Bonded dimethylacrylamide as a permanent coating for capillary electrophoresis

A method for coating capillaries for capillary electrophoresis with chemically bonded polydimethylacrylamide has been developed, and the properties of the capillaries have been evaluated. The coated capillaries provided high separation efficiency, 12 x 10(5) theoretical plates/m was obtained for cytochrome c. The electroosmotic flow at pH 8.0 was 10 x 10(-10) to 6 x 10(-10) m2 V(-1) s(-1). The coated capillaries were quite stable at high pH. At least 150 runs could be done at pH 10 without appreciable performance deterioration. The excellent performance of the coated capillaries was illustrated by separation of basic proteins, acidic proteins, 9-fluorenylmethyl chloroformate-derivatized neurotransmitter amino acids, peptide reference mixtures and peptides digested from a bacteria protein.     

Electroosmotic flow controllable coating on a capillary surface by a sol-gel process for capillary electrophoresis

A simple coating procedure employing a sol-gel process to modify the inner surface of a bare fused-silica capillary with a positively charged quaternary ammonium group is established. Scanning electron microscopic studies reveal that a smooth coating with 1 to approximately 2 microm thickness can be obtained at optimized coating conditions. With 40 mM citrate as a running electrolyte, the plot of electroosmotic flow (EOF) versus pH shows a unique three-stage EOF pattern from negative to zero and then to positive over a pH range of 2.5 to 7.0. At pH above 5.5, the direction of the EOF is from the anode to the cathode, as is the case in a bare fused-silica capillary, and the electroosmotic mobility increases as the pH increases. However, the direction of the EOF is reversed at pH below 4.0. Over the pH range of 4.0 to 5.5, zero electroosmotic mobility is obtained. Such a three-stage EOF pattern has been used to separate six aromatic acids under suppressed EOF and to separate nitrate and nitrite with the anions migrating in the same direction as the EOF. The positively charged quaternary ammonium group on the coating was also utilized to minimize the adsorption problem during the separation of five basic drugs under suppressed EOF and during the separation of four basic proteins with the cations migrate in the opposite direction as the EOF. Also, the stability and reproducibility of this column are good.     

Cycloaliphatic epoxy resin coating for capillary electrophoresis

Coating the interior surface of a fused-silica capillary with a polymeric material has long been used in capillary electrophoresis (CE) to reduce or eliminate electroosmotic flow and suppress adsorption. A cycloaliphatic epoxide-based resin was bonded to silane treated capillaries and crosslinked with a curing agent. The epoxy resin coating significantly reduced electroosmotic flow over a pH range of 3-10. This coating was sufficiently hydrophilic to suppress protein adsorption. The epoxy resin coated capillary was used to separate several acidic and basic proteins and peptides. Separation efficiencies greater than 400,000 theoretical plates were achieved. The relative standard deviations in migration times for proteins were <0.8%. Speed and simplicity are important advantages of the coating procedure compared to other published coating methods.     

Wall coating for capillary electrophoresis on microchips

This review article with 116 references describes recent developments in the preparation of wall coatings for capillary electrophoresis (CE) on a microchip. It deals with both dynamic and permanent coatings and concentrates on the most frequently used microchip materials including glass, poly(methyl methacrylate), poly(dimethyl siloxane), polycarbonate, and poly(ethylene terephthalate glycol). Characterization of the channel surface by measuring electroosmotic mobility and water contact angle of the surface is included as well. The utility of the microchips with coated channels is demonstrated by examples of CE separations on these chips.     

Characterization of a sapphire-epoxy coating for capillary electrophoresis

A new procedure for coating capillaries for capillary electrophoresis applying a sapphire (alumina) containing epoxy resin was developed. Coated capillaries showed considerably reduced electroosmotic flow, and decreased the adsorption of proteins to the internal wall of the capillary. Coating is transparent down to 195 nm and can be used with advantage to analyze different kinds of substances, such as small cations and/or anions, and proteins.     

Phospholipid-lysozyme coating for chiral separation in capillary electrophoresis

A phospholipid coating with lysozyme as chiral recognition reagent permeated into the phospholipid membrane was developed for the chiral capillary electrophoretic (CE) separation of D- and L-tryptophan. As a kind of carriers, coated as phospholipid membranes onto the inner wall of a fused-silica capillary, liposomes are able to interact with basic proteins such as lysozyme, which may reside on the surface of the phospholipid membrane or permeate into the middle of the membrane. The interaction results in strong immobilization of lysozyme in the capillary. Coatings prepared with liposomes alone did not allow stable immobilization of lysozyme into the phospholipid membranes, as seen from the poor repeatability of the chiral separation. When 1-(4-iodobutyl)-1,4-dimethylpiperazin-1-ium iodide (M1C4) was applied as a first coating layer in the capillary, the electroosmotic flow (EOF) was effectively suppressed, the phospholipid coating was stabilized, and the lysozyme immobilization was much improved. The liposome composition, the running buffer, and the capillary inner diameter all affected the chiral separation of D- and L-tryptophan. Coating with 4 mM M1C4 and then 1 mM phosphatidylcholine (PC)/phosphatidylserine (PS) (80:20 mol%), with 20 mM (ionic strength) Tris at pH 7.4 as the running buffer, resulted in optimal chiral separation with good separation efficiency and resolution. Since lysozyme was strongly permeated into the membrane of the phospholipids on the capillary surface, the chiral separation of D- and L-tryptophan was achieved without lysozyme in the running buffer. The effects of different coating procedures and separation conditions on separation were evaluated, and the M1C4-liposome and liposome-lysozyme interactions were elucidated. The usefulness of protein immobilized into phospholipid membranes as a chiral selector in CE is demonstrated for the first time.     

Cationic starch derivatives as dynamic coating additives for protein analysis in capillary electrophoresis

Positively charged starch derivatives were used to modify the inner surface of fused-silica capillaries by addition to running buffer, which were subsequently employed in capillary electrophoresis (CE). Capillaries coated with the cationic starch derivatives were shown to generate a stable, reversed electroosmotic flow (EOF) in the investigated pH range of 3-9. The presented coating procedure was fast, based on a simple rinsing protocol where the polymer created a physically adsorbed, cationic polymer layer. Among the additives studied, a quaternary ammonium starch derivative showed a fast EOF mobility and effectively suppressed the adsorption of proteins. The intra- and inter-day reproducibility of the coating referring to the EOF mobility were satisfactory with relative standard deviation (RSD) of 0.27 and 1.67%, respectively. The coating enabled separation of some protein mixtures including basic proteins within l3 min with efficiencies up to 280,000 plates/m. In addition, this cationic starch derivative possessed a good solubility (about 100mg/mL), and it does not significantly contribute to the background adsorption in the UV region of 190-400 nm.     

Bacterial surface layer proteins as a novel capillary coating material for capillary electrophoretic separations

A novel concept for stable coating in capillary electrophoresis, based on recrystallization of surface layer proteins on hydrophobized fused silica capillaries, was demonstrated. Surface layer protein A (SlpA) from Lactobacillus acidophilus bacteria was extracted, purified and used for coating pre-silanized glass substrates presenting different surface wettabilities (either hydrophobic or hydrophilic). Contact angle determination on SlpA-coated hydrophobic silica slides showed that the surfaces turned to hydrophilic after coating (53 ± 5°), due to a protein monolayer formation by protein-surface hydrophobic interactions. Visualization by atomic force microscopy demonstrated the presence of a SlpA layer on methylated silica slides displaying a surface roughness of 0.44 ± 0.02 nm. Additionally, a protein layer was visualized by fluorescence microscopy in methylated silica capillaries coated with SlpA and fluorescein isothiocyanate-labeled. The SlpA-coating showed an outstanding stability, even after treatment with 20 mM NaOH (pH 12.3). The electroosmotic flow in coated capillaries showed a partial suppression at pH 7.50 (3.8 ± 0.5 10⁻⁹ m² V⁻¹ s⁻¹) when compared with unmodified fused silica (5.9 ± 0.1 10⁻⁸ m² V⁻¹ s⁻¹). To demonstrate the potential of this novel coating, the SlpA-coated capillaries were applied for the first time for electrophoretic separation, and proved to be very suitable for the isotachophoretic separation of lipoproteins in human serum. The separations showed a high degree of repeatability (absolute migration times with 1.1–1.8% coefficient-of-variation (CV) within a day) and 2–3% CV inter-capillary reproducibility. The capillaries were stable for more than 100 runs at pH 9.40, and showed to be an exceptional alternative for challenging electrophoretic separations at long-term use.     

Brush-like copolymer as a physically adsorbed coating for protein separation by capillary electrophoresis

A brush-like copolymer consisting of poly(ethylene glycol) methyl ether methacrylate and N,N-dimethylacrylamide (PEGMA-DMA) was synthesized and used as a novel static physically adsorbed coating for protein separation by capillary electrophoresis for the first time, in order to stabilize electroosmotic flow (EOF) and suppress adsorption of proteins onto the capillary wall. Very stable and low EOF was obtained in PEGMA-DMA-coated capillary at pH 2.2-7.8. The effects of molar ratio of PEGMA to DMA, copolymer molecular mass, and pH on the separation of basic proteins were discussed. A comparative study of bare capillary with PEGMA-DMA-coated capillary for protein separation was also performed. The basic proteins could be well separated in PEGMA-DMA-coated capillary over the investigated pH range of 2.8-6.8 with good repeatability and high separation efficiency because the copolymer coating combines good protein-resistant property of PEG side chains with excellent coating ability of PDMA-contained backbone. Finally, the coating was successfully applied to the fast separation of other protein samples, such as protein mixture and egg white, which reveals that it is a potential coating for further proteomics analysis.     

Poly-N-hydroxyethylacrylamide as a novel, adsorbed coating for protein separation by capillary electrophoresis.

We present the polymer poly-N-hydroxyethylacrylamide (PHEA) (polyDuramide) as a novel, hydrophilic, adsorbed capillary coating for electrophoretic protein analysis. Preparation of the PHEA coating requires a simple and fast (30 min) protocol that can be easily automated in capillary electrophoresis instruments. Over the pH range of 3-8.4, the PHEA coating is shown to reduce electroosmotic flow (EOF) by about 2 orders of magnitude compared to the bare silica capillary. In a systematic comparative study, the adsorbed PHEA coating exhibited minimal interactions with both acidic and basic proteins, providing efficient protein separations with excellent reproducibility on par with a covalent polyacrylamide coating. Hydrophobic interactions between proteins and a relatively hydrophobic poly-N,N-dimethylacrylamide (PDMA) adsorbed coating, on the other hand, adversely affected separation reproducibility and efficiency. Under both acidic and basic buffer conditions, the adsorbed PHEA coating produced an EOF suppression performance comparable to that of covalent polyacrylamide coating and superior to that of adsorbed PDMA coating. The protein separation performance in PHEA-coated capillaries was retained for 275 consecutive protein separation runs at pH 8.4, and for more than 800 runs at pH 4.4. The unique and novel combination of hydrophilicity and adsorptive coating ability of PHEA makes it a suitable wall coating for automated microscale analysis of proteins by capillary array systems.     

New silanization coating for DNA fragment analysis by capillary electrophoresis

We propose a new coating technique for fused silica capillaries using silanization with trimethylchlorosilane and diethylamine as a mediating agent in DNA separation using capillary electrophoresis. The proposed coating technique is simple and stable at a high pH. Capillaries coated by the new preparation method give excellent reproducibility for DNA fragment analysis with a good relative standard deviation of less than 0.7% for 150 runs and good stability at pH 8.2. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1405–1420, 2002     

涂层技术在毛细管电泳手性分离中的应用

手性是自然界的本质属性之一。手性分离分析技术对生命科学、环境科学、生物工程和药物工程等许多学科都具有十分重要的意义。当前,对不同种类手性化合物进行拆分已成为毛细管电泳技术最具特色的研究和应用领域之一。然而,被分析物(或拆分剂)在毛细管内壁的吸附是毛细管电泳手性分离中的常见问题。涂层技术就是采用不同的方法对毛细管内壁进行改性,是抑制非特异性吸附、提高分离效率及分离重现性最简便和最有效的方法。本文主要综述了近十几年来各种涂层技术在毛细管电泳手性分离领域的应用现状,并对毛细管涂层技术今后的发展进行了展望。     

pH effect on dynamic coating for capillary electrophoresis of DNA

A buffer consisting of tris(hydroxymethyl)aminomethane, 2-(N-moropholino)ethanesulfonic acid (Mes) and EDTA with constant ion strength was used to investigate the effect of buffer pH on the dynamic coating behavior of poly(N-isopropylacrylamide) (PNIPAM) for DNA separation. The atomic force microscopy (AFM) image illustrated that PNIPAM in lower-pH buffer was much more efficient in covering a silica wafer than that in higher-pH buffer. The coating performance of PNIPAM was also quantitatively analyzed by Fourier transform IR attenuated total reflectance spectroscopy and by measuring the electroosmotic flow (EOF). These results indicated that the stability of the dynamic coating was dependent on the pH of the sieving matrix and was improved by reducing the pH to the weak-acid range. The lower pH of the sieving buffer may induce the polymer more efficiently to adsorb on the capillary wall to suppress EOF and DNA–capillary wall interaction for DNA separation. The enhanced dynamic coating capacity of PNIPAM in lower-pH buffer may be attributed to the hydrogen bonds between the hydroxyl groups of the silica surface and the oxygen atom of the carbonyl groups of PNIPAM.     

Cross-linked poly(vinyl alcohol) as permanent hydrophilic column coating for capillary electrophoresis.

A fast method for the generation of permanent hydrophilic capillary coatings for capillary electrophoresis (CE) is presented. Such interior coating is effected by treating the surface to be coated with a solution of glutaraldehyde as cross-linking agent followed by a solution of poly(vinyl alcohol) (PVA), which results in an immobilization of the polymer on the capillary surface. Applied for capillary zone electrophoresis (CZE) such capillaries coated with cross-linked PVA exhibit excellent separation performance of adsorptive analytes like basic proteins due to the reduction of analyte-wall interactions. The long-term stability of cross-linked PVA coatings could be proved in very long series of CZE separations. More than 1000 repetitive CE separations of basic proteins were performed with stable absolute migration times relative standard deviation (RSD > 1.2%) and without loss of separation efficiency. Cross-linked PVA coatings exhibit a suppressed electroosmotic flow and excellent stability over a wide pH range.     

Cationized hydroxyethylcellulose as a novel, adsorbed coating for basic protein separation by capillary electrophoresis

We present cationized hydroxyethylcellulose (cat-HEC) synthesized in our laboratory as a novel physically adsorbed coating for CE. This capillary coating is simple and easy to obtain as it only requires flushing the capillary with polymer aqueous solution. A comparative study with and without polymers was performed. The adsorbed cat-HEC coating exhibited minimal interactions with basic proteins, providing efficient basic protein separations with excellent reproducibility. Under broad pHs, the amine groups are the main charged groups bringing about a global positive charge on the capillary wall. As a consequence, the cat-HEC coating produced an anodal EOF performance. A comparative study on the use of hydroxyethylcellulose (HEC) and cat-HEC as physically adsorbed coatings for CE are also presented. The separation efficiency and analysis reproducibility proved that the cat-HEC polymer was efficient in suppressing the adsorption of basic proteins onto the silica capillary wall. The long-term stability of the cat-HEC coating in consecutive protein separation runs has demonstrated the suitability of the coating for high-throughput electrophoretic protein separations.     

Influence of polyelectrolyte coating conditions on capillary coating stability and separation efficiency in capillary electrophoresis

Polyelectrolytes are widely used in capillary electrophoresis as coating agents of silica capillaries to prevent adsorption phenomena and improve the repeatability of peptide and protein analysis. A systematic study of the coating experimental conditions has been carried out to optimize coating stability and performance. The main experimental parameters studied were the type and concentration of polyelectrolytes used in several monolayer and multilayer coatings, the ionic strength of coating and stabilizing solutions, and the procedures used for coating and capillary storage. Electroosmotic flow magnitude, direction and repeatability were used to monitor coating stability. Coating ability to limit adsorption was investigated by monitoring variations of migration times, time-corrected peak areas and separation efficiency of test peptides. Capillary-to-capillary and batch-to-batch reproducibility was also studied. In addition, the separation performance of polyelectrolyte coatings were compared to those obtained with bare silica capillaries.     

Preparation and evaluation of stable coating for capillary electrophoresis using coupled chitosan as coated modifier

A coated capillary modified with a coupled chitosan (COCH) was developed by using a simple and fast (60 min) process that could be easily automated in capillary electrophoresis instrument. The COCH coating was achieved by first attaching chitosan to the capillary inner wall, and then coupling with glutaraldehyde, and rinsing chitosan again to react with glutaraldehyde. The COCH coating was stable and showed amphoteric character over the pH range of 1.8-12.0. When the pH value was lower than 4.5, the capillary surface possessed positive charges, which caused a reversal in the direction of the electroosmotic flow (EOF). The normal EOF direction could be obtained when the pH value was higher than 4.5. The COCH coating showed strong stability against 0.1 mol/L HCl, 0.1 mol/L NaOH and other solvents compared with conventional chitosan coating. The relative standard deviation of the run-to-run, day-to-day and capillary-to-capillary coating was all below 2% for the determination of EOF. The COCH-modified capillary was applied to acidic and basic proteins analyses and high efficiency could be attained. The comparison between unmodified capillary, chitosan-modified and COCH-modified capillary for the separation of real sample, extract from Elaphglossum yoshinagae with water, was also studied. Better results could be obtained on COCH-modified capillary than the other two capillaries.     

Performance of metal complex substituted polysiloxanes in capillary electrophoresis and capillary electrochromatography

Two novel polysiloxanes containing the metal complex, Co(TACN)(3+)2 (TACN= 1,4,7-triazacyclononane) were used as coatings for capillary electrophoresis (CE) and capillary electrochromatography (CEC). Through crosslinking and covalent bonding, the positively charged polymers were bonded to silica supports. In both CE and CEC, these coatings exhibited strong, pH-independent, and anodic electroosmotic flow (EOF), and had excellent long-term stability. Successful separations of aromatic acids were achieved in CE. In CEC, separation of alkylbenzenes (7 min) and basic compounds (20 min) was achieved with higher resolving power than conventional octadecyl silica packings. These polymers represent a new class of coatings for CE and CEC that generate pH-independent EOF.     

Separation of quaternary ammonium diastereomeric oligomers by capillary electrophoresis

The separation of novel diastereomeric trimers (3M) and pentamers (5M), derived from quaternary ammonium salts, was studied in conventional, uncoated and coated capillaries using capillary zone electrophoresis (CZE) with a variety of buffers and additives. Resolution of 5M diastereomers was best achieved using gamma-cyclodextrin (gamma-CD) as a chiral selector, while no diastereomeric resolution was realized for the 3M material.     

A new absorbed coating for DNA fragment analysis by capillary electrophoresis

A fully automated coating procedure was devised based on adsorption of a new polymer, poly(dimethylacrylamide-co-allyl glycidyl ether) onto the capillary surface. The whole procedure takes less than 30 min and does not require the use of organic solvents, viscous solutions, or elevated temperature. The coating is stable even under harsh conditions such as alkaline pH, elevated temperature, and denaturant conditions that destroy most other presently available adsorbed coatings. This new adsorbed coating is highly stable and easy to produce in quantity, making it quite unique, and further making it possible to operate with any DNA sieving matrix. Finally, the above-mentioned properties facilitate coating regeneration by a simple wash with a strongly alkaline solution, thus extending the lifetime of the capillary, a highly desirable property for any coating used in biopolymer separations.