Critical behaviour and magnetic properties of A-B spinel ZnxCu1−xFe2O4

Polycrystalline Zn_0.6Cu_0.4Fe₂O₄ ferrites have been prepared using a solid-state reaction technique. Their structural and magnetic properties have been studied, using X-ray diffraction and Mössbauer and magnetic measurements. These results have been compared to a more general theoretical study, on Zn_xCu_1−xFe₂O₄, based on mean field theory and high-temperature series expansions (HTSE), and extrapolated with the Padé approximant method. The nearest neighbour super-exchange interactions for the intra-site and the inter-site of Zn_xCu_1−xFe₂O₄ spinel ferrites, in the range 0≤x≤1, have been computed using the probability approach, based on Mössbauer data. The Curie temperature T_C is calculated as a function of Zn concentration. The theoretical results obtained are in good agreement with the experimental results obtained by magnetic measurements.     

Reentrant spin glass behavior and large initial permeability of Co0.5−xMnxZn0.5Fe2O4

A series of polycrystalline ferrites having nominal chemical composition Co_0.50−xMn_xZn_0.5Fe₂O₄ (0<x<0.4) have been synthesized by the solid-state reaction technique. The XRD analysis confirms single phase cubic spinel structure for all compositions. Lattice constant increases from 0.84195 to 0.84429 nm with the increasing Mn content and obeys Vegard's law. The average grain size increases by increasing both Mn content and sintering temperatures. Room temperature saturation magnetization increases for x=0.1 and decreases for increasing Mn content. The coercivity decreases with increasing Mn content due to the decrease of anisotropy constant. A reentrant spin glass behavior of these samples is observed from the zero field cooled magnetization measurements. The real part of the initial permeability increases by increasing both Mn content and sintering temperatures. This is due to the homogeneous grain growth and densification of the ferrites. The highest initial permeability 137 is observed for x=0.4 sintered at 1573 K on the other hand, the highest relative quality factor (2522) is obtained for the sample Co_0.2Mn_0.3Zn_0.5Fe₂O₄ sintered at 1523 K. The Mn substituted Co_0.50−xMn_xZn_0.5Fe₂O₄ ferrites showed improved magnetic properties.     

Magnetic,electronic and structural properties of ZnxFe3−xO4

A series of samples Zn_xFe_3−xO₄ have been prepared by the chemical coprecipitation technique and characterized by X-ray diffraction (XRD), vibrating sample magnetometry (VSM) and X-ray photoelectron spectroscopy (XPS). XRD demonstrates all the samples of Zn_xFe_3−xO₄ have a spinel structure same as Fe₃O₄. The magnetic hysteresis loops of Zn_xFe_3−xO₄ obtained from VSM indicate that the saturation magnetization has a maximum when x is ∼1/3. The chemical states of Fe atoms and Zn atoms in zinc ferrites have been measured using XPS and Auger electron spectroscopy (AES). The Fe 2p core-level XPS spectra and Zn L₃M₄₅M₄₅ Auger peaks have been analyzed and the results have been discussed in correlation with the samples’ magnetic properties. These results suggest most of Zn atoms occupy the tetrahedral sites and a small amount of them occupy the octahedral sites.     

Magnetic/structural phase diagram and enhanced giant magnetoresistance in Zn-doped antiperovskite compound Ga1−xZnxCMn3

The structural, magnetic and electrical transport properties of Zn-doped antiperovskite compounds Ga_1−xZn_xCMn₃ (0≤x≤0.30) have been investigated. After partial substitution of Zn for Ga, the Curie temperature increases monotonously and the ground antiferromagnetic (AFM)-ferromagnetic intermediate (FI) phase transition is gradually suppressed. With increasing the doping level x, the saturated magnetizations decreases gradually firstly for x≤0.20, then increases with increasing x. The electrical transport properties of Ga_1−xZn_xCMn₃ are studied at different magnetic fields. Enhanced giant magnetoresistance (GMR) was observed around the AFM-FI transition. With increasing x, the maximal values and peak widths of GMR increase. Particularly, for x=0.20, GMR reaches a maximum value of 75%, spanning a temperature range of 80 K at 50 kOe and displays the behavior of strongly depending on the magnetization history. The possible origins are discussed.     

Superconductivity and magnetism of La2Cu1−xZnxO4+δ chemically oxidized by NaClO

The structural, superconducting and magnetic properties of La₂Cu_1−xZn_xO_4+δ (0≤x≤0.1) chemically oxidized by NaClO at room temperature were studied. All the samples before and after oxidation are single phase with orthorhombic structure, as indicated by their powder X-ray diffraction analysis. The iodometric titration results indicate that Zn-substituted La₂Cu_1−xZn_xO₄ is more favorable for the insertion of the excess oxygen, as compared to the Zn-free La₂CuO₄. The T_c suppression rate resulting from Zn substitution in La₂Cu_1−xZn_xO_4+δ is −12.4 K/%. The effective magnetic moment induced by the non-magnetic Zn ion is the order of one Bohr magneton, which decreases with increasing the Zn concentrations in the range examined. The latter two results are qualitatively well consistent with those obtained in La_2−xSr_xCu_1−yZn_yO₄ with the Sr optimal doping. This reveals that the non-magnetic Zn ions play the same role in both of the La₂Cu_1−xZn_xO_4+δ with the excess oxygen content of about 0.1 and the La_2−xSr_xCu_1−yZn_yO₄ with the Sr optimal doping.     

Magnetic properties and phase diagram of ZnxNi1−xFe2O4: High-temperature series expansions

Using mean field theory and high-temperature series expansions (HTSEs), extrapolated with the Padé approximants method, the effect of Zn doping on magnetic properties of NiFe₂O₄ ferrite spinel has been studied. The nearest neighbour super-exchange interactions for intra-site (J_AA, J_BB) and inter-site (J_AB) of the Zn_xNi_1−xFe₂O₄ ferrites spinels, in the range 0≤x≤1, have been computed using the probability approach, based on Mössbauer data. The paramagnetic Curie-Weiss temperature θ and the Curie temperature T_C are calculated as a function of Zn concentration. The critical exponent γ associated with magnetic susceptibility is calculated. The spin correlation functions intra-plane and inter-plane have been also computed and compared with exchange couplings. The obtained theoretical results are in good agreement with experimental ones obtained by magnetic measurements and Mössbauer spectroscopy.     

Structural, electrical, optical and magnetic properties of Co0.2AlxZn0.8−xO films

Co_0.2Al_xZn_0.8−xO films prepared with different molar ratio of aluminum nitrate to zinc acetate were deposited on substrates by the sol-gel technique. X-ray diffraction, photoluminescence and ferromagnetism measurements were used to characterize the Co_0.2Al_xZn_0.8−xO diluted magnetic semiconductors. The authors found that the intensity of the acceptor-related photoluminescence increased with increasing aluminum concentration and an increase in the number of the acceptor-like defects (zinc vacancies especially) in the Co_0.2Al_xZn_0.8−xO film might lead to the enhancement of the magnetic properties. This implies that controls of the aluminum concentration and the number of the acceptor-like defects are important factors to produce strong ferromagnetism Co_0.2Al_xZn_0.8−xO films prepared by the sol-gel method.     

Enhancement of microstructure and initial permeability due to Cu substitution in Ni0.50−xCuxZn0.50Fe2O4 ferrites

Structural and magnetic properties of Cu substituted Ni_0.50−xCu_xZn_0.50Fe₂O₄ ferrites (where x=0.0-0.25) prepared by an auto combustion method have been investigated. The X-ray diffraction patterns of these compositions confirmed the formation of the single phase spinel structure. The lattice parameter increases with the increase in Cu²⁺ content obeying Vegard's law. The particle size of the starting powder compositions varied from 22 to 72 nm. The theoretical density increases with increase in copper content whereas the Néel temperature decreases. The bulk density, grain size and permeability increases up to a certain level of Cu²⁺ substitution, beyond that all these properties decrease with increase in Cu²⁺ content. The bulk density increases with increase in sintering temperatures up to 1250 °C for the parent composition, while for substituted compositions it increases up to 1200 °C. Due to substitution of Cu²⁺, the real part of the initial permeability increases from 97 to ∼390 for the sample sintered at 1100 °C and from 450 to 920 for the sample sintered at 1300 °C. The ferrites with higher initial permeability have a relatively lower resonance frequency, which obey Snoek's law. The initial permeability strongly depends on average grain size and intragranular porosity. The saturation magnetization, M_s, and the number of Bohr magneton, n(μ_B)_, decreases up to x=0.15 due to the reduction of the A-B interaction in the AB₂O₄ spinel type ferrites. Beyond that value of x, the M_s and the n(μ_B) values are enhanced. The substitution of Cu²⁺ influences the magnetic parameters due to modification of the cation distribution.     

Observation of optical properties related to room-temperature ferromagnetism in co-sputtered Zn1−xCoxO thin films

We report on the analysis of optical transmittance spectra and the resulting ferromagnetic characteristics of sputtered Zn_1−xCo_xO films. Zn_1−xCo_xO films were prepared on (0001)-oriented Al₂O₃ substrates by the radio-frequency (rf) magnetron co-sputtering method. The XRD results showed that the crystallinity of films was properly maintained up to x=0.30 and no second phase peaks were detected up to x=0.40. The transmittance spectra showed both the increase of the absorption band intensity and the red shift of the absorption peak as well as the band edge with increasing x. We have proved experimentally that these changes depend on Co concentration. These optical properties suggest that sp-d exchange interactions and typical d-d transitions become activated with increasing x, which leads to the enhancement of ferromagnetic properties in Zn_1−xCo_xO films as shown in the AGM results. Therefore, it is concluded that the ferromagnetism derives from the substitution of Co²⁺ for Zn²⁺ without changing the wurtzite structure.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.     

Effect of substrate temperature on the morphology, structural and optical properties of Zn1−xCoxO thin films

Zn_1−xCo_xO thin films with c-axis preferred orientation were deposited on sapphire (0 0 0 1) by pulsed laser deposition (PLD) technique at different substrate temperatures in an oxygen-deficient ambient. The effect of substrate temperature on the microstructure, morphology and the optical properties of the Zn_1−xCo_xO thin films was studied by means of X-ray diffraction (XRD), atomic force microscopy (AFM), UV-visible-NIR spectrophotometer, fluorescence spectrophotometer. The results showed that the crystallization of the films was promoted as substrate temperature rose. The structure of the samples was not distorted by the Co incorporating into ZnO lattice. The surface roughness of all samples decreased as substrate temperature increased. The Co concentration in the film was higher than in the target. Emission peak near band edge emission of ZnO from the PL spectra of the all samples was quenched because the dopant complexes acted as non-radiative centers. While three emission bands located at 409 nm (3.03 eV), 496 nm (2.5 eV) and 513 nm (2.4 eV) were, respectively, observed from the PL spectra of the four samples. The three emission bands were in relation to Zn interstitials, Zn vacancies and the complex of V_O and Zn_i (V_OZn_i). The quantity of the Zn interstitials maintained invariable basically, while the quantity of the V_OZn_i slightly decreased as substrate temperature increased.     

The optical properties of CdxZn1−xS thin films on glass substrate prepared by spray pyrolysis method

A series of Cd_xZn_1−xS thin films have been deposited on glass substrates using spray pyrolysis technique. The crystallinity and microstructure of Cd_xZn_1−xS thin films have been investigated by X-ray diffraction (XRD). Based on the results of Hall measurements, the films obtained were an n-type semiconductor. The X-ray data analysis of Cd_xZn_1−xS thin films showed that the grain size of the Cd_xZn_1−xS increased with increase in Cd composition. It is observed that the band gap increases as the Cd composition decreases. The results also showed a blue shift of absorption edge of optical transmission spectra is increases as Zn ratio increases. The effects of Cd composition on the structural and optical properties of Cd_xZn_1−xS thin films were related to their grain size, stress and carrier concentration.     

Optical properties of MgxZn1−xO thin films deposited on silicon and sapphire substrate by rf magnetron sputtering

The index dispersion at UV–VIS range for polycrystalline Mg_xZn_1−xO films on silicon with different Mg concentration was obtained by spectroscopic ellipsometry (SE) method. It decreases with the increase of the Mg content. Above the relative peak wavelength, they are well fitted by the first-order Sellmeier relation. The band gap of films on sapphire of different Mg content was determined from transmission measurements. Photoluminescence (PL) illustrated that for Mg_xZn_1−xO films every PL peak corresponded to a special excitation wavelength. The wavelength of the PL peak was proportional to the special excitation wavelength. A strong peak was obtained in the blue band for the films due to the large amount of oxygen vacancies caused by excess Zn and Mg atoms, while weak peak at ultraviolet band.     

Magnetoresistive properties of Zn1−xCoxFe2O4 ferrites

The magnetic and magnetoresistive properties of spinel-type Zn_1−xCo_xFe₂O₄ (x=0, 0.2 and 0.4) ferrites are extensively investigated in this study. A large negative magnetoresistance (MR) effect is observed in Zn_1−xCo_xFe₂O₄ ferrites of spinel structure. These materials are either ferrimagnetic or paramagnetic at room temperature, and show a spin-(cluster) glass transition at low temperatures, depending on the chemical compositions. The MR curves as a function of magnetic fields, MR(H), are parabolic at all temperatures for paramagnetic polycrystalline ZnFe₂O₄. The MR for ZnFe₂O₄ at 110 K in the presence of 9 T applied magnetic field is 30%. On the other hand, MR(H) are linear for x=0.2 and 0.4 ferrimagnetic Zn_1−xCo_xFe₂O₄ samples up to 9 T. The MR effect is independent of the sintering temperatures, and can be explained with the help of the spin-dependent scattering and the Yafet–Kittel angle of Zn_1−xCo_xFe₂O₄ mixed ferrites.     

Monodispersed nanocrystalline Co1–xZnxFe2O4 particles by forced hydrolysis: Synthesis and characterization

Zinc-substituted cobalt ferrites, Co_1–xZn_xFe₂O₄, were for the first time successfully prepared by forced hydrolysis method. The obtained materials are single phase, monodispersed nanocrystalline with an average grain size of about 3 nm. These materials are superparamagnetic at room temperature and ferrimagnetic at temperature lower than the blocking temperature. When the zinc substitution increases from x=0 to 0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g. The high saturation magnetization of these samples suggests that this method is suitable for preparing high-quality nanocrystalline magnetic ferrites for practical applications.     

Estimating the cation distributions in the spinel ferrites Cu0.5−xNi0.5ZnxFe2O4 (0.0≤x≤0.5)

Ferrite samples of the composition Cu_0.5−xNi_0.5Zn_xFe₂O₄ (0.0≤x≤0.5) were synthesized by chemical co-precipitation. The samples exhibited a single phase cubic spinel structure, and the saturation magnetization of the samples was found to increase with increasing Zn content. Using a quantum mechanical method proposed by our group, the cation distributions in the samples were estimated. Estimated cation distributions obtained by fitting the magnetic moments of the samples were then used to perform Rietveld fitting for X-ray diffraction patterns. The acceptable error parameters in the Rietveld fitting indicate that the estimated cation distributions in the samples are reasonable.     

Preparation, characterization and magnetic properties of the doped barium hexaferrites BaFe12−2xCox/2Znx/2SnxO19, x=0.0-2.0

A series of powders of M-typed barium hexaferrites doped with Co, Zn and Sn of general formula BaFe_12-2xCo_x/2Zn_x/2Sn_xO₁₉ (x=0-2.0) were prepared by the co-precipitation/molten salt method. The structures, particle morphology and magnetic properties of the products were characterized by X-ray powder diffraction, vibrating sample magnetometer and ESEM/EDX. The results show that the crystallinity of the samples decreases with increase in the doping amount x. When x is less than 0.6, it is possible to obtain perfectly crystallized hexagonal BaFe_12-2xCo_x/2Zn_x/2Sn_xO₁₉, where the diameters of the particles are around 500 nm. The saturation magnetization of pure barium ferrite BaFe₁₂O₁₉ produced with this method is 71.9 A m² kg⁻¹ at room temperature and the intrinsic coercivity (H_c) is 367.8 kA m⁻¹. The doped barium hexaferrite powder obtained when x is between 0.3 and 0.4 exhibits high saturation magnetization and a temperature dependence of coercivity close to zero.     

Transport properties and conduction mechanisms in CuFe2O4 and Cu1−xZnxGa0.3Fe1.7O4 compounds

Single-phase structure of CuFe₂O₄ and Cu_1−xZn_xGa_0.3Fe_1.7O₄; with (0.0≤x≤0.5) are synthesized. Electrical conductivity measurements as a function of temperature are carried out in the frequency range (10²-10⁵ Hz) for the prepared samples. The obtained results of these materials reveal a metallic-like behavior in the low range of frequency. At high frequency regime metallic-to-semiconductor transition has been observed as the compositional parameter x increases. Metallic-like behavior is accompanied with samples having low Zn content, where cation-cation [Cu-Cu] interaction is major at the octahedral B-sites and semiconductor behavior is associated with compounds having high Zn content, where cation-anion-cation [Fe-O-Fe] interaction is most predominant at B-sites in these spinel oxides. All studied compositions exhibit a transition with change in the slope of conductivity versus temperature curve. This transition temperature is found to decrease linearly with increasing Zn concentration x. The relation of the universal exponent s with temperature indicates the presence of two hopping conduction mechanisms; the correlated barrier hopping CBH at low Zn content x≤0.2 and small polaron (SP) at Zn content x≥0.3.     

Growth of cubic MgxZn1−xO alloy films by electron beam evaporation

We report the growth of cubic Mg_xZn_1−xO alloy thin films on quartz by electron beam evaporation. It can be found that all the samples have sharp absorption edges by the absorption measurements. X-ray diffraction measurements indicate the Mg_xZn_1−xO films are cubic phase with preferred orientation along the (1 1 1) direction. Energy dispersive spectrometry (EDS) demonstrates that the Mg concentration in Mg_xZn_1−xO films is much higher than the ceramic target used, and the composition can be tuned in a small scope by varying the substrate temperature and the beam electric current. The reasons of this phenomenon are also discussed.     

Ferromagnetism in diluted magnetic Zn-Co-doped CeO2−δ

Several oxides doped with transition metals can be used in spintronics devices due to their conductive and magnetic properties at room temperature. In this work, samples of Ce_1−2xZn_xCo_xO_2−δ were obtained by an alternative sol–gel proteic process for x=0.01, 0.05 and 0.1. The structural properties of samples were analyzed by XRD and Raman spectroscopy. Magnetization measurements revealed a ferromagnetic behavior at room temperature probably induced by oxygen vacancies.