OSL and TL in TLD-100 following alpha and beta irradiation: Application to mixed-field radiation dosimetry

The optically stimulated luminescence (OSL) of LiF:Mg,Ti (TLD-100) following irradiation by beta and alpha particles was investigated by measurement of the excitation and emission spectra of OSL and comparison with thermoluminescence (TL) characteristics. The OSL excitation spectra of all the samples following both beta and alpha irradiation are very similar.Identical emission bands with very similar relative intensities following both beta irradiation and alpha particle irradiation have been recorded in the OSL induced in nominally pure LiF mono and TLD-100 polycrystals. The identical excitation and emission bands in the doped and pure crystals are strong evidence indicating that the observed OSL is due to an intrinsic trapping structure. The OSL has indeed been previously attributed to F₂ centers and F₃⁺ centers.The preferential excitation of OSL compared to TL following high ionisation density (HID) alpha irradiation is naturally explained via the identification of OSL with the “two-hit” F₂ or F₃⁺ center, whereas the major component of composite TL glow peak 5 is believed to arise from a “one-hit” complex defect. This discovery allows near-total discrimination between HID radiation and low ionisation density (LID) radiation and may have significant potential in mixed-field radiation dosimetry.     

Investigation of defect centres responsible for TL/OSL in MgAl2O4:Tb

Magnesium aluminate doped with Tb³⁺ (MgAl₂O₄:Tb³⁺) was prepared by combustion synthesis. Three thermoluminsence (TL) peaks at 120, 220 and 340 °C were observed. PL and TL emission spectrum shows that Tb³⁺ acts as the luminescent centre. Optically stimulated luminescence (OSL) was observed when stimulated by 470 nm blue light.Electron spin resonance (ESR) studies were carried out to identify the defect centres responsible for the TL and OSL processes in MgAl₂O₄:Tb³⁺. Two defect centres were identified in irradiated MgAl₂O₄:Tb³⁺ phosphor by ESR measurements which was carried out at room temperature and these were assigned to V and F⁺ centres. V centre (hole centre) is correlated to 120 and 220 °C TL peaks and F⁺ centre (electron centre), which acts as a recombination centre is correlated to 120, 220 and 340 °C.     

α-Al2O3:C晶体的热释光和光释光特性

以高纯α-Al₂O₃和石墨为原料,采用温梯法生长了α-Al₂O₃：C晶体,使用Ris TL/OSL-DA-15型热释光和光释光仪研究了其热释光和光释光特性.α-Al₂O₃：C晶体在462K附近有单一热释光峰,发射波长位于410nm.随着辐照剂量的增加,热释光强度逐渐增强,462K的热释光特征峰位置保持不变.α-Al₂O₃：C晶体的 关键词： 2O₃：C')" href="#">α-Al₂O₃：C 热释光 光释光     

The use of the TL and OSL phenomena for determination of absorbed dose rates of 90Sr + 90Y sources by a postal method

International recommendations establish that ⁹⁰Sr + ⁹⁰Y clinical applicators have to be calibrated in order to determine the absorbed dose rates in the case of the sources that do not have original calibration certificates, or to update the absorbed dose rates presented in the source certificates. Following these recommendations, a postal dosimetric system was developed to calibrate clinical applicators using two luminescent techniques: thermoluminescence (TL) and optically stimulated luminescence (OSL). In this work, Al₂O₃:C commercial detectors were characterized and their TL and OSL responses were analyzed. The results showed the efficiency and the optimal behavior of this material in beta radiation beams. After characterization, the system was sent to the Federal University of Sergipe (UFS), Brazil, for calibration of five ⁹⁰Sr + ⁹⁰Y clinical applicators, where the detectors were irradiated and returned to IPEN, for their evaluation and determination of the absorbed dose rates. A comparison between these absorbed dose rates and those adopted by the UFS as original was made; the differences obtained were within those of other studies, and they demonstrated the usefulness of the system.     

Study of the luminescent behavior of Spectrolite + Teflon pellets in 90Sr + 90Y beams

The Spectrolite, from the silicate family, a variety of Labradorite, was already studied in relation to its thermoluminescence (TL) and optically stimulated luminescence (OSL) responses, in high-dose gamma radiation fields; the results indicated their good application as gamma radiation detectors. In the present work, the analyses performed to investigate powdered Spectrolite are presented, by means of the XRD, SEM and EDX techniques. The luminescent behavior of Spectrolite + Teflon samples, in the concentration of 1:1, was studied in beta radiation beams (⁹⁰Sr + ⁹⁰Y), using the luminescent phenomena of TL and OSL. The results showed adequate TL and OSL reproducibility of the samples; the dose–response curves for both techniques presented a linear behavior in a range from 0.5 Gy to 1 kGy, and the fading showed that after 150 h there were 46.7% and 31.6% of the remaining signal of samples for TL and OSL responses, respectively. Therefore, the Spectrolite + Teflon pellets may be used in beta radiation dosimetry.     

Energy levels in YPO4:Ce3+,Sm3+ studied by thermally and optically stimulated luminescence

Energy-resolved optically stimulated luminescence (OSL) spectra and thermoluminescence (TL) glow curves of a powder sample of YPO₄:Ce³⁺,Sm³⁺ were measured to investigate the nature of the trapping centre and to locate its energy level relative to the valence and conduction bands of the YPO₄ host. The high-temperature glow peak could unequivocally be assigned to Sm²⁺ (thus Sm³⁺ acts as an electron trap). The trap depth of this centre, as derived from the OSL excitation spectra, is in good agreement with the Dorenbos model prediction. The OSL excitation spectra also reveal excited states of Sm²⁺ well below the conduction band. These excited states produce a broadening of the high-temperature TL glow peak and also cause the activation energy determined by the Hoogenstraten method to underestimate the trap depth.     

Nanostructured layers of anion-defective gamma–alumina – New perspective TL and OSL materials for skin dosimetry. Preliminary results

Thin- layer material based on nanostructured Al₂O₃ of the surface density 5 mg/cm² was obtained. The material is characterized by high OSL and TL yields comparable with those for TLD-500 which is one of the leaders among the TL and OSL detectors. The dose response, fading and dependence of TL yield on heating rate was studied. It is established that high luminescence yield of the samples under study correlates with the content of anion vacancies and γ-phase of Al₂O₃. The data for time-resolved luminescent spectroscopy are presented, which evidence for possible correlation between high TL and OSL activity and the F-type centers. It is noted that the material needs to be modified for successful use in dosimetry. In addition further studies to decrease the contribution of unstable (at 300 К) components to OSL and TL yields are required.     

Comparative investigations of TL and OSL in KCI:Eu2+ crystals irradiated with UV and X-rays

Abstract

We present thermoluminescence (TL) glow curves and optical stimulated luminescence (OSL) response from both KCl:Eu²⁺ crystals irradiated with soft X-rays (20 KV, 80 μA) and ultraviolet light (230 nm). Two situations take place. First, we observed that for long time F-light bleaching (560 nm) the typical TL glow curve of X-rays irradiated KCl:Eu²⁺ resembles the TL glow curve of UV-irradiated samples. Second, along with OSL measurements, we have performed a thermal bleaching and we have addressed F and F_z participation in OSL. These results provide us a supportable correlation between F and F_z as responsible centers for OSL and TL processes.     

Optically stimulated luminescence in doped K3Na(SO4)2 phosphors

Optically stimulated luminescence (OSL) in Cu and Eu doped K₃Na(SO₄)₂ is reported for the first time. The Cu-doped sample shows OSL sensitivity which gets enhanced by co-doping with Mg²⁺ ions. The Cu-doped and quenched sample shows better sensitivity which is almost double than that of the slowly cooled sample, whereas the sensitivity of Mg co-doped sample remains nearly same irrespective of the thermal treatment. The Cu-doped sample shows TL peak around 200 °C and moderate OSL sensitivity. Doping of Mg shifts the TL peak to around 160 °C and is correlated with good OSL sensitivity. Eu-doped sample does not show OSL sensitivity. However, relatively good OSL sensitivity is observed in Aluminium co-doped and slowly cooled sample, which is about 15% of the commercial Al₂O₃:C(Landuer Inc.). A near fully optically sensitive TL peak around 155 °C is observed. The dose response is linear and practically no OSL fading is observed in first five days of storage in slowly cooled sample. This study on conventional sulphate-based TL phosphors will be useful in developing OSL phosphors for radiation dosimetry.     

TL and OSL dosimetric properties of Opal gemstone for gamma radiation dosimetry

In this work, the response of the natural material Opal was studied in relation to its thermoluminescence (TL) and optically stimulated luminescence (OSL), after exposure to the gamma radiation of a ⁶⁰Co source. The structure of the powdered Opal was verified using the X-ray diffraction, scanning electronic microscopy and energy-dispersive X-ray spectroscopy techniques. The material, in its stone form, was turned into powder and mixed to Teflon (also in powder) in three different concentrations, and then pellets were manufactured. The aim of this work was to evaluate the response of these pellets in high-doses of gamma radiation beams, and to observe their possible application as dosimeters, using the TL and OSL techniques. The dosimetric properties of the samples were analyzed by means of different tests, as: TL emission curves and OSL signal decay curves, reproducibility of TL and OSL response, minimum detectable dose, TL and OSL dose–response curves (5 Gy–10 kGy), and fading. The results obtained in this work, for the TL and OSL phenomena, demonstrated that the pellets of Opal + Teflon present an adequate performance e possibility of use as dosimeters in beams of high-dose gamma radiation.     

Optically stimulated luminescence (OSL) and thermally assisted OSL in Eu2+ – Doped BaSO4 phosphor

BaSO₄:Eu²⁺ phosphor has been investigated for its photoluminescence (PL), thermoluminescence (TL), TL kinetics, optically stimulated luminescence (OSL) and thermally assisted OSL (TA-OSL) response. PL spectra showed the characteristic emission of Eu²⁺ ion at 375 nm when excited by 320 nm. The luminescence lifetime has been measured as 40 and 628 μs of fast and slow components respectively. The TL parameters such as trap depth (E), frequency factor (s) and the order of kinetics (b) are determined. The phosphor is found to be 6 and 4 times more sensitive than CaSO₄:Dy and α-Al₂O₃:C, respectively, in TL mode. However, its OSL sensitivity is 75% of α-Al₂O₃:C. It is found to possess three OSL components having photoionization cross-sections of 1.4 × 10⁻¹⁷, 1.2 × 10⁻¹⁸ and 5.2 × 10⁻¹⁹ cm² respectively. The temperature dependence of OSL studies showed that integrated TA-OSL signal increases with stimulation temperature between 50 and 250 °C, while between 260 and 450 °C the signal intensity decreases. This behavior is interpreted to arise from competing effects of thermal assistance (activation energy E_A = 0.063 ± 0.0012 eV) and depletion of trapped charges. This increase of OSL at elevated temperature can be employed for enhancing the sensitivity of phosphor for radiation dosimetry.     

Correlation between TL and OSL signals in KMgF3:Ce3+: Bleaching study of individual glow-peaks

KMgF₃:Ce³⁺ is an ultra sensitive Thermoluminescence (TL) material with a complex TL and OSL glow-curve structure. The aim of the present work is to attempt a one-to-one correspondence between specific TL glow-peaks and OSL components in KMgF₃:Ce³⁺. The correlation study involves the deconvolution of the TL curves and the estimation of the bleaching decay constants for individual glow-peaks followed by the deconvolution of the LM-OSL curve using the estimated decay constants. It was found that the bleaching of each individual glow-peak takes place in three different rates; namely in a fast, medium and slow rate.     

In-Vacuo thermal processing of α-Al2O3 single crystals in boron ambience and its implication on TL & OSL response

Single crystals of α-Al₂O₃ (10×10 mm², 0.4 mm thick) were annealed in vacuum at about 1500 °C in the ambience of boron. The OA studies on these samples showed bands at 203, 232 and 258 nm signifying that such a treatment leads to the formation of F and F⁺ centers in significant concentrations, these bands, however, were not found in the Al₂O₃ crystals processed in the similar manner in the absence of boron. The Al₂O₃:B samples were irradiated to different absorbed doses of ⁹⁰Sr/⁹⁰Y β-source and the continuous wave OSL (CW-OSL) was recorded on the samples using 470 nm blue light stimulation. These samples have shown a linear TL and CW-OSL response in the dose range of 20 mGy to 15 Gy. The minimum detectable dose, corresponding to 3σ limit of the variation of the output of the unirradiated dosimeters, was found to be 100 μGy. Irradiated samples stored in dark at room temperature for a period of two months show negligible fading. The TL and OSL sensitivities of the samples were found to be strongly dependent on process temperature and time. The TL response is marked by the absence of low temperature peak (<100 °C), unlike the case of α-Al₂O₃:C, implying that the boron doping does not lead to formation of shallow traps. The Al₂O₃:B samples show faster photoionisation cross-section as compared to α-Al₂O₃:C. This approach of processing of single crystal Al₂O₃ in the boron ambience thus represents a potential way of introducing dosimetrically pertinent defects in Al₂O₃ single crystals.     

Features of OSL and TL properties of anion-defective corundum crystals exposed to thermo-optical treatment

The results of systematic investigation of the mechanisms and role of phototransfer in TL and OSL processes in α-Al₂O_3−δ crystals under controlled filling of the main and deep traps depleted at 450 and 720 K, respectively, are presented.Optical depletion spectra of the main and deep traps were measured and compared. It was found that green light stimulation only depletes the main trap, while blue light depletes both the main and deep traps. Optical depletion of the deep trap results in phototransfer of charges that can be realized by 2 mechanisms: either through the main trap to recombination centers or directly to the latter. However, the dominant contribution to the OSL signal is provided by phototransfer through the main trap. It is also found that UV emission at 3.7 eV dominates over F-emission at 3.0 eV in the phototransferred TL spectrum. It is assumed that this UV emission is not related to the F⁺ centers.     

Correlation of optically and thermally stimulated luminescence of natural fluorite pellets

Natural fluorite (CaF₂), a dosimetric material of large usage, presents Thermoluminescence (TL) and Optically Stimulated Luminescence (OSL). This study examined the behavior of TL and OSL (stimulated with Blue LEDs) signals from the Brazilian natural fluorite pellets with NaCl as binding agent, as well as their correlations, in order to study and optimize the dosimetric process with this material. A series of experiments were conducted, basically with thermal treatments before OSL acquisition, and optical bleaching before TL readout. The role of NaCl in the TL and OSL emission was investigated. It was observed that natural CaF₂ TL signal is still ample to be used in dosimetric applications, as dose re-assessment in personal dosimetry after an OSL measurement. Also it was verified that the fluorite OSL signal is extinguished by a 350 °C heating and that NaCl has no contribution to the stable part of the OSL signal.     

Role of Ti in the luminescence process of Al2O3:Si,Ti

Al₂O₃:Si,Ti, prepared under oxidizing condition at high temperature, gives PL emission around 430 nm when excited with 240 nm. The Al₂O₃:C, TL/OSL phosphor, also shows emission around 430 nm, which corresponds to characteristic emission of F-center. Thus, to identify the exact nature of luminescent center in Al₂O₃:Si,Ti, fluorescence lifetime measurement studies were carried out along with the PL,TL and OSL studies. The PL and TL in Al₂O₃:Si,Ti show emission around 430 nm and the time-resolved fluorescence studies show lifetime of about 43 μs for the 430 nm emission, which is much smaller than the reported lifetime of ∼35 ms for the 430 nm emission (F-center emission) in Al₂O₃:C phosphor. Therefore, the emission observed in Al₂O₃:Si,Ti phosphor was assigned to Ti⁴⁺ charge transfer transition. Fluorescence studies of Al₂O₃:Si,Ti do not show any traces of F and F⁺ centers. Also, Ti⁴⁺ does not show any change in the charge state after gamma-irradiation. On the basis of the above studies, a mechanism for TSL/OSL process in Al₂O₃:Si,Ti is proposed.     

Afterglow mechanism and thermoluminescence of red-emitting CaS:Eu,Pr phosphor with incorporated Li ion upon visible light irradiation

This paper reports on the afterglow mechanism and thermoluminescence (TL) of a red-emitting CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion upon irradiation by visible light (D₆₅ lamp). In the TL glow curve of the CaS:Eu²⁺,Pr³⁺ phosphor, a TL peak was observed near 120 °C. The luminescence center of the CaS:Eu²⁺,Pr³⁺ phosphor was the Eu²⁺ ion and the trap depth of the CaS:Eu²⁺,Pr³⁺ phosphor with the cation vacancy (Trap 1) which formed by incorporation of the Pr³⁺ ion was 0.202 eV. A cation vacancy (Trap 2) was formed by incorporation of the Li⁺ ion in the CaS:Eu²⁺,Pr³⁺ phosphor. In the TL glow curve of the CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion, two TL peaks were observed near 120 and 200 °C. The TL luminance of the CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion increased with an increase in the initial Li/Ca atomic ratio. The two TL peaks moved to the high-temperature side with an increase in heating rate. The cation vacancy (Trap 2) calculated from the Hoogenstraaten method was 0.118 eV. The afterglow time of the CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion was prolonged by generation of a shallow trap.     

Thermoluminescence and optically stimulated luminescence in various phases of doped Na2SO4

The dependence of optically stimulated luminescence (OSL) and thermoluminescence (TL) response due to crystal phase in Cu and Cu,Mg-doped Na₂SO₄ was studied. Study shows that the slowly cooled samples which crystallize in phase V show good OSL sensitivity whereas the quenched samples of Na₂SO₄ which crystallize in phase III irrespective of doping show no OSL sensitivity. However, during storage when phase III samples get converted to phase V, samples show OSL sensitivity comparable to freshly prepared samples in phase V. Hence, it is observed that TL–OSL properties of doped Na₂SO₄ are phase dependent .This study will be helpful in developing OSL phosphors in which phase plays an important role in deciding the desired properties.     

Growth of α-Al2O3:C crystal with highly sensitive optically stimulated luminescence

In this work, an α-Al₂O₃:C crystal was directly grown by the temperature gradient technique (TGT) using Al₂O₃ and graphite powders as the raw materials. The optical, optically stimulated luminescence (OSL) properties and dosimetric characteristics of as-grown crystal were investigated. As-grown α-Al₂O₃:C crystal shows strong absorption band at 205, 230 and 256 nm. Three-dimensional thermoluminescence (TL) emission spectrum of the crystal shows a single emission peak at ∼415 nm. The OSL decay curve can be fitted to two exponentials, the faster component and the slower component. The OSL response of the crystal shows a linear-sublinear-saturation characteristic. As-grown α-Al₂O₃:C crystal shows excellent linearity in the dose range from 5×10⁻⁶ to 50 Gy. For doses higher than the saturation dose (100 Gy), the OSL sensitivity decreases as the dose increases.     

The response of thermally and optically stimulated luminescence from Al2O3:C to high-energy heavy charged particles

The thermoluminescence (TL) and optically stimulated luminescence (OSL) response of Al₂O₃ dosimeters to high-energy heavy charged particles (HCP) has been studied using the heavy ion medical accelarator at Chiba, Japan. The samples were Al₂O₃ single-crystal chips, of the type usually known as TLD-500, and Luxel^TM dosimeters (Al₂O₃:C powder in plastic) from Landauer Inc. The samples were exposed to ⁴He (150 MeV/u), ¹²C (400 MeV/u), ²⁸Si (490 MeV/u) and ⁵⁶Fe (500 MeV/u) ions, with linear energy transfer values covering the range from 2.26 to 189 keV/μm in water and doses from 1 to 100 mGy (to water). A ⁹⁰Sr/⁹⁰Y beta source, calibrated against a ⁶⁰Co secondary standard, was used for calibration purposes. For OSL, we used both continuous-wave OSL measurements (CW-OSL, using green light stimulation at 525 nm) and pulsed OSL measurements (POSL, using 532 nm stimulation from a Nd:YAG Q-switched laser). The efficiencies (η_HCP,γ) of the different HCPs at producing OSL or TL were observed to depend not only upon the linear energy transfer (LET) of the HCP, but also upon the sample type (single crystal chip or Luxel^TM) and the luminescence method used to define the signal—i.e. TL, CW-OSL initial intensity, CW-OSL total area, or POSL. Observed changes in shape of the decay curve lead to potential methods for extracting LET information of unknown radiation fields. A discussion of the results is given, including the potential use of OSL from Al₂O₃ in the areas of space radiation dosimetry and radiation oncology.