thermoplastic polyurethane (TPU) and poly(vinylidene fluoride) (PVdF) has been made. Its characteristics were investigated by scanning electron microscopy, FT-IR, Differential Scanning Calorimeter (DSC) analysis. This kind of gel polymer electrolyte had a high ionic conductivity about 3.2 × 10^− 3 S cm^− 1 at room temperature, and exhibited a high electrochemical stability up to 5.0 V versus Li⁺/Li, good mechanical strength and stability to allow safe operation in rechargeable lithium-ion polymer batteries. A Li/GPE/LiFePO₄ cell delivered a high discharge capacity when it was evaluated at 0.1 °C—rate at 25 °C (167.8 mAh g^− 1). And a very stable cycle performance also existed under this low current density.     

Characterization of single-crystalline In2O3 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

Epitaxial In₂O₃ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates by metalorganic chemical vapor deposition (MOCVD). The films were deposited at different substrate temperatures (450-750 °C). The film deposited at 650 °C has the best crystalline quality, and observation of the interface area shows a clear cube-on-cube epitaxial relationship of In₂O₃(1 0 0)||YSZ(1 0 0) with In₂O₃[0 0 1]||YSZ[0 0 1]. The Hall mobility of the single-crystalline In₂O₃ film deposited at 650 °C is as high as 66.5 cm² V⁻¹ s⁻¹ with carrier concentration of 1.5 × 10¹⁹ cm⁻³ and resistivity of 6.3 × 10⁻³ Ω cm. The absolute average transmittance of the obtained films in the visible range exceeds 95%.     

Investigations on Pr1.6Sr0.4NiO4-YSZ-Ag composite cathode for solid oxide fuel cells

Ag-network was successfully deposited by VA-EP (vacuum assisted electroless plating) method on Pr_1.6Sr_0.4NiO₄-YSZ cathode to form (1−x) wt% Pr_1.6Sr_0.4NiO₄−x wt% YSZ-Ag (x=0, 10, 20, 30, 40) (abbr. PYx-Ag) composite cathode. XRD results suggested that there was a good chemical stability between Pr_1.6Sr_0.4NiO₄ and YSZ at temperatures below 1050 °C. PY20-Ag cathode exhibited higher exchange current density, lower overpotential and ASR (Area Specific Resistance) than PY20 cathode. At 650 °C, the ASR of PY20-Ag cathode was 2.5 Ω cm², which was only about 42% of that of PY20, 5.9 Ω cm². PY20-Ag can be a promising candidate for SOFC cathode.     

Influence of substrate temperature on structures and dielectric properties of pyrochlore Bi1.5Zn1.0Nb1.5O7 thin films prepared by pulsed laser deposition

The influence of substrate temperature on structural and dielectric properties of cubic pyrochlore Bi_1.5Zn_1.0Nb_1.5O₇ (BZN) thin films prepared by pulsed laser deposition process has been investigated. BZN thin films were deposited on Pt/Ti/SiO₂/Si(1 0 0) substrate and in situ annealed at 700 °C. The results indicate that the substrate temperature has a significant effect on the structural and dielectric properties of BZN thin films. The films exhibit a cubic pyrochlore structure in the substrate temperature range from 550 °C to 700 °C and at the annealing temperature of 700 °C. With further increase of substrate temperature to 750 °C, the phases of Bi₂O₃, BiNbO₄ and Bi₅Nb₃O₁₅ can be detected in the XRD pattern due to the Zn loss. The dielectric constant and loss tangent of the films deposited at 650 °C are 192 and 6 × 10⁻⁴ at 10 kHz, respectively. The tunability is 10% at a dc bias field of 0.9 MV/cm.     

Preparation and photoluminescence characteristics of Eu-doped MgAl1.8Y0.2O4 nanocrystals

A simple combustion route was employed for the preparation of Eu³⁺-doped MgAl_1.8Y_0.2−xO₄ nanocrystals using metal nitrates as precursors and urea as a fuel in a preheated furnace at 500 °C. The powders thus obtained were then fired at 1000 °C for 3 h to get better luminescent properties. The incorporation of Eu³⁺ activator in these nanocrystals was checked by luminescence characteristics. These nanocrystals displayed bright red color on excitation under 254 nm UV source. The main emission peak was assigned to the transition [⁵D₀→⁷F₂] at 615 nm. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) studies were carried out to understand surface morphological features and the particle size. Crystal structures of the nanocrystals were investigated by the X-ray diffraction (XRD) technique. The crystallite size of the as-prepared nanocrystals was around 29 nm, which was evaluated from the broad XRD peaks. The crystallite size increased to ∼45 nm on further heat treatment at 1000 °C.     

Dielectric behavior of spin-deposited nanocrystalline nickel-zinc ferrite thin films processed by citrate-route

Nanocrystalline nickel-zinc ferrite thin films with the general formula Ni_1−xZn_xFe₂O₄, where x=0.0, 0.2, 0.4 and 0.6 were fabricated via a chemical route known as the citrate precursor route. These films were spin-deposited on indium-tin oxide coated glass, fused quartz and amorphous Si-wafer substrates, and annealed at various temperatures up to 650 °C. The films annealed below 400 °C were found to be X-ray amorphous, while the films annealed at and above 400 °C were polycrystalline exhibiting a single-phase spinel structure. The average grain size of the films evaluated by transmission electron microscopy, is found to be in the range 4-8.5 nm. The room temperature DC resistivity of the films is in the range 10³-10⁷ Ω m. Dielectric constant and dielectric loss were measured in the frequency range 100 Hz-1 MHz. Dielectric constant of the films is found to lie between 25 and 44, while the loss factor is if the order of 10⁻². The higher values of the dielectric constant for films having higher zinc concentration are attributable to the enhanced hopping between Fe²⁺ and Fe³⁺ ions in these samples. The M-H hysteresis measurement of the nickel ferrite thin films annealed at 650 °C showed narrow hysteresis loop—a characteristic of soft ferromagnetic material.     

A novel chemical synthesis and characterization of Mn3O4 thin films for supercapacitor application

Mn₃O₄ thin films have been prepared by novel chemical successive ionic layer adsorption and reaction (SILAR) method. Further these films were characterized for their structural, morphological and optical properties by means of X-ray diffraction (XRD), Fourier transform infrared spectrum (FTIR), field emission scanning electron microscopy (FESEM), wettability test and optical absorption studies. The XRD pattern showed that the Mn₃O₄ films exhibit tetragonal hausmannite structure. Formation of manganese oxide compound was confirmed from FTIR studies. The optical absorption showed existence of direct optical band gap of energy 2.30 eV. Mn₃O₄ film surface showed hydrophilic nature with water contact angle of 55°. The supercapacitive properties of Mn₃O₄ thin film investigated in 1 M Na₂SO₄ electrolyte showed maximum supercapacitance of 314 F g⁻¹ at scan rate 5 mV s⁻¹.     

Structural and optoelectronic properties of vacuum evaporated SnS thin films annealed in argon ambient

In this work, 650 nm polycrystalline SnS thin films were grown by thermal evaporation of high purity tin sulfide powder at 250 °C substrate temperature, followed by post deposition annealing at 200 °C and 300 °C for 2, 4 and 6 h, and at 400 °C for 2 and 4 h in argon ambient. The XRD pattern of the as-deposited and annealed SnS films led to the conclusion that the as-deposited films were polycrystalline in nature with preferentially oriented along (1 1 1) direction. The direct bandgap of all the films was found to be observed between 1.33 and 1.53 eV. Except for annealing at 400 °C all the films were nearly stoichiometric in nature, suggesting lower rate of desulfurization at that ambient. However, higher annealing temperature has resulted in the segregation of tin phase. All the films showed good absorption in the visible range. The as-deposited and annealed films showed p-type conductivity. Hall measurement revealed the carrier concentration and mobility ranging from 10¹⁵ to 10¹⁶ cm⁻³ and 0.8 to 31.6 cm² V⁻¹ s⁻¹ respectively. The photoconductivity measurements of all the SnS films were carried out by recording the lowering of resistance of the respective films with time under illumination.     

Luminescence and EPR studies of Eu doped BaAl12O19 blue light emitting phosphors

Europium doped BaAl₁₂O₁₉ powder phosphors have been synthesized by combustion process within few minutes. The phosphors have been characterized by XRD, SEM, FT-IR, EPR and PL techniques. The EPR spectrum exhibits an intense resonance signal at g=1.96 characteristic of Eu²⁺ ions. In addition to this two weak resonance signals have been observed at g=2.28 and g=4.86. The population of the spin levels (N) for the resonance signal at g=1.96 is calculated as a function of temperature. By post-treating the phosphor at 1350 °C under a reducing atmosphere, it is observed that the population of spin levels has been increased five times. The excitation spectrum shows a peak at 326 nm with a shoulder at 290 nm. Upon excitation at 326 nm, the emission spectrum exhibits a well defined broad band with maximum at 444 nm emitting a blue light corresponding to 4f⁶5d→4f⁷ transition. The luminescence intensity also has been enhanced to 60% by post-treating the phosphor at 1350 °C under a reducing atmosphere.     

Low temperature synthesis and superconducting properties of polycrystalline T′-(La,Sm)2CuO4

La_2−xSm_xCuO_4+δ with the Nd₂CuO₄ structure was synthesized by precipitation from fused alkaline hydroxide, CsOH, at 400 °C. The as-sintered polycrystalline samples showed no diamagnetic signal, but after post-annealing in vacuum of ≈10⁻⁸ atm at 650–700 °C, the samples with x = 0.1 and 0.3 exhibited superconductivity at T_c on = 25 K. The volume fraction of the superconducting phase estimated from the slope of the Zero-Field-Cooled magnetization data was over 30% for x = 0.3, which confirmed that the La_1.7Sm_0.3CuO_4+δ is a bulk superconductor.