Structure and magnetic properties of Sn1−xMnxO2

The microstructure and magnetic properties have been investigated systematically for Sn_1−xMn_xO₂ polycrystalline powder samples with x=0.02-0.08 synthesized by a solid-state reaction method. X-ray diffraction revealed that all samples are pure rutile-type tetragonal phase and the cell parameters a and c decrease monotonously with the increase in Mn content, which indicated that Mn ions substitute into the lattice of SnO₂. Magnetic measurements revealed that all samples exhibit room temperature ferromagnetism. Furthermore, magnetic investigations demonstrate that magnetic properties strongly depend on doping content, x. The average magnetic moment per Mn atom decreases with increase in the Mn content, because antiferromagnetic super-exchange interaction takes place within the neighbor Mn³⁺ ions through O²⁻ ions for the samples with higher Mn doping. Our results indicate that the ferromagnetic property is intrinsic to the SnO₂ system and is not a result of any secondary magnetic phase or cluster formation.     

No room temperature ferromagnetism in Mn over-doped Zn1−xMnxO (x>0.02)

Mn-doped ZnO samples having composition Zn_1−xMn_xO (x=0.02, 0.04 and 0.05) were synthesized by solid state reaction technique with varying concentration of Mn from 0.02 to 0.05. Evidence of room temperature ferromagnetism was observed only in the composition Zn_0.98Mn_0.02O sintered at 500 °C. Our XRD pattern confirms the presence of Mn₃O₄ impurity phase in all the Zn_1−xMn_xO samples with the exception of Zn_0.98Mn_0.02O. We emphasize that the appearance of Mn₃O₄ phase in the system forbids the exchange type of interaction between the Mn ions and suppresses the ferromagnetism in all the Mn over-doped Zn_1−xMn_xO (x>0.02) system. SEM microstructure study also supports the interruption of exchange type of interaction inside the system with the increase in Mn concentration in the sample. Interestingly, for this particular composition, Zn_0.98Mn_0.02O sintered at 500 °C, glassy ferromagnetism type of transition is observed at low temperature. This type of transition is attributed to the formation of the oxides of Mn clusters at low temperature.     

Room-temperature ferromagnetism in Zn1−xMnxO

In view of recent controversies on above room-temperature ferromagnetism (RTFM) in transition-metal-doped ZnO, the present paper aims to shed some light on the origin of ferromagnetism by investigating annealing effects on structure and magnetism for polycrystalline Zn_1−xMn_xO powder samples prepared by solid-state reaction method and annealed in air at different temperatures. Magnetic measurements indicate that the samples are ferromagnetic at room temperature (RTFM). Room temperature ferromagnetism has been observed in the sample annealed at a low temperature of 500 °C with a saturated magnetization (M_s) of 0.159 emu/g and a coercive force of 89 Oe. A reduction in RTFM is clearly observed in the sample annealed at 600 °C. Furthermore, the saturation magnetic moment decreases with an increase in grain size, suggesting that ferromagnetism is due to defects and/or oxygen vacancy confined to the surface of the grains. The experimental results indicate that the ferromagnetism observed in Zn_1−xMn_xO samples is intrinsic rather than associated with secondary phases.     

Effect of Sr concentration on microstructure and magnetic properties of (Ba1−xSrx)(Ti0.3Fe0.7)O3 ceramics

Fe-doped (Ba_1−xSr_x)TiO₃ ceramics were prepared by solid-state reaction, and ferromagnetism was realized at room temperature. The microstructure and magnetism were modified by the Sr concentration control (0≤x≤75 at%) at a fixed Fe concentration, and the relevant magnetic exchange mechanism was discussed. All the samples are shown to have a single perovskite structure. When increasing the Sr concentration, the phase structure is transformed from a hexagonal perovskite into a cubic perovskite, with a monotonic decrease in lattice parameters induced by ionic size effect. The room-temperature ferromagnetism is expected to originate from the super-exchange interactions between Fe³⁺ on pentahedral and octahedral Ti sites mediated by the O²⁻ ions. The increase in Sr addition modifies two main influencing factors in magnetic properties: the ratio of pentahedral to octahedral Fe³⁺ and the concentration of oxygen vacancies, leading to a gradually enhanced saturation magnetization. The highest value, obtained for Fe-doped (Ba_0.25Sr_0.75)TiO₃, is an order of magnitude higher than that of the Fe-doped BaTiO₃ system with similar Fe concentration and preparation conditions, which may indicate (Ba_1−xSr_x)TiO₃ as a more suitable matrix material for multiferroic research.     

The magnetic behavior of La1−xTbxMn2Si2 (0≤x≤0.3) in weak magnetic fields

The structure and magnetic properties of La_1−xTb_xMn₂Si₂ (0≤x≤0.3) were studied by X-ray powder diffraction and DC magnetization measurements. All the compounds crystallize in ThCr₂Si₂-type structure. Substitution of Tb for La led to a linear decrease in the lattice constants and the unit-cell volume. A ferromagnetic phase for x≤0.15, and an antiferromagnetic phase for x=0.3 have been observed at about room temperature, whereas the compounds with x=0.2 and 0.25 exhibit a magnetic phase transition from ferromagnetism to antiferromagnetism.     

Structural and Magnetic Properties of NiFe2−2xSnxCuxO4

The substituted nickel ferrite (NiFe_2−2xSn_xCu_xO₄, x=0, 0.1, 0.2, 0.3) was prepared by the conventional ceramic method. The effect of substitution of Fe³⁺ ions by Sn⁴⁺ and Cu²⁺ cations on the structural and magnetic properties of the ferrite was studied by means of ⁵⁷Fe Mössbauer spectroscopy, alternating gradient force magnetometry (AGFM) and Faraday balance. Whereas undoped NiFe₂O₄ adopts a fully inverse spinel structure of the type (Fe)[NiFe]O₄, Sn⁴⁺ and Cu²⁺ cations tend to occupy octahedral positions in the structure of the substituted ferrite. Based on the results of Mössbauer spectroscopic measurements, the crystal-chemical formula of the substituted ferrite may be written as (Fe)[NiFe_1−2xSn_xCu_x]O₄, where parentheses and square brackets enclose cations in tetrahedral (A) and octahedral [B] coordination, respectively. The Néel temperature and the saturation magnetization values of the NiFe_2−2xSn_xCu_xO₄ samples were found to decrease with increasing degree of substitution (x). The variation of the saturation magnetization with x measured using the AGFM method and that calculated on the basis of the Mössbauer spectroscopic measurements are in qualitative agreement.     

Study of the local micro-structure and magnetic and transport properties of CrxGe1−x thin films

The local micro-structure as well as the magnetic and transport properties of Cr_xGe_1−x films prepared by means of magnetron sputtering have been investigated. Structural analysis shows that Cr atoms are situated in substitutional sites in the Ge lattice. Electrical transport properties indicate that Cr introduces a shallow acceptor level at 0.016 eV from the valence band implying Cr substituting for Ge. The low temperature ferromagnetism observed in the films is mediated mainly by ferromagnetic superexchange interactions between diluted Cr ions.     

Electronic structure and ferromagnetism of polycrystalline Zn1−xCoxO (0≤x≤0.15)

The electronic structure of polycrystalline ferromagnetic Zn_1−xCo_xO (0.05≤x≤0.15) and the oxidation state of Co in it, have been investigated. The Co-doped polycrystalline samples are synthesized by a combustion method and are ferromagnetic at room temperature. XPS and optical absorption studies show evidence for Co²⁺ ions in the tetrahedral symmetry, indicating substitution of Co²⁺ in the ZnO lattice. However, powder XRD and electron diffraction data show the presence of Co metal in the samples. This give evidence to the fact that some Co²⁺ ion are incorporated in the ZnO lattice which gives changes in the electronic structure whereas ferromagnetism comes from the Co metal impurities present in the samples.     

Investigations on structural and optical properties of Zn1−xGdxS nanoparticles

Zn_1−xGd_xS (x = 0.00, 0.02 and 0.04) nanoparticles were synthesized by facile chemical co-precipitation method using PVP as a surfactant. ZnS nanoparticles could be doped with Gd ions during synthesis without altering the XRD patterns of ZnS. Also, the pattern of the powders showed cubic zincblende structure. The particle size obtained from the XRD studies lies in the range 3-5 nm, whereas from TEM analysis it is 4 nm for x = 0.02 sample. The UV-Vis absorption spectra revealed that Zn_1−xGd_xS nanoparticles exhibit strong confinement effect as the blue shift in the absorption spectra with that of the undoped ZnS. The photoluminescence spectra showed enhanced luminescence intensity and the entry of Gd into host lattice.     

Structural,optical, FTIR and photoluminescence properties of Zn0.96−xCo0.04CuxO (x=0.03, 0.04 and 0.05) nanopowders

Un-hydrogenated and hydrogenated Cu, Co co-doped ZnO (Zn_0.96−xCo_0.04Cu_xO, x=0.03, 0.04 and 0.05) nanopowders have been synthesized by co-precipitation method. The synthesized samples have been characterized by powder X-ray diffraction, energy dispersive X-ray spectra, UV–Visible spectrophotometer and Fourier transform infrared spectroscopy. The calculated average crystalline size increases from 37.3 to 50.6 nm for un-hydrogenated samples from x=0.03 to 0.05 and it changes from 29.4 to 34.9 nm for hydrogenated samples. The change in lattice parameters, micro-strain, a small shift of X-ray diffraction peaks towards lower angles and reduction in energy gap reveal the substitution of Cu²⁺ ions into Zn–Co–O lattice. The hydrogenation effect reduces the particle size and induces the more uniform distribution of particles than the un-hydrogenated samples which is confirmed by SEM micrographs. Photoluminescence spectra of Zn_0.96−xCo_0.04Cu_xO system shows that red shift in near band edge ultraviolet emission from 393 to 403 nm with suppressing intensity and a blue shift in green band emission from 537 to 529 nm with enhancing intensity confirms the substitution of Cu into the Zn–Co–O lattice.     

Magnetic and magneto-optical studies on Zn1−xCrxTe (x=0.05) films grown on glass substrate

Zn_1−xCr_xTe (x=0.05) films were prepared by thermal evaporation onto glass substrates. X-ray diffraction (XRD) was used to determine the crystalline quality of the ZnTe:Cr film. Magnetic force microscopy (MFM) investigation has shown a non-uniform distribution of magnetic domains with an average size of 4 nm at room temperature. SQUID measurements have further shown that the non-uniform distribution of domains does not affect the room temperature ferromagnetism of this material. Electron spin resonance spectroscopy (ESR) was done to determine the Cr valence state in the ZnTe lattice. Magnetic circular dichroism (MCD) analysis was used to confirm the ZnCrTe phase contributing to the ferromagnetic behavior.     

Magnetic properties of Mn-rich Rh2Mn1+xSn1−x Heusler alloys

X-ray powder diffraction and magnetization measurements have been carried out on Rh₂Mn_1+xSn_1−x (0≤x≤0.3) alloys. The alloys, which crystallize in the L2₁ structure, were found to exhibit ferromagnetic behavior. The lattice constant a at room temperature decreases with increasing x, whereas the Curie temperature T_C decreases linearly. At 5 K the magnetic moment per formula unit first increases with increasing x and then saturates for x≥0.2. The experimental results are discussed in terms of the influence of the Mn-Mn exchange interactions between the Mn atoms on the Sn and Mn sites.     

Magnetic and transport properties of SmCoAsO1−xFx

A series of SmCoAsO_1−xF_x (with x=0, 0.05, 0.1, and 0.2) samples have been prepared by solid state reactions. X-ray powder diffraction proved that all samples can be indexed as a tetragonal ZrCuSiAs-type structure. A clear shrinkage of the lattice constants a and c with increasing F content indicated that F has been doped into the lattice. The magnetic and transport properties of the samples have been investigated. Parent SmCoAsO compound exhibited complicated magnetism including antiferromagnetism, ferromagnetism, and ferrimagnetism. For the fluorine doped samples, the antiferromagnetic Néel temperatures were almost independent of the F content and metamagnetic transitions were observed below antiferromagnetic Néel temperatures. With increasing F content, high temperature (below 142 K) ferrimagnetic state gradually changed to ferromagnetic state. In the resistivity result, metallic conduction in the region of 2-300 K and Fermi liquid behavior at low temperatures were shown in all samples. Transport properties at applied magnetic fields showed anomalies at low temperatures.     

Effect of Cr substitution on the multiferroic properties of BiFe1 − xCrxO3 compounds

Single-phase BiFe_1 − xCr_xO₃ (x=0, 0.05 and 0.1) compounds are synthesized by a sol-gel process. The lattice parameters decrease and the magnetizations increase with the Cr content. Moreover, the magnetoelectric coupling between magnetic order and ferroelectric order at room temperature was enhanced.     

Influence of doping concentration on room-temperature ferromagnetism for Fe-doped BaTiO3 ceramics

Ba(Ti_1−xFe_x)O₃ ceramics (x=7, 30 and 70 at%) were prepared by solid-state reaction. All samples are single-phase with 6H-BaTiO₃-type hexagonal perovskite structure. Mössbauer spectra show all Fe atoms to be present as Fe³⁺ in BaTiO₃ lattice, occupying M1 octahedral and pentahedral sites. Room-temperature ferromagnetism is exhibited and saturation magnetization gradually decreases with increasing Fe content. The observed ferromagnetism is considered to be an intrinsic property of Ba(Ti_1−xFe_x)O₃, originating from super-exchange interactions between Fe³⁺ in different occupational sites associated with oxygen vacancies. The variation in magnetization with Fe content is related to the ratio of pentahedral to octahedral sites and oxygen vacancies.     

Room temperature ferromagnetism behavior of Sn1−xMnxO2 powders

In this paper, we have investigated Mn-doped SnO₂ powder samples prepared by solid-state reaction method. X-ray diffraction showed a single phase polycrystalline rutile structure. The atomic content of Mn ranged from ∼0.8 to 5 at%. Room temperature M-H loops showed a ferromagnetic behavior for all samples. The ferromagnetic Sn_0.987Mn_0.013O₂ showed a coercivity H_c=545 Oe, which is among the highest reported for dilute magnetic semiconductors. The magnetic moment per Mn atom was estimated to be about 2.54 μ_B of the Sn_0.9921Mn_0.0079O₂ sample. The average magnetic moment per Mn atom sharply decreases with increasing Mn content, while the effective fraction of the Mn ions contributing to the magnetization decreases. The magnetic properties of the Sn_1−xMn_xO₂ are discussed based on the competition between the antiferromagnetic superexchange coupling and the F-center exchange coupling mechanism, in which both oxygen vacancies and magnetic ions are involved.     

The effect of Co ion implantation on Ge1−xMnx films

Ge_1−xMn_x (x = 0, 0.013, 0.0226, 0.0339, 0.0565, 0.0678, 0.0904, 0.113) films prepared by magnetron sputtering at 773 K had a Ge cubic structure except for x = 0.1130. Co ion implantation into these films can effectively prevent the formation of a second phase. Both single-doped and co-doped samples were ferromagnetic at room temperature. The d-d exchange interaction between the interstitial Mn (MnT) and the substituted Mn (Mn_Ge) resulted in ferromagnetism in the sputtered films. Since Co ion implantation destroyed the Mn_T-Mn_Ge-Mn_T complex, the saturated magnetization decreased. Hall measurements revealed that the Co ion implanted films were n-type semiconductors, and the anomalous Hall Effect (AHE) suggested the ferromagnetism was carrier-mediated in the implanted films.     

Structural, transport, and magnetic properties in the Ti-doped manganites LaMn1−xTixO3 (0≤x≤0.2)

The magnetism and transport properties of the samples LaMn_1−xTi_xO₃ (0≤x≤0.2) were investigated. All samples show a rhombohedral structure () at room temperature. The sample with x=0 undergoes the paramagnetic-ferromagnetic (PM-FM) transition accompanied by an insulator-metal (I-M) transition due to the oxygen excess. The doped samples show ferromagnetism and cluster behavior at low temperatures. Though no I-M transition associated with the PM-FM transition appears, the magnetoresistance (MR) effect was observed especially at low temperatures under the applied fields of 0.5 T. Due to the fact that the oxygen content in the Ti-doped samples is nearly stochiometry (3.01) and the Hall resistivity at room temperature is negative, the ferromagnetism in LaMn_1−xTi_xO₃ (0.05≤x≤0.2) is believed to be consistent with the Mn²⁺-O-Mn³⁺ double exchange (DE) mechanism. These results suggest that DE can be obtained by direct Mn-site doping.     

Room temperature ferromagnetism in Fe doped CuO nanorods

One dimensional CuO and Fe doped CuO nanorods have been synthesized by template free solution phase hydrothermal methods. The typical diameter and the length of the Cu_1−xFe_xO nanorods (x=0, 0.02, 0.05, 0.10) are 20-25 and 300-400 nm. Pure CuO nanorods show weak ferromagnetism and the introduction of Fe within CuO lattice improves significantly the ferromagnetic property with the Curie temperature far above room temperature. The shape anisotropy is the key point to understand ferromagnetism in Fe doped CuO nanorods.     

Spin resonant optical four wave mixing in Pb1−xSnxTTe epitaxial layers and in Pb1−xSnx/PbTe superlattices

Spin resonances of the third-order non-linear susceptibility of epitaxial layers of n- and p-type Pb_1?xSn_xTe and Pb_1?xSn_xTe/PbTe superlatttices have been observed by four photon mixing of the radiation of two CO₂-lasers. Precise data on the effective g-values of the electrons and holes of Pb_1?xSn_xTe were obtained. These data and the results of magneto-optical interband absorption measurements are used to obtain k·p parameters within the Mitchell and Wallis band model. In the Pb_1?xSn_xTe/PbTe superlattices, the same g-values for electrons as in the Pb_1?xSn_xTe films with the same composition x are found. Consequently, the electrons in the superlattices are confined within the Pb_1?xSn_xTe layers. Therefore the Pb_1?xSn_xTe/PbTe system forms a type I and not a staggered superlattice.