VUV spectroscopic properties of Ce and Pr-doped AREP2O7-type alkali rare earth diphosphates (A=Na, K, Rb, Cs; RE=Y, Lu)

Spectroscopic properties of Ce³⁺ and Pr³⁺-doped AREP₂O₇-type alkali rare earth diphosphates (A=Na, K, Rb, Cs; RE=Y, Lu) have been investigated using VUV spectroscopy technique. Ce³⁺-doped samples show typical Ce³⁺ emission in the range of 325-450 nm. The strong host absorption band starting at around 160 nm indicates that the optical band gap of AREP₂O₇ hosts is at least 7.7 eV, and the host→Ce³⁺ energy transfer process is rather efficient. However, AREP₂O₇:Pr³⁺ samples show less efficient host→Pr³⁺ energy transfer. The direct Pr³⁺ 4f²→4f¹5d¹ excitation, which are 12160±640 cm⁻¹ higher respect to that of Ce³⁺, leads to strong 4f¹5d¹→4f² emission bands in the range of 230-325 nm but no obvious 4f²→4f² emission lines.     

Characterization of the VUV excitation spectrum of BaZr(BO3)2:Eu

The excitation spectra of M (M=Si⁴⁺, Ti⁴⁺) and Eu³⁺ co-doped BaZr(BO₃)₂, BaZrO₃:Eu and La₂Zr₂O₇:Eu in the vacuum ultraviolet (VUV) regions of 110-300 nm are investigated and the host-lattice absorption are characterized. The result indicated that BaZr(BO₃)₂:Eu³⁺ phosphor has a strong absorption under the VUV excitation, and in the host-lattice excitation, the strong band at 130-160 nm could be due to the BO₃ atomic groups; the band at 160-180 nm is related to the excitation of Ba-O; 180-200 nm corresponds to the charge transfer (CT) transition of Zr-O. The band at 200-235 nm due to the CT band of Eu³⁺-O²⁻ and a bond valence study explained the observed weak CT band of Eu³⁺-O²⁻ in the excitation spectra of BaZr(BO₃)₂:Eu³⁺. The emission results show that Si⁴⁺ can sensitize luminescence in the host of BaZr(BO₃)₂:Eu but Ti⁴⁺ has no improvement effect on luminescence.     

The influence of Pr co-doping on the luminescent properties of Lu2O3:5 mol% Eu films

Uniform and crack free polycrystalline lutetium oxide (Lu₂O₃:(Eu,Pr)) films were fabricated by Pechini sol-gel method combined with the spin-coating technique. X-ray diffraction (XRD) and atomic force microscope (AFM) characterizations indicated that the obtained film was composed of polycrystalline cubic Lu₂O₃ phase with an average grain size around 30 nm. The photoluminescence(PL) spectra and decay performances of the Lu₂O₃:5 mol% Eu films co-doped by 0-0.5 mol% Pr³⁺ with different concentrations were characterized. It was found that the afterglow was reduced obviously due to the introduction of 0-0.5 mol% Pr³⁺ in the Lu₂O₃:5 mol% Eu films coupled by decrease in the emission intensity at 612 nm. The mechanism of afterglow diminishing was discussed based on the thermoluminescence measurements.     

Native defects and Pr impurities in orthorhombic CaTiO3 by first-principles calculations

Formation energies of native defects and Pr impurities in orthorhombic CaTiO₃ are explored using the first-principles calculations. The Ca vacancy (V_Ca), Ti vacancy (V_Ti) and Ca antisite (Ca_Ti) are found to be energetically preferable. The Ti antisite (Ti_Ca) and O vacancy (V_O) are not energetically favorable in the wide range of Fermi level. In Pr-doped CaTiO₃, Pr substituting for Ca (Pr_Ca) is likely to form under condition A in which CaTiO₃ is in equilibrium with CaO and O₂. Under condition B (TiO₂, CaTiO₃ and O₂ are in equilibrium), Pr_Ti defect is energetically preferable depending on the Fermi levels. Several native defects and the two sites of Pr impurities in CaTiO₃ are coincided with several different defects in Pr-doped CaTiO₃ reported in the literature. Based on the present calculations, we can elucidate that the Ca deficiency design of the traditional formula Ca_1−xV_Ca(x/2)Pr_xTiO₃ is not the best for efficient red photoluminescence, which is realized via the experimental measurements.     

Spectral-kinetic characteristics of Pr luminescence in LiLuF4 host upon excitation in the UV-VUV range

Spectral-kinetic study of Pr³⁺ luminescence has been performed for LiLuF₄:Pr(0.1 mol%) single crystal upon the excitation within 5-12 eV range at T=8 K. The fine-structure of Pr³⁺ 4f ²→4f 5d excitation spectra is shown for LiLuF₄:Pr(0.1 mol%) to be affected by the efficient absorption transitions of Pr³⁺ ions into 4f 5d involving 4f ¹ core in the ground state. Favourable conditions have been revealed in LiLuF₄:Pr(0.1 mol%) for the transformation of UV-VUV excitation quanta into the visible range. Lightly doped LiLuF₄:Pr crystals are considered as the promising luminescent materials possessing the efficient Pr³⁺³P₀ visible emission upon UV-VUV excitation. The mechanism of energy transfer between Lu³⁺ host ion and Pr³⁺ impurity is discussed.     

Doping effects of Nb5+ on red long afterglow phosphor CaTiO3:Pr3+

A series of Nb5+ codoped red long afterglow phosphors CaTi1 xNbxO3:Pr03.+002 (0 ≤ x ≤ 0.05) is prepared by a solid state reaction method. Their photoluminescence, phosphorescence and thermoluminescence are investigated. The results indicate that codoping Nb5+ can improve the photoluminescence and phosphorescence property of CaTiO3:Pr3+ significantly. When 3-mol% Nb5+ is codoped, the emission intensity of CaTiO3:Pr3+ is enhanced twice, while the afterglow time is extended from 10 min to about 40 min. Thermoluminescence results reveal that the trapping level of CaTiO3:Pr3+ is reduced from 0.82 eV to 0.62 eV by codoping Nb5+. The effect of Nb5+ doping on enhancing the photoluminescence intensity and afterglow time of CaTiO3:Pr3+ is discussed.     

Luminescence from the Pr 4f5d and S0 states in LiLaP4O12

The photoluminescence and excitation spectra of Pr³⁺ activated LiLaP₄O₁₂ has been investigated in the 10-300 K temperature region. At all temperatures, the luminescence consists of optical transitions emanating from both the Pr³⁺ 4f¹5d¹ and the ¹S₀ states. However, at low temperatures the emission spectrum is dominated by the intraconfiguration emission transitions emanating from the Pr³⁺¹S₀ state. With increasing temperature, there is an exchange of intensity between the two emitting states; emission transitions from the ¹S₀ state exhibit strong intensity quenching while the 4f¹5d¹→4f² emission transitions reveal intensity gain. These results are explained on the basis of thermal population of the 4f¹5d¹ state by the ¹S₀ state. The energy barrier of 0.05 eV (403 cm⁻¹) for the nonradiative process is determined from the temperature dependence of the ¹S₀ lifetime.     

Spectral and kinetic characteristics of trivalent praseodymium in LaF3-LiF and SrAl12O19

Recent data on cascade transitions in the 4f shell of the Pr³⁺ ion in various matrices are analyzed. Spectral and kinetic characteristics of LaF₃-LiF:Pr and SrAl₁₂O₁₉:Pr phosphors, which show photon cascade emission, were investigated. The emission intensities in the first (¹ S→¹ I ₆ transitions) and the second (transitions from the ³ P ₀ level to the ³ H and ³ F multiplets) cascade stages were measured and the temperature dependences of the intensities of the main emission lines and their kinetic characteristics were determined. The following parameters of SrAl₁₂O₁₉:Pr were found: the band gap width (7.5 eV), the energy gap between the ¹ S ₀, 4f and 5d levels (0.24 eV), and the characteristics of the 4f→5d band (6.0–7.5 eV) of the Pr³⁺ luminescence excitation. It is shown that the LaF₃-LiF:Pr compound has a number of specific features in comparison with other Pr³⁺-doped phosphors.     

Synthesis and characterization of BaAl2O4:Eu co-doped with different rare earth ions

Combustion method was used in this study to prepare BaAl₂O₄:Eu²⁺ phosphors co-doped with different trivalent rare-earths (Re³⁺=Dy³⁺, Nd³⁺, Gd³⁺, Sm³⁺, Ce³⁺, Er³⁺, Pr³⁺ and Tb³⁺) ions at an initiating temperature of 600 °C. The phosphors were annealed at 1000 °C for 3 h. As confirmed from the X-ray diffraction (XRD) data, both as prepared and post annealed samples crystallized in the well known hexagonal structure of BaAl₂O₄. All samples exhibited bluish-green emission associated with the 4f⁶5d¹→4f⁷ transitions of Eu²⁺ at ∼500 nm. Although the highest intensity was observed from Er³⁺ co-doping, the longest afterglow (due to trapping and detrapping of charge carriers) was observed from Nd³⁺ followed by Dy³⁺ co-doping. The traps responsible for the long afterglow were studied using thermoluminescence (TL) spectroscopy.     

Effect of interface states associated with transitional nanophase precipitates in the enhancement of red emission from SrAl12O19:Pr by Ti incorporation

SrAl₁₂O₁₉:Pr³⁺, Ti⁴⁺ phosphor suitable for field emission displays is prepared by the wet chemical gel-carbonate method and the mechanism of enhancement in red photoluminescence (PL) intensity with Ti⁴⁺ therein has been investigated. The PL spectra of Pr³⁺ show both ¹D₂-³H₄ and ³P₀-³H₆ emission in the red region with very weak intensity when excited at 355 nm. The emission intensity has increased by about 100 times at room temperature in the compositional range SrAl_12−xTi_xO_19+x/2:Pr³⁺, with 0.1≤x≤0.3 in comparison to Ti-free SrAl₁₂O₁₉:Pr³⁺. TEM investigations show the presence of exsolved nanophase of SrAl₈Ti₃O₁₉, the precipitation of which is preceded by the presence of defect centers at the interfacial regions between the semicoherent transient phase and the parent SrAl₁₂O₁₉ matrix. The presence of transitional nanophase and the associated defects modify the excitation-emission process by way of formation of electronic sub-levels at lower energy (3.5 eV) than the band gap of SrAl₁₂O₁₉ (∼7 eV) followed by non-resonance energy transfer to Pr³⁺ level, leading to magnetic-dipole related red emission with enhanced intensity. The PL intensity of Pr³⁺ decreases at high Ti⁴⁺ concentrations (x>0.3) due to higher extent of segregation of non-emissive SrAl₈Ti₃O₁₉:Pr³⁺ phase.     

Phosphorescent and thermoluminescent properties of SrAl2O4:Eu,Dy phosphors prepared by solid state reaction method

Long persistent SrAl₂O₄:Eu²⁺ phosphors co-doped with Dy³⁺ were prepared by the solid state reaction method. The main diffraction peaks of the monoclinic structure of SrAl₂O₄ were observed in all the samples. The broad band emission spectra at 497 nm for SrAl₂O₄:Eu²⁺, Dy³⁺ were observed and the emission is attributed to the 4f⁶5d¹ to 4f⁷ transition of Eu²⁺ ions. The samples annealed at 1100–1200 °C showed similar broad TL glow curves centered at 120 °C. The similar TL glow curves suggest that the traps responsible for them are similar. The long afterglow displayed by the phosphors annealed at different temperatures, may be attributed to the Dy³⁺ ions acting as the hole trap levels, which play an important role in prolonging the duration of luminescence.     

Energy transfer in LaMgB5O10:Pr,Mn under VUV excitation

Luminescent properties of Pr³⁺ or Mn²⁺ singly doped and Pr³⁺, Mn²⁺ co-doped LaMgB₅O₁₀ are investigated by synchrotron radiation VUV light. When LaMgB₅O₁₀:Pr³⁺ is excited at185 nm, the photon cascade emission between 4f levels of Pr³⁺ is observed. In the excitation spectra of LaMgB₅O₁₀:Mn²⁺ monitoring the 615 nm emission of Mn²⁺, several excitation bands in a spectral range from 330 to 580 nm are recorded, among which the most intense band is centered at 412 nm (⁶A_1g→⁴E_g-⁴A_1g). This band has considerable spectra overlap with the 410 nm emission (¹S₀→¹I₆) of Pr³⁺, which is favorable for energy transfer from Pr³⁺ to Mn²⁺. Such energy transfer is observed in the co-doped sample, converting the violet emission (410 nm) of Pr³⁺ into the red emission (615 nm) of Mn²⁺. The concentration dependence of transfer efficiency is also investigated.     

Surface chemical changes of CaTiO3:Pr upon electron beam irradiation

Surface chemical changes of CaTiO₃:Pr³⁺ phosphor material and their effect on the red emission intensity of the ¹D₂→³H₄ transition of Pr³⁺, upon electron beam irradiation are presented. Red emission at 613 nm was obtained upon probing the surface with a 2 keV electron beam. The surface chemical changes and Pr³⁺ red emission were monitored using an Auger Electron Spectroscopy (AES) and Cathodoluminescence (CL) spectrometer, respectively. The CL intensity decreased with a decrease in O on the surface at 1×10⁻⁸ Torr base pressure and decreased with an increase in O on the surface at 1×10⁻⁶ Torr O₂. The X-ray Photoelectron Spectroscopy (XPS) revealed that CL degradation at 1×10⁻⁶ Torr O₂ is due to the formation of CaO and CaO_x as well as TiO₂/Ti₂O₃ non-luminescent species on the surface.     

Site selective 4f5d spectroscopy of CaF2 : Pr

Spectroscopic investigations were performed on a single crystal of CaF₂ doped with 0.05% Pr³⁺. Three different Pr³⁺ sites with different luminescent properties were identified. The 4f² →4f¹5d¹ excitation spectrum of the first site has a sharp maximum at 221.3 nm. Excitation in the 4f5d bands of this site yields strong 4f5d emissions in the UV/VIS part of the spectrum and also weaker intraconfigurational 4f² emissions. By comparing the intraconfigurational 4f emissions and their decay times with data from the literature, these 4f5d bands are assigned to transitions on Pr³⁺ ions on a site with C_4V symmetry. The fd excitation spectrum of the second site has a zero phonon line at 223.3 nm. Upon selective excitation in this band, only 4f5d emission is observed. Probably, these 4f5d bands correspond to Pr³⁺ ions on a O_h site. The third set of 4f5d bands has a 4f5d onset at 208 nm. By comparison of the luminescence spectra of the intraconfigurational 4f² transitions with literature data, these transitions are assigned to Pr³⁺ on an L site. Excitation in these 4f5d band yields ¹S₀ emission followed by emission from the ³P₀ state. The present results clarify some contradictions reported in the literature.     

Luminescent properties of trivalent praseodymium-doped lanthanum aluminum germanate LaAlGe2O7

The luminescent characteristics of Pr³⁺-activated LaAlGe₂O₇ were investigated. In response to excitement using 448 nm blue light, the emission spectra involved most of the ³P₀→³H_J transitions. The dominant emission came from the ³P₀→³H₄ transition at 487 nm. ¹D₂ fluorescence quenching was observed in highly doped samples and is related to the cross-relaxation processes among neighboring Pr³⁺ ions. In contrast with conventional Pr³⁺-activated phosphors, the extraordinary excitation spectra showed only intense f-f transition of Pr³⁺ ions, while the 4f-5d transition was eliminated. This is ascribed to photoionization. By analyzing absorption and excitation spectra, it is recognized that no efficient energy transfer occurs between Pr³⁺ and the host lattice in LaAlGe₂O₇.     

Luminescence of La3F3[Si3O9]:Ce

The luminescence properties of Ce³⁺ in La₃F₃[Si₃O₉] are reported. Excitation and emission bands corresponding to 4f¹→5d¹ transitions of Ce³⁺ were identified. The center of gravity of the 5d states lies at remarkable high energy (43.2×10³ cm⁻¹) for Ce³⁺ in a silicate compound. This high value is attributed to the combined oxygen/fluoride coordination of the Ce³⁺ ion. Emission from the lowest 4f5d level to the ²F_5/2 and ²F_7/2 levels was found at 32.4×10³ and 30.4×10³ cm⁻¹. These results are compared with literature data on silicates and fluorides. From the values found for Ce³⁺, predictions are made for the positions of the 4f5d bands of Pr³⁺ and Er³⁺ in La₃F₃[Si₃O₉]. For both ions, it is concluded that in this host lattice emission is expected from high lying 4fⁿ energy levels.     

Spectroscopic investigations and configuration-interaction-assisted crystal field analysis of Pr in YPO4 single crystal

An optical study of a Y_0.99Pr_0.01PO₄ single crystal is presented. Measurements of optical absorption, excitation, and emission by selective excitation into ¹D₂, ³P₀ and ³P₁, at different temperatures between 20 and 295 K, are described. A detailed account of the line assignments is given for absorption in the 4300-23 000 cm⁻¹ spectral range, and for emission in the 6400-23 000 cm⁻¹ range. The lifetimes of the emitting levels are determined. Vibronic sidebands accompanying absorption, emission and excitation spectra are reported. The decay processes of the ³P₁, ³P₀ and ¹D₂ levels are discussed. The aim of this study is a test of the configuration-interaction-assisted crystal field analysis as well as the accurate experimental determination of the energy level scheme. It was reported previously that the introduction of configuration interaction between the ground 4f² configuration with the excited 4f6p configuration always resulted in a decrease (≈50-60%) in the standard deviations between the observed and calculated energy levels. In the present work the 4f5d configuration is included as well. The crystal field is analysed in the theoretical D_2d site symmetry with and without configuration interaction. The results with 4f², 4f²+4f5d, 4f²+4f6p and 4f²+4f5d+4f6p are given. The calculation on the basis of the 315 (4f²+4f5d+4f6p) levels gives the best overall standard deviation lowering it by 75% with regard to the calculation on the 91 4f² levels only.     

Effects of Gd and Lu co-doping on the long afterglow properties of yellowish-orange phosphor Y2O2S:Ti, Mg

A new long afterglow phosphor Y₂O₂S:Ti⁴⁺, Mg²⁺ co-doped with Gd³⁺ and Lu³⁺ was synthesized by solid-state reaction in inert gas ambient. Its properties were systematically analyzed by X-ray diffraction (XRD), luminescence spectra, afterglow decay curves and thermoluminescence (TL) spectra. It was found that the long afterglow performance of Y₂O₂S:Ti⁴⁺, Mg²⁺ such as brightness and persistent time was largely improved when co-doped with Gd³⁺ and Lu³⁺. By analyzing the TL curve the activation energy E were calculated to be 0.64 eV for 388 K peak and 0.98 eV for 508 K peak, and the trap intensity related to 388 K peak is much stronger than that related to 508 K peak. The mechanism of the long afterglow was also discussed in this paper.     

Crystal fields of Pr in LiYF4 under pressure

Fluorescence spectra of LiYF₄:Pr³⁺ have been measured between 12,000 and 22,000 cm⁻¹ under pressures up to 10 GPa. In total, 25 crystal field energy levels were obtained and used for the determination of free-ion and crystal field parameters under pressure. According to the nephelauxetic effect, the free-ion parameters decrease with increasing pressure. The relative decrease is larger for the Slater than for the spin-orbit coupling parameter. This behavior is consistent with former studies on Pr³⁺ in different crystals and can be explained by a special covalency model. According to an effective D_2d symmetry, five crystal field parameters B₀²(f,f), B₀⁴(f,f), B₄⁴(f,f), B₀⁶(f,f), and B₄⁶(f,f) are non-zero. The pressure-induced changes of these parameters have been determined up to the maximum pressure of 10 GPa. In order to improve the calculation of the crystal field levels, the configuration interactions with the 4f¹6p¹ configuration have been taken into account. The effect of these interactions are also analyzed under pressure and distinct improvements of the energy level calculations have been obtained.     

Down-conversion near infrared emission in Pr, Yb co-doped Y2O3 transparent ceramics

Pr³⁺, Yb³⁺ co-doped Y₂O₃ transparent ceramics have been prepared by the solid state reaction and vacuum sintering. Down-conversion near infrared emission has been demonstrated upon a 482 nm excitation. The energy of the 482 nm blue photon was first absorbed by Pr³⁺ and then delivered to Yb³⁺. Possible energy transfer mechanisms from Pr³⁺ to Yb³⁺ have been discussed. Under the 482 nm excitation, the Pr⁴⁺-Yb²⁺ charge transfer state would not seriously influence the energy transfer process. The dominant one should be either the cooperative down-conversion or the two-step photon emission. The efficient down-conversion near infrared emission has potential application in enhancing the conversion efficiency of crystalline silicon solar cells.