基于近似熵测度的铝合金P-MIG焊亚射流过渡自适应控制研究

铝合金熔化极惰性气体保护焊(MIG)的亚射流过渡方式具有弧长调节作用强、焊缝成形美观的优点.本文从非线性动力学近似熵测度的角度对铝合金脉冲MIG焊的电弧电压信号进行分析,进而评价自适应控制模式针对亚射流过渡方式的适用性;讨论在自适应控制模式下,改变工艺参数和熔滴过渡方式时,近似熵值的变化;并对比自适应控制与普通脉冲控制在射滴过渡方式下的近似熵值大小.结果表明近似熵越小,自适应控制越成功,控制越有效. 关键词： 自适应控制 亚射流过渡 熔化极惰性气体保护焊(MIG) 近似熵     

半导体光磁电效应的非线性特征

本文从Shockley-Read统计出发,引入载流子寿命与浓度的相关性,将载流子的输运方程化为二阶非线性微分方程,并用双参数摄动法找到了方程的一般解,且在二级近似下,计算了半导体材料的短路电流和光导电流,揭示了大信号情况下光磁电效应的非线性特征,进一步拟合了实验数据。 关键词：     

两种熵测度在量化射击运动员短时心率变异性信号复杂度上的一致性

利用两种基于熵的非线性复杂度测度：近似熵和样本熵,研究了专业射击运动员两种不同状态下(休息和练习赛)心率变异性信号的复杂度.计算结果表明：射击运动员休息时其心率变异性信号的熵值大于射击比赛时信号的熵值,这意味着运动员一旦进行射击比赛时,其心率变异性信号复杂度降低了,心跳变得更为规则了.为了更好地应用这两种基于熵的方法,进一步分析了算法中的两个重要影响因素：矢量匹配容差r和序列长度N对算法性能的影响.分析结果表明：只要参数选择在合适的范围内,近似熵和样本熵都能够正确地区分出两种不 关键词： 近似熵 样本熵 复杂度 射击     

基于近似熵测度的自适应随机共振研究

变步长随机共振算法有效解决了绝热近似大参数条件下的弱信号检测问题.基于信号近似熵测度的自适应随机共振，实现了变步长随机共振最优输出的自适应求解.周期信号的近似熵不受其幅值和相位变化的影响，而只与其频率及信噪比有关.因此，按照原始数据的采样条件，构造待检测频率在预定信噪比下的标准信号，并以其近似熵为基准，通过自动调节非线性系统的结构参数和计算步长，求得系统输出的近似熵距离矩阵.该矩阵中的最小值所对应的即为自适应条件下非线性动力系统的最优参数.     

相对转动非线性动力系统的稳定性与强迫激励下的近似解

研究相对转动非线性动力系统的运动稳定性.建立具有一般广义阻尼力和外扰激励的一类两质量相对转动非线性动力系统的动力学方程.研究相对转动非线性动力自治系统的稳定性，证明系统在一定条件下可发生闭轨分岔.应用多尺度法得到强迫激励下非自治系统的近似解. 关键词： 相对转动 非线性动力系统 运动稳定性 近似解     

基于近似熵的突变检测新方法

近似熵是一个有效的非线性动力学指数,能够用于表征时间序列的复杂性,通过滑动窗口技术,近似熵对于一维时间序列的动力学结构突变具有一定的识别能力,但其突变检测结果依赖于子序列长度的选择,且不能准确定位突变点.鉴于此,本文提出了一种新的突变检测方法——滑动移除近似熵.测试结果表明,滑动移除近似熵具有检测结果稳定性好、准确性高等特点,明显优于滑动近似熵和Mann-Kendall方法,其在实际观测资料中的应用进一步证实了新方法的可靠性. 关键词： 近似熵 滑动移除近似熵 突变检测     

二端面转轴相对转动非线性动力学系统的稳定性与近似解

建立了二端面转轴相对转动系统的非线性动力学方程.对于等力矩的动力学方程进行了定性分析，得到了方程的稳定性等性质.用平均方法求得方程在一定条件下的近似解. 关键词： 非线性动力学方程 稳定性 极限环 近似解     

AuZn和AuAl分子基态与低激发态的势能函数与热力学性质

用密度泛函理论B3LYP方法计算研究AuZn和AuAl分子基态与低激发态的结构与势能函数,导出分子的光谱数据.结果表明,AuZn和AuAl分子基态分别为X²Σ和X¹Σ,基态与低激发态的势能函数均可用Murrell-Sorbie函数来表达.AuZn分子低激发态a⁴Σ的绝热激发能为43529kJ/mol,AuAl分子低激发态a³Σ的绝热激发能为19991kJ/mol.计算固体AuZn和AuAl的内能和熵时,近似以气体分子的电子能和振动能代替固体分子的内能,用电子熵和振动熵代替固体分子的熵.在此近似下,计算得到AuZn和AuAl基态与低激发态固态分子生成反应热力学性质与温度的关系. 关键词： AuZn和AuAl B3LYP 热力学性质 势能函数     

一类谐波激励相对转动非线性动力系统的稳定性与近似解

建立具有一般非线性弹性力、广义摩阻力和谐波激励的一类相对转动非线性动力系统的动力学方程. 对相对转动非线性自治系统进行定性分析,通过构造Lyapunov函数研究自治系统奇点的稳定性. 运用多尺度法求解谐波激励下非自治系统在几种不同共振响应下的近似解,同时分析了主振系统稳态运动的稳定性. 关键词： 相对转动 非线性动力系统 Lyapunov函数 稳定性     

采用AES深度刻蚀研究不同氧气含量下短路熔痕的成分

火灾中短路发生时周围的环境气氛对短路时导线上形成的熔化痕迹特征具有决定性影响。为了探讨环境气氛中氧浓度对短路熔痕特征的影响,文章对木材、纸板、泡沫、橡胶、塑料等典型燃烧物燃烧时燃烧部位的氧气浓度进行了测定,确定了典型燃烧物燃烧时燃烧部位氧气浓度的极限条件。选择100% N₂, 10% O₂+90% N₂和20% O₂+80% N₂三种浓度的试验气体,分别在3种气体环境下进行短路实验,然后对得到的短路熔痕样品进行AES深度剖析,得出短路熔痕样品表层平均氧含量与环境氧浓度成近似线性的对应关系。因此可以根据测得的氧浓度,确定出短路发生时的周围环境气氛条件,推断其与火灾发生的关系,进一步推断火灾原因。     

Approximate entropy a new statistic to quantify arc and welding process stability in short-circuiting gas metal arc welding

Based on the phase state reconstruction of welding current in short-circuiting gas metal arc welding using carbon dioxide as shielding gas, the approximate entropy of welding current as well as its standard deviation has been calculated and analysed to investigate their relation with the stability of electric arc and welding process. The extensive experimental and calculated results show that the approximate entropy of welding current is significantly and positively correlated with arc and welding process stability, whereas its standard deviation is correlated with them negatively. A larger approximate entropy and a smaller standard deviation imply a more stable arc and welding process, and vice versa. As a result, the approximate entropy of welding current promises well in assessing and quantifying the stability of electric arc and welding process in short-circuiting gas metal arc welding.     

Short-circuiting in fullerene devices studied by in situ electrical measurement in high vacuum and infrared imaging analysis

In the present work, current–voltage (I–V) characteristics of fullerene devices (ITO⧹C₆₀⧹Al) are reexamined by in situ electrical measurement in high vacuum and by infrared imaging analysis. Two kinds of I–V curves are detected: ‘ohmic’ and nonohmic. Degradation processes of the two different devices are measured, and ‘ohmic’ degradation processes are ascribed to short-circuiting. ITO⧹C₆₀⧹Al devices in high vacuum are confirmed to be intrinsically nonohmic. Surface temperature distribution of the two different devices is measured and localized heat is detected further confirming the existence of short-circuiting in ‘ohmic’ devices. To avoid short-circuit, organic buffers are inserted between fullerene layer and cathode and this is found to be effective.     

The influence of shielding gas in hybrid LASER-MIG welding

Hybrid LASER-GMAW welding technique has been recently studied and developed in order to meet the needs of modern welding industries. The two sources involved in this process play, in fact, a complementary role: fast welding speed, deep bead penetration and high energy concentration can be achieved through the LASER beam, while gap bridgeability and cost-effectiveness are typical of the GMAW process.Particularly interesting, in this context, is the CO₂ LASER-MIG welding which differs from the Nd:YAG LASER-MIG technique for the high powers that can be exploited and for the good power/cost ratio of the process.This paper is a part of a wide study on the hybrid CO₂ LASER-MIG welding and investigates the influence of the shielding gas both on the stability of the process and on the dimensional characteristics of the weld bead. Two different parameters have been taken into consideration in order to develop this analysis: the shielding gas composition and the shielding gas flow.The experiment, performed on AISI 304 stainless steel plates, has been planned exploiting design of experiment techniques. The results have been analyzed through a statistical approach in order to determine the real influence of each parameter on the overall process.     

Research on laser welding of vehicle body

Based on many experiments of CO₂ laser welding of vehicle body, joint microstructure and stress–strain curve of specimen are analyzed. The deep punching performance acquired by adopting Ar as protective gas is better than that of the one acquired by adopting N₂ as protective gas. Meanwhile the percentage of zinc in welding seam can be effectively controlled by means of blowing side protective gas. In this paper, welding penetration and width are shown to vary with laser power and speed of welding. The results indicate that some flaws such as gas hole, crack and softening of HAZ do not appear in laser welding seam in sheet steel of automobile bodies if technology parameters optimizes. The deep punching performance of tailor-welding sheet is fine.     

相空间中脑电近似熵和信息熵的计算

提出一种基于相空间重构脑电信号来计算脑电近似熵和信息熵的新方法．实验计算结果表明，癫痫患者脑电和正常人脑电的近似熵和信息熵随相空间嵌入维数的变化有明显的不同．     

旁路耦合电弧焊温度场模拟及验证

针对旁路耦合电弧焊的特点, 建立了一种适于用旁路耦合电弧焊的复合热源模型. 利用该热源模型对不同焊接参数下的旁路耦合电弧焊温度场进行了数值分析, 得到了总电流相同时不同旁路电流下的焊缝熔深、母材温度和特征点焊接热循环曲线的模拟结果, 分析了旁路耦合电弧焊焊接参数对母材热输入的影响, 并将特征点热循环曲线的模拟结果与相同条件下的试验结果进行了比较. 结果表明, 焊接总电流相同时母材热输入随着旁路电流的增加而降低, 且越靠近焊缝母材热输入的降幅越大, 特征点焊接热循环曲线的模拟结果与试验结果基本一致, 旁路耦合电弧焊温度场模型是合理的, 所建立的热源模型能够正确反映焊接参数与母材热输入之间的关系.     

混沌伪随机序列复杂度分析的符号动力学方法

通过将混沌伪随机序列看成一个符号序列，提出了用符号动力学的 方法来分析混沌伪随机序列的复杂度.以Logistic映射和耦合映射格子系统产生的混沌伪随 机序列为例，说明了该方法的应用，并将计算结果与近似熵ApEn法的计算结果作了比较.结 果表明，该方法可以有效地判断出不同的混沌伪随机序列的复杂程度，而且比近似熵法更为 优越. 关键词： 混沌 伪随机序列 符号动力学 熵     

Dissimilar autogenous full penetration welding of superalloy K418 and 42CrMo steel by a high power CW Nd:YAG laser

Experiments of autogenous laser full penetration welding between dissimilar cast Ni-based superalloy K418 and alloy steel 42CrMo flat plates with 3.5 mm thickness were conducted using a 3 kW continuous wave (CW) Nd:YAG laser. The influences of laser welding velocity, flow rate of side-blow shielding gas, defocusing distance were investigated. Microstructure of the welded seam was characterized by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) and energy dispersive spectrometer (EDS). Mechanical properties of the welded seam were evaluated by microhardness and tensile strength testing. Results show that high quality full penetration laser-welded joint can be obtained by optimizing the welding velocity, flow rate of shielding gas and defocusing distance. The laser-welded seam have non-equilibrium solidified microstructures consisting of γ-FeCr_0.29Ni_0.16C_0.06 austenite solid solution dendrites as the dominant and very small amount of super-fine dispersed Ni₃Al γ′ phase and Laves particles as well as MC needle-like carbides distributed in the interdendritic regions. Although the microhardness of the laser-welded seam was lower than that of the base metal, the strength of the joint was equal to that of the base metal and the fracture mechanism showed fine ductility.